Page 1
2.4GHz Cordless Phone
with Caller ID and Digital Answering Machine
43-3857
Ten Number Memory Dialing—stores ten
numbers in memory for easy dialing. See “Memory
Dialing” on page 13.
Long Battery Life—the supplied battery pack
(when fully charged) provides about seven hours
of talk time or 14 days of standby time.
20 Channels—automatically selects a clear
channel when you make or answer a call. You can
also manually change channels during a call. See
“Selecting a Different Channel” on page 13.
Headset Jack—connects an optional headset
(available at your local RadioShack store) for
hands-free convenience. See “Headset
Installation” on page 40.
Toll-Saver—lets you avoid unnecessary charges
when you call by long distance to check your
messages. See “Setting the Ring Time” on
page 28.
IMPORTANT
If an icon appears at the end of a paragraph, go to the
!
box on that page with the corresponding icon for
pertinent information.
— Warning! — Important — Caution
o
Ô — Note
!
RadioShack and RadioShack.com are trademarks used by
ENERGYSTAR and the ENERGYSTAR certification mark
OWNER’S MANUAL
Please read before using this equipment.
© 2004 RadioShack Corporation.
All Rights Reserved.
RadioShack Corporation.
are registered US marks.
Page 2
CONTENTS
Introduction .......................................... 3
Important Information .......................... 3
FCC Statement .................................... 3
Surge Protection ........................................ 5
Important Safety Instructions ............... 5
Important Caller ID Information ........... 6
Installation ........................................... 6
Mounting the Phone .................................. 6
On a Desk Top .................. .. ... ................... 7
Connecting, Charging and Replacing
the Battery Pack ..................................... 7
Setting Menu Options ................................ 9
Changing the Auto Talk and CIDCW ......... 9
Entering your Area Code ........................... 9
Choosing the Dial Mode . ... .. .................... 10
Setting the Language ..............................10
Operation ........................................... 11
Making and Receiving Calls .................... 11
Adjusting the Handset Ringer and
Earpiece Volume ....................... ... .. ...... 12
Handset Ringer Tone and Volume .......... 12
Earpiece Volume . .................................... 12
Temporarily Mute the Handset
Ringer ...................................................12
Redial ...................................................... 12
Tone Dialing Switch-over ......................... 12
Traveling Out-of-Range ............................ 13
Selecting a Different Channel .................. 13
Page ........................................................ 13
Flash and Call Waiting ............... ... ... ........ 13
Memory Dialing ................................. 13
Storing Phone Numbers and
Names .......................... ........................ 13
Steps for Entering Names and Special
Characters ................. ........................... 15
If You Make a Mistake while Entering
a Name ................................................. 16
Making Calls with Memory Dialing .......... 16
Memory Dialing from Standby Mode .......16
Memory Dialing from Talk Mode .............17
Chain Dialing ........................................... 17
Editing a Stored Name and/or Phone
Number ...................... ........................... 17
Erasing a Stored Name and Phone
Number ...................... ........................... 19
Testing Stored Emergency Numbers ....... 19
One-touch Speed Dial ............................. 20
Storing and Editing the Speed Dial
Making Calls with the Speed Dial ............ 20
Deleting the Speed Dial ........................... 20
......... 20
Caller ID ............................................ 21
When the Telephone Rings ..................... 21
Viewing the Caller ID Message List ......... 22
Deleting Information from the Caller ID
List .......................... .............................. 22
Deleting a Caller ID Message
Deleting all Caller ID
Names/Numbers ................... ............... 23
Using the Caller ID List ............................ 23
Calling a Party from the Caller ID
List ......................... ........ ........ ....... ...... .. 23
Long Distance Calls and Area Code
Setting/Cancellation ........ ..................... 24
Storing Caller ID Messages in Memory
Dialing ........................... ....................... 24
................. 23
The Integrated Answering Device ...... 25
Features .................................................. 25
Turning the Answering System
On/Off ....................... ............................ 26
Setting Up Your Answering System ........ . 26
Using the Menu Mode ............................. 26
Setting the Time ................. ... ... ...............27
Setting a Personal Security Code
(PIN) ........................ ........................ .....2 8
Setting the Ring Time ..............................28
Selecting the Message Record Time ......29
Setting the Message Alert Tone ..............30
Selecting the Language ..........................31
Setting Your Outgoing Message
(Greeting) ............................................. 32
Using Your Answering System ................. 34
Remote Operation ................................... 37
Additional Information ........................ 40
Installing the Optional Beltclip ................. 40
Headset Installation ................................. 40
Troubleshooting ................................. 41
Care ................................................... 43
Service and Repair ............................ 43
2
Page 3
WARNING: To reduce the risk of fire or shock hazard, do not expose this product to rain or moisture.
