Page 1
Owner’s Manual
Please read before using this equipment.
CD Graphics Karaoke System
with Single Cassette
Page 2
WARNING:
!
shock hazard, do not expose this product to rain
or moisture.
CAUTION:
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.
!
To reduce the risk of fire or
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
TO REDUCE THE RISK OF
This symbol is intended to alert
you to the presence of uninsulated dangerous voltage within
the product’s enclosure that might
be of sufficient magnitude to constitute a risk of electric shock. Do
not open the product’s case.
This symbol is intended to inform
you that important operating and
maintenance instructions are
included in the literature accompanying this product.
ˆ
Important Safety Instructions
Read Instructions
— All the safety and
operating instructions should be read
Follow Instructions
and use instructions should be followed.
before the product is operated.
Cleaning
Retain Instructions
— The safety and
operating instructions should be retained for future reference.
Heed Warnings
— All warnings on the
product and in the operating instructions
the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
Attachments
ments not recommended by the product
should be adhered to.
2001 RadioShack Corporation.
©
RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.
2
All Rights Reserved.
— All operating
— Unplug this product from
— Do not use attach-
Page 3
manufacturer as they may cause hazards.
Water and Moisture
— Do not use this
product near water (for ex ample, near a
bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement, or near
a swimming pool, and the like).
Accessories
— Do not place this product on an unstable cart, stand, tripod,
bracket, or table. The product may fall,
causing serious injury to a child or adult,
and serious damage to the product. Use
only with a cart, stand, tripod, bracket, or
table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the
manufacturer’s instructions, and should
use a mounting accessory recommen ded by the manufacturer.
A product and cart combination should be
moved with care. Quick
stops, excessive force,
and uneven surfaces
may cause the appliance and cart combination to overturn.
Power Sources
— This product should
be operated only from the type of power
source indicated on the marking label. If
you are not sure of the type of power
supply to your home, consult your product dealer or local power company. For
products intended to operate from battery power, or other sources, refer to the
operating instruction.
Grounding or Polarization
— This
product may be equipped with a polarized alternating current line plug (a plug
having one blade wider than the other).
This plug will fit into the power outlet
only one way. This is a safety feature. If
you are unable to insert the plug fully
into the outlet, try reversing the plug. If
the plug should still fail to fit, contact
your electrician to replace your obsolete
outlet. Do not defeat the safety purpose
of the polarizes plug.
Power-Cord Protection
— Power supply cords should be routed so that they
are not likely to be walked on or pinched
by items placed upon or against them,
paying particular attention to cords at
plugs, convenience receptacles, and
point where they exit from the product.
Ventilation
— Slots and openings in the
cabinet are provided for ventilation, to
ensure reliable operation of the product,
and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a b ed,
sofa, rug, or other similar surface. This
product should not be placed in a built-in
installation such as a bookcase or rack
unless proper ventilation is provided or
the manufacturer’s instructions have
been adhered to.
Outdoor Antenna Grounding
— If an
outside antenna is connected to the receiver, be sure the antenna system is
grounded so as to provide some
protection against voltage surges and
built-up static charges. Article 810 of the
National Electrical Code, ANSI/NFPA
70, provides information with regard to
proper grounding of the mast and supporting structure, grounding of the mast
and supporting structure, grounding of
the lead-in wire to an antenna-discharge
unit, size of grounding conductors, location of antenna-discharge unit, connec-
3
Page 4
tion to grounding electrodes, and
requirements for the grounding electrode. See figure.
Servicing
— Do not attempt to service
this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer
all servicing to qualified service personnel.
Lightning
— For added protection for
this product during a lightning storm, or
when it is left unattended and unused for
long periods of time, unplug it from the
wall outlet and disconnect the antenna
or cable system. This will prevent damage to the product due to lightning and
power-line surges.
Power Lines
— An outside antenna
system should not be located in the vicinity of overhead power lines or other
electric light or power circuits, or where
it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be
taken to keep from touching such power
lines or circuits as contact with them
might be fatal.
