Page 1
®
M i c r o F l ex
How to get a great shave
from your Remington
MicroFlex
Thank you for buying this premium shaver
from Remington
Inside you’ll find tips on using and caring for
your shaver to get the best shave possible.
® ™
®
™
®
Washable
Model Numbers
R-9100
R-9200
R-9250
R-9300
R-9350
R-TCT
IMPORTANT SAFETY
INSTRUCTIONS
When using an electric shaver, basic precautions should
always be observed,including the following. Read all
instructions before using this shaver.
DANGER
To reduce the risk of electric shock:
■ Do not reach for a shaver that has fallen into water.
Unplug immediately.
■ Do not use while bathing or in the shower.
■ Do not place or drop into water or other liquid.
■ Do not place or store shaver where it can fall or be
pulled into a tub or sink.
■ Except when charging, always unplug this shaver from
the electrical outlet immediately after using.
■ Unplug this shaver before cleaning.
WARNING
To reduce the risk of burns, fire, electric
shock, or injury to persons:
■ A shaver should never be left unattended when plugged
in, except when charging your rechargeable shaver.
■ Close supervision is necessary when this shaver is used
by, on, or near children or invalids.
■ Use this shaver only for its intended use as described in
this manual. Do not use attachments not recommended
by the manufacturer.
■ Keep the cord away from heated surfaces.
■ Never operate this shaver if it has a damaged cord
or plug, if it is not working properly, if it has been dropped
or damaged,or dropped into water.Return the shaver to
a service center for examination and repair.
■ Never drop or insert any object into any opening on
the shaver.
■ Do not use outdoors or operate where aerosol (spray)
products are being used or where oxygen is being
administered.
■ Do not use this shaver with a damaged or broken head
or cutter,as facial injury may occur.
■ A lw ays attach plug to shav e r,then to outlet.To disconnect,
turn all controls to "Off " ,then remove plug from outlet,
then detach power cord from the shaver for storag e .
■ Always store your shaver and cord in a moisture-free
a r e a . Make sure your cord is disconnected from
the shaver.
■ Do not plug or unplug shaver when hands are wet.
■ For household use only.
SAVE THESE
INSTRUCTIONS
Page 2
Getting a Close, Comfortable Shave
Congratulations on your purchase of a premium
Remington® MicroFlex® TCT™ Shaver. Your new
Remington®MicroFlex®TCT™is the only Rotary Shaver
with Total Closeness Technology™(TCT™). The MicroFlex
TCT™ has more blades, RPM’s and flexing head action*
than any rotary, to shave your entire face including the
tough spots like your neck and around your chin.
* More flexing head action as measured by vertical
movement at the center of head.
As with every shaver, your shave will improve over time.
So allow about three weeks to develop an effective
shaving style and for your beard to adjust to the new
shaver.The adaptation period may take a little longer
if your skin is sensitive, or if you alternate between
shaving methods.
The Best Technique
It’s simple to get a great shave from your new shaver.
Here are a few tips for getting the closest shave possible:
Always use a clean; dry shaver.
1 2
9
6
Make sure that the cutter head
assembly is in the locked
position.
Wait at least 15 minutes after
getting up before shaving, to
ensure the face is free of puffiness that may be present from
3
sleeping.
Make sure your face is clean and dry
before starting.
To Trim
To use the Easy-View®pop-up trimmer,
simply push the trimmer button up. The trimmer
will pop-up for use. Hold the shaver as shown
®
in the illustration. To conserve battery energy
(on rechargeable shavers only), it is recommended
to use the trimmer only when needed for trimming.
When through using, push the trimmer button
downward to lock into the off position.
To Shave
Push the on/off button to activate the
shaver for shaving.
The MicroFlex®TCT™needs no adjustments to the heads or cutters before
you shave. The floating heads will automatically adjust to the contours of your
face. It is not necessary to apply pressure while shaving…let the shaver glide
lightly on your skin. This gentle touch
makes shaving easier and helps avoid
possible skin irritation.
Use short, circular strokes. Use your
f ree hand to stretch your skin. T h i s
e n c o u rages your whiskers to stand out,
making it easier for them to enter the
cutting chamber.
•Always keep the protective headguard on the cutter head and keep
the trimmer in the “off” position when the shaver is not in use. The
headguard must be put on with the rear tab to the back of the shaver.
For a Better Shave…
To help maximize your shaver’s performance, consider using the
Remington®Pre-Shave Powder Stick (SP-5) or the Pre-Shave Lotion
with Aloe (SP-6). Just rub over your beard. Both absorb moisture and
facial oils, helping set up the hairs so they enter the cutting chamber
more easily.They make shaving quicker and more comfortable.