.CAUTION.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The exclamation symbol is intended to
inform you that important operating and
maintenance instructions are included in
!
the literature accompanying this produc t.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER OR BACK. NO
USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED PERSONNEL.
!
The lightning symbol is intended to alert you to
the presence of uninsulated dangerous voltage
within this product’s e nc los ur e th at mi ght be o f
sufficient magnitude to constitute a risk of
electric shock. Do not open th e product’s case.
INTRODUCTION
Thank you for purchasing a RadioShack 2.4 GHz
Cordless Telephone. Your telephone provides
excellent clarity and range and integrates Caller ID,
Caller ID on Call Waiting, and a digital answering
system into one space-saving device. The 2.4 GHz
band provides superior audio quality and extended
range.
The digital answering system provides clear reliable
messaging with call screening, day/time stamp, call
counter, remote access and instant skip or replay
messaging.
The Caller ID records each caller’s name (if
available in your area), telephone number, and the
date and time of the call, as provided by your local
phone company to Caller ID service subscribers.
IMPORTANT
INFORMATION
This telephone has been tested and found to
comply with all applicable UL and FCC standards.
IMPORTANT
!
• When AC power is lost,
the phone loses the
digital security code
connection between the
base and the handset.
When power is restored,
put the handset on the
base briefly to restore
this connection so you
can use the handset.
• Your phone operates on
standard radio
frequencies as allocated
by the FCC.
• It is possible for other
radio units operating
nearby on similar
frequencies to
unintentionally intercept
your conversation or
cause interference. This
possible lack of privacy
can occur with any
cordless phone.
!
!
Introduction
FCC STATEMENT
Your telephone compiles with Part 68 of the FCC
Rules.Upon request, you must provide the phone’s
FCC registration number and REN to your phone
company. These numbers are on the base unit.
3
Page 4
Ô NOTE Ô
You must not connect your
telephone to:
• coin-operated systems
• most electronic key
phone systems
FCC Statement
Your phone is not intended to be used with partyline systems. Connection to party line service is
subject to state tariffs. Contact the state public utility
commission, public service commission, or
corporation commission for information. Ô
We have designed your phone to conform to federal
regulations, and you can connect it to most
telephone lines. However, each phone (and each
device, such as a telephone or answering machine)
that you connect to the telephone line draws power
from the telephone line. We refer to this power draw
as the device’s ringer equivalence number, or REN
on the back of your phone.
If you use more than one phone or other device on
the line, add up all of the RENs. If the total is more
than five (three in rural areas), your telephones
might not ring. If ringer operation is impaired,
remove a device from the line.
In the unlikely event that your phone causes
problems on the phone line, the phone company
can temporarily discontinue your service. If this
happens, the phone company attempts to notify you
in advance. If advance notice is not practical, the
phone company notifies you as soon as possible
and advises you of your right to file a complaint with
the FCC.
Also, the phone company can make changes to its
lines, equipment, operations, or procedures that
could affect the operation of this phone. The
telephone company notifies you of these changes in
advance, so you can take the necessary steps to
prevent interruption of your telephone service.
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) This device must accept any interference
received, including interference that may cause
undesired operation. Privacy of communications,
may not be ensured when using this phone.