Overloading
— Do not overload wall
outlets, extension cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
Damage Requiring Service
— Unplug
this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
• When the power-supply cord or plug
is damaged,
• If liquid has been spilled, or objects
have fallen into the product,
• If the product has been exposed to
rain or water,
• If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the o perating instructions as an improper
adjustment of other controls may
result in damage and will often
require extensive work by a qualified
technician to restore the product to
its normal operation,
• If the product has been dropped or
damaged in any way, and
• When the product exhibits a distinct
change in performance – this indicates a need for service.
Object and Liquid Entry
objects of any kind into this product
through openings, as they may touch
dangerous voltage points or short-out
parts that could result in a fire or electric
shock. Never spill liquid of any kind on
the product.
4
— Never push
Replacement Parts
— When replacement parts are required, be sure the service technician has used replacement
parts specified by the manufacturer or
have the same characteristics as the
original part, Unauthorized substitutions
Page 5
may result in fire, electric shock, or other
hazards.
Safety Check
any service or repairs to this product,
ask the service technician to perform
safety checks to determine that the
product is in proper operating condition.
ˆ
Features
Your RadioShack CD Graphics Karaoke
System is a stylish, affordable karaoke
system with a full array of great features.
It lets you sing along with your favorite
recordings on a CD, CDG (compact disc
with a graphic track), or cassette tape,
and hear your voice over the music
through the powerful built-in speaker.
The karaoke system lets you play regular or karaoke CDs or CDGs, so you can
experience digital images. You can connect the karaoke system to a TV or monitor and read the lyrics of your favorite
tunes as they scroll in front of a still video background. You can also connect a
stereo VCR to the karaoke system and
play a karaoke video cassette (not supplied) to accompany your singing and
provide the lyrics.
Or, you can sing along without video,
using special karaoke audio cassette
tapes (such as the one we have included to get you started) that let you balance the volume of the original singer’s
voice and the music tracks. You can
even sing along with your favorite prerecorded cassette tapes and CDs!
— Upon completion of
Wall or Ceiling Mounting
uct should be mounted to a wall or ceiling only as recommended by the
manufacturer.
Heat
— The product should be situated
away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
Note:
Additional karaoke CDs, audio
cassettes, and video cassettes are
available by special order through your
local RadioShack store.
Plus, you can use your karaoke system
as a portable PA system for speaking at
parties or other gatherings — just plug in
the microphone and turn on the power!
8-Watt Output Power
along through one of the biggest amps
offered in a karaoke system, and listen
through a 6-inch, full range speaker.
Adjustable Echo
to enrich your voice for a live concert
hall effect.
Tape Speed Control
the tape speed to match your voice
pitch.
Supplied Karaoke Audio Tape and
CDG Disc
music.
Automatic Voice Control
replace the original singer’s voice with
your voice when you use a karaoke
tape, so you can sing along.
— let you sing along with the
— lets you add echo
— The prod-
— lets you sing
— lets you adjust
— lets you
5
Page 6
Auxiliary Input Jacks
nect another audio input source, such as
a stereo VCR or tuner.
Auxiliary Output Jacks
nect another audio component, such as
an equalizer/booster or a PA system.
ˆ
Making Connections
— lets you con-
— let you con-
Dual Microphone Jacks
use the supplied microphone along with
an optional microphone to sing duets or
lead and background vocals.
— lets you
Caution:
not connect the system to AC power until all other connections are complete.
To avoid electrical shock, do
CONNECTING
MICROPHONES
The system has two microphone jacks,
so you can use the supplied microphone
to sing along with your favorite recordings, and connect an optional microphone (not supplied, available at your
local RadioShack store) for duets or
lead and background vocals. For the
best performance, the microphone
should be a unidirectional 600-ohm dynamic type with a
plug and an ON/OFF switch.
Before you connect a microphone, set
MIC VOLUME
crophone into
microphone, plug it into
to
MIC 1
1
/4-inch (6.35-mm)
MIN
. Plug a single mi-
. If you add a second
MIC 2
.
side of the system and place the microphone in the holder’s grip.
CONNECTING A TV
To see the words and images from a
karaoke video cassette or CD/CDG on a
TV or monitor, plug one end of the supplied cable into
er end into your TV or monitor’s VIDEO
IN jack.
