Rainbow Electronics UC864 User Manual

UC864-E/G Product Description
UC864-E/G 80281ST10034a Rev. 1 - 08/08/2008
PRODUCT
PART NUMBER
UC864
-E
UC864
-G
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
APPLICABILITY TABLE
4990250031 4990250030
Contents
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
1 Overview ........................................................................................................................... 6
2 General Product Description ........................................................................................... 8
2.1 Dimensions ...........................................................................................................................8
2.2 Weight ................................................................................................................................. 10
2.3 Environmental requirements ............................................................................................. 10
2.3.1
Temperature range ......................................................................................................................... 10
2.3.2
Vibration Test (non functional) ........................................................................................................ 10
2.3.3
RoHS compliance ........................................................................................................................... 11
2.4 Operating Frequency .......................................................................................................... 11
2.5 Transmitter output power .................................................................................................. 11
2.6 Reference sensitivity .......................................................................................................... 12
2.7 Antennas ............................................................................................................................. 12
2.7.1
GSM/WCDMA Antenna .................................................................................................................. 12
2.7.2
GPS Antenna (only for UC864-G) .................................................................................................. 13
2.7.3
UC864-E/G Antenna connectors .................................................................................................... 13
2.7.3.1 GSM/WCDMA Applications ........................................................................................................ 13
2.7.3.2 GPS Applications (only for UC864-G) ........................................................................................ 13
2.8 GPS features (only for UC864-G) ....................................................................................... 13
2.8.1
GPS Sensitivity* .............................................................................................................................. 14
2.8.2
GPS Consumption* ......................................................................................................................... 14
2.8.3
GPS Driving .................................................................................................................................... 14
2.8.4
GPS NMEA ..................................................................................................................................... 15
2.8.5
NMEA sentences ............................................................................................................................ 15
2.9 Supply voltage .................................................................................................................... 15
2.10 WCDMA/GSM Power consumption .................................................................................... 16
2.11 Embodied Battery charger ................................................................................................. 16
2.12 User Interface ...................................................................................................................... 17
2.12.1 Speech Coding ............................................................................................................................... 17
2.12.2 SIM Reader ..................................................................................................................................... 17
2.12.3 SMS ................................................................................................................................................ 17
2.12.4 Real Time Clock and Alarm ............................................................................................................ 17
2.12.5 Data/fax Transmission .................................................................................................................... 18
2.12.6 Local security management ............................................................................................................ 18
2.12.7 Call control ...................................................................................................................................... 18
2.12.8 Phonebook ...................................................................................................................................... 18
2.12.9 Characters management ................................................................................................................ 18
2.12.10
2.12.11
2.12.12
2.12.13
2.12.14
2.12.15
SIM related functions .................................................................................................................. 18
Call status indication ................................................................................................................... 18
Automatic answer (Voice, Data or FAX) ..................................................................................... 19
Supplementary services (SS) ..................................................................................................... 19
Acoustic signaling ....................................................................................................................... 19
Buzzer output .............................................................................................................................. 19
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
2.12.16
RF Transmission Monitor............................................................................................................ 20
2.13 Logic level specifications .................................................................................................. 20
2.13.1 Reset signal .................................................................................................................................... 20
2.14 Audio levels specifications ................................................................................................ 21
2.15 Converters ........................................................................................................................... 22
2.15.1 ADC Converter ............................................................................................................................... 22
2.15.2 DAC Converter ............................................................................................................................... 22
2.16 Mounting the UC864-E/G on your board ........................................................................... 23
2.16.1 UC864-G ......................................................................................................................................... 23
2.16.2 UC864-E ......................................................................................................................................... 24
2.17 Packing system (TBD) ........................................................................................................ 25
3 Evaluation Kit ................................................................................................................. 26
4 Software Features .......................................................................................................... 27
4.1 Enhanced Easy GPRS Extension ...................................................................................... 27
4.1.1
Overview ......................................................................................................................................... 27
4.1.2
Easy GPRS definition ..................................................................................................................... 28
5 AT Commands ................................................................................................................ 29
6 Conformity Assessment Issues .................................................................................... 30
7 SAFETY RECOMMENDATIONS ..................................................................................... 32
7.1 Contact Information, Support ............................................................................................ 33
List of acronyms ................................................................................................................... 34
8 Document Change Log .................................................................................................. 36
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
DISCLAIMER
The information contained in this document is the proprietary information of Telit Communications S.p.A. and its affiliates (“TELIT”). The contents are confidential and any disclosure to persons other than the officers, employees, agents or subcontractors of the owner or licensee of this document, without the prior written consent of Telit, is strictly prohibited.