4
Page 5
SURGE PROTECTION
Your telephone has built-in protection circuits to
reduce the risk of damage from surges in telephone
line and power line current. These protection
circuits meet or exceed the FCC requirements.
However, lightning striking the telephone or power
lines can damage your telephone.
Lightning damage is not common. Nevertheless, if
you live in an area that has severe electrical storms,
we suggest that you unplug your phone when
storms approach to reduce the possibility of
damage.
IMPORTANT SAFETY
INSTRUCTIONS
When using your telephone equipment, basic safety
precautions should always be followed to reduce
the risk of fire, electric shock and injury to persons,
including the following:
1. Do not use this product near water, for
example, near a bathtub, wash bowl, kitchen
sink, or laundry tub, in a wet basement or near
a swimming pool.
2. Avoid using a telephone (other than a cordless
type) during an electrical storm. There may be
a remote risk of electric shock from lightning.
As an ENERGYSTAR Partner,
RadioShack Corporation has
determined that this product
meets the E
guidelines for energy
efficiency.
NERGYSTAR
3. Do not use the telephone to report a gas leak in
the vicinity of the leak.
4. Use only the power cord and batteries
indicated in this manual. Do not dispose of
batteries in a fire. They may explode. Check
with local codes for possible special disposal
instructions.
SAVE THESE
INSTRUCTIONS
Important Safety Instructions
5
Page 6
Important Caller ID Information
IMPORTANT
!
Cordless phones such as
this one require AC power
to operate. When the AC
power is off, you cannot dial
out or receive incoming
calls using your phone. To
be safe, you should also
have a phone that does not
need AC power to operate
(not a cordless phone) so
you can still make and
receive calls if there is an
AC power failure.
IMPORTANT CALLER ID
INFORMATION
To use Caller ID and Caller ID on Call Waiting, you
must be in an area where those services are
available and you must subscribe to those services
through your local phone company. Where Caller ID
is offered, one or more options are generally
available:
• caller’s number only
• caller’s name only
• caller’s name and number
If you subscribe to Call Waiting ID and Caller ID, the
system can show you the incoming caller
!
information, even when you are already talking on
the phone.
INSTALLATION
Before using your phone, carefully peel the
protective film off the display. The film protects the
handset window during shipment and is not
necessary for use.
MOUNTING THE PHONE
You can place the phone on a desk or table.
Choose a location that is:
Ô
!
Ô NOTE Ô
If your home has specially
wired alarm equipment
connected to the telephone
line, be sure that installing
the system does not disable
your alarm equipment.
If you have questions about
what will disable alarm
equipment, contact your
telephone company or a
qualified installer.
6
• near an AC outlet
• near a modular telephone line jack
• out of the way of normal activities
• away from electrical machinery, electrical
appliances, metal walls or filing cabinets,
wireless intercoms, alarms, and room monitors
• away from other cordless phones
You can try different locations to see which provides
the best performance.
Page 7
Your telephone connects directly to a modular
telephone line jack. If your telephone wiring does
not have a modular jack, you can update the wiring
yourself using jacks and adapters (available at your
local RadioShack store or onlin e at
RadioShack.com), or have the telephone company
update the wiring for you. You must use compatible
modular jacks that are compliant with Part 68 of
FCC Rules. The USOC number of the jack to be
installed is RJ11C (RJ11W for a wall plate).
On a Desk Top
1. Plug one end of
the supplied long
modular cord into
TEL LINE jack
the
on the base’s
back.
2. Plug the modular
cord’s other en d
into a modular
telephone line jack.
3. Insert the supplied AC adapter’s barrel plug
into the
DC IN 9V jack on the back.
4. Route the adapter’s cord through the hook on
the back.
5. Plug the adapter into a standard AC outlet.
CONNECTING, CHARGING AND
R
EPLACING THE BATTERY PACK
The phone comes with a rechargeable Ni-Cd
(nickel-cadmium) battery pack installed in the
handset, but not connected. Before using your
phone, you must connect the battery pack. Then
charge it for about 24 hours.
