Remcor 90660, TJ200-ABC Installation Manual

Remcor Incorporated
500 Regency Drive
Glendale Heights, IL 60139
Telephone [phone]
Facsimile [phone]

FOR

CONNECTING REYNOLDS CF--3--TT ICEMAKER

TO

REMCOR TJ45/90/200--A, --ABC, DISPENSERS

CAUTION: Disconnect power before installation of tube kit.

1. Refer to the respective model owner’s manual (template drawings) for locating the openings in the counter
for the ice feed tube, icemaker control bulb, and utilities.

2. Install gasket in feed tube hole in hopper as shown.

3. Clamp metal fitting and gasket to icemaker evaporator as shown.

4. Feed the dispenser end of the tube up through the counter and cabinet and into the hopper through
the gasket.

5. Temporarily position feed tube onto the icemaker fitting until completely seated. Adjust icemaker position as
required. Check feed tube extension inside hopper. Mark tube for trimming to provide 1? extension. Re­move the feed tube, and cut as marked being sure to remove any burrs or rough edges. Slide the insula­tion on the feed tube. Reinstall feed tube in dispenser and clamp feed tube to icemaker fitting as shown.

6. Route the icemaker control bulb along the outside of the dispenser rear cabinet and into the hopper as
shown. The minimum bulb lengths required are:

TJ45/90 -- 6 ft.
TJ200 -- 8 ft.

Install insulating tubing and mount the bulb to the deflector assembly . Be careful to avoid damaging or kink­ing the bulk capillary tubing. Do not allow the bulb to contact any cold surfaces or false sensing will occur.
Route the bulb away from electrical terminals, moving parts or sharp metal edges.

7. Follow all markings on the icemaker and instructions provided with both the icemaker and dispenser.

906601

BULB BEHIND

CROSSBRACE

ICEMAKER BULB

ROUTE AS SHOWN

CLAMP

DISPENSER

ICEMAKER

CLAMP

INSULATION

ICE FEED TUBE
NOZZLE CLAMP

FEED TUBE CLAMP DETAIL

DISPENSER

ICEMAKER

FRONT

ICE
FEED
TUBE

FIGURE 1. INSTALLATION

90660 2

ROUTE ICEMAKER
BULB AS SHOWN

DETAIL
“B”

DETAIL
“A”

FEED
TUBE

PVC

COUPLING

METAL

FITTING

GASKET

DISPENSER

DISPENSER

INSULATION

ICEMAKER ICEMAKER

INSULATION

FEED
TUBE

WARNING

FEED TUBE MUST BE

GASKET

FLUSH AGAINST METAL

FITTING

CLAMP

ICEMAKER

EVAPORATOR

SEAL
WITH
RTV

DETAIL “B”

HOPPER

DETAIL “A”

FIGURE 2. INSTALLATION

906603

STAINLESS
DEFLECTOR

END OF INSTALLED
BULB PROTRUDES

AGITATION
BULB -­BOTTOM

ALUMINUM
PLATE

APPROX 1/4? TYPICAL

FIGURE 3. DEFLECTOR ASSEMBLY TJ45--A AND TJ90--A MODELS

DEFLECTOR ASSEMBLY

AGITATION BULB

INSTALL BARE BULBS
AS SHOWN ABOVE

ICEMAKER
BULB -- TOP

INSULATING TUBING
UP TO DEFLECTOR

ICEMAKER BULB
WITH INSULATION
TUBING UP TO
DEFLECTOR

FIGURE 4. HOPPER INTERIOR TJ45--A AND TJ90--A MODELS

90660 4

STAINLESS

DEFLECTOR

ICEMAKER

BULB

END OF INSTALLED

BULB PROTRUDES

APPROX. 1/4-IN

DEFLECTOR ASSEMBLY
INSTALL BARE BULBS
AS SHOWN ABOVE

ICEMAKER BULB
WITH INSULATION
TUBING UP TO
DEFLECTOR

FIGURE 5. DEFLECTOR ASSEMBLY/HOPPER INTERIOR TJ200--A MODEL

906605