Page 1
7000FE
END CUTTING SYSTEM INSTRUCTION MANUAL
Page 2
Page 3
CONGRATULATIONS
We would like to thank you, and congratulate you for purchasing
the 7000FE end cutting system from Reliable.
Everything you need to start end cutting is included. A heavy-duty
4” cutting head with a manual sharpener, 96” track with lifter set
and uprights with a piece goods bar for your fabric.
For your safety and to fully enjoy the advantages of this product,
please take a few minutes to read all of the important safeguards
and care instructions. Keep this manual handy for your reference.
1
Page 4
SET-UP INSTRUCTIONS
1. SETTING UP THE FABRIC ROLL STAND
(CB-13)
A) Fix the stands on both sides at the end of table
and tie the drive.
B) Lie down the fabric roll on the fabric stands.
2. SETTING UP THE CLAMPS (CB-02)
A) Find and fix two clamps on both sides of the
table and tie the drive.
B) Find and fix the twin spring on the clamp
of the operated side (single spring set up on
another clamp).
C) Attach the spring connector (CB-17) on the bar
lifter stands (CB-10).
3. SETTING UP THE BELT FOR THE BAR
LIFTER (CB-25)
A) Find the green plastic belt and fix one end into
the belt connector (CB-08) clamp.
B) Pull the other end of the belt across the
plastic roller.
4. SET UP RAIL (CB-01)
A) Lie down the rail on two clamps and secure
with a bolt.
5. SETTING UP THE RAIL (CB-01)
A) Take off the lift handle (CB-11A) and spring
(CB-49).
B) Insert the cutter plate into the rail and restore
(CB-11A) and (CB-49).
6. CONNECTING THE POWER
A) Find the electric cable and connect the
socket (CE-04) with the plug (CE-03) and connect another cable end with the power source.
B) Short handle: turn on operating switch
(CE-05) for machine to start.
C) Long handle: power will be started when
the cutter head is pushed out from the
operated side.
IMPORTANT: Please keep the lift handle (CB-11A), twin spring clamp (CB-02) and cutter
hand on the same side of operation when the machine is installed.
2
Page 5
MOTOR ASSEMBLY & ACCESSORIES
CB-01
CB-02
CB-03
CB-05
CB-06
CB-07
CB-07A
CB-08
CB-10
CB-11A
CB-11
CB-12
CB-13
CB-14
CB-15
CB-16
CB-17
RAIL
CLAMP
BAR LIFTER ELBOW
PLASTIC ROLLER
ROLLER SHAFT
SCREW FOR RAIL
SCREW FOR LOFT HANDLE
BELT CONNECTOR FOR BAR LIFTER
BAR LIFTER STAND
LIFT HANDLE (PLASTIC)
LIFT HANDLE (ALUMINUM)
FABRIC ROLL HOLDER
STAND FOR FABRIC ROLL
SCREW DRIVE FOR CLAMP
SCREW DRIVE FOR FABRIC ROLL STAND
NUT FOR CLAMPING SCREW
SPRING CONNECTOR
CB-18
CB-19
CB-22
CB-23
CB-24
CB-25
CB-26
CB-27
CB-28
CB-29
CB-30
CB-31
CB-42
CB-47
CB-49
CB-50
W-019BB(W)
SQUARE SEAT
ROLLER SEAT
SPRING
FABRIC ROLL HOLDING ROLLER
STEEL PIECE
BELT FOR BAR LIFTER
RAIL RUBBER TAPE
CLOTH PRESS TRACK
BEARING FOR FABRIC ROLL HOLDER 626
BUSH BEARING LM-13
BUSH CLIP
BOLT FOR BAR LIFTER ELBOW
HOLDING ROLLER PLASTIC ARROW
LIFT HANDLE SWITCH SET
SPRING
C. TYPE SPRING
MOTOR(220V)G
3
Page 6
STANDARD & BASE ASSEMBLY
CA-01(W)
CA-01A
CA-01B
CA-01C
CA-02
CA- 03
CA-04
CA-04A
CA-04C
CA-04E
CA-05
CA-06A-1
CA-07A
CA07B
CA-09
CA-1 0
CA-11A
CA-11(W)
CA-1 2
CA-1 3
CA-1 4
CA-1 5
4
MOTOR COVER (WHITE)
CARBON BRUSH
CARBON BRUSH COVER
CARBON BRUSH HOLDER
TERMINAL BOX
COVER FOR TERMINAL BOX
SHORT HANDLE
LONG DRIVE HANDLE
CONNECT FOR LONG HANDLE
SCREW FOR LONG HANDLE CONNECTOR
MOTOR PLATE
MOTOR STAND
LOWER BLADE ARM
LOWER BLADE ARM ADJ
COLLAR FOR KNIFE
LOCK NUT FOR KNIFE
SCREW FOR BLANCE IRON
BLANCE IRON (WHITE)
KNIFE COVER
KNIFE GUARD
MOTOR COVER PIECE
SPRING FOR COLLAR
CA-1 6
CA-1 7
CA-1 9
CD
CD-01
CD-48-E
CD-02
CD-03
CD-04
CD-05
CD-06
CD-07
CE-01
CE-01C
CE-02BB
CE-03
CE-04
CE-04A
CE-05
CE-05-01
CE-06
ROUND KNIFE
LOWER BLADE
SWITCH PLATE
GRINDER ASSEMBLY
GRINDER STONE
SWITCH CABLE (GLORY)
