Regency F2100M, S2100M User Manual

Freestanding Woodstoves
Medium Freestanding Woodstove with optional Gold Legs.
Owners &
Installation Manual
Tested by:
908-288
Medium Freestanding Step Stove with Pedestal Base.
FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
MODELS: F1100S F2100M F3100L S2100M S3100L
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
01/13/03
Thank-you for purchasing a
REGENCY FIREPLACE PRODUCT.
The pride of workmanship that goes into each of our products will give you years of trouble-free enjoyment. Should you have any questions about your product that are not covered in this manual, please contact the REGENCY DEALER in your area.
Keep those REGENCY FIRES burning.
SAFETY NOTE: If this woodstove is not properly installed, a house fire may result. For your safety, follow the installation instructions, contact local building or fire officials about restrictions and installation inspection requirements in your area.
Modular Parts
2
Regency Freestanding Woodstove
TABLE OF CONTENTS
THE REGENCY FREESTANDING STOVE
SAFETY LABEL
Small Freestanding Stove F1100S ..................................... 4
Medium Freestanding Stove F2100M ................................. 5
Large Freestanding Stove F3100L ..................................... 6
Medium Freestanding Step Stove S2100M ........................ 7
Large Freestanding Step Stove S3100L ............................. 8
INSTALLATION
Residential Installation ....................................................... 9
Room Air.............................................................................. 9
Modular Installation Options ............................................... 9
Minimum Clearance to Combustibles.............................. 10
Residential "C" Vent Single Wall ....................................... 10
Residential Close Clearance ........................................... 10
Mobile Home Close Clearance ........................................ 10
Minimum Alcove Clearances ............................................ 1 1
Floor Protection ................................................................. 1 1
Stove Assembly Prior to Installation ................................. 12
Airmate Assembly ............................................................. 12
Rear Heat Deflector Assembly .......................................... 12
Side Shield Adjustment for the S2100 & S3100 ............... 1 2
Pedestal Assembly ........................................................... 12
Leg and Bottom Shield Assembly .................................... 13
Chimney & Connector Installation .................................... 1 3
Flue Height Table .............................................................. 14
Recommended Height for Woodstove Flue ..................... 1 4
Mobile Home Installation .................................................. 14
Listed Components for Mobile Home Installation
- U.S. Installations ...................................................... 1 5
- Canadian Installations............................................. 15
Brick Flue Baffle & Secondary Air Tube Installation
- Large Stove F3100L & S3100L................................ 15
- Medium Stove F2100M/S2100 ................................. 16
- Small Stove F1100S ................................................ 16
Brick Installation ................................................................ 17
Door Handle ...................................................................... 17
Glass Installation .............................................................. 17
Optional Accessories
- Pedestal Ash Drawer Kit .......................................... 1 7
- Bottom Shield Ashdrawer Kit ................................... 17
- Blower/Fan ............................................................... 1 8
- Blower/Fan Wiring Diagram .................................... 18
OPERATING INSTRUCTIONS
Operating Instructions....................................................... 19
Draft Control ...................................................................... 19
First Fire............................................................................. 19
Fan Operation .................................................................... 19
Ash Disposal ..................................................................... 20
- Ash Drawer Operating Guidelines ........................... 20
Safety Guidelines .............................................................. 2 0
MAINTENANCE
Maintenance ...................................................................... 20
Creosote............................................................................ 21
- Ways to Prevent & Keep Units Free of Creosote..... 21
Maintenance of Gold Doors .............................................. 21
Latch Adjustment ............................................................... 21
Door Gasket ...................................................................... 21
Glass Maintenance ........................................................... 21
- Glass Replacement ................................................. 21
Parts List - F1100, F2100, F3100 ..................................... 22
Parts List - S2100, S3100 ................................................. 23
Parts List - Pedestal, Bottom Shield and Legs ................ 24
Parts List - Firebrick .......................................................... 25
WARRANTY
Warranty............................................................................. 27
Regency Freestanding Woodstove
3
A
D
BACKWALL
SIDEWALL
B
E
G
G
I
BACKWALL
SIDEWALL
SIDEWALL
HJ
F
ADJACENT WALL
SIDEWALL
C
100
SAFETY LABEL
This is a copy of the label that accompanies each Regency Small Freestanding Woodstove (F1100S). It is located in the upper right corner
LISTED SPACE HEATER, SOLID FUEL TYPE, ALSO SUITABLE FOR MOBILE HOME INSTALLATION
MODEL: REGENCY SMALL FREESTANDING STOVE - F1100S TESTED TO: CSA B366.2 / ULC S627 / UL 1482 REPORT NO.6621 (MAY 1993)
INSTALL AND USE ONLY IN ACCORDANCE WITH THE MANUFACTURER'S INSTALLATION AND OPERATING INSTRUCTIONS. CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA. USE 150 MM (6 IN.) DIAMETER MINIMUM 24 MSG BLACK OR 26 MSG BLUED STEEL CONNECTOR WITH LISTED FACTORY-BUILT CHIMNEY SUITABLE FOR USE WITH SOLID FUELS OR MASONRY CHIMNEY. SEE LOCAL BUILDING CODE AND MANUFACTURER'S INSTRUCTIONS FOR PRECAUTIONS REQUIRED
F1100S WITH
AIRMATE SHIELD
F1100S WITHOUT AIRMATE SHIELD
MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS
F1100S WITH AIRMATE SHIELD F1100S WITHOUT AIRMATE SHIELD
MEASURE FLUE FROM HEATER CENTER-LINE
RESIDENTIAL INSTALLATION USING
SIDEWALL A 330 mm / 13 in D 635 mm / 25 in BACKWALL B 280 mm / 11 in E 445 mm / 17.5in CORNER C 205 mm / 8 in F 510 mm / 20 in
SIDEWALL A 280 mm / 11 in D 585 mm / 23 in BACKWALL B 150 mm / 6 in E 320 mm / 12.5in CORNER C 150 mm / 6 in F 460 mm / 18 in
SIDEWALL A 230 mm / 9 in D 535 mm / 21 in BACKWALL B 125 mm / 5 in E 290 mm / 11.5in CORNER C 75 mm / 3 in F 380 mm / 15 in
SIDEWALL G 280 mm / 11 in I 585 mm / 23 in BACKWALL H 180 mm / 7 in J 345 mm / 13.5in
MINIMUM ALCOVE CEILING HEIGHT: 2.15 M / 7 FT MAXIMUM ALCOVE DEPTH 915 MM / 36 IN. MINIMUM CLEARANCES FOR HORIZONTAL CONNECTOR TO CEILING: 455 MM / 18" THE SPACE BENEATH THE HEATER MUST NOT BE OBSTRUCTED. OPERATE ONLY WITH FIREBRICKS IN PLACE.