VIDEO OUT
and the oth-
CONNECTING AN AUDIO
COMPONENT
AUX
OUT IN VIDEO OUT
To store the microphone, pull down the
built-in microphone holder on the left
6
To sing along with music from an optional audio component (such as a tuner, A/
V receiver, or VCR), connect the component’s audio output (red and white RCA)
jacks to the
To hear your voice and music from the
system through an optional audio com-
AUX IN R
and L jacks.
Page 7
ponent (such as an equalizer/booster or
PA system), connect the component’s
audio input jacks to the
AUX OUT
jacks.
Caution:
a polarized plug that fits into the outlet
only one way. If the plug does not fit
properly, turn it over and try again. Do
CONNECTING TO POWER
not force it.
When you have made all other connections, plug your system’s power cord
into a standard AC outlet.
ˆ
CD/CDG Player Operation
The supplied power cord has
1. Press
POWER
to turn on the system.
The power indicator lights.
2. Set
FUNCTION SELECT
3. Press
PUSH OPEN
to open the CD/
to
CD+G
.
CDG door.
4. Place a CD/CDG in the compartment tray over the center hub, with
the label facing up.
SKIP/SEARCH
INTRO
5. Press
PUSH CLOSE
to close the CD/
CDG compartment.
0 0
then the
CD/CDG’s total number of tracks
appear.
6. Press
PLAY/PAUSE
. The PLAY/
PAUSE indicator lights (CDG only)
and the CD/CDG begins to play
from Track 1.
PUSH CLOSE
PUSH OPEN
PLAY/
PAUSE
STOP
REPEAT
PROGRAM
POWER
FUNCTION
SELECT
7
Page 8
7. The system automatically stops at
the end of the CD/CDG’s last track.
To stop it sooner, press
Notes:
STOP
.
To repeat all the tracks, press
twice. The REPEAT indicator lights.
To cancel repeat play, press
again. The REPEAT indicator turns off.
REPEAT
REPEAT
• To temporarily stop play, press
PLAY/PAUSE
PLAY/PAUSE indicator flash. To
resume play, press
again.
• Do not apply excessive force to the
CD/CDG door, or press the door
while a CD/CDG is playing.
• Never place anything except a compact disc on the disc tray. Foreign
objects can damage the player.
• Never place more than one disc on
the disc tray at a time.
. The track number and
PLAY/PAUSE
SKIPPING TRACKS
While the disc is stopped, you can skip
up or down to the desired track by
pressing
play the selected track, press
PAUSE
SKIP/SEARCH
.
or . To
PLAY/
SEARCH PLAY (CD ONLY)
INTRO SCAN
You can set the system to play the first
10 seconds of each track so you can
quickly find the one you want.
INTRO
Press
the first 10 seconds of each track, beginning with the first track, then stops.
To cancel intro scan during or after play,
press
during play, the CD/CDG player begins
normal play.
Note:
ing intro scan.
. The CD/CDG player plays
INTRO
. If you cancel intro scan
You can also use repeat play dur-
PROGRAM PLAY
You can program the CD/CDG player to
play up to 20 tracks in any order you
choose.
1. Press
STOP
. The PLAY/PAUSE indi-
cator turns off.
Hold down
forward or backward during play. The
CD plays rapidly and you can hear the
sound at a high speed.
SEARCH
REPEAT PLAY
To repeat the current track, press
PEAT
once. The REPEAT indicator
flashes.
8
to search rapidly
RE-
2. Press
indicator flashes.
3. Press
select the desired track. The track
number continues to flash.
4. Press
selected track. The PROGRAM indicator flashes.
5. Repeat Step 3 and 4 to program up
to 20 tracks.
PROGRAM
SKIP/SEARCH
PROGRAM
. The PROGRAM
or to
to store the
Page 9
Note:
The 21st track you program
replaces the first stored track, and
each additional track you program
replaces the next successive track.
6. Press
PLAY/PAUSE
to play the
stored tracks. The first stor ed track
number appears.
7. Program play automatically stops at
the end of the last programmed
track. To stop play sooner, press
STOP
.
Note:
You can use intro scan during
program play.
Reviewing/Replacing a
ˆ
Cassette Deck Operation
Programmed Sequence
While play is stopped, repeatedly press
PROGRAM
to review the programmed
sequence.
