Raymarine E70111, E70110, T203, E70113, T220 Installation And Operation Instructions Manual

...

T200

Installation and operation instructions

English

Chapter1:Importantinformation

Warning:Productinstallationand operation

Thisproductmustbeinstalledandoperatedin accordancewiththeinstructionsprovided.Failure todosocouldresultinpersonalinjury ,damageto yourvesseland/orpoorproductperformance.

Warning:Potentialignitionsource

ThisproductisNOTapprovedforusein hazardous/ammableatmospheres.DoNOTinstall inahazardous/ammableatmosphere(suchasin anengineroomornearfueltanks).

Warning:Productgrounding

Beforeapplyingpowertothisproduct,ensureithas beencorrectlygrounded,inaccordancewiththe instructionsinthisguide.

Warning:Switchoffpowersupply

Ensurethevessel’spowersupplyisswitchedOFF beforestartingtoinstallthisproduct.DoNOT connectordisconnectequipmentwiththepower switchedon,unlessinstructedinthisdocument.

Warning:Ensuresafenavigation

Thisproductisintendedonlyasanaidtonavigation andmustneverbeusedinpreferencetosound navigationaljudgment.Onlyofcialgovernment chartsandnoticestomarinerscontainallthe currentinformationneededforsafenavigation,and thecaptainisresponsiblefortheirprudentuse.Itis theuser’sresponsibilitytouseofcialgovernment charts,noticestomariners,cautionandproper navigationalskillwhenoperatingthisoranyother Raymarineproduct.

Warning:Maintainapermanent watch

Alwaysmaintainapermanentwatch,thiswillallow youtorespondtosituationsastheydevelop. Failuretomaintainapermanentwatchputs yourself,yourvesselandothersatseriousriskof harm.

Caution:Powersupplyprotection

Wheninstallingthisproductensurethepower sourceisadequatelyprotectedbymeansofa suitably-ratedfuseorautomaticcircuitbreaker.

Caution:Serviceandmaintenance

Thisproductcontainsnouserserviceable components.Pleasereferallmaintenance andrepairtoauthorizedRaymarinedealers. Unauthorizedrepairmayaffectyourwarranty .

Cleaningthethermalcamera

Thecamerahousingandlenswillrequireoccasionalcleaning. Raymarinesuggeststhatyoucleanthelenswhenimagequality degradationisnoticedorexcessivecontaminantbuildupisseen. Cleantheinterfacebetweentheyokeandbaseoftentoprevent accumulationofdebrisorsaltdeposits.

Whencleaningthisproduct:

•DoNOTwipethelenswindowwithadrycloth,asthiscould scratchthecoating.

•DoNOTuseabrasive,oracidorammoniabasedproducts.

•DoNOTpressurewash.

Particularcareshouldbetakenwhencleaningthelenswindow, thishasaprotectiveanti-reectivecoatingwhichmaybe damagedbyimpropercleaning.

1.Switchoffthepowertotheunit.

2.Cleanthecamerabodywithaclean,softcottoncloth.Y ou

canmoistentheclothanduseamilddetergentifrequired.

3.Cleanthecameralens.

•Rinsethelenswithfreshwatertoremovealldirtparticles andsaltdeposits,andallowtodrynaturally.

•Ifanyspotsorsmearsremain,verygentlywipethelens windowwithacleanmicrobreclothorsoftcottoncloth.

•Ifnecessary,useisopropylalcohol(IPA)oramilddetergent toremoveanyremainingspotsormarks.

Wateringress

Wateringressdisclaimer Althoughthewaterproofratingcapacityofthisproductmeets

theIPX6standard,waterintrusionandsubsequentequipment failuremayoccuriftheproductissubjectedtocommercial high-pressurewashing.Raymarinewillnotwarrantproducts subjectedtohigh-pressurewashing.

Disclaimer

Raymarinedoesnotwarrantthatthisproductiserror-freeorthat itiscompatiblewithproductsmanufacturedbyanypersonor entityotherthanRaymarine.

Raymarineisnotresponsiblefordamagesorinjuriescausedby youruseorinabilitytousetheproduct,bytheinteractionofthe productwithproductsmanufacturedbyothers,orbyerrorsin informationutilizedbytheproductsuppliedbythirdparties.

EMCinstallationguidelines

Raymarineequipmentandaccessoriesconformtothe appropriateElectromagneticCompatibility(EMC)regulations, tominimizeelectromagneticinterferencebetweenequipment andminimizetheeffectsuchinterferencecouldhaveonthe performanceofyoursystem

CorrectinstallationisrequiredtoensurethatEMCperformance isnotcompromised.