BEARING
BRAZE SET FOR BEARING
PLATE FOR GRINDER STONE
SPRING
PUSH BUSH
GRINDER SUPPORT
MOTOR AXIS
MOTOR COIL
COUNTER (220V)
CABLE PLUG
SOCKET
CABLE
OPERATING SWITCH
LONG DRIVE HANDLE OPERATING SWITCH
COUNTER SWITCH
Page 7
5
Page 8
RELIABLE PRODUCTS WARRANTY
Reliable Corporation (“Reliable”) warrants to original purchaser of its products that
every product sold by Reliable (a “Reliable Product”) is free from defects in material and
workmanship for a period of one year from the date of purchase if properly used and
maintained. Subject to the conditions and limitations set forth below, Reliable will either
repair or replace any part of a Reliable Product that proves defective by reason of improper
workmanship or materials. If the defective Reliable Product is no longer available and cannot
be repaired effectively or replaced with an identical model, Reliable shall replace the defective
Reliable Product with a current Reliable Product of equal or greater value. Repaired parts or
replacement products will be provided by Reliable on an exchange basis, and will be either new
or refurbished to be functionally equivalent to new. If Reliable is unable to repair or replace
a Reliable Product, it will refund the current value of that Reliable Product at the time the
warranty claim is made.
This limited warranty does not cover any damage to a Reliable Product that results from
improper installation, accident, abuse, misuse, natural disaster, insufficient or excessive
electrical supply, abnormal mechanical or environmental conditions, wear and tear resulting
from normal use of the product, or any unauthorized disassembly, repair, or modification. This
limited warranty does not extend to any indirect, consequential or incidental damages that
may be suffered by a user or from the use of a Reliable Product, including without limitation,
any liability for third party claims for damage, and is limited to the amount paid by the original
purchaser Reliable Product with respect to which this limited warranty protection applies.
This limited warranty does not apply with respect to products that have been altered or which
are missing serial numbers or for products not purchased directly from Reliable or a dealer
authorized by us to sell Reliable Products.
This limited warranty is the only warranty that applies to any Reliable Product, supersedes any
and all terms that may be contained in any other document or purchase order and may not be
altered or amended except expressly in writing by Reliable.
To obtain a repair or replacement under the terms of this warranty, please contact our
customer service group at 1-800-268-1649 or at support@reliablecorporation.com.
You will be required to submit an original receipt via fax or e-mail. The receipt must reflect that
you are the original purchaser, the product was bought directly from
us or from an authorized Reliable dealer and that the warranty claim is being made within the
warranty period. You will be issued a return authorization number (RA#) and asked to ship the
defective product together with proof of purchase and RA#, prepaid insured to the following
address:
Reliable Corporation, 5-100 Wingold Avenue, Toronto, ON M6B 4K7. Freight collect shipments
will be refused. The risk of loss or damage in transit will be borne by
the customer. Once Reliable receives the defective product, it will initiate the repair or
replacement process.
If you have any questions regarding this warranty, you may write to:
Reliable Corporation
100 Wingold Avenue, Unit 5
Toronto, Ontario
Canada M6B 4K7
www.reliablecorporation.com
6
Page 9
Page 10
1 800 268 1649
www.reliablecorporation.com
Loading...