Telit makes every effort to ensure the quality of the information it makes available. Notwithstanding the foregoing, Telit does not make any warranty as to the information contained herein, and does not accept any liability for any injury, loss or damage of any kind incurred by use of or reliance upon the information.
Telit disclaims any and all responsibility for the application of the devices characterized in this document, and notes that the application of the device must comply with the safety standards of the applicable country, and where applicable, with the relevant wiring rules.
Telit reserves the right to make modifications, additions and deletions to this document due to typographical errors, inaccurate information, or improvements to programs and/or equipment at any time and without notice. Such changes will, nevertheless be incorporated into new editions of this application note.
All rights reserved. © 2008 Telit Communications S.p.A.
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
1 Overview
The Telit UC864-E/G module are small, lightweight, low power consumption and RoHS compliant devices that allow digital communication services wherever a WCDMA/HSDPA (850 ,1900 and 2100 MHz for UC864-G and only 2100 MHz for UC864-E), GSM 850, 900, DCS 1800 or PCS 1900 network is present with additional options like an integrated GPS receiver (in UC864-G only).
The UC864-E/G is a low cost connector-less best solution for medium to high quantity projects. The UC864-E/G is provided with an 80 pin Molex board to board connector and a 50 Ohm Murata RF
connector. The UC 864-G is still provided with an additional 50 Ohm Murata RF connector for GPS receiver.
The UC864-E/G module includes features like GPRS/EDGE CLASS 12, Voice, Circuit Switched Data transfer, Fax, Phonebook and SMS support, embedded TCP/IP stack and battery charging capabilities.
The UC864-E/G is specifically designed and developed by Telit for OEM usage and dedicated to portable data, voice and telemetric applications such as:
Telemetry and Telecontrol (SCADA applications)
Security systems
Automated Meter Reading (AMR)
Vending machines
POS terminals
PDAs and Mobile Computing
Phones and Payphones
Automotive and Fleet Management applications
Battery powered applications needing a battery charger
Return channel for digital broadcasting
Position reporting and tracking with integrated GPS
The UC864-E/G supports the following functionalities
EASY GPRS (AT driven embedded TCP/IP protocol stack)
EASY SCAN (full GSM frequency scanning)
From the interface point of view, the UC864-E/G provides the following:
USB2.0 for AT commands
- Baud rate up to 12 Mbps
Full RS232 UART, CMOS level (ASC0) interface for AT commands:
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
- Fixed baud rate up to 230 Kbps
SIM card interface, 1.8 / 3 volts with auto-detection and hot insertion
22 x GPIO ports (max)
3 x A/D converters
1 x D/A converter
1 x buzzer output
1 x single led supply output
In order to meet the competitive OEM and vertical market stringent requirements, Telit supports its customers with a dedicated Support Policy with:
Telit Evaluation Kit EVK2 to help you develop your application;
A Website with all updated information available;
An high level specialist technical support to assist you in your development;
For more updated information concerning product Roadmap, availability, technical characteristics, commercial and other issues, please check on the Telit website www.telit.com > Products (UMTS/HSDPA) > UC864 Family.
NOTE: Some of the performances of the Telit modules depend on SW version installed on the module itself. The Telit modules SW group is continuously working in order to add new features and improve the overall performances. The Telit modules are easily upgradeable by the developer using the Telit Flash Programmer. Furthermore, all the Telit modules have the conformity assessment against FCC.
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
2 General Product Description
2.1 Dimensions
Dimensions UC864-E UC864-G
Length(mm) 36.2 45
Width(mm) 30 30
Thickness(mm)
4.8 4.8
UC864-E drawing
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
UC864-G drawing
2.2 Weight
Weight
UC684-E 10 gr.
UC864-G 12.8 gr.
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
2.3 Environmental requirements
The Telit UC864-E/G module is compliant with the applicable 3gpp reference documentation TS
25.101 Release 2004-03.
2.3.1 Temperature range
UC864-E/G Note
The module is functional in all
-20 ~ +55°C
Operating temperature
-30 ~ +80°C
Temperature in not
functional conditions
* Functional: the module is able to make and receive voice calls, data calls, SMS and make data traffic..
-40 ~ +85°C
the temperature range, and it fully meets the
ETSI specifications.
The module is functional in all
the temperature range. Temperatures
outside the range –20°C ÷ +55°C,
might slightly deviate from ETSI specifications.
2.3.2 Vibration Test (non functional)
10 ~12Hz ASD = 1.92m 2 /s 3
12 ~ 150Hz –3dB/oct
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 10 of 36
Note
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
2.3.3 RoHS compliance
As a part of Telit corporate policy regarding environmental protection, the UC864-E/G comply with the RoHS (Restriction of Hazardous Substances) directive of the European Union (EU Directive 2002/95/EG).