ForoptimumEMCperformancewerecommendthatwherever possible:

•Raymarineequipmentandcablesconnectedtoitare:

–Atleast1m(3ft)fromanyequipmenttransmittingor

cablescarryingradiosignalse.g.VHFradios,cablesand antennas.InthecaseofSSBradios,thedistanceshould beincreasedto7ft(2m).

–Morethan2m(7ft)fromthepathofaradarbeam.A

radarbeamcannormallybeassumedtospread20degrees aboveandbelowtheradiatingelement.

•Theproductissuppliedfromaseparatebatteryfromthatused forenginestart.Thisisimportanttopreventerraticbehavior anddatalosswhichcanoccuriftheenginestartdoesnot haveaseparatebattery .

Importantinformation

•Raymarinespeciedcablesareused.

•Cablesarenotcutorextended,unlessdoingsoisdetailedin theinstallationmanual.

Note:Whereconstraintsontheinstallationprevent anyoftheaboverecommendations,alwaysensurethe

maximumpossibleseparationbetweendifferentitemsof electricalequipment,toprovidethebestconditionsforEMC performancethroughouttheinstallation

Chapter2:Handbookandproductinformation

Chaptercontents

•2.1Handbookinformationonpage10

•2.2Productinformationonpage10

Handbookandproductinformation

2.1Handbookinformation

ThishandbookdescribestheinstallationofRaymarineT200 Seriesxedmountthermalcamerasaspartofamarine electronicssystem.

Thishandbookincludesinformationtohelpyou:

•planyourthermalimagingsystemandensureyouhaveallthe necessaryequipment,

•installandconnectthethermalcameraasapartofyour systemofRaymarineelectronics,

•obtainsupportifrequired.

Handbooks

DescriptionPartnumber

T200SeriesInstallationandOperations Handbook

81349

T200SeriesMountingT emplate

87190

2.2Productinformation

TheT200seriesxedmountthermalcamerasconsistofasealed cameraballassemblyandaremovableoutercover.Theouter coverisnotintendedtoprovidesealing.Thecameraprovides analogvideooutputthroughastandardF-typeconnectionand receivespowerfromitsPoweroverEthernet(PoE)interface.

D12865-1

ThefollowingvariantsoftheT200seriesxedmountthermal cameraareavailable:

PartnumberDescription

E7011 1

T200–Thermalcamera320x240(9Hz)NTSC

E70110

T203–Thermalcamera320x240(30Hz)NTSC

E70113

T220–Thermalcamera320x240(9Hz)P AL

E70112

T223–Thermalcamera320x240(25Hz)P AL

E70121

T250–Thermalcamera640x480(9Hz)NTSC

E70120

T253–Thermalcamera640x480(30Hz)NTSC

E70123

T270–Thermalcamera640x480(9Hz)P AL

E70122

T273–Thermalcamera640x480(25Hz)P AL

Note:TheT200Seriesarexedmountcameraswiththe panandtiltanglessetduringinstallation.Panandtiltcannot bechangedremotely.

T200

Chapter3:Planningtheinstallation

Chaptercontents

•3.1Thermalcameracontrollersanddisplaysonpage12

•3.2Installationchecklistonpage12

•3.3Typicalsystemsonpage13

•3.4Partssuppliedonpage14

•3.5T oolsrequiredonpage15

Planningtheinstallation

3.1Thermalcameracontrollersand

displays

Atypicalthermalcamerasystemcomprisesofathermalcamera, acontrollerandadisplay .Thedisplayandthecontrollermaybe separateorintegrated.

D12838-1

1 2

1.Thermalcamera.

2.RaymarineMultifunctiondisplay—Integrateddisplayand

controller.

3.JoystickControlUnit(JCU)—Controlleronly.

4.LaptoporPC—Controlleronly .

5.Videomonitor—Displayonly.

Additionalequipment

Youmayhaveadditionalequipmentaspartofyourthermal camerasystem:

•Multiplemultifunctiondisplaysandcontrollers.

•SeaT alk

networkswitch–Usedtocreateanetworkof

compatibleRaymarineequipment.

Compatiblemultifunctiondisplays

ThefollowingRaymarinemultifunctiondisplaysarecompatible withyourthermalcamera.

