Remington PF7500AU User guide

TITANIUM COMFORT
PRO

USE & CARE

MANUAL

PLEASE READ

PRIOR TO USE

To register your product go to:

www.remington-products.com.au

www.remington.co.nz

2 YEAR WARRANTY

PF7500AU

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic precautions should
always be observed, including the following.

READ ALL INSTRUCTIONS BEFORE USING

For additional protection, the installation of a residual current
device (rcd) having a rated residual operating current not
exceeding 30 mA is advisable in the electrical circuit supplying
the bathroom. Ask your installer for advice.

WARNING: TO REDUCE THE RISK OF BURNS, ELECTROCUTION
AND FIRE OR INJURY TO PERSONS

DANGER: As with most electrical appliances, electrical parts are
electrically live even when the switch is off.

• The appliance should never be left unattended when plugged into
a power outlet, except when charging the appliance.

• This appliance should not be used by children or other persons
with reduced physical, sensory or mental capabilities or lack
of experience and knowledge unless they have been given
supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children shall not play
with the appliance. Cleaning and user maintenance shall not be
made by children without supervision.

• Never operate this appliance if it has a damaged cord or plug,
if it is not working correctly, if it has been dropped or damaged,
or dropped into water. If the supply cord or plug of the appliance
is damaged it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard. It
cannot be repaired. Keep the cord away from heated surfaces.

• Charge, use and store the product at a temperature between 0°C
and 32°C.

• Do not use outdoors or where aerosol (spray) products are being
used, or where oxygen is being administered.

• Do not use this appliance with damaged or broken tracks, foils or
cutters, as injury may occur.

2

• For use on facial hair only. Not intended for shaving the hair on
your head.

• Do not plug or unplug the appliance with wet hands.

• For household use only.

• Do not place or store the appliance or charging adaptor where it
can fall or be knocked into a sink or bath.

• Do not place in or drop into water or any other liquid for extended
periods of time.

• If an appliance falls into water, “unplug it” immediately. Do not
reach into the water.

• Unplug the charging adaptor from the electrical outlet immediately
after fully charging.

• Unplug and switch off this appliance before cleaning it.

• Use this appliance only for its intended use as described in this
manual.

• Do not use attachments not recommended by Remington.

• Never drop or insert any object into any opening of this appliance.

• Always store the charging adaptor in a moisture-free location.

• Do not use on people who are asleep.

• Do not use an extension cord or a voltage converter with this
appliance.

• Do not wrap the cord around the appliance.

Remington strongly recommends that an approved Safety Switch
(Residual current device) be installed to protect all bathroom power
outlets. Ask an electrical contractor for advice.

SAVE THESE INSTRUCTIONS

3

PF7500AU TITANIUM COMFORT PRO

USE & CARE INSTRUCTION MANUAL

Thank you for purchasing your new Remington® Titanium Comfort Pro.

Inside this manual you will find tips on using and caring for your shaver.

4

3

1

KEY PARTS

1. On/Off button

2. Foils

3. Cutter assembly

4. Intercept trimmer

5. Hair pocket

6. Pop up trimmer (not shown)

7. Charging pins (not shown)

2

5

6

7

Also Includes

• Head guard

• Power adaptor

• Cleaning brush

• Storage pouch

4

PF7500AU SPECIFICATIONS

A

B

Power System Lithium Rechargeable

Full Charge Time 2 hours

Cordless Shave Time 50 minutes

Quick Charge Yes

Indicators Charging/Low Battery

Volt ag e Type Worldwide

Replacement Part SPF-PFAU

Water Resistance Washable Head

CHARGING

NOTE: BEFORE USING, READ THE IMPORTANT SAFETY INSTRUCTIONS IN
FRONT OF THE MANUAL.

1. Connect the cord to the shaver and then to the electrical outlet
(Diagrams A & B). The charging indicator light will glow green.

2. Your shaver will have a partially charged battery. We recommend that you charge
the battery for the full charge time prior to the first use.

3. Charge shaver to a full charge before its first use.

4. Use shaver until recharge is required.

Quick Charge

A 5 minute quick charge will allow for 3 minutes of shaving.

CAUTION!

• Make sure the shaver and your hands are dry when charging the shaver.

• Always charge the shaver in a cool, dr y place.

5

SHAVING

C

D

1. Press power button to turn on. (Diagram C)

2. Stretch the skin with your free hand so the hairs stand upright.

3. Hold the shaving head so the foils and intercept trimmer touch your skin
simultaneously. Apply light pressure while shaving and use linear strokes.
(Diagram D)

SHAVING TIPS (DRY)

• Ensure your skin is free of oils.

• Wait at least 15 minutes after getting up before shaving, to ensure your face is
free of puffiness that may be present from sleeping.

• Hold the shaver 90° to your skin.

• Stretch your skin and shave against the direction of your beard growth using linear
strokes.

• For areas such as the chin and neck where hair grows in different directions use
small circular strokes.

• While shaving do not press hard against the skin to avoid skin irritation and/or
damage to the foils.