1. Press down and slide off the battery pack
compartment cover.
!
CAUTION
You must use a
Class two power
!
source that supplies
9V DC and delivers at least
350 mA. Its center tip must
be set to positive and its
plug must fit the phone's
IN 9V
jack. The supplied
adapter meets these
specifications. Using an
adapter that does not meet
these specifications could
damage the phone or the
adapter.
IMPORTANT
!
The EPA
certified
®
RBRC
Battery
Recycling Seal
on the nickelcadmium (Ni-Cd) battery
indicates RadioShack is
voluntarily participating in
an industry program to
collect and recycle these
batteries at the end of their
useful life, when taken out
of service in the United
States or Canada. The
RBRC program provides a
convenient alternative to
placing used Ni-Cd
batteries into the trash or
the municipal waste stream,
which may be illegal in your
area. Please call 1-800THE-SHACK (1-800-843-
7422) for information on NiCd battery recycling and
disposal bans/restrictions in
your area. RadioShack’s
involvement in this program
is part of the company’s
commitment to preserving
our environment and
conserving our natural
resources.
DC
!
Installation
7
Page 8
2. Lift the battery pack out of the compartment.
IMPORTANT
!
Be sure the battery pack is
properly connected before
you try to charge it. The
CHARGE/IN USE indicator
lights when the handset is
on the base even if the
battery pack is not
connected properly.
Ô NOTES Ô
• If the phone does not
work, recharge the
battery pack. (The
Installation
battery power might be
too low for the display to
operate.)
• If the battery pack
becomes weak during a
call, the handset beeps
and
Low Battery
flashes. When this
happens, you cannot
make a call on the
phone until you recharge
the battery pack.
• If the battery pack is
completely discharged
or the base loses power
while the handset is
away from it, place the
handset on the base to
change the digital
security code.
WARNING
o
Dispose of the old battery
pack promptly and properly.
Do not burn or bury it.
There is a risk of explosion
if battery is replaced by an
incorrect type. Dispose of
used batteries according to
the instructions.
!
o
3. Plug the battery pack’s
connector into the socket
in the compartment. The
connector fits only one
way.
4. Put the battery pack in
the compartment.
5. Replace the cover.
To charge the battery pack, place the handset on
the base, face up. The base’s
indicator lights.
Recharge the battery pack when Low Battery
flashes.Ô
When you first use the phone after charging or
recharging the battery pack, the phone might not
work and you might hear error beeps. If this
happens, place the handset to the base to change
the digital security code.
Using a damp cloth, clean the charging contacts on
the handset about once a month.
About once a month, fully discharge the battery
pack by keeping the handset off the base until
Battery
loses its ability to fully recharge.
The supplied battery pack should last about a year.
If the battery pack does not hold a charge for more
than two hours after an overnight charge, replace it
with a new 3.6V, 600 mAh battery pack with a
connector that fits the socket in the battery
compartment. You can order a replacement battery
pack through your local RadioShack store (or online
at RadioShack.com). Install the new battery pack
and charge it for about 24 hours.
If you have trouble replacing the battery pack, take
the phone to your local RadioShack for assistance.
!
flashes. Otherwise, the battery pack
CHARGE/IN USE
o
Low
8
Page 9
SETTING MENU OPTIONS
There are five setup options: AutoTalk, CIDCW
(Caller ID on Call Waiting), Area Code, Dial Mode
and Language.
AutoTalk allows you to answer the phone without
pressing the TALK/FLASH button. If the phone rings
when AutoTalk is on, simply remove the handset
from the base and the phone automatically answers
the call. If the phone rings when AutoTalk is off, you
must press
Changing the Auto Talk and CIDCW
1. Press and hold CID/MENU.
TALK/FLASH to answer the call.
2. Use
3. Press
VOL or VOL to move the pointer to
the selection that you would like to change.
Press
REMOTE/SELECT to toggle between On
and Off.
END and return the handset to the base
unit to complete the setting. The handset
returns to the standby mode.