2.4 Operating Frequency
The operating frequencies in WCDMA/HSDPA, GSM850, EGSM900, DCS, PCS modes are conform to the WCDMA and 3gpp specifications.
Mode Freq. TX (MHz) Freq. RX (MHz) Channels (ARFC) TX - RX offset
WCDMA-850 826.4-846.6 871.4-891.6 WCDMA-1900 1852.4-1907.6 1932.4-1987.6 WCDMA-2100 1922.4-1977.6 2112.4-2167.6
GSM-850 E-GSM-900
DCS-1800 1710.2 - 1784.8 1805.2 - 1879.8 512 – 885 95 MHz PCS-1900 1850.2 - 1909.8 1930.2 - 1989.8 512 - 810 80 MHz
824.2-848.8 869.2-893.8 128-251 45 MHz
890.0 - 914.8 935.0 - 959.8 0 – 124 45 MHz
880.2 - 889.8 925.2 - 934.8 975 - 1023 45 MHz
Tx : 4132-4233 Rx : 4357-4458 Tx : 9262-9538 Rx : 9662-9938 Tx : 9612-9888 Rx : 10562-10838
45MHz 80MHz 190MHz
UC864-G Only UC864-G Only
2.5 Transmitter output power
WCDMA850/1900/2100
The Telit UC864-E/G transceiver module in WCDMA-850/1900/2100 (2100 only for UC864-E) operating mode are class 3 in accordance with the specifications which determine the nominal 0.25W peak RF power (+24dBm) on 50 Ohm.
GSM850/900(GSM/GPRS mode)
The Telit UC864-E/G transceiver module in GSM850/900 operating mode are class 4 in accordance with the specifications which determine the nominal 2W peak RF power (+33dBm) on 50 Ohm.
GSM850/900(EGPRS mode)
The Telit UC864-E/G transceiver module in GSM850/900 operating mode are class E2 in accordance with the specifications which determine the nominal 0.5W peak RF power (+27dBm) on 50 Ohm.
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 11 of 36
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
DCS1800/PCS1900(GSM/GPRS mode)
The Telit UC864-E/G transceiver modules in DCS1800/PCS1900 operating mode are class 1 in accordance with the specifications which determine the nominal 1W peak RF power (+30dBm) on 50 Ohm.
DCS1800/PCS1900(EGPRS mode)
The Telit UC864-E/G transceiver modules in DCS1800/PCS1900 operating mode are class E2 in accordance with the specifications which determine the nominal 0.4W peak RF power (+26dBm) on 50 Ohm.
2.6 Reference sensitivity
WCDMA850/1900/2100
The sensitivity of the Telit UC864-E/G module according to the specifications for the class 3 portable terminals WCDMA850/1900/2100 are –108.2 dBm typical in normal operating conditions.
GSM850/900
The sensitivity of the Telit UC864-E/G module according to the specifications for the class 4 GSM850/900 portable terminals are –107 dBm typical in normal operating conditions.
DCS1800/PCS1900
The sensitivity of the Telit UC864-E/G module according to the specifications for the class 1 portable terminals DCS1800/PCS1900 are –106 dBm typical in normal operating conditions.
2.7 Antennas
2.7.1 GSM/WCDMA Antenna
The antenna that the customer chooses to use should fulfill the following requirements:
Frequency range
Bandwidth
For further information please refer to the UC864 Hardware User Guide.
Depending by frequency band(s) provided by the network operator, the customer shall use the most suitable antenna for that/those band(s) 70 MHz in GSM850, 80 MHz in GSM900, 170 MHz in DCS & 140 MHz PCS 70 MHZ in WCDMA850,140 MHz in WCDMA1900 & 250 MHz in WCDMA2100 band
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 12 of 36
Frequency range
Bandwidth
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
2.7.2 GPS Antenna (only for UC864-G)
The active GPS antenna should fulfill the following requirements:
1575.42 MHz(GPS L1 band) +/- 2 MHz
The supply voltage to the active GPS antenna is provided by the UC864-G. For further information please refer to the UC864 Hardware User Guide.
2.7.3 UC864-E/G Antenna connectors
2.7.3.1 GSM/WCDMA Applications
The UC864-E/G module is equipped with a 50 Ohm RF connector from Murata, GSC type P/N MM9329-2700B. The suitable counterpart is Murata MXTK92 Type or MXTK88 Type.