**We recommend that you use your new shaver daily for up to four
weeks to allow time for your hair and skin to become accustomed to the
new shaving system**

6

CLEANING & MAINTENANCE

E

F

G

H

The shaver is a washable appliance. The head assembly part may be cleaned
under water.

NOTE: * *When cleaning your shaver, make sure the shaver is turned off and
disconnected from the power cord.**

CAUTION!

• To clean the external sur faces of the shaver, use a damp cloth. Do not use strong
detergents or other chemicals.

• To dry, wipe the surface of the shaver with a dry towel. Do not use a hair dryer or
heater to dry the shaver.

NOTE: Lubricate cutters after rinsing.

DAILY CLEANING

NOTE: We recommend following these steps after each use.

1. Grasp the front and back of the cutter assembly and pull away from the shaver
body. (Diagram E)

2. Tap out excess hair shavings and use the cleaning brush to sweep any loose hairs
away. (Diagrams F-G)

3. Rinse the head of the assembly under running water. Gently towel dry or leave to
air dr y.

4. Replace the head assembly when dry by placing the assembly on top of the hair
pocket, press down and click into place. (Diagram H)

NOTE: Lubricate teeth of trimmer with oil every six months.

7

Price each

Face Saver: Pre-shave Powder Stick

handling

Shaver Saver: Aerosol Spray Cleaner

Shaving Heads & Cutters for PF7500AU

Price each

Qty Amount

NZD

AUD

$

$

$14.95 NZD

$44.95 NZD

$11.95 AUD

$39.95 AUD

SP4

7.50

$

$

$

$

Sub Total

SP5 $11.95 AUD $14.95 NZD

TOTAL

Postage &

Spectrum Brands Australia Pty Ltd

Locked Bag 3004

Braeside, VIC 3195

AUSTRALIA

SPF-PFAU

eplacement

Article

R

Remington is a Registered Trademark

of Spectrum Brands, Inc., or one

of its subsidiaries.

MONTHLY CLEANING

I

K

L

L

J

1. Perform steps 1-3 of the daily cleaning.

2. Place a drop of soap on each cutter and hairpocket. (Diagram I)

3. Brush the soap around vigorously with the cleaning brush. (Diagram J )

4. Add a small amount of water to the cutters.

5. Replace the foil assembly. (Diagram K)

6. Turn the shaver on for approximately 30 seconds.

M

7. While shaver is running rinse the foils under running water. (Diagram L)

8. Turn off shaver, remove foil assembly and rinse the cutters, hair pocket and foil
assembly throughly. (Diagram M)

9. Shake off excess water.

10. Replace foil assembly.

11. Allow shaver to dry before next use.

10

REPLACING THE FOIL & CUTTERS

It is very important to replace the foil and cutters when necessary to ensure a close,
comfortable shave without irritation. We recommend they be replaced every 6 months.
Here are some signs of head and cut ter wear, indicating that replacement is needed:

• Irritation: As the heads get excessively worn you may experience some skin
irritation. This would be especially noticeable when you apply moisturizing lotion.

• Pulling: When the cut ters wear you may feel a sense of pulling and a loss of
closeness when you shave. This is an indication that it is time to replace your
heads and cutters.

Replacement foil & cutters may be obtained from your local retailer, or directly from
Remington

®

. Simply fill out the enclosed accessory order form - refer to page 8 & 9, or
alternatively your order can be processed over the phone via the Remington® Service
Hotline - refer to page 14.

HOW TO REPLACE THE FOIL & CUTTERS

Remove the foil assembly by grasping the front and back of the foil assembly and lift
upwards to remove from the hair pocket.

• Grasp each cut ter between your thumb and forefinger and pull upwards to remove.

• Snap each new cutter assemblies into the top of the drive shaf t.

NOTE: Do not push on the ends of the cutters as this may cause damage and
reduce their effectiveness.

• Insert the new foil assembly on top of the hair pocket, press down and click into

place.

THIS PRODUCT IS NOT SU ITAB LE TO USE IN THE BATH OR SHOWER .

This product conforms to radio frequency interference requirements

Any product purchased and used commercially carries a limited 90 Day Warranty.

11

BATTERY DISPOSAL

NOTE: The battery is not intended to be removed or replaced under normal use.
The only time the battery should be removed or the unit opened or disassembled,
is at the end of the product’s useful life before it is discarded.

BATTERY DISPOSA L

The PF7500AU shaver contains a lithium-ion battery. Once the trimmer has reached
the end of its life, to ensure proper disposal of the product, please take the appliance
to a recycling centre, where the internal rechargeable battery should be removed by a
professional and recycled separately.

For more information about recycling of electrical and battery operated appliances,
please contact your local council of fice or your household waste disposal service.

CAUTION: Do not put in the fire or mutilate your batteries when disposing as
they may burst and release toxic materials. Do not short circuit as it may cause
burns.