Entering your Area Code
If you enter a three-digit area code number in the
Area Code option, your local area code does not
appear in Caller ID messages. Do not program this
option, if your calling area requires ten-digit dialing.
When reviewing Caller ID messages, you will see
only the local seven digit number. For calls received
from outside your local area code, you will see a full
ten-digit number.
1. When the phone is in the standby mode, press
and hold
2. Press
3. Press
CID/MENU.
VOL twice to select Area Code.
REMOTE/SELECT.
Installation
9
Page 10
Ô NOTES Ô
Entering your Area Code
When the area code has
already been stored in
memory, the stored area
code will be displayed. To
change it, use the
DELETE
and number keys
to enter the new area code.
Then press
SELECT
tone sounds.
To complete the setting,
press
handset to the base unit.
Installation
Choosing the Dial Mode
• Make sure your battery
pack is fully charged
before choosing the
dialing mode.
• If you are not sure of
your dialing system,
make a trial call. If the
call connects, leave the
setting as is, otherwise
set for pulse dialing.
• If your phone system
requires pulse dialing
and you need to send
the standard tones for
certain situations during
a call, you may “switchover” to tone dialing
(Refer to “Tone Dialing
Switch-over” on page
12).
REMOTE/
. A confirmation
END or return the
CH/
4. Use the number keys (
0 to 9) or CH/DELETE to
enter the three-digit area code. Ô
5. Press
REMOTE/SELECT. A confirmation tone
sounds and the displayed area code is entered.
6. Press
END or return the handset to the base
unit to complete the setting. The handset
returns to the standby mode.
Choosing the Dial Mode
Most phone systems use tone dialing which sends
standard tones through the phone lines. However,
some phone systems still use pulse dialing such as
in rural areas. The default setting is tone dialing.
Depending on your dialing system, set the mode as
Ô
follows:
1. When the phone is in the standby mode, press
and hold
2. Press
3. Press
CID/MENU.
VOL three times to select Dial.
REMOTE/SELECT to toggle between
Tone and Pulse.
4. Press
END or return the handset to the base
unit to complete the setting. The handset
returns to the standby mode.
Setting the Language
1. When the phone is in the standby mode, press
and hold
2. Press
3. Press
(English),
CID/MENU.
VOL four times to select Language.
REMOTE/SELECT to select from Eng
Fr. (French) and Esp (Spanish).
10
4. Press
END or return the handset to the base
unit to complete the setting. The handset
returns to the standby mode.
Page 11
OPERATION
MAKING AND RECEIVING CALLS
Even when you turn off the base’s ringer, you can
still make or receive calls using this phone.
Telephones on the same line and the handset (if its
ringer is not turned off) still ring when there is an
incoming call.
Action Handset On Base Handset Off Base
Press TALK/FLASH,
any number, /TONE/
< or #/> (Auto Talk:
On) or press TALK/
FLASH (Auto Talk:
Off).
1)Press TALK/FLASH.
2)Listen for the dial
tone.
3)Dial the number.
OR
Dial the number. Then
press TALK/FLASH.
1)Press TALK/FLASH.
2)Listen for the dial
tone.
3)Press PAUSE/
REDIAL.
OR
Press PAUSE/
REDIAL. Then press
TALK/FLASH.
To
receive
a call
To
make a
call
To
hang
up
To
redial
Pick up the handset
(Auto Talk: On),
pick up the handset
and press TALK/
FLASH (Auto Talk:
Off).
1)Pick up the handset.
2)Press TALK/FLASH.
3)Listen for the dial
tone.
4)Dial the number.
1)Pick up the handset.
2)Dial the number.
Then press TALK/
FLASH.
Press END or return the handset to the base
(Auto Standby).
1)Pick up the handset.
2)Press TALK/FLASH.
3)Listen for the dial
tone.
4)Press PAUSE/
REDIAL.
1)Pick up the handset.
2)Press PAUSE/
REDIAL. Then press
TALK/FLASH.