•cSeries(PoweroverEthernet(PoE)injectorrequired)

•eSeries(PoweroverEthernet(PoE)injectorrequired)

•gSSeries

3.2Installationchecklist

Installationincludesthefollowingactivities:

InstallationT ask

1Planyoursystem.

Obtainallrequiredequipmentandtools.

Siteallequipment.

4Routeallcables.

Drillcableandmountingholes.

6Makeallconnectionsintoequipment.

Secureallequipmentinplace.

8Poweronandtestthesystem.

Schematicdiagram

Aschematicdiagramisanessentialpartofplanningany installation.Itisalsousefulforanyfutureadditionsor maintenanceofthesystem.Thediagramshouldinclude:

•Locationofallcomponents.

•Connectors,cabletypes,routesandlengths.

T200

3.3Typicalsystems

Examplec/eSeriessystem

D12839-1

1Thermalcamera.

c/eSeriesmultifunctiondisplay(Integrateddisplayand controller).

PoweroverEthernet(PoE)injector.

RayNettoSeaT alk

cable.

Videocable.

ExamplegSSeriessystem

3 4

D12840-1

1Thermalcamera.

gSSeriesmultifunctiondisplay(Integrateddisplayand controller).

3Ethernetcoupler .

RayNettoSeaT alk

cable.

Videocable.

Note:WhenconnecteddirectlytoagSSeriesmultifunction displaythethermalcameraissuppliedwithpowerover ethernetfromthedisplay .

ExampleSystemwithJCU

D12841-1

c/eSeriesmultifunctiondisplay(Integrateddisplayand controller).

2Thermalcamera.

3Videoinputcable.

4Networkswitch.

JCU(Optionalcontroller).

PoweroverEthernet(PoE)injector(Requiredtosupply powertotheJCU).

PoweroverEthernet(PoE)injector(Requiredtosupply powertothethermalcamera).

8RayNetcable.

RayNettoSeaT alk

cable.

ExamplesystemwithJCUanddisplay

D12842-1

VideoDisplay(Displayonly).

2Thermalcamera.

3Videoinputcable.

JCU(RequiredController).

PoweroverEthernet(PoE)injector(Requiredtosupply powertotheJCU).

PoweroverEthernet(PoE)injector(Requiredtosupply powertothethermalcamera).

Networkswitch.

RayNettoSeaT alk

cable.

ExamplesystemwithPCcontrolleranddisplay

D12843-1

7 5

VideoDisplay(Displayonly).

2Thermalcamera.

3Videoinputcable.

Planningtheinstallation

4Networkswitch.

RayNettoSeaT alk

cable.

PoweroverEthernet(PoE)injector(Requiredtosupply powertothethermalcamera).

Laptop(Controlleronly).

3.4Partssupplied

x6 x6 x6

2 3

D12844-1

ItemDescriptionQuantity

1Thermalcamera.1

2Ethernetcoupler .1

PoweroverEthernet(PoE)Injector.

Mountingkit,consistingof:

•M8nylocknut

•acornnut

•stud

•washer

O-ring.

Top-downxings.

Documentationpack.1

Groundingstrapsecuringnut.

9Videoconnectors:

•FemaletofemaleF-typeconnector

•FemaleF-typetoMaleRCAadaptor

•FemaleF-typetoBNCconnector

10Zipties.3

1m(3.28ft.)RayNettoSeaT alk

cable.

7.7m(25ft.)Ethernetcable.

7.7m(25ft.)Coaxialvideocable.

Unpackthecameraunitcarefullytopreventdamage.Savethe cartonandpackingincasetheunithastobereturnedforservice.

Additionalitemsrequired

Tocompletetheinstallationyouwillalsoneedtoobtainthe followingitems:

T200

•Chassisgroundstrap.

•Compatibledisplay/controllerhardware.

•Cablesforvideoconnections.

•PowercableforPoEinjector(ifusingthePoEinjector).

•Threadlockingcompound(e.g.Loctite242orequivalent), requiredforallmetal-to-metalthreadedconnections.

•Marinegradesealingtape(e.g.3MScotch-Seal2229or equivalent).

3.5Toolsrequired

Thefollowingtoolsarerequiredforinstallation.

D1233 3-1

ItemDescription

1.Drill.

10mm(7/16inch)spanner.

6.4mmdrillbit(forbottomdown installation).

Jigsaw(onlyrequiredforJCU installation).

Pozi-drivescrewdriver(onlyrequired forJCUinstallation).

6.Thread-lock.