To replace a programmed track, press
PROGRAM
place appears. Press
until the track you want to re-
SKIP/SEARCH
or to select the desired track,
then press
PROGRAM
to store the track.
Erasing a Programmed
Sequence
To erase a programmed sequence,
PUSH OPEN
press
grammed play, or press
before or after pro-
POWER
.
1. Press
STOP/EJECT
to open the
cassette compartment door.
2. Insert a cassette with the exposed
tape down and the desired side facing you. Avoid touching the tape.
POWER
RECORD
PLAY
REWIND
3. Close the cassette compartment
door and press the center or right
portion of the door until it clicks shut.
4. Press
5. Slide
F/FWD.
POWER
FUNCTION SELECT
STOP/
EJECT
on.
PAUSE
TAPE
to
FUNCTION
SELECT
.
9
Page 10
6. Press
PLAY
.
Notes:
7. Rotate
ANCE
MASTER VOLUME
to suit your listening prefer-
and
BAL-
ences.
8. When the tape reaches its end, the
deck automatically stops and
is released. Or, press
STOP/EJECT
PLAY
to stop play sooner.
9. Press
STOP/EJECT
again to eject
the tape.
ˆ
Karaoke Operation
When a microphone is plugged into
MIC1
or
MIC 2
, the system mixes the microphone output with recorded music
from cassette tapes, CDs, or CDGs. Ro-
MIC VOLUME
tate
tening level, and
to a comfortable lis-
AUTO VOICE CONTROL
for the best balance between playback
and microphone levels.
Rotate
to vocals, and
ECHO
to add depth and richness
TAPE SPEED
to change
the pitch of the music to match your vocal range.
SINGING ALONG WITH A
CD/CDG OR A CASSETTE
TAPE
1. Press
2. Load a CD/CDG in the CD compart-
3. Set
POWER
to turn on the system.
The POWER indicator lights.
ment or a cassette tape in the
cassette compartment.
FUNCTION SELECT
TAP E
or
.
to
CD/CDG
• To temporarily stop play, press
PAUSE
. Press
PAUSE
again to
resume play.
• To rapidly wind the tape forward or
backward, press
STOP/EJECT
Press
F.FWD
when you reach
or
REWIND
the desired section.
4. Press
PLAY/PAUSE
or
PLAY
on the
tape deck to start play.
5. Adjust
MASTER VOLUME
to the
desired level.
6. Set the microphone's
ON
to
and rotate
ON/OFF
MIC VOLUME
switch
adjust its volume.
7. Adjust
ECHO
for desired reverbera-
tion.
If you are playing a tape, rotate
TAPE SPEED
so the pitch of music
matches your voice.
If you are using a karaoke ca ssette
tape, rotate
AUTO VOICE CONTROL
to adjust the volume of the prerecorded original singer's voice in
relation to the music.
Note:
AUTO VOICE CONTROL
has
no effect on a regular (non-karaoke)
pre-recorded cassette tape.
8. When you finish, press
CD/CDG. Then press
STOP
on the
PUSH OPEN
.
to
10
Page 11
to open the compartment door and
remove the CD/CDG.
To stop a tape, press
on the deck. Press
STOP/EJECT
STOP/EJECT
again to open the compartment door
and remove the cassette tape.
9. Set the microphone's
OFF
to
, then press
ON/OFF
POWER
switch
to turn off
the system.
USING THE KARAOKE
SYSTEM WITH AN
OPTIONAL AUDIO
COMPONENT
If you connected an optional audio component (see “Connecting an Audio Com ponent” on Page 6), follow these steps
to hear the music from that comp onent,
or to hear your voice with the music.
1. Set
2. Press
FUNCTION SELECT
POWER
to turn on the system.
The POWER indicator lights.
3. Turn on the audio component.
4. Rotate
ECHO
MASTER VOLUME
and
to the desired levels.
5. To hear your voice with the music,
set the microphone's
to
ON
. Rotate
MIC VOLUME
your voice's volume.
6. When you finish, set the microphone's
Press
ON/OFF
POWER
switch to
to turn off the system,
then turn off the audio component.
AUX
to
ON/OFF
to adjust
.
switch
OFF
RECORDING YOUR VOICE
WITH MUSIC
Follow these steps to make a recording
of your voice with music from the system’s CD/CDG or an optional audio
component.