MONEY BACK OFFER – AUSTRALIA / NEW ZEALAND ONLY

If within 6 0 days you are not fully satisfied with your Remington® shaver, just return the shaver
with this completed coupon and a copy of your Australian/ New Zealand purchase receipt to

®

Remington
Please allow 6-8 weeks for your cheque to arrive.

. In return, we will send you a cheque for the full purchase price of the shaver.

Name:

Address:

City:

State: Postcode:

Contact No: Area Code: Ph:

Product Model number:

Is this the first Remington shaver you have owned/purchased? Yes No

What is the reason you are returning this product ?

12

Spectrum Brands Australia Pty Lt d and Spectrum Brands New Zealand Limited

WARRANTY AGAINST DEFECTS

In this warranty:

Australian Consumer Law means the Australian consumer law set out in Schedule 2 to the
Competition and C onsumer A ct 2010;

CGA means the New Zealand Consumer Guarantees Act 1993;

Goods means the product or equipment which was accompanied by this warranty and

purchased in Australia or New Zealand, as the case may be;

Manufacturer, We or us means:

1. for Goods purchased in Austr alia, Spectrum Brands Australia Pty Ltd

ACN, 007 070 573; or

2. for Goods purchased in New Zealand, Spectrum Brands New Zealand Limited,

as the case may be, cont act det ails as set out at the end of this warrant y;

Supplier means the authorised distributor or retailer of the Goods that sold you the Goods
in Australia or in New Zealand; and

You means you, the original end-user purchaser of the Goods.

1. Our goods come with guarantees that cannot be excluded under the Australian Consumer

Law, or the CGA. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.

2. The benefits provided by this Warranty are in addition to all other rights and remedies in

respect of the Goods which the consumer has under either the Australian Consumer Law
or the CG A. The original purchaser of the Goods is provided with the following Warranty
subject to the Warranty Conditions:

3. We warrant the Goods for all parts defective in workmanship or materials for the period of

two (2) years from the date of purchase ( Warranty Period). If the Goods prove defective
within the Warranty Period by reason of improper workmanship or material, we may, at our
own discretion, repair or replace the Goods without charge.

Warranty Conditions

4. The Goods must be used in accordance with the manufacturer’s instructions. This Warrant y

does not apply should the defect in or failure of the Goods be attribut able to misuse, abuse,
accident or non-observance of manufacturer’s instr uctions on the par t of the user. As far as
the law permits, the manufacturer does not accept liabilit y for any direct or consequential
loss, damage or other expense caused by or arising out of any failure to use the Goods in
accordance with the manufacturer’s instructions.

5. Exhaustible components (such as shaver heads, cutter s and foils) of the Goods are included

under this Warrant y only where there is a defect in workmanship or materials used.

6. The warr anty granted under clause 3 is limited to repair or replacement only.

7. Any par ts of the G oods replaced during repairs or any product replaced remain the proper ty

of the manufacturer. In the event of the Goods being replaced during the Warranty Period,
the warranty on t he replacement Goods will expire on the same date as for the Warranty
Period on the original Goods which are replaced.

13

8. In order to claim under the warranty granted under clause 3 you must:

(a) Retain this warranty with your receipt /proof of purchase; and
(b) Return the Goods to us at the relevant address below or to the Supplier by prepaid
freight within the Warrant y Period accompanied with ( i) the legible and unmodified original
proof of purchase, which clearly indicates the name and address of the Supplier, the
date and place of purcha se, the product name or other product serial number and (ii) this
warranty.

9. This warranty is immediately void if:

(a) Any serial number or appliance plate is removed or defaced;
(b) The Go ods have been serviced or otherwise repaired by a person not authorised to do so
by us or where non approved replaced parts are used.

10. The Goods are designed for domestic use only. A limited 9 0-day Warranty applies to any

industrial or commercial use of the Goods. The Goods must be connected to the electrical
voltage requirements as specified in the ratings label located on the G oods.

11. This warranty does not cover the cost of claiming under the warranty or transport of the

Goods to and from the Supplier or us.

12. This warranty is only valid and enforceable in Austr alia against Spectrum Brands Australia

Pty Ltd and in New Zealand against Spectrum Brands New Zealand L imited.

Contact us or the Supplier for further details.

Spectrum Brands Australia Pty Ltd

Locked Bag 300 4
Braeside, VIC 3195
AUSTRALIA
Customer service in Australia: 180 0 623 118
E-mail: [e-mail]
Website: www.remington-products.com.au

Spectrum Brands New Zealand Limited

PO Box 9817
Newmarket, Auckland 1149
NEW ZEALAND
Customer service in New Zealand: 0800 736 776
E-mail: [e-mail]
Website: www.remington.co.nz

REMINGTON SERVICE HOTLINE

Aust ralia 1800 623 118 (toll free)
New Zealand 08 00 736 776 (toll free)

®

Registered Trade Mark of Spectrum Brands, Inc., or one of its subsidiaries

Made in China to the Specifications of Spectrum Brands, Inc.

©

2017 Spectrum Brands Inc.
RE V: 08/17
PART NO: T22- 0005191

14