Planningtheinstallation

Chapter4:Cablesandconnections

Chaptercontents

•4.1Generalcablingguidanceonpage18

•4.2Connectionsoverviewonpage18

•4.3Chassisgroundconnectiononpage19

•4.4Externalorinternalconnectionsonpage19

•4.5Networkandpowerconnectiononpage20

•4.6Videoconnectiononpage21

•4.7PoEconnectiononpage21

•4.8PCconnectiononpage23

Cablesandconnections

4.1Generalcablingguidance

Cabletypesandlength

Itisimportanttousecablesoftheappropriatetypeandlength

•Unlessotherwisestateduseonlystandardcablesofthe correcttype,suppliedbyRaymarine.

•Ensurethatanynon-Raymarinecablesareofthecorrect qualityandgauge.Forexample,longerpowercablerunsmay requirelargerwiregaugestominimizevoltagedropalongthe run.

Routingcables

Cablesmustberoutedcorrectly,tomaximizeperformanceand prolongcablelife.

•DoNOTbendcablesexcessively .Whereverpossible,ensure aminimumbenddiameterof200mm(8in)/minimumbend radiusof100mm(4in).

100mm (4in)

200mm (8in)

•Protectallcablesfromphysicaldamageandexposuretoheat. Usetrunkingorconduitwherepossible.DoNOTruncables throughbilgesordoorways,orclosetomovingorhotobjects.

•Securecablesinplaceusingtie-wrapsorlacingtwine.Coil anyextracableandtieitoutoftheway .

•Whereacablepassesthroughanexposedbulkheador deckhead,useasuitablewatertightfeed-through.

•DoNOTruncablesneartoenginesoruorescentlights.

Alwaysroutedatacablesasfarawayaspossiblefrom:

•otherequipmentandcables,

•highcurrentcarryingacanddcpowerlines,

•antennae.

Strainrelief

Ensureadequatestrainreliefisprovided.Protectconnectors fromstrainandensuretheywillnotpulloutunderextremesea conditions.

Cableshielding

Ensurethatalldatacablesareproperlyshieldedthatthe cableshieldingisintact(e.g.hasn’tbeenscrapedoffbybeing squeezedthroughatightarea).

Warning:Productgrounding

Beforeapplyingpowertothisproduct,ensureithas beencorrectlygrounded,inaccordancewiththe instructionsinthisguide.

4.2Connectionsoverview

D12845-1

1.Chassisground

2.Analogvideoconnection—IRoutput.

3.Ethernet–T oRaymarinenetworkswitch,multifunction display,orJCU.

Connectioncarepoints:

•Thecabletailsshouldberoutedtoadryareaofthevesselfor

connection.Alternativelyyoumustensurethatallconnections aremadewatertight.

T200

4.3Chassisgroundconnection

Thechassisgroundstudshouldbeconnectedtothevessel groundpoint.

D12846-1

Thenut(supplied)shouldbeusedtosecureagroundstrap(not supplied)tothebaseofthethermalcamera.Aringterminal typicallysizedfor#6orM3sizedstudandgauge14togauge16 wireshouldbeusedforthestrap.

Note:Ensurethatthegroundstrapdoesnotinterferewith mountingthecamera.

4.4Externalorinternalconnections

Thecableconnectionscanbemadeexternallyorinternally .

External

Assupplied,thecameracabletailsextendthroughthebase andareconnectedexternally:

D12847-1

Internal

Optionallyyoucanmakethecableconnectionsinternally.

D12848-1

Tomakeinternalconnections,bringthecabletailsupthroughthe baseandusethesuppliedethernetcouplerandvideoconnector tomaketheconnectionsinternally.Theethernetcouplercanbe xedtothecameraballassemblyusingthezipties(supplied).

Cablesandconnections

4.5Networkandpowerconnection

Thethermalcameraissuppliedpowerbyandcontrolledusing theethernetnetworkconnection.

CameratomultifunctiondisplaywithPoE

FormultifunctiondisplaysthatsupportPoE,thefollowing suppliedequipmentisrequired:

•RayNettoRJ45SeaT alk

cable.

•Ethernetcoupler.

CameratomultifunctiondisplaywithoutPoE

FormultifunctiondisplaysthatdonotsupportPoE,thefollowing suppliedequipmentisrequired:

•PoEinjector.

•RayNettoRJ45SeaT alk

cable.

•Ethernetcoupler

Cameratoanetworkswitch

ToconnectthethermalcameratoaRaymarinenetworkswitch, thefollowingsuppliedequipmentisrequired:

•7.6m(25ft)Ethernetcable.