Trim Sideburns
Simply touch the comb-edge of the trimmer to
the desired line for neat, clean sideburns.
Trim Mustache
Hold shaver at desired trim line for a quick, easy,
professional trim. The trimmer can also be used to
trim the upper edge of your mustache.
Page 3
Cleaning your shaver:
TO ASSURE OPTIMAL PERFORMANCE, IT IS RECOMMENDED T H AT YOU CLEAN YOUR SHAVER AFTER EACH
USE. The cutting system of this shaver was designed t o
be cleaned by rinsing under warm running water or by
b r u s h i n g .
Cleaning your Remington®MicroFlex®TCT™ Shaver is
easy. (NOTE: With the R-9300/-9350/R-TCT model, the brush
icon will blink to remind you to clean your shaver.)
■ Open the hairpocket by squeezing
on both buttons and rotating away
from the body of the shaver. You may
blow out the stubble thoroughly, or
rinse the shaver head in water. Rinse
both sides of the head assembly.
■ At Least Once a Week:
For more complete cleaning, remove the cutter retainer
assembly from the hairpocket by turning the center knob
approximately 1/4 turn counter clockwise. Hold cutter retainer assembly as
shown, and remove head by turning
approximately 1/8 turn in the direction
shown. Brush clean both the head and
the cutter.Reassemble head to cutter
retainer assembly by aligning and turning head 1/8 turn in the opposite direction. Repeat this
process for each of the 3 heads. Clean each head and
cutter set one at a time to prevent mixing cutter components.(These should be kept as sets). After cleaning,
place cutter retainer assembly in the hairpocket,and
secure by turning center knob
approximately 1/4 turn clockwise.
■ To clean and lubricate your shaver’s cutters and head assembly,
apply Remington® Shaver Saver® (SP-4) Lubricant. The lubricant
helps remove hair clippings while reducing wear.A quick spray after
each shave keeps your shaver operating at peak performance.
Caution: Do not remove or replace the head assembly while
shaver is running or plugged into an electrical outlet as it may
cause damage to the unit’s cutters.
■ Worn or damaged parts should be replaced with Remington
®
replacement parts only.
When is it time to replace our heads
and cutters?
It is very important to replace your heads and cutters
when necessary to insure a close, comfortable shave
without irritation. We recommend they be replaced
every 12 months. Here are some signs of head and
cutter wear,indicating that replacement is needed.
(NOTE:R-9300/-9350/R-TCT cutter icon,R-9200 &
R-9250- the yellow LED- will blink when it is time to
replace the cutters.)
Irritation:
As the heads get excessively worn there may be some
skin irritation. This would be especially noticed when
applying After Shave lotion.
When the cutters wear you may feel a sense of
“pulling”and a loss of closeness when you shave.
This is an indication that it is time to replace your
heads and cutters.
Caution: Never put the shaver
completely under water.
Do not use any aggressive
cleansing agent as this may
destroy the shaver coatings.
H a i r p o c k e t
Head
Cutter
Page 4
Charging
Prior to using your shaver for the first time, put it on
charge for 24 hours.
To charge your shaver:
■ Make sure your shaver is turned off.
■ Connect the cord to the shaver and then the charging
adapter to the electric outlet. A charging indicator light
will come on.
■ Your shaver cannot be overcharged, so you can leave
it plugged in and charging between shaves.
■ Use only the charging adapter supplied with the
shaver.
■ The R-9100/-9200/-9300/-9250/-9350/R-TCT come
with a special feature that allows you to run the shaver
directly off the cord. Your shaver will not recharge while
you are shaving, so after shaving directly from the cord,
turn the unit off and set aside to charge.
■ The R-9100/-9200/-9300/-9250/-9350/R-TCT will
provide up to two weeks worth of shaving after a one
hour charge or a single shave after five
minutes of charging.
Model R-9100
has a green indicator light to show whether the shaver
is either fully charged or charging. A red low-battery
indicator illuminates to show when the shaver needs
r e c h a r gi n g .This also indicates ap p r o x i m at e ly 5 minutes
of shaving time left when indicator first comes on.
Model R-9200/-9250
features a green lighted fuel gauge that displays the
amount of charge remaining in 20% increments. When
only 20% of the charge remains,the recharge red
warning light illuminates.
Model R-9300/-9350/R-TCT
has an LCD display numeric indicator to show shaver
charge status in minutes remaining. When the Plug icon
comes on,it indicates approximately 5 to 6 min-
utes of shaving time left.