2.7.3.2 GPS Applications (only for UC864-G)
The UC864-G module is equipped with an additional 50 Ohm RF connector from Murata, GSC type P/N MM9329-2700B. The suitable counterpart is Murata MXTK92 Type or MXTK88 Type.
2.8 GPS features (only for UC864-G)
The UC864-G includes the Qualcomm gpsOne functionality to support standalone GPS that supports real-time location in urban area and wherever a high sensitivity acquisition is needed. This enables a wide variety of location-based services and applications, including points of interest, personal navigation, and friend finder. In standalone mode, the handset demodulates the data directly from the GPS satellites and it requires no server interaction and works out of network coverage.
As main features of such GPS receiver, we can mention:
• Simultaneous GPS and Voice/Data
• High sensitivity for indoor reception, up to -157dBm (with active antenna)
• Extremely fast TTFF’s at low signal levels
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 13 of 36
Time to first fix
Hot start
Warm start
Cold start
Sens
itivity
Tracking
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
• Supports 12-Channel GPS L1 1575.42 MHz
• Accuracy < 3m (CEP68 : 68% Circular Error Probable )
• GPS NMEA 0183 output format
• Date WGS-84
• Dedicated GPS AT commands
• Low power consumption
2.8.1 GPS Sensitivity*
Autonomous < 1s Autonomous < 32s Autonomous < 40s
Up to -157 dBm
* NOTE: Performance will vary depending on environment, antenna type, signal conditions, satellite geometry, and handset implementation.
2.8.2 GPS Consumption*
The typical current consumption of the GPS part of the UC864-G module is:
UC864-G
Mode Average(mA) Mode description
IDLE mode with GPS ON full power mode
AT+CFUN=1
AT+CFUN=4
WCDMA 145 GSM 104 WCDMA 104 GSM 104
Stand by mode; no call in progress; GPS ON
* Except external active GPS antenna
2.8.3 GPS Driving
The GPS functions are driven from the Base Band processor trough a dedicated AT command set available in a separate specification.
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 14 of 36
Nominal operating voltage
Operating voltage range
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
2.8.4 GPS NMEA
The GPS data stream (NMEA 0183 format) is also available on the pin-out in USB data format.
2.8.5 NMEA sentences
The following GPS sentences are available:
GGA - Global positioning system fix data (provides 3D location and accuracy data) VTG – Course over ground and ground speed GSA - GPS DOP and active satellites RMC - Recommended Minimum Specific GPS Data GLL - Geographic Latitude and Longitude
2.9 Supply voltage
The external power supply must be connected to VBATT signal and must fulfill the following requirements:
3.8 V
3.51 V – 4.2 V
NOTE: Operating voltage range must never be exceeded; care must be taken in order to fulfill min/max voltage requirements.
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 15 of 36
Stand
by current (
WCDMA
Idle)
Stand
by current (GSM Idle)
Operating current in
WCDMA
voice channel
Operating current in
GSM vo
ice channel
Operating current in
WCDMA data channel
Operating current in HSDPA channel
Operating current in GPRS Class 12
Operating curren
t in EGPRS Class 12
Battery charger input pin
Battery pins
Battery charger input voltage min
Battery charger input voltage typ
Battery charger input voltage max
Battery charger input
current max
Battery type
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
2.10 WCDMA/GSM Power consumption
The typical current consumption of the Telit UC864-E/G is:
Power off current (typical)
< 26 µA; < 23.2mA (<5.3mA using command AT+CFUN=5) < 15.0mA (<3.6mA using command AT+CFUN=5) < 690 mA @ worst network conditions < 317 mA @ worst network conditions < 680 mA @ worst network conditions < 730 mA @ worst network conditions < 790 mA @ worst network conditions < 560 mA @ worst network conditions
2.11 Embodied Battery charger
The battery charger is suited for 3.7V Li-Ion rechargeable battery (suggested capacity 500-1000mAH). The Charger needs only a CURRENT LIMITED power source input and charges the battery directly through VBATT connector pins.
CHARGE VBATT, GND
5.0 V
5.5 V
7.0 V
NOTE: If embodied battery charger is used, then a LOW ESR capacitor of at least 100µF must be mounted in parallel to VBATT pin. NOTE: when power is supplied to the CHARGE pin, a battery must always be connected to the VBATT pin of the UC864-E/G.
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 16 of 36
400mA Li-Ion rechargeable
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
2.12 User Interface
The user interface is managed by AT commands specified on the ITU-T V.250, 3gpp 27.007 and
27.005 specifications.
2.12.1 Speech Coding
The UC864-E/G voice codec supports the following rates:
WCDMA o Adaptive Multi Rate
GSM
o Half Rate o Full rate o Enhanced Full Rate o Adaptive Multi Rate
2.12.2 SIM Reader
The UC864-E/G supports R5 and R99 3gpp TS 31.114 - USIM 1.8V and 3V ONLY with an external SIM connector. For 5V SIM operation an external level translator can be added.
2.12.3 SMS
The UC864-E/G supports the following SMS types:
Mobile Terminated (MT) class 0 – 3 with signaling of new incoming SMS, SIM full, SMS
read
Mobile Originated class 0 – 3 with writing, memorize in SIM and sending
Cell Broadcast compatible with CB DRX with signaling of new incoming SMS.
2.12.4 Real Time Clock and Alarm
The Telit UC864-E/G supports the Real Time Clock and Alarm functions through AT commands, furthermore an alarm output pin (GPIO6) can be configured to indicate the alarm with a hardware line output. Furthermore the Voltage Output of the RTC power supply is provided so that a backup capacitor can be added to increase the RTC autonomy.
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 17 of 36
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
2.12.5 Data/fax Transmission
The Telit UC864-E/G supports:
WCDMA/HSDPA category 8, MS Class A (Simultaneous Voice and Data)
EGPRS/GPRS CLASS 12, MS Class B
CSD up to 14.4 Kbps
Fax service, Class 1 Group 3.
2.12.6 Local security management
The local security management can be done with the lock of Universal Subscriber Identity module (USIM), and security code request at power–up.
2.12.7 Call control
The call cost control function is supported.
2.12.8 Phonebook
This function allows the storing of the telephone numbers in SIM memory. The capability depends on SIM version and embedded memory.
2.12.9 Characters management
The Telit UC864-E/G supports the IRA characters set (International Reference Alphabet), in TEXT and PDU mode.
2.12.10 SIM related functions
Activation and deactivation of the numbers stored in phone book FDN, ADN and PINs are supported. Extension at the PIN2 for the PUK2 insertion capability for lock condition is supported.
2.12.11 Call status indication
The call status indication by AT commands is supported.
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 18 of 36
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
2.12.12 Automatic answer (Voice, Data or FAX)
After a specified number of rings, the module will automatically answer with a beep. The user can set the number of rings by means of the command ATS0=<n>.
2.12.13 Supplementary services (SS)
The following supplementary services are supported:
Call Barring,
Call Forwarding,
Calling Line Identification Presentation (CLIP),
Calling Line Identification Restriction (CLIR),
Call Waiting, other party call Waiting Indication,
Call Hold, other party Hold / Retrieved Indication,
Closed User Group supplementary service (CUG),
Advice of Charge,
Unstructured SS Mobile Originated (MO)
2.12.14 Acoustic signaling
The acoustic signaling of the UC864-E/G on the selected acoustic device are the following:
Call waiting;
Ringing tone;
SMS received tone;
Busy tone;
Power on/off tone;
Off Hook dial tone;
Congestion tone;
Connected tone;
Call dropped;
No service tone;
Alarm tone.
2.12.15 Buzzer output
The General Purpose I/O pin GPIO7 can be configured to output the BUZZER output signal, with only an external MOSFET/transistor and a diode a Buzzer can be directly driven. The ringing tone and the other signaling tones can be redirected to this Buzzer output with a specific AT command.
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 19 of 36
Signal
Function
I/O UC864
-G
pin
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
2.12.16 RF Transmission Monitor
As alternate function of the GPIO5, the UC864-E/G provides the RF transmission monitor. When the alternate function is activated, the pin of GPIO5 changes to HIGH every time the module transmits an RF signal and remains HIGH for the duration of the transmission sequence
2.13 Logic level specifications
Where not specifically stated, all the interface circuits work at 2.6V CMOS logic levels. To get more detailed information about the logic level specifications used in the Telit UC864-E/G interface circuits please consult the UC864-E/G Hardware User Guide.
2.13.1 Reset signal
RESET Phone reset I/O 54
RESET is used to reset the UC864-E/G. Whenever this signal is pulled low; the UC864-E/G is reset. When the device is reset it stops any operation and after the release of the reset it is unconditionally rebooted, without doing any detach operation from the network where it is registered to. This behavior is not like a proper shut down because any device is requested to issue a detach request on turn off. For this reason the Reset signal must not be used to normally shutting down the device, but only as an emergency exit in the rare case the device remains stuck waiting for some network response. The RESET is internally controlled on start-up to achieve always a proper power-on reset sequence, so there's no need to control this pin on start-up. It may only be used to reset a device already on that is not responding to any command.
NOTE: do not use this signal to power off the Telit UC864-E/G module. Use the ON_OFF* signal to perform this function or the AT#SHDN command.
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 20 of 36
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
2.14 Audio levels specifications
The audio of the UC864-E/G is organized into two main paths:
internal path (called also MT)
external path (called also HF)
These two paths are meant respectively for handset and headset/hands-free use. The UC864-E/G has a built in echo canceller and a noise suppressor, tuned separately for the two audio paths; for the internal path the echo canceller parameters are suited to cancel the echo generated by a handset, while for the external audio path they are suited for a hands-free use. For more information on the audio refer to the UC864 Hardware User Guide.
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 21 of 36
Min Max
Units
Min Max
Units
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
2.15 Converters
2.15.1 ADC Converter
The on board ADCs are 8-bit converter. They are able to read a voltage level in the range of 0 - 2 volts applied on the ADC pin input, store and convert it into 8 bit word.
Input Voltage range 0 2,0 Volt
AD conversion - 8 bits
Resolution - < 8 mV
Sampling rate 1 (idle) 60 (on traffic) sec
2.15.2 DAC Converter
The on board DAC is a 16 bit converter, able to generate an analogue value based a specific input in the range from 0 up to 65536. However, an external low-pass filter is necessary. See the HW User Guide for the details.
Voltage range (filtered) 0 2,6 Volt Range 0 65536 Steps
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 22 of 36
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
2.16 Mounting the UC864-E/G on your board
2.16.1 UC864-G
The position of the Molex board to board connector and the pin 1 are shown in the following picture.
NOTE: metal tabs present on UC864-G should be connected to GND
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 23 of 36
2.16.2 UC864-E
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
NOTE: metal tabs present on UC864-E should be connected to GND
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 24 of 36
2.17 Packing system
The Telit UC864-E is packaged on trays of 20 pieces each.
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 25 of 36
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
3 Evaluation Kit
In order to assist you in the development of your Telit UC864-E/G module based application, Telit can supply the EVK2 Evaluation Kit with appropriate power supply, SIM card housing, RS 232 serial port level translator, direct UART connection, Handset, Headset and Hands-free (car kit) audio, antenna. The EVK2 provides a fully functional solution for a complete data/phone application. The standard serial RS232 9 pin connector placed on the Evaluation Kit allows the connection of the
EVK2 system with a PC or other DTE.
The development of the applications utilizing the Telit UC864-E/G module must present a proper design of all the interfaces towards and from the module (e.g. power supply, audio paths, level translators), otherwise a decrease in the performances will be introduced or, in the worst case, a wrong design can even lead to an operating failure of the module. In order to assist the hardware designer in his project phase, the EVK2 board presents a series of different solutions, which will cover the most common design requirements on the market, and which can be easily integrated in the OEM design as building blocks or can be taken as starting points to develop a specific one.
Evaluation Kit
For a detailed description of the Telit Evaluation Kit refer to the documentation provided with the Telit
UC864-E/G Hardware User Guide and EVK2 User Manual.
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 26 of 36
Remote
Controller
Device
Device
(Internet)
TCP/UDP
GPRS
GPRS
IPIPIP
IP
Serial
Data
Line
on
L2
L2
V.24
V.24
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
4 Software Features
4.1 Enhanced Easy GPRS Extension
4.1.1 Overview
The Easy establish with it a raw data flow over the This feature can be seen as a way to obtain a "virtual" serial connection between the Application Software on the Internet machine involved and the controller of the Telit UC864-E/G module, regardless of all the software stacks underlying. An example of the protocol stack involved in the devices is reported:
WCDMA/
GPRS feature allows the Telit UC864-E/G user to contact a device in internet and
WCDMA/
GPRS and Internet networks.
Telit
GE864 / GC864 networks
Local Remote
Application Application
Firewall
EASY EASY TCP/UDP
Driver Board
<<<---------------------------------- Virtual Serial link ---------------------------------->>>
network interworking
L1 L1
This particular implementation allows to the devices interfacing to the Telit UC864-E/G module the use of the GPRS and Internet packet service without the need to have an internal TCP/IP stack since this function is embedded inside the module. Easy GPRS overcomes some of the known limitations of the previous implementation and implements some new features such as:
Keep the GPRS context active even after the closing of a socket, allowing the application to keep the same IP address;
Also Mobile terminated (incoming) connections can be made, now it is possible to receive incoming TCP connection requests;
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 27 of 36
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
A new internal firewall has been implemented in order to guarantee a certain level of security on internet applications.
4.1.2 Easy GPRS definition
The Easy GPRS feature provides a way to replace the need of an Internet TCP/IP stack at the terminal equipment side. The steps that will be required to obtain a virtual serial connection (that is actually a socket) to the Internet peer are:
configuring the GPRS Access
configuring the embedded TCP/IP stack behavior
defining the Internet Peer to be contacted
request the GPRS and socket connections to be opened (host is connected)
exchange raw data
close the socket and GPRS context
All these steps are achieved through AT commands. As for common modem interface, two logical statuses are involved: command mode and data traffic mode.
In Command Mode (CM), some AT commands are provided to configure the Data Module Internet stack and to start up the data traffic.
In data traffic mode (Socket Mode, SKTM), the client can send/receive a raw data stream which will be encapsulated in the previously configured TCP / IP packets which will be sent to the other side of the network and vice versa. Control plane of ongoing socket connection is deployed internally to the module.
For more detailed information regarding GPRS please consult Easy GPRS User Guide and AT Commands Reference Guide.
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 28 of 36
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
5 AT Commands
The Telit UC864-E/G module can be driven via the serial interface using the standard AT commands1. The Telit UC864-E/G module is compliant with:
1. Hayes standard AT command set, in order to maintain the compatibility with existing SW programs.
2. 3gpp TS 27.007 specific AT command and WCDMA/GPRS specific commands.
3. 3gpp TS 27.005 specific AT commands for SMS (Short Message Service) and CBS (Cell Broadcast Service)
4. FAX Class 1 compatible commands
Moreover the Telit UC864-E/G module supports also Telit proprietary AT commands for special purposes. For a more information about AT commands supported by UC864-E/G modules please refer to document AT Commands Reference Guide, code 80304ST10041a.
1
The AT is an ATTENTION command and is used as a prefix to other parameters in a string. The AT command combined with other parameters can be set up in the communications package or typed in manually as a command line instruction.
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 29 of 36
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
6 Conformity Assessment Issues
The Telit UC864-E is assessed to be conform to the R&TTE Directive in the WCDMA2100/GSM900/GSM1800. If the antenna connected to the module is conforming to the requirements specified under this document, it requires no further evaluation under Article 3.2 of the R&TTE Directive and do not require further involvement of a R&TTE Directive Notified Body for the final product. In all other cases, or if the manufacturer of the final product is in doubt then the equipment integrating the radio module must be assessed against Article 3.2 of the R&TTE Directive.
In all cases assessment of the final product must be made against the Essential requirements of the R&TTE Directive Articles 3.1(a) and (b), safety and EMC respectively, and any relevant Article 3.3 requirements.
The Telit UE864-E is conforming to the following European Union Directives:
• R&TTE Directive 1999/5/EC (Radio Equipment & Telecommunications Terminal Equipments)
• Low Voltage Directive 73/23/EEC and product safety
• Directive 89/336/EEC for conformity for EMC
In order to satisfy the essential requisite of the R&TTE 99/5/EC directive, the UC864-E module is compliant with the following standards:
• GSM (Radio Spectrum). Standard: EN 301 511 and 3GPP 51.010-1
• EMC (Electromagnetic Compatibility). Standards: EN 301 489-1 and EN 301 489-7
• LVD (Low Voltage Directive) Standards: EN 60 950
In this document and the Hardware User Guide, Software User Guide all the information you may need for developing a product meeting the R&TTE Directive is included.
The Telit UC864-G module is FCC Approved as module to be installed in other devices. These devices have to be used only for fixed and mobile applications. If the final product after integration is intended for portable use, a new application and FCC ID is required.
The Telit UC864-G module is conforming to the following US Directives:
• Use of RF Spectrum. Standards: FCC 47 Part 22 (GSM850/WCDMA850)
• Use of RF Spectrum. Standards: FCC 47 Part 24 (GSM1900/WCDMA1900)
• EMC (Electromagnetic Compatibility). Standards: FCC47 Part 15 To meet the FCC’s RF exposure rules and regulations:
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 30 of 36
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
• The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all the persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
• The antenna(s) used for this module must not exceed 3 dBi for mobile and fixed or mobile operating configurations.
Users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any regulatory questions and to have their complete product tested and approved for FCC compliance. Interference statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 31 of 36
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
7 SAFETY RECOMMENDATIONS
READ CAREFULLY
Be sure the use of this product is allowed in the country and in the environment required. The use of this product may be dangerous and has to be avoided in the following areas:
Where it can interfere with other electronic devices in environments such as hospitals, airports,
aircrafts, etc
Where there is risk of explosion such as gasoline stations, oil refineries, etc It is responsibility of the user to enforce the country regulation and the specific environment regulation. Do not disassemble the product; any mark of tampering will compromise the warranty validity. We recommend following the instructions of the hardware user guides for a correct wiring of the
product. The product has to be supplied with a stabilized voltage source and the wiring has to be conforming to the security and fire prevention regulations.