•Ethernetcoupler

•PoEinjector.

•RayNettoRJ45SeaT alk

cable.

PoweroverEthernet(PoE)injector

APoEinjectorisrequiredwhenconnectingthethermalcamera toaRaymarinenetworkswitchortoamultifunctiondisplaythat doesnotsupportPoE.AnadditionalPoEinjectorisrequired whenconnectingaJCU.

JoystickControlUnit(JCU)

ToconnectaJCUtheethernetcable(suppliedwiththeJCU), PoEinjectorandaRayNettoSeaT alk

networkcableare required.TheJCUissuppliedwitha7.6m(25ft)ethernetcable forthisconnection.Ifyourequireadifferentlengthcontactyour dealerforsuitablecables.

Note:ThePoEinjectormustbemountedinadryarea.

Networkcables

RayNettoRayNetcables

CablePartnumber

400mm(1.3ft)RayNettoRayNet cable(female)

A80161

2m(6.56ft)RayNettoRayNetcable (female)

A62361

5m(16.4ft)RayNettoRayNetcable (female)

A80005

10m(32.8ft)RayNettoRayNet cable(female)

A62362

20m(65.6ft)RayNettoRayNet cable(female)

A80006

50mm(1.97in)RayNettoRayNet cable(male)

A80162

RayNetright-angledcouplerA80262

RayNetcablepuller5-packR70014

RayNettoRJ45SeaTalk

adaptercables

CablePartnumber

1m(3.28ft)RayNettoRJ45 SeaTalk

cable

A62360

3m(9.84ft)RayNettoRJ45 SeaTalk

cable

A80151

CablePartnumber

10m(32.8ft)RayNettoRJ45 SeaTalk

cable

A80159

400mm(1.3ft)RayNettoRJ45 SeaTalk

(female)cable

A80160

T200

4.6Videoconnection

Videocablesandconnectorsarerequiredtoconnecttheanalog videoconnectiontoasuitabledisplay.

Note:Thevideosignalisanalogonlyandisnotavailable overethernet.

Videocables

Ifyourequirevideocablesorconnectorsotherthanthose suppliedwiththeproductpleasecontactyourlocalauthorized Raymarinedealer.

RaymarinerecommendstheuseofaBNCterminatedRG59 75ohm(orbetter)coaxialcable.

4.7PoEconnection

APoEinjectorisrequiredwhenconnectingthethermalcamera toanetworkswitchoramultifunctiondisplaythatdoesnot supportPoE.AnadditionalPoEinjectorisrequiredwhen connectingaJCU.

ThePoEinjectorrequiresa12V/24Vdcpowersupply.

D12849 -1

12V/24VdcpowersupplyconnectiontoPoEinjector.(Power cableNOTsupplied;refertoPoEpowerconnectionforsuitable cables.)

SeaTalk

connection(tonetworkswitchormultifunction

display).

3PoEInjector.

Ethernetconnection(tothermalcameraorJCU).

PoEpowerconnection

ThePoEinjectorrequiresadedicatedpowercablefordirect connectiontoa12V/24Vpowersupply .

Theunitisintendedforuseondc“negative”or“oating”ground powersystems.

Raymarinerecommendsthatallpowerconnectionsaremade viaadistributionpanel.Allequipmentmustbeeither:

•poweredfromacircuitbreakerorswitch,with5Acircuit protection,or

•poweredfroma5Aslowblowin-linefuseconnectedtothe REDpositivewireofthepowercable.

Theunitdoesnothaveapowerswitch.Theunitispowered whenthepowercableisconnectedtothevessel'spowersupply.

Note:Theunitshouldbemountedsothatthepowercable canbeeasilyremovedifnecessary.Iftheunitisplacedina difculttoreachlocation,Raymarinerecommendsinstalling anon/offswitchonthepowerconnectionatapointthatis easilyaccessible.

Recommendedpowercablesizes

Cablelength

Wiresize

FeetMetres

AWG

103142.1

154.6142.1

206123.3

257.6123.3

309105.3

Note:

•Cablelengthisthedistancebetweenthepowersource andtheunit.

•Thesewiresizesgiveatotaldropofabout0.5Vbetween thepowersourceandtheunit,achievingaminimumvoltage attheunitof10.5Vwithafullyatbatteryat1 1V .

Cablesandconnections

+ 32 hidden pages

Raymarine E70111, E70110, T203, E70113, T220 Installation And Operation Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual