Regency GFI55 User Manual

1

1

/16"

(26mm)

203/8" (517mm)

1

/16" (610mm)

24

Gas Inbuilt

GFI55 Greenfi re Pellet Insert

10"

(253mm)

13"

(329mm)

FACEPLATE DIMENSIONS

Regular Faceplate

(A) Height 30" (761mm)

1

7

/4"

(183mm)

(B) Width 39-15/16" (1014mm)

Oversize Faceplate

GFI55 Wood Pellet Insert

Pellet Stoves & Inserts

3

30

/16"

(766mm)

225/16"

(567mm)

1

3

/8" (35mm)

15

/16"

22

(582mm)

(A) Height 33" (838mm)

(B) Width 45-15/16" (1167mm)

B

A

3

21

/16"

(538mm)

2315/16" (609mm)

March 2008 Product Specifi cations Book 7

GFI55 Wood Pellet Insert

Gas Inbuilt

CLEARANCES TO COMBUSTIBLES

The fi replace insert is certifi ed to be installed into a masonry fi replace only
and/or zero clearance wood burning factory built fi replace where allowed
by local codes. This model includes a surround faceplate and a pedestal.
When installing this unit, ensure that the pedestal is removed from the
inside of the hopper and installed on the bottom of the unit.

From the body of the heater to the:
Side Wall 8" (203mm) minimum
Facing on Masonry Fireplace: 8" (203mm) minimum
8” (203mm) mantle: 8" (203mm) minimum

Pellet Stoves & Inserts

FIREPLACE SPECIFICATIONS

Your fi replace opening requires the following minimum sizes:

Height 55 lbs hopper (standard)
42 lbs hopper (adjusted)

Width 26" (660mm)

Depth 15" (381mm)

EXHAUST AND FRESH AIR INTAKE LOCATION

EXHAUST:

Base of unit to center of fl ue 9-1/16" (229mm)

Side of unit to center of fl ue 6-1/8" (156mm)

Center of unit to center of fl ue 5-3/4" (146mm)

FRESH AIR INTAKE:

Base of unit to center of intake 3-7/16" (87mm)

22.75" (578mm)

19.5" (495mm)

OUTSIDE FRESH AIR CONNECTION

Outside fresh air is mandatory when installing this unit in airtight
homes and mobile homes.

A Fresh-air intake is strongly recommended for all installations.

Failure to install intake air may result in improper combustion as well as
the unit smoking during power failures.

When connecting to an outside fresh air source, do not use plastic or
combustible pipe. A 2” minimum (51 mm) ID (inside diameter) steel,
aluminum or copper pipe should be used. It is recommended, when you
are installing a fresh air system, to keep the number of bends in the pipe
to a minimum.

Outside

Wall

2" ID

(51 mm)

Optional

Elbow

MASONRY FIREPLACE

INSERT INSTALLATION

Rain Cap

Fresh-air intake

Steel Plate or Flashing

Side of unit to center of intake 10-7/8" (277mm)

Center of unit to center of intake 1" (25mm)

INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENTING
MANUFACTURER.

3

5

/4"

(146mm)

7

/16"

3

(87mm)

7

/8"

10

(277mm)

1"

(25mm)

1

/8"

6

(156mm)

8

1

/16"

9

(229mm)

Clean-out tee

If holes already exist

fresh-air intake can

be taken through the

back of the fireplace

or through the ash

dump.

Damper Removed
or Fastened Open

Mantel (8" deep)

Min. 8" from
top of stove

Min. 6"

Floor

Protection

Masonry Fireplace

Combustible Floor

March 2008 Product Specifi cations Book