Reliable 6050SM User Manual
SEWQUIET
6050SM
INDUS TRIAL DC BRUSH LESS SERVOMOTOR
SERVOMOT EUR INDUSTRI EL À COURANT CONTI NU SANS BALAI
SERVOMOTO R INDUSTRIAL SI N ESCOBILLA S DE CD
INSTRUCTION MANUAL
GUIDE D’UTILISATION
MANUAL DE INSTRUCCIONES
ENGLISH 01
FRANÇAIS
ESPAÑOL 15
08
SEWQUIET 6050SM
INDUSTRIAL DC BRUSHLESS
SERVOMOTOR
INSTRUCTION MANUAL
ENGLISH
01
RELIABLE. RIGHT THERE WITH YOU.
At Reliable, we do what we love, and take pride in doing it right.
You want what’s best for the people, places and things that matter
in your life – from where you live to what you wear. So do we. From
the start, we approach every product with a craftsman’s attention
to detail and passion for making it right. Quality, functionality,
design and customer service play an equally important part in
delivering what’s right for you. Whether you are an advanced
sewer or a beginner, the 6050SM’s microprocessor controller
gives the user an unparalleled connection to the sewing machine,
allowing for speed or detailed work.
For your safety and to fully enjoy the advantages of this product,
please take a few minutes to read all of the important safeguards
and care instructions. Keep this manual handy and review the
product warranty for your reference.
02
PULLEY COVER INSTALLATION INSTRUCTIONS
1. Slide the pulley cover off of the bracket.
2. Align the bracket to the screw holes on the motor. Place two mounting screws (sup-
plied) onto the bracket and fasten it to the motor. (Required angle indicated).
3. Slide the pulley cover onto the bracket.
4. Fasten the screw on the bottom of the pulley cover to secure it to the bracket.
03
PROGRAMMING
MACHINE TYPE
Basic single needle
Basic two needle/needle feed
Walking foot (Except MSK-1541S)
Walking foot auto lubrication
MSK-1541S/4200SW
Sergers – overlock
Blindstitch
Zig-Zag (20U style)
Zig-Zag (High Speed)
Zig-Zag Walking foot
SPEED
SELECTOR
34
22
16
20
29
40
12
16
22
20
PULLEY
SIZE
60MM
60MM
60MM
60MM
60MM
60MM
60MM
60MM
60MM
60MM
APPROX.
SPEED RPM
4500
3000
1500
1720
2160
5260
1200
1650
2000
1925
SPECIFIC
SPEED
5000
3500
1800
2000
2500
6500
2500
2000
3000
2000
In order to prevent possible damage to your machine, if the machine you have
is not on the categories list, please call your dealer to obtain the correct speed
setting and pulley size.
HOW TO CHANGE THE SPEED
• Press the “P” button and the LED will change to n0
• Press the “S” button to change the speed in increments of 100rpm
• Continue to press the “S” button until the desired speed setting is displayed
• Press the “P” button to save the selection
HOW TO CHANGE THE DIRECTION
• Press the “P” button 4 times until the LED reads n3
• Press the “S” button to select between “0” and “1”
• Select “0” and the motor will run counterclockwise
• Select “1” and the motor will run clockwise
• Press the “P” button to save the selection.
04
HOW TO ENABLE AND DISABLE THE NEEDLE
POSITIONING FUNCTION
• Press the “P” button 2 times and the LED will change to "n1"
• Press the “S” button to select between “0” and “1”
• Select “0” to disable the needle positioning function
• Select “1” to enable the needle positioning function
• Press the “P” button to save the selection
HOW TO SET THE STOP POSITION OF THE NEEDLE:
This programming should only be used when the OPTIONAL synchronizer is
installed. Order separately.
• Press the “P” button 3 times and the LED will change to "n2"
• Press the “S” button to select between “0” and “1”
• Select “0” and the needle will stop in the down position
• Select “1” and the needle will stop in the up position
• Press the “P” button to save the selection
SETTING THE “F” MODE N5 TO N6
STEP 1:
• First, press and hold the “S” button. Then press and hold the “P” button. Keep
both buttons pressed until “F” appears on the display.
• When “F” appears, release both buttons and then press the “P” button to
advance to parameter “5”.
• When “5” appears, keep pressing only the “S” button to advance to “0” (low
speed start disabled).
• Press the “P” button to save the value.
STEP 2:
• First, press and hold the “S” button. Then press and hold the “P” button and
keep both buttons pressed until “F” appears on the display.
• When “F” appears, release both buttons and then press the “P” button to
advance to parameter “6”.
• When “6” appears, keep pressing the “S” button only to advance to “9” (step
sewing higher value).
• Press the “P” button to save the value.
• Switch the power off and then switch the power back on to complete the
programming.
* Please note: When sewing dense materials (ex. Tooling leather), a size 22 leather
point needle is recommended.
05
WHEN THE DISPLAY IS SHOWING E5
• Press and release the "S" button and the display will change to "P"
• Press the "P" button 2 times and the display will changes to "n1"
• Press the "S" button and the display will change to "1"
• Press the "S" button again and the display will change to "0"
• Press the "P" button to save the value
• Turn the power off and then on again to complete the programming.
ERROR CODES
ERROR CODE
E1: Operational failure.
E2: Over current or under voltage.
E3: The board cannot read the
parameter.
E4: Hall signal error.
E5: Needle position problem.
SOLUTION
E1: Machine is locked. Check to see if the
machine is difficult to turn, or if there is a
lack of lubrication.
E2: Check the power source to ensure that
the voltage is within range.
E3: Turn the power off and on twice, and
try again. If the problem still cannot be
solved, contact your dealer.
E4: Replace the main fuse. If the problem
continues to persist, please contact your
dealer.
E5: Check if the synchronizer is connected.
06
Loading...