1. Load a blank audio cassette (or one
you want to record over) in the
cassette deck (see “Cassette Deck
Operation” on Page 9).
2. Follow Steps 1–6 in “CD/CDG
Player Operation” on Page 7 or
Steps 1–6 in “Using the Karaoke
System with an Optional Audio
Component” on Page 1 1.
3. Set
4. To record your voice with a CD/
5. Press
.
FUNCTION SELECT
a CD/CDG or
AUX
to
for an optional
audio component.
CDG, repeatedly press
SEARCH
or until the
desired track number appears.
To record your voice with music
from an optional audio component,
turn on the optional component.
PLAY/PAUSE
RECORD
and
, then press both
PLAY
on the cassette
deck at the same time. The tape
deck records your voice along with
the sound from the CD/CDG or the
optional audio component.
CD+G
for
SKIP/
11
Page 12
ˆ
Troubleshooting
If your karaoke system is not working properly, the following
Problem Possible Cause Solution
No power when
POWER
No sound.
Sound from an audio
cassette tape is irregular or distorted.
Cannot record. The erase-prevention tabs have
CD skips or will not
play.
No song lyrics appear
on screen.
is on.
No power plug connection at the
AC outlet.
MASTER VOLUME
VOLUME
setting.
The wrong function is selected. Slide
Dirty head or capstan. See “Cleaning the Tape-Han-
Irregular cassette tape winding. See “Restoring Tape Tension
been removed from the
cassette.
Disc is inserted upside down. Insert CD correctly.
Disc is dirty. Wipe clean with soft cloth.
Disc is scratched. Use a new disc.
Moisture has formed inside the
CD deck.
Video cable is not connected
properly to the TV.
TV’s source selector is not set
to VIDEO.
is set to the lowest
or
MIC
Insert the power plug into the
AC outlet.
Adjust
MIC VOLUME
the correct function.
dling Parts” on Page 14.
and Sound Quality” on Page 14.
See “Preventing Accidental Era-
sure” on Page 14.
Turn the CD player on and let it
dry for 20 to 30 minutes.
Connect the video cable to
VIDEO OUT
VIDEO IN.
Use your TV’s remote control to
select VIDEO.
suggestions might help.
MASTER VOLUME or
.
FUNCTION SELECT
and to the TV’s
to
If you cannot find the problem, take your karaoke system to your local RadioShack
store for assistance.
12
Page 13
ˆ
Care and Maintenance
To enjoy your karaoke system for a long
time:
• Keep the karaoke system dry. If it
gets wet, wipe it dry immediately.
• Use and store the karaoke system
only in normal temperature environments.
• Handle the karaoke system gently
and carefully. Do not drop it.
• Keep the karaoke system away from
dust and dirt.
• Wipe the karaoke system with a
damp cloth occasionally to keep it
looking new.
Modifying or tampering with the karaoke
system’s internal components
cause a malfunction and might invalidate its warranty and void your FCC authorization to operate it
system is not performing as it should,
take it to your local RadioShack store for
assistance.
. If your karaoke
can
more of the following corrective measures:
• reorient or relocate the receiving
antenna
• increase the distance between the
equipment and the radio or TV
• use outlets on different electrical circuits for the equipment and the
radio or TV
Consult your local Radio Shack store if
the problem still exists.
You must use shielded interfac e cables
with this equipment.
CD CARE TIPS
Even though a compact disc is durable,
treat the CD surface with care.
• Do not write on either side of the
CD, particularly the non-label side
(signals are read from the non-label
side).
THE FCC WANTS YOU TO
KNOW
This equipment complies with the limits
for a Class B digital device as specified
in Part 15 of
provide reasonable protection against
radio and TV interference in a residential
area. However, your equipment might
cause TV or radio interference even
when it is operating properly. To eliminate interference, you can try one or
FCC Rules
. These limits
• Do not store CDs in high temperature, high-humidity locations. They
might warp.
• Keep CDs dry. A water drop can act
as a lens and affect the laser
beam’s focus.
• Always handle a CD by the edges to
avoid fingerprints and always keep it
in its protective case or sleeve when
it is not in use. Fingerprints and
scratches on the CD’s surface can
prevent the laser beam from cor-
13
Page 14
rectly reading the digital information.
If the CD gets scratched, use
RadioShack Scratch ‘n Fix to repair
the disc.
TAPE TIPS
Restoring Tape Tension and
Sound Quality
After you play a cassette tape several
times, the tape might become tightly
wound on the reels. This can cause
playback sound quality to deteriorate.
To restore the sound quality, fastforward the tape from the beginning to
the end of one side, then completely rewind it. Then loosen the tape reels by
gently tapping each edge of the cassett e
on a flat surface.
Caution:
cassette when tapping it. Do not touch
the exposed tape or allow any sharp objects near the cassette.
Be careful not to damage the
Preventing Accidental Erasure
Cassette tapes have two eraseprotection tabs — one for each side.
When a tab is in place, you can record
on that side.
To prevent accidental erasure of a tape
recording, use a screwdriver to remove
one or both of the cassette tape’s eraseprotection tabs. This prevents
from being pressed.
If you later decide to record on a tape
side after you have removed the eraseprotection tab, place a piece of strong
plastic tape over that side’s eraseprotection hole. Be sure you cover only
the hole originally covered by the eraseprotection tab.
Caution:
protection tabs does not prevent a bulk
eraser from erasing a cassette tape.
Removing the erase-
RECORD
CLEANING THE TAPEHANDLING PARTS
Erasing Tapes
To record over a cassette tape, simply
record as usual. The cassette deck
records over the previous recording.
You can quickly erase both sides of a
cassette tape using a RadioShack bulk
tape eraser.
Note
: If you use metal or high-bias type
tape, the recorded sound might not be
erased properly.
14
Dirt, dust or particles of the tape's coat ing can accumulate on the tape heads
and other parts that the tape touches.
This can greatly reduce the performance
of the cassette player. After every 20
hours of tape player operation, follow
these steps to clean the tape-handling
parts or use a RadioShack cassette
deck cleaning kit.
1. Disconnect AC power.
2. Open the cassette compartment
door and press
tape-handling parts.
PLAY
to expose the
Page 15
3. Use a cotton swab dipped in denatured alcohol or tape head cleaning solution to
clean the tape guides, record/play head, erase head, pinch roller, and capstan.
Tape Guides
Erase Head Record/Playback Head
4. When you finish cleaning, press
STOP/EJECT
Pinch Roller
and close the cassette compart-
Capstan
ment door. Then reconnect power.
ˆ
Specifications
Power Output (Maximum) .............................................................................................. 8 Watts
Impedance Output ......................................................................................................... 4 Ohms
Frequency Response (CD Player Section) ........................................... 20 Hz–20 KHz (±3 dB)
Signal-to-Noise Ratio ........................................................... ... ... ....................................... 70 dB
D/A Conversion ........................................................................................................... 1 Bit DAC
Wow and Flutter (WRMS) ................................................................................ Less than 0.35%
Frequency Response (Cassette Deck Section) ............................................... 125 Hz–6.3 KHz
(±5 dB) 4.75 cm/sec.
AC Input Power .................................................................................................. AC 120V 60Hz
1
Dimensions (HWD) .......................................................................... 16
Weight ...................................................................................................................... 18 lb (8 kg)
Included Accessories ..................................................................... Prerecorded Karaoke Tape,
Prerecorded Karaoke CD+G Disc,
AV Cable, Dynamic Microphone
Specifications are typical; individual units might vary. Specifications are subject to change and
improvement without notice.
/2 × 111/16 × 81/16 Inches
(419 × 281 × 205 mm)
15
Page 16
Limited Ninety-Day Warranty
This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for ninety (90) days from the date of purchase from RadioShack companyowned stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED
HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES,
INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES
CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE
OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT,
SPECIAL, INCIDENT AL, OR CONSEQ UENTIAL DAMAGES, EVEN IF RadioShac k HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limit ation of incidental or consequential damages, so the above limitations or exclusions may not apply to
you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, unless otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the property of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallat i on.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
12/99
RadioShack Corporation
Fort Worth, Texas 76102
A
32-1165
610-1165-01
06A01
Printed in China
Loading...