Troubleshooting:
■ If your R-9100/-9200/-9300/-9250/-9350/R-TCT shaver battery is completely discharged or the shaver has not been used for
an extended period of time, the shaver may not start when operated using the cord. If this condition occurs, charge the shaver fo r
ap p r o x i m at e ly five minutes before shaving.
■ Your R-9100/-9200/-9300/-9250/-9350/R-TCT c o r d / c o r d l e s s
s h aver should not be used strictly as a cord-operated shaver, as
continued cord only use will result in reduction of battery life.
■ In order to preserve the life of the batteries, they should be fully
discharged every six months and then fully charged for 24 hours.
World Wide Voltage (all MicroFlex®TCT™models)
You can take your shaver with you when you travel to just about
anywhere in the world. Your MicroFlex®TCT™shaver features
worldwide automatic dual voltage conversion providing AC current
between 100-240 volts AC, 50-60 Hz. Just plug it in to the local
outlet (you may need an adapter plug) and use as usual.
Your shaver will convert automat i c a l ly to the local current
requirements.
Battery Removal:
When your rechargeable shaver reaches the end of its useful life,
the batteries must be removed from the shaver and be recycled
or disposed of properly in accordance with your state and local
requirements.
THE FOLLOWING PROCEDURE SHOULD BE FOLLOWED
FOR BATTERY REMOVAL:
■ To avoid a possible electric shock hazard,unplug cord from electric outlet and shaver.
■ Open the head assembly by pressing the
head release buttons and lifting the head
assembly.Pull the entire head assembly off of
the shaver assembly.
■ Push the trimmer button up to open the
trimmer.
■ Remove the trimmer assembly by squeezing
the sides as shown in the picture.
■ Using a small Phillips head screwdriver,
remove the 3 screws from the back of the
s h av e r.
■ Pull or gently pry the shaver halves apart,
exposing the battery.
■ Pry the lower battery clip off.
■ Lift or pry the batteries out of the shaver.
■ Cut the wires on both ends of each battery and
remove them from the shaver.
CAUTION:DO NOT PUT IN FIRE OR MUTILATE
YOUR BATTERIES WHEN DISPOSING AS THEY M AY
BURST OR RELEASE TOXIC MAT E R I A L S .DO NOT SHORT CIRCUIT AS IT
MAY CAUSE BURNS. DISPOSE PROPERLY
IN ACCORDANCE WITH YOUR LOCAL AND STATE REQUIREMENTS.
®
The EPA certified RBRC
cadmium (Ni-Cd) battery indicates Remington Products Company,
L.L.C.is voluntarily participating in an industry program to collect
and recycle these batteries at the end of their useful life, when taken
out of service in the United States or Canada. The RBRC®program
provides a convenient alternative to placing used Ni-Cd b atteries
into the trash or the municipal waste stream, which
may be illegal in your area. Please call 1-800-8-BAT T E RY™for
i n fo r m ation on Ni-Cd bat t e ry recycling and disposal bans/restriction
in your area. Remington Products Company, L.L.C.’s involvement
in this program is part of our commitment to preserving our
e n v ironment and conserving our natural resources.
Battery Recycling Seal on the nickel-
Page 5
Easy-View
Trimmer
Rear Tab
®
On/Off Button
Percentage
of Charge
5 LED’s
(R-9200/
9250)
Low-Battery
Indicator (Red)
Shows When Shaver
Needs Charging
(R-9100,9200,9250)
Trimmer
Button
Brush
Storage Pouch
Head Guard
Head &
Cutter
Assembly
Charging
Indicator
(Green)
Models R-9100,
9200,9250
Remington®MicroFlex®TCT™Models
Which model is yours?
R-9100 Cord and cordless operation, rechargeable
(2 LEDs) with charging and low battery indicator lights,
R-9200 Cord and cordless operation, rechargeable
& R-9250 with percentage of charge and cutter
(7 LEDs) replacement,low battery (7 LED’s) indicator
R-9300/ Cord and cordless operation, rechargeable
R-9350/ 1-hour quick charge feature. Smart
R-TCT Shaver LCD with shaving time remaining
(LCD Display) indication, low battery, cleaning and cutter
and 1-hour quick charge feature. World wide
voltage: 100-240 volts, AC 50-60 Hz.
lights and 1-hour quick charge feature.
World wide voltage: 100-240 volts,
AC 50-60 Hz.
replacement cons. World wide voltage:
100-240 volts, AC 50-60 Hz.
Remington®Money-Back Offer
If within 30 days after you have purchased
your Remington®MicroFlex®TCT™Shaver,
you are not satisfied with your shaver and
would like a refund, just return your shaver,
together with the sales receipt, to the retailer from whom the shaver was purchased.
Remington will reimburse all retailers who
accept shavers within 30 days from date of
purchase. If you have any questions regarding this money-back guarantee, please call
1-800-736-4648 in the U.S. and 905-4709400 in Canada.
Full Two-Year Warranty
Remington warrants that your product,except as noted below,i s ,
on date of purchase, free from defect in material and workmanship.
Remington will correct any such defect without charge if you return
the complete product either in person or by mail,p o s t age paid,to a
Remington Company - owned Service Center or Authorized Serv i c e
Dealer within two years after date of purchase.
Do not return the product to the retailer from whom the product
was purchased.
This warranty does not cover damage by accident,m i s u s e , abuse or by
affixing an unauthorized accessory or alteration to the product, or by
connection of the product to any but the specific current and voltag e
i n d i c ated in an accompanying instruction booklet,or by any other conditions beyond our control.REMINGTON SHALL NOT BE RESPONSIBLE
FOR ANY INCIDENTA L ,SPECIAL OR CONSEQUENTIAL DAMAGES.I N
A D D I T I O N,THIS WARRANTY DOES NOT COVER THE FLEXIBLE HEAD
AND CUTTER A S S E M B LY ON OUR ROTA RY TYPE SHAV E R S .
ALL IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO IMPLIED
WARRANTIES OF FITNESS AND MERCHANTA B I L I T Y , ARE LIMITED IN
D U R ATION TO T W OYEARS FROM DATE OF ORIGINAL PURCHASE.
This warranty gives you specific legal rights,and you may also hav e
other rights that vary from state to stat e . Some states do not allow
the exclusion limitation of incidental or consequential damages or
l i m i t ations on how long an implied warranty lasts,so that the above
l i m i t ations and exclusions may not apply to you.
No responsibility,o b l i g at i o n , or liability is assumed for the installation
or maintenance of this product.
LCDDisplay (Models R-9300/-9350/R-TCT)
Page 6
Warranty service must be performed by a Remington Company owned Service Center or Authorized Service Dealer and damage or
loss of any kind resulting from servicing by any other person is not
covered under warranty. E n closed is a listing of Company - ow n e d
S e rvice Centers. Authorized Service Center Dealers may be found
in the yellow pages of your directory. If you wish,you may mail
the product,postpaid,to Remington Products Company,L.L.C.,
60 Main Street,B r i d g e p o r t , CT 06604 A t t e n t i o n :S e rvice Department.
U.S. Warranty Service
In the United States, service is pro v i d e d
by our Company-owned Service Centers
and over 300 Authorized Service Dealers.
The addresses of our Company-owned
S e rvice Centers are enclosed. For the
a d d ress of your nearest Authorized Serv i c e
D e a l e r, please consult the Yellow Pages
under “Shaver - Electric - Repair.” If you
wish, you may mail the product, postpaid,
to Remington Products Company, L.L.C.,
60 Main Street, Bridgeport, CT 06604,
Attention: Service Depart m e n t .
International Warranty Service
S e rvice under the Remington warranty can
be obtained outside the United States by
Remington-Authorized Distributors and
S e rvice Dealers. Please consult your local
telephone dire c t o ry for the nearest location.
For questions or comments,please write:
Remington Products Company,L . L . C .
50 Commerce Drive
Tr u m b u l l ,CT 06611-5403
A t t e n t i o n :Consumer A f f a i r s
Questions or Comments: Please call
Z
1-800-736-4648 in the U.S.or 905-470-9400 in Canada.
Visit us at http:\\www. r e m i n g t o n - p r o d u c t s . c o m
R e m i n g t o n ,M i c r o F l e x ,T C T,Total Closeness Te c h n o l o g y, E a s y - V i e w
and Shaver Saver are trademarks of Remington Corporat i o n ,L . L . C .
© 2001 R.P. C ,L . L . C .Job #S01-079 7/01 Part No.12642
U . S . Pat e n t s :5,390,416; 5,408,749 and Patents Pe n d i n g
Canada Pat e n t s :1 , 7 4 8 ,2,091,039 and Patents Pe n d i n g :
Remington Products Company,L . L . C .
60 Main Street
B r i d g e p o r t , CT 06604
MADE IN CHINA.
Remington Products (Canada) Inc.
61 Amber Street
M a r k h a m ,Ontario L3R 3J7
Loading...