The product has to be handled with care, avoiding any contact with the pins because electrostatic discharges may damage the product itself. Same cautions have to be taken for the SIM, checking carefully the instruction for its use. Do not insert or remove the SIM when the product is in power saving mode.
The system integrator is responsible of the functioning of the final product; therefore, care has to be taken to the external components of the module, as well as of any project or installation issue, because the risk of disturbing the WCDMA/GSM network or external devices or having impact on the security. Should there be any doubt, please refer to the technical documentation and the regulations in force.
Every module has to be equipped with a proper antenna with specific characteristics. The antenna has to be installed with care in order to avoid any interference with other electronic devices and has to guarantee a minimum distance from the body (20 cm). In case of this requirement cannot be satisfied, the system integrator has to assess the final product against the SAR regulation.
The European Community provides some Directives for the electronic equipments introduced on the market. All the relevant information’s are available on the European Community website:
http://europa.eu.int/comm/enterprise/rtte/dir99-5.htm
The text of the Directive 99/05 regarding telecommunication equipments is available, while the applicable Directives (Low Voltage and EMC) are available at:
http://europa.eu.int/comm/enterprise/electr_equipment/index_en.htm
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 32 of 36
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
7.1 Contact Information, Support
Our aim is to make this guide as helpful as possible. Keep us informed of your comments and suggestions for improvements.
For general contact, technical support, report documentation errors and to order manuals, contact your regional Technical Support Center at:
TS-EMEA@telit.com,
TS-AMERICAS@telit.com,
TS-APAC@telit.com
Or use: http://www.telit.com/en/products/technical-support-center/contact.php Telit appreciates feedback from the users of our information. Technical documentation: available for download into the Website www.telit.com >Products
>UMTS/HSDPA > selected model.
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 33 of 36
ACM
ASCII
AT
CB
CBS
CCM
CLIP
CLIR
CMOS
CR
CSD
CTS
DAI
DCD
DCE
DRX
DSR
DTA
DTE
DTMF
DTR
EMC
ETSI
FTA
GPRS
GPS
GSM
HF
HSDPA
IMEI
IMSI
IRA
ITU
IWF
LCD
LED
LF
ME
MMI
List of acronyms
Accumulated Call Meter American Standard Code for Information Interchange Attention commands Cell Broadcast Cell Broadcasting Service Call Control Meter Calling Line Identification Presentation Calling Line Identification Restriction Complementary Metal-Oxide Semiconductor Carriage Return Circuit Switched Data Clear To Send Digital Audio Interface Data Carrier Detected Data Communications Equipment Data Receive Data Set Ready Data Terminal Adaptor Data Terminal Equipment Dual Tone Multi Frequency Data Terminal Ready Electromagnetic Compatibility European Telecommunications Equipment Institute Full Type Approval (ETSI) General Radio Packet Service Global Positioning System Global System for Mobile communication Hands Free High Speed Downlink Packet Access International Mobile Equipment Identity International Mobile Subscriber Identity International Reference Alphabet International Telecommunications Union Inter-Working Function Liquid Crystal Display Light Emitting Diode Linefeed Mobile Equipment Man Machine Interface
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 34 of 36
MO
MS
MT
OEM
PB
PDU
PH
PIN
PLMN
PUCT
PUK
RACH
RLP
RMS
RTS
RI
SCA
SIM
SMD
SMS
SMSC
SS
TIA
UDUB
UMTS
USB
USSD
WCDMA
3gpp
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
Mobile Originated Mobile Station Mobile Terminated Other Equipment Manufacturer Phone Book Protocol Data Unit Packet Handler Personal Identity Number Public Land Mobile Network Price per Unit Currency Table PIN Unblocking Code Random Access Channel Radio Link Protocol Root Mean Square Ready To Send Ring Indicator Service Center Address Subscriber Identity Module Surface Mounted Device Short Message Service Short Message Service Center Supplementary Service Telecommunications Industry Association User Determined User Busy Universal Mobile Telecommunications System Universal Serial Bus Unstructured Supplementary Service Data Wideband Code Division Multiple Access 3rd Generation Partnership Project
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 35 of 36
[[dddd//mmmm//yyyyyyyy]]
8 Document Change Log
UC864-E/G Product Description
80281ST10034a Rev. 1 - 08/08/2008
RReevviissiioonn DDaattee
CChhaannggeess
0 Draft 07/11/2007 Initial issue 1 08/08/2008 general revision of the document
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 36 of 36
Loading...