FOR USE WITH SOLID WOOD FUEL ONLY. USE OF OTHER FUELS MAY DAMAGE HEATER AND CREATE A HAZARDOUS CONDITION. DO NOT OBSTRUCT COMBUSTION AIR OPENINGS. OPERATE ONLY WITH FIREBRICKS IN PLACE. OPERATE ONLY WITH DOOR CLOSED - OPEN FEED DOOR TO FEED FIRE ONLY. DO NOT USE GRATE OR ELEVATE FIRE. BUILD WOOD FIRE DIRECTLY ON HEARTH. DO NOT OVERFIRE - IF HEATER OR CHIMNEY CONNECTOR GLOWS YOU ARE OVERFIRING. INSPECT AND CLEAN CHIMNEY AND CONNECTOR FREQUENTLY. UNDER CERTAIN CONDITIONS OF USE CREOSOTE BUILDUP MAY OCCUR RAPIDLY. KEEP FURNISHINGS AND OTHER COMBUSTIBLE MATERIAL AWAY FROM HEATER. REPLACE GLASS ONLY WITH NEOCERAM GLASS. COMBUSTIBLE FLOOR MUST BE PROTECTED BY NON-COMBUSTIBLE MATERIAL EXTENDING BENEATH THE HEATER AND TO THE FRONT AND SIDES AS INDICATED OR TO THE NEAREST PERMITTED COMBUSTIBLE MATERIAL. OPTIONAL COMPONENT: FAN, ELECTRICAL RATING: VOLTS 115, 60 HZ, 2 AMPS
COMPONENTS REQUIRED FOR MOBILE HOME INSTALLATION: OUTSIDE AIR KIT AND ONE OF THE FOLLOWING DOUBLE WALL CONNECTOR IN CANADA: LISTED SECURITY MODEL DP, OR OLIVER MACLEOD PRO-VENT PV DOUBLE WALLED CONNECTOR WITH LISTED CHIMNEY SYSTEM: SECURITY MODEL S2100, ICC EXCEL 2100 . IN USA: LISTED DOUBLE WALL CONNECTORS SECURITY MODEL DP, SELKIRK MODEL DS, OLIVER MACLEOD PRO VENT PV, SIMPSON DURA VENT MODEL DVL, GSW SUPER PIPE 6, METAL-FAB DOUBLE WALL. CONNECTED TO ONE OF THE FOLLOWING COMPATIBLE CHIMNEY SYSTEMS SECURITY MODEL S2100 OR MODEL ASHT, SELKIRK MODEL SSII, OLIVER MACLEOD PRO JET 3103, SIMPSON DURA PLUS, GSW MODEL SC OR METAL­FAB TEMP/GUARD, AMERI-TEC HS, ICC EXCEL 2100 . USE CHIMNEY COMPONENTS AS SPECIFIED IN INSTALLATION INSTRUCTIONS.
SINGLE WALL CONNECTOR
INSTALLATION USING LISTED DOUBLE WALL
CONNECTOR - MOBILE HOME
INSTALLATION USING LISTED DOUBLE WALL
CONNECTOR - RESIDENTIAL CLOSE CLEARANCE
INSTALLATION USING LISTED DOUBLE WALL
CONNECTOR - ALCOVE
FOR PASSING A CHIMNEY THROUGH A COMBUSTIBLE WALL OR CEILING. DO NOT PASS CHIMNEY CONNECTOR THROUGH COMBUSTIBLE WALL OR CEILING. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
of the back of the stove. We have printed a copy of the contents here for your review.
DO NOT REMOVE THIS LABEL
100
MEASURE FLUE FROM HEATER CENTER-LINE
RESIDENTIAL INSTALLATION USING
SIDEWALL A 380 mm /15 in D 685 mm / 27 in BACKWALL B 265 mm / 10.5in E 430 mm / 17 in CORNER C 280 mm / 11 in F 585 mm / 23 in
SIDEWALL A 330 mm / 13 in D 635 mm / 25 in BACKWALL B 125 mm / 5 in E 290 mm / 11.5in CORNER C 230 mm / 9 in F 535 mm / 21 in
SIDEWALL A 345 mm / 13.5in D 650 mm / 25.5in BACKWALL B 125 mm / 5 in E 290 mm / 11.5in CORNER C 125 mm / 5 in F 430 mm / 17 in
SIDEWALL G 330 mm / 13 in I 635 mm / 25 in BACKWALL H 125 mm / 5 in J 290 mm / 11.5in
SINGLE WALL CONNECTOR
INSTALLATION USING LISTED DOUBLE WALL
CONNECTOR - MOBILE HOME
INSTALLATION USING LISTED DOUBLE WALL
CONNECTOR - RESIDENTIAL CLOSE CLEARANCE
INSTALLATION USING LISTED DOUBLE WALL
CONNECTOR - ALCOVE
NOTE: Regency units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.
M
FLOOR
PROTECTION*
K 405 mm / 16 in L 150 mm / 6 in M 150 mm / 6in
* In Canada, floor protection must extend 18" to the front and 8" to each side of the stove.
BACK
SIDE
K
FRONT
L
SIDE
JAN FEB MAR APR MAY JUN JUL AUG SEPT OCT NOV DEC
MANUFACTURED BY: FIREPLACE PRODUCTS INTERNATIONAL LTD.
UNITED STATES ENVIRONMENTAL
PROTECTION AGENCY
CERTIFIED TO COMPLY WITH JULY 1990,
PARTICULATE EMISSION STANDARDS.
CAUTION
6988 VENTURE ST. DELTA, BC V4G 1H4
MADE IN CANADA
2003
2002
HOT WHILE IN OPERATION DO NOT TOUCH. KEEP CHILDREN,
CLOTHING AND FURNITURE AW A Y. CONT ACT MAY CAUSE
4
SKIN BURNS. READ NAMEPLATE AND INSTRUCTIONS.
908-281 01/03
Regency Freestanding Woodstove
WD
DA TE OF MANUFACTURE
2001
SAFETY LABEL
HOT WHILE IN OPERATION DO NOT TOUCH. KEEP CHILDREN,
CLOTHING AND FURNITURE AW AY . CONTACT MAY CAUSE
SKIN BURNS. READ NAMEPLATE AND INSTRUCTIONS.
DO NOT REMOVE THIS LABEL
101
CERTIFIED TO COMPLY WITH JULY 1990,
PARTICULATE EMISSION STANDARDS.
UNITED STATES ENVIRONMENTAL
PROTECTION AGENCY
MADE IN CANADA
JAN FEB MAR APR MAY JUN JUL AUG SEPT OCT NOV DEC
CAUTION
DA TE OF MANUFACTURE
WD
908-282
rev. 01/03
LISTED SPACE HEATER, SOLID FUEL TYPE, ALSO SUITABLE FOR MOBILE HOME INSTALLATION
MODEL: REGENCY MEDIUM FREESTANDING STOVE - F2100M TESTED TO: CSA B366.2 / ULC S627 / UL 1482 REPORT NO.6622 (FEB.1993)
MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS
F2100M WITH AIRMATE SHIELD F2100M WITHOUT AIRMATE SHIELD
RESIDENTIAL INSTALLATION USING
SINGLE WALL CONNECTOR
MEASURE FLUE FROM HEATER CENTER-LINE
RESIDENTIAL INSTALLATION USING
SINGLE WALL CONNECTOR SIDEWALL A 430 mm / 17 in D 735mm / 29in BACKWALL B 280 mm / 11 in E 445mm / 17.5in CORNER C 230 mm / 9 i n F 53 5 m m / 2 1 in
INSTALLATION USING LISTED DOUBLE WALL
CONNECTOR - MOBILE HOME SIDEWALL A 460 mm / 18 in D 775 mm / 30.5 in BACKWALL B 215 mm / 8.5in E 395 mm / 15.5in CORNER C 215 mm / 8.5in F 535 mm / 21 in
INSTALLATION USING LISTED DOUBLE WALL
CONNECTOR - RESIDENTIAL CLOSE CLEARANCE SIDEWALL A 355 mm / 14 in D 675 mm / 26.5 in BACKWALL B 180 mm / 7 in E 355 mm / 14 in CORNER C 215 mm / 8.5in F 535 mm / 21 in
INSTALLATION USING LISTED DOUBLE WALL
CONNECTOR - ALCOVE
SIDEWALL A 3 55 mm / 14 in D 6 60 mm / 26 in BACKWALL B 255 mm / 10 in E 420 mm / 16.5 in CORNER C 190 mm / 7.5 in F 510 mm / 20 in
INSTALLATION USING LISTED DOUBLE WALL
CONNECTOR - MOBILE HOME SIDEWALL A 405 mm / 16 in D 725 mm / 28.5in BACKWALL B 215 mm / 8.5in E 395 mm / 15.5in CORNER C 190 mm / 7.5in F 510 mm / 20 in
SIDEWALL A 255 mm / 1 0 in D 550 mm / 22.5 in BACKWALL B 115 mm / 4.5 in E 290 mm / 11.5 in CORNER C 150 mm / 6 in F 44 5 mm / 17.5 in
INSTALLATION USING LISTED DOUBLE WALL
CONNECTOR - RESIDENTIAL CLOSE CLEARANCE
INSTALLATION USING LISTED DOUBLE WALL
CONNECTOR - ALCOVE SIDEWALL G 355 mm / 14 in I 675 mm / 26.5in BACKWALL H 180 mm / 7 in J 355 mm / 14 in
MINIMUM ALCOVE CEILING HEIGHT: 2.15 M / 7 FT MAXIMUM ALCOVE DEPTH 915 MM / 36 IN. MINIMUM CLEARANCES FOR HORIZONTAL CONNECTOR TO CEILING: 455 MM / 18" THE SPACE BENEATH THE HEATER MUST NOT BE OBSTRUCTED. OPERATE ONLY WITH FIREBRICKS IN PLACE.
FLOOR
PROTECTION*
F2100M WITHOUT AIRMATE SHIELD
F2100M WITH
AIRMATE SHIELD
INSTALL AND USE ONLY IN ACCORDANCE WITH THE MANUFACTURER'S INSTALLATION AND OPERATING INSTRUCTIONS. CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA. USE 150 MM (6 IN.) DIAMETER MINIMUM 24 MSG BLACK OR 26 MSG BLUED STEEL CONNECTOR WITH LISTED FACTORY-BUILT CHIMNEY SUITABLE FOR USE WITH SOLID FUELS OR MASONRY CHIMNEY. SEE LOCAL BUILDING CODE AND MANUFACTURER'S INSTRUCTIONS FOR PRECAUTIONS REQUIRED FOR PASSING A CHIMNEY THROUGH A COMBUSTIBLE WALL OR CEILING. DO NOT PASS CHIMNEY CONNECTOR THROUGH COMBUSTIBLE WALL OR CEILING. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
FRONT
BACK
L
K
M
SIDE
SIDE
K 405 mm / 16 in L 150 mm / 6 in M 150 mm / 6 in
FOR USE WITH SOLID WOOD FUEL ONLY. USE OF OTHER FUELS MAY DAMAGE HEATER AND CREATE A HAZARDOUS CONDITION. DO NOT OBSTRUCT COMBUSTION AIR OPENINGS. OPERATE ONLY WITH FIREBRICKS IN PLACE. OPERATE ONLY WITH DOOR CLOSED - OPEN FEED DOOR TO FEED FIRE ONLY. DO NOT USE GRATE OR ELEVATE FIRE. BUILD WOOD FIRE DIRECTLY ON HEARTH. DO NOT OVERFIRE - IF HEATER OR CHIMNEY CONNECTOR GLOWS YOU ARE OVERFIRING. INSPECT AND CLEAN CHIMNEY AND CONNECTOR FREQUENTLY. UNDER CERTAIN CONDITIONS OF USE CREOSOTE BUILDUP MAY OCCUR RAPIDLY. KEEP FURNISHINGS AND OTHER COMBUSTIBLE MATERIAL AWAY FROM HEATER. REPLACE GLASS ONLY WITH NEOCERAM GLASS. COMBUSTIBLE FLOOR MUST BE PROTECTED BY NON-COMBUSTIBLE MATERIAL EXTENDING BENEATH THE HEATER AND TO THE FRONT AND SIDES AS INDICATED OR TO THE NEAREST PERMITTED COMBUSTIBLE MATERIAL. OPTIONAL COMPONENT: FAN, ELECTRICAL RATING: VOLTS 115, 60 HZ, 2 AMPS
COMPONENTS REQUIRED FOR MOBILE HOME INSTALLATION: OUTSIDE AIR KIT AND ONE OF THE FOLLOWING DOUBLE WALL CONNECTOR IN CANADA: LISTED SECURITY MODEL DP, OR OLIVER MACLEOD PRO-VENT PV DOUBLE WALLED CONNECTOR WITH LISTED CHIMNEY SYSTEM: SECURITY MODEL S2100, ICC EXCEL 2100. IN USA: LISTED DOUBLE WALL CONNECTORS SECURITY MODEL DP, SELKIRK MODEL DS, OLIVER MACLEOD PRO VENT PV, SIMPSON DURA VENT MODEL DVL, GSW SUPER PIPE 6, METAL-FAB DOUBLE WALL. CONNECTED TO ONE OF THE FOLLOWING COMPATIBLE CHIMNEY SYSTEMS SECURITY MODEL S2100 OR MODEL ASHT, SELKIRK MODEL SSII, OLIVER MACLEOD PRO JET 3103, SIMPSON DURA PLUS, GSW MODEL SC OR METAL­FAB TEMP/GUARD, AMERI-TEC HS, ICC EXCEL 2100 . USE CHIMNEY COMPONENTS AS SPECIFIED IN INSTALLATION INSTRUCTIONS.
MEASURE FLUE FROM HEATER CENTER-LINE
MANUFACTURED BY: FIREPLACE PRODUCTS INTERNATIONAL LTD.
6988 VENTURE ST. DELTA, BC V4G 1H4
SIDEWALL G 255 mm / 10 in I 570 mm / 22.5in BACKWALL H 115 mm / 4.5in J 290 mm / 11.5 in
2001 20032002
* In Canada, floor protection must extend 18" to the front and 8" to each side of the stove.
This is a copy of the label that accompanies each Regency Medium Freestanding Wood-
corner of the back of the stove. We have printed a copy of the contents here for your review.
stove (F2100M). It is located in the upper right
NOTE: Regency units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.
BACKWALL
B
E
A
SIDEWALL
D
BACKWALL
HJ
SIDEWALL
G
I
ADJACENT WALL
SIDEWALL
F
SIDEWALL
G
C
Regency Freestanding Woodstove
5
FRONT
BACK
L
K
M
SIDE
SIDE
SAFETY LABEL
This is a copy of the label that accompanies each Regency Large Freestanding Woodstove (F3100L). It is located in the upper right corner
of the back of the stove. We have printed a copy of the contents here for your review.
NOTE: Regency units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.
LISTED SPACE HEATER, SOLID FUEL TYPE, SUITABLE FOR MOBILE HOME INSTALLATION
MODEL: REGENCY LARGE FREESTANDING STOVE - F3100L
TESTED TO: CSA B366.2 / ULC S627 / UL 1482 REPORT NO.6623 (MAY 93)
INSTALL AND USE ONLY IN ACCORDANCE WITH THE MANUFACTURER'S INSTALLATION AND OPERAT­ING INSTRUCTIONS. CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA. USE 150 MM (6 IN.) DIAMETER MINIMUM 24 MSG BLACK OR 26 MSG BLUED STEEL CONNECTOR WITH LISTED FACTORY-BUILT CHIMNEY SUITABLE FOR USE WITH SOLID FUELS OR MASONRY CHIMNEY. SEE LOCAL BUILDING CODE AND MANUFACTURER'S INSTRUCTIONS FOR PRECAUTIONS REQUIRED
F3100L WITH
AIRMATE SHIELD
F3100L WITHOUT AIRMATE SHIELD
MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS
F3100L WITH AIRMATE SHIELD
MEASURE FLUE FROM HEATER CENTER-LINE
RESIDENTIAL INSTALLATION USING
SIDEWALL A 460 mm / 18 in D 810 mm / 32 in BACKWALL B 305 mm / 12 in E 470 mm / 18.5in CORNER C 215 mm / 8.5in F 560 mm / 22 in
SIDEWALL A 460 mm / 18 in D 810 mm / 32 in BACKWALL B 240 mm / 9.5in E 405 mm / 16 in CORNER C 255 mm / 10 in F 595 mm / 23.5in
SIDEWALL A 405 mm / 16 in D 760 mm / 30 in BACKWALL B 240 mm / 9.5in E 405 mm / 16 in CORNER C 215 mm / 8.5in F 560 mm / 22 in
SIDEWALL G 405 mm / 16 in I 760 mm / 30 in BACKWALL H 240 mm / 9.5in J 405 mm / 16 in
MINIMUM CLEARANCE BETWEEN HORIZONTAL CHIMNEY CONNECTOR AND COMBUSTIBLE MATERIALS - 460 MM (18 IN.). CLEARANCE MAY BE REDUCED BY THE USE OF LISTED PIPE SHIELDS, WALL PROTECTORS OR OTHER MEANS APPROVED BY LOCAL BUILDING OR FIRE OFFICIALS. COMBUSTIBLE FLOOR MUST BE PROTECTED BY NON-COMBUSTIBLE MATERIAL EXTENDING BENEATH THE HEATER AND TO THE FRONT AND SIDES AS INDICATED OR TO THE NEAREST PERMITTED COMBUSTIBLE MATERIAL.
FOR USE WITH SOLID WOOD FUEL ONLY. USE OF OTHER FUELS MAY DAMAGE HEATER AND CREATE A HAZARDOUS CONDITION. DO NOT OBSTRUCT COMBUSTION AIR OPENINGS. OPERATE ONLY WITH FIREBRICKS IN PLACE. OPERATE ONLY WITH DOOR CLOSED - OPEN FEED DOOR TO FEED FIRE ONLY. DO NOT USE GRATE OR ELEVATE FIRE. BUILD WOOD FIRE DIRECTLY ON HEARTH. DO NOT OVERFIRE - IF HEATER OR CHIMNEY CONNECTOR GLOWS YOU ARE OVERFIRING. INSPECT AND CLEAN CHIMNEY AND CONNECTOR FREQUENTLY. UNDER CERTAIN CONDITIONS OF USE CREOSOTE BUILDUP MAY OCCUR RAPIDLY. KEEP FURNISHINGS AND OTHER COMBUSTIBLE MATERIAL AWAY FROM HEATER. REPLACE GLASS ONLY WITH NEOCERAM GLASS. OPTIONAL COMPONENT: FAN, ELECTRICAL RATING: VOLTS 115, 60 HZ, 2 AMPS
COMPONENTS REQUIRED FOR MOBILE HOME INSTALLATION: OUTSIDE AIR KIT AND ONE OF THE FOLLOWING DOUBLE WALL CONNECTOR IN CANADA: LISTED SECURITY MODEL DP, OR OLIVER MACLEOD PRO-VENT PV DOUBLE WALLED CONNECTOR WITH LISTED CHIMNEY SYSTEM: SECURITY MODEL S2100, ICC EXCEL 2100. IN USA: LISTED DOUBLE WALL CONNECTORS SECURITY MODEL DP, SELKIRK MODEL DS, OLIVER MACLEOD PRO VENT PV, SIMPSON DURA VENT MODEL DVL, GSW SUPER PIPE 6, METAL-FAB DOUBLE WALL. CONNECTED TO ONE OF THE FOLLOWING COMPATIBLE CHIMNEY SYSTEMS SECURITY MODEL S2100 OR MODEL ASHT, SELKIRK MODEL SSII, OLIVER MACLEOD PRO JET 3103, SIMPSON DURA PLUS, GSW MODEL SC OR METAL­FAB TEMP/GUARD, AMERI-TEC HS, ICC EXCEL 2100 . USE CHIMNEY COMPONENTS AS SPECIFIED IN INSTALLATION INSTRUCTIONS.
SINGLE WALL CONNECTOR
INSTALLATION USING LISTED DOUBLE WALL
CONNECTOR - MOBILE HOME
INSTALLATION USING LISTED DOUBLE WALL
CONNECTOR - RESIDENTIAL CLOSE CLEARANCE
INSTALLATION USING LISTED DOUBLE WALL
CONNECTOR - ALCOVE
FOR PASSING A CHIMNEY THROUGH A COMBUSTIBLE WALL OR CEILING. DO NOT PASS CHIMNEY CONNECTOR THROUGH COMBUSTIBLE WALL OR CEILING. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
F3100L WITHOUT AIRMATE SHIELD
MEASURE FLUE FROM HEATER CENTER-LINE
RESIDENTIAL INSTALLATION USING
SIDEWALL A 510 mm / 20 in D 860 mm / 34 in BACKWALL B 355 mm / 14 in E 520 mm / 20.5 in CORNER C 265 mm / 10.5in F 610 mm / 24 in
SIDEWALL A 510 mm / 20 in D 860 mm / 34 in BACKWALL B 305 mm / 12 in E 470 mm / 18.5in CORNER C 255 mm / 10 in F 595 mm / 23.5in
SIDEWALL A 510 mm / 20 in D 860 mm / 34 in BACKWALL B 305 mm / 12 in E 470 mm / 18.5in CORNER C 215 mm / 8.5in F 560 mm / 22 in
SINGLE WALL CONNECTOR
INSTALLATION USING LISTED DOUBLE WALL
CONNECTOR - MOBILE HOME
INSTALLATION USING LISTED DOUBLE WALL
CONNECTOR - RESIDENTIAL CLOSE CLEARANCE
ALCOVE INSTALLATION
REQUIRES AIRMATE SHIELD
DO NOT REMOVE THIS LABEL
102
BACKWALL
B
A
SIDEWALL
D
BACKWALL
HJ
SIDEWALL
G
I
ADJACENT WALL
SIDEWALL
F
FLOOR
PROTECTION* K 405 mm / 16 in L 150 mm / 6 in M 150 mm / 6 in
* In Canada, floor protection must extend 18" to the front and 8" to each side of the stove.
E
SIDEWALL
G
C
JAN FEB MAR APR MAY JUN JUL AUG SEPT OCT NOV DEC
UNITED STATES ENVIRONMENTAL
PROTECTION AGENCY
MANUFACTURED BY: FIREPLACE PRODUCTS INTERNATIONAL LTD.
CERTIFIED TO COMPLY WITH JULY 1990,
PARTICULATE EMISSION STANDARDS.
6988 VENTURE ST. DELTA, BC V4G 1H4
MADE IN CANADA
2003
2002
CAUTION
HOT WHILE IN OPERATION DO NOT TOUCH. KEEP CHILDREN,
CLOTHING AND FURNITURE AWA Y. CONTACT MAY CAUSE
SKIN BURNS. READ NAMEPLATE AND INSTRUCTIONS.
6
908-351
01/03
Regency Freestanding Woodstove
WD
DA TE OF MANUFACTURE
2001
SAFETY LABEL
This is a copy of the label that accompanies each Regency Medium Freestanding Step Woodstove (S2100M). It is located in the upper right corner
of the back of the stove. We have printed a copy of the contents here for your review.
NOTE: Regency units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.
107
LISTED SPACE HEATER, SOLID FUEL TYPE, ALSO SUITABLE FOR MOBILE HOME INSTALLATION
MODEL: REGENCY MEDIUM FREESTANDING STEP STOVE - S2100M
TESTED TO: CSA B366.2 / ULC S627 / UL 1482 REPORT NO.6622 (FEB.1993)
INSTALL AND USE ONLY IN ACCORDANCE WITH THE MANUFACTURER'S INSTALLATION AND OPERATING INSTRUCTIONS. CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA. USE 150 MM (6 IN.) DIAMETER MINIMUM 24 MSG BLACK OR 26 MSG BLUED STEEL CONNECTOR WITH LISTED FACTORY-BUILT CHIMNEY SUITABLE FOR USE WITH SOLID FUELS OR MASONRY CHIMNEY.
S2100M
S2100 MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS
MEASURE FLUE FROM HEATER CENTER-LINE
RESIDENTIAL INSTALLATION USING SINGLE WALL CONNECTOR SIDEWALL A 355 mm / 14 in D 660 mm / 2 6 in BACKWALL B 255 mm / 10 in E 420 mm / 16.5 in CORNER C 1 50 mm / 6 in F 445 m m / 17.5 in
INSTALLATION USING LISTED DOUBLE WALL CONNECTOR - MOBILE HOME SIDEWALL A 405 mm / 16 in D 725 mm / 28.5 in BACKWALL B 215 mm / 8.5 in E 395 mm / 15.5 in CORNER C 1 90 mm / 7. 5 i n F 51 0 m m / 20 i n
INSTALLATION USING LISTED DOUBLE WALL CONNECTOR ­RESIDENTIAL CLOSE CLEARANCE SIDEWALL A 255 mm / 10 in D 550 mm / 22.5 in BACKWALL B 115 mm / 4.5 in E 290 mm / 11.5 in CORNER C 1 90 mm / 7. 5 i n F 51 0 m m / 20 i n
INSTALLATION USING LISTED DOUBLE WALL CONNECTOR - ALCOVE SIDEWALL G 2 55 mm / 10 in I 570 mm / 22.5 in BACKWALL H 115 mm / 4.5 in J 290 mm / 11.5 in
FOR USE WITH SOLID WOOD FUEL ONLY. USE OF OTHER FUELS MAY DAMAGE HEATER AND CREATE A HAZARDOUS CONDITION. DO NOT OBSTRUCT COMBUSTION AIR OPENINGS. OPERATE ONLY WITH FIREBRICKS IN PLACE. OPERATE ONLY WITH DOOR CLOSED - OPEN FEED DOOR TO FEED FIRE ONLY. DO NOT USE GRATE OR ELEVATE FIRE. BUILD WOOD FIRE DIRECTLY ON HEARTH. DO NOT OVERFIRE - IF HEATER OR CHIMNEY CONNECTOR GLOWS YOU ARE OVERFIRING. INSPECT AND CLEAN CHIMNEY AND CONNECTOR FREQUENTLY. UNDER CERTAIN CONDITIONS OF USE CREOSOTE BUILDUP MAY OCCUR RAPIDLY. KEEP FURNISHINGS AND OTHER COMBUSTIBLE MATERIAL AWAY FROM HEATER. REPLACE GLASS ONLY WITH NEOCERAM GLASS. COMBUSTIBLE FLOOR MUST BE PROTECTED BY NON-COMBUSTIBLE MATERIAL EXTENDING BENEATH THE HEATER AND TO THE FRONT AND SIDES AS INDICATED OR TO THE NEAREST PERMITTED COMBUSTIBLE MATERIAL. OPTIONAL COMPONENT: FAN, ELECTRICAL RATING: VOLTS 115, 60 HZ, 2 AMPS
COMPONENTS REQUIRED FOR MOBILE HOME INSTALLATION: OUTSIDE AIR KIT AND ONE OF THE FOLLOWING DOUBLE WALL CONNECTOR IN CANADA: LISTED SECURITY MODEL DP, OR OLIVER MACLEOD PRO-VENT PV DOUBLE WALLED CONNECTOR WITH LISTED CHIMNEY SYSTEM: SECURITY MODEL S2100, ICC EXCEL 2100. IN USA: LISTED DOUBLE WALL CONNECTORS SECURITY MODEL DP, SELKIRK MODEL DS, OLIVER MACLEOD PRO VENT PV, SIMPSON DURA VENT MODEL DVL, GSW SUPER PIPE 6, METAL-FAB DOUBLE WALL. CONNECTED TO ONE OF THE FOLLOWING COMPATIBLE CHIMNEY SYSTEMS SECURITY MODEL S2100 OR MODEL ASHT, SELKIRK MODEL SSII, OLIVER MACLEOD PRO JET 3103, SIMPSON DURA PLUS, GSW MODEL SC OR METAL-FAB TEMP/ GUARD, AMERI-TEC HS, ICC EXCEL 2100 . USE CHIMNEY COMPONENTS AS SPECIFIED IN INSTALLATION INSTRUCTIONS.
SEE LOCAL BUILDING CODE AND MANUFACTURER'S INSTRUCTIONS FOR PRECAUTIONS REQUIRED FOR PASSING A CHIMNEY THROUGH A COMBUSTIBLE WALL OR CEILING. DO NOT PASS CHIMNEY CONNECTOR THROUGH COMBUSTIBLE WALL OR CEILING. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
BACKWALL
B
A
SIDEWALL
D
BACKWALL
HJ
SIDEWALL
G
I
ADJACENT WALL
C
SIDEWALL
F
DO NOT REMOVE THIS LABEL
107
E
SIDEWALL
G
FLOOR PROTECTION*
M
BACK
SIDE
K
FRONT
MINIMUM ALCOVE CEILING HEIGHT:
MAXIMUM ALCOVE DEPTH:
MINIMUM CLEARANCES FOR HORIZONTAL CONNECTOR TO CEILING:
THE SPACE BENEATH THE HEATER MUST NOT BE OBSTRUCTED. OPERATE ONLY WITH FIREBRICKS IN PLACE.
K 405 mm / 16 in L 150 mm / 6 i n
L
SIDE
M 150 mm / 6 in
* In Canada, floor protec­tion must extend 18" to the front and 8" to each side of the stove.
2.15 M / 7 FT
915 MM / 36 IN.
455 MM / 18"
JAN FEB MAR APR MAY JUN JUL AUG SEPT OCT NOV DEC
Note: Hard copy - exact size 8" x 5-3/4". On disc, print at 65% to achieve actual size.
Everything printed black on grey except what is highlighted in yellow is printed red on gray.
UNITED STATES ENVIRONMENTAL
PROTECTION AGENCY
HOT WHILE IN OPERATION DO NOT TOUCH. KEEP CHILDREN,
Regency Freestanding Woodstove
MANUFACTURED BY: FIREPLACE PRODUCTS INTERNATIONAL LTD.
6988 VENTURE ST. DELTA, BC V4G 1H4
MADE IN CANADA
CERTIFIED TO COMPLY WITH JULY 1990,
PARTICULATE EMISSION STANDARDS.
CAUTION
CLOTHING AND FURNITURE AWA Y. CONTACT MAY CAUSE
SKIN BURNS. READ NAMEPLATE AND INSTRUCTIONS.
WD
908-733
rev. 01/03
2004
2003
DATE OF MANUFACTURE
2002
system . No other changes.
Feb. 14/02: Updated serial number
7
SAFETY LABEL
This is a copy of the label that accompanies each Regency Large Freestanding Step Wood­stove (S3100L). It is located in the upper right
corner of the back of the stove. We have printed a copy of the contents here for your review.
NOTE: Regency units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.
8
Regency Freestanding Woodstove
INSTALLATION
RESIDENTIAL
INSTALLATION
1) Read all instructions before installing your
Regency Stove. Install and use only in accordance with these installation and operating instructions. Be aware that local Codes and Regulations may override some items in this manual. Check with your local inspector.
2) Select a position for your Regency Stove. Consult the minimum clearance chart for your model and set the stove in place. For close clearance installation use listed dou­ble wall connector systems (see page 15).
3) To insure vertical alignment, suspend a plumb bob from the ceiling over the exact center of your stove flue and mark a spot on the ceiling to indicate the center of the chimney.
4) Check that the area above the ceiling is clear for cutting. Re-confirm the clearance from the stove to combustibles to insure that they are within the prescribed limits.
5) Install chimney according to chimney man­ufacturers instructions. The performance of your woodstove is governed to a very large part by the chimney system. Too short a chimney can cause difficult start-up, dirty glass, backsmoking when door is open, and even reduced heat output. Too tall a chim­ney may prompt excessive draft which can result in very short burn times and exces­sive heat output. The use of an inexpensive flue pipe damper may be helpful in reducing excessive draft.
CAUTION: The chimney should be the same size as the flue outlet on the stove. The
chimney must be listed as suitable for use with solid fuels. For other types of chim­neys check with your local building code officials. Do not confuse a chimney with a type “B” Venting System used for gas appliances as suitable for a wood burning appliance. For Mobile Home installations refer to that section on page 14.
6) Mark the location of the pedestal base or legs on the floor, then move the stove aside and mark the position of the floor protector.
7) The floor protector must be of non-combus­tible material and must extend 16" in front of the door opening and 6" to the sides and rear of the unit. Some areas may require a larger size floor protector. See your local inspector. For outside air installation refer to Mobile Home installation instructions on page 14.
NOTE: In Canada, floor protection must
extend 18" to the front and 8" to each side of the stove.
8) When the floor protection is complete, po-
sition the stove with the flue collar centered under the installed chimney.
9) In seismically active areas, Regency rec­ommends that your unit is secured to the floor by using the bolt down holes inside the pedestal (the same ones used in Mobile Home installations).
10)For residential installations using "C" Vent (single wall) the chimney connector must be at least 24 gauge steel. Do not use galvanized pipe. For Mobile Home installa­tion refer to the Mobile Home installation instructions on page 14.
11)Do not connect this unit to a chimney serv­ing another appliance unless approved by
your local building authority.
12)A chimney connector cannot pass through an attic or roof space, closet or similar concealed space, or a floor, ceiling, wall or partition of combustible construction. In Canada, if passage through a wall, or par­tition of combustible construction is de­sired, the installation shall conform to CAN/ CSA-B365, Installation Code for Solid-Fuel­Burning Appliances and Equipment.
13)Your Regency Woodstove is not to be connected to any air distribution duct.
Emissions from burning wood or gas could contain chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
ROOM AIR
IMPORTANT
For installation using room air for combustion, remove knockout from the pedestal, and/or from the bottom if using a heat shield.
Mobile home installations require the use of outside air.
On pedestal units there are two locations where outside air may be adapted to the unit. If using the bottom of the pedestal, do not remove knockout from the rear of the pedestal. Only remove rear knockout if outside air will be brought in from the rear.
On leg units outside air can only be brought in from the bottom of the heat shield.
Note: Once the knockout is removed
there are two tabs remaining. Bend both tabs out for ease of installa­tion when attaching outside air.
MODULAR INSTALLATION OPTIONS
The following items are required when assembling your Regency Stove. F1100, F2100, and F3100 units - the Rear Heat Deflector is supplied with the stove, but if you choose not to use it you must use the Airmate instead.
Modular Part
F1100, F2100 and
F3100 only: Airmate OR
Rear Heat Deflector
(all units)
Pedestal OR
Legs
Clearances are different. See the chart on pages 10 and 11. Generally you can get closer clearances with the airmate than with the rear heat deflector.
Convection heat with Airmate vs. Radiant Heat with Rear Heat Deflector. The airmate pushes heat forward and into the room, the rear heat deflector deflects the heat upward. See installation instructions on pages 11 and 12.
There are no performance differences with either the pedestal or legs. It is primarily a personal preference. Legs can be either painted steel, painted cast, or gold plated cast.
Leg installation requires the bottom shield. See installation instructions on page 13.
OPTIONS: These can be installed at time of installation or added later:
Modular Option
Blower/Fan
Ash Drawer Kit
Regency Freestanding Woodstove
Adding the blower will increase the area heated by the stove, it can move warm air beyond the room where the stove is installed. Installation instructions on page 18.
Adding the Ash Drawer Kit makes cleaning ashes out of the stove easier and cleaner. Installation instructions on page
17.
Things to consider when choosing options:
Things to consider when choosing options
9
Loading...
+ 19 hidden pages