Ô or
OR
OR
Ô NOTE Ô
Refer to “Setting Menu
Options” on page 9 to turn
on the Auto Talk feature if
desired.
Operation
11
Page 12
Ô NOTES Ô
Earpiece Volume
When you press
Maximum mode or
in Low mode, an error tone
sounds.
Tone Dialing Switch-over
• The tone feature only
applies when the dial
mode is set to pulse.
• This special number can
be stored in a memory
location. This is referred
to as Chain Dialing (See
“Chain Dialing” on page
Operation
17).
VOL in
VOL
ADJUSTING THE HANDSET RINGER
AND EARPIECE VOLUME
Handset Ringer Tone and Volume
Press VOL or VOL repeatedly in standby mode
to select one of five ringer tones and volume
combinations.
Earpiece Volume
Press VOL or VOL repeatedly during a call to
change the earpiece volume of the handset. This
setting will remain in effect after the telephone call
has ended.Ô
Temporarily Mute the Handset Ringer
If the handset is off the base, simply press END to
temporarily mute the incoming ring. The ringer will
sound with the next incoming call.
REDIAL
The PAUSE/REDIAL key redials the last number
dialed. The redialed number can be up to 32 digits
long.
TONE DIALING SWITCH-OVER
Some telephone companies use equipment that
requires pulse dialing (sometimes referred to as
rotary dialing). If you need to enter tone dialing
digits, you can switch-over to tone dialing during the
call. For example, entering your bank account
number after you have called your bank. Ô
12
Initially make your call with the pulse dialing mode.
Once your call connects, press
desired number. These digits will be sent as tone
dialing. Once the call ends, the tone mode is
canceled and pulse dialing mode resumes.
/TONE/<. Enter the
Page 13
TRAVELING OUT-OF-RANGE
During a call, as you begin to move your handset
too far from your base unit, noise increases. If you
pass the range limits of the base unit, your call will
terminate within one minute.
SELECTING A DIFFERENT CHANNEL
If you encounter interference while using your
phone, you can manually change the phone’s
channel for clear operation. This function works
only when the phone is in use.
Press CH/DELETE. Scanning appears on the
display, indicating the phone is changing to another
channel.
Memory Dialing
PAGE
To locate the handset (while it’s off the base), press
PAGE on the base. The handset beeps for 60
seconds.
Paging is canceled when pressing any handset key,
PAGE on the base or the handset is returned to the
base. Ô
FLASH AND CALL WAITING
If you have “Call Waiting” service and a call waiting
tone sounds while you are on a call, press TALK/
to accept the waiting call. There is a short
FLASH
pause. Then you will hear the new caller. To return
to the original caller, press
TALK/FLASH again.Ô
MEMORY DIALING
STORING PHONE NUMBERS AND
N
AMES
Memory Dialing allows you to dial a number using
just a few key presses. Your phone stores up to ten
names/numbers in the handset. Ô
Ô NOTES Ô
Page
Paging is also canceled
when the phone receives
an incoming call.
Flash and Call Waiting
You must subscribe
through your local
telephone company to
receive Call Waiting
Service.
Storing Phone Numbers
and Names
In memory dialing
operation, you must press a
key within 30 seconds.
Otherwise, an error tone will
sound and the phone will
return to standby.
If you return the handset to
the base, the phone will
also return to standby.
13
Page 14
1. Press
MEM. Select Memory is displayed.
Memory Dialing
2. Press
VOL or VOL, or enter a number (0-
9) to select the memory location where you
would like to store the number.
3. Press
4. Press
MEM or REMOTE/SELECT.
MEM or REMOTE/SELECT. A cursor
flashes indicating that the display is ready for
the name to be entered.
If Edit MemoryXX appears, the selected
memory location is already stored. Then you
must either edit the entry in this location, delete
the entry in this location, or select
Go Back to
choose another location.
5. To enter a name (up to 13 characters), use
number keys.
• See “Steps for Entering Names and Special
Characters” on page 15.
• Use #/
> and /TONE/< to move the cursor to
the desired location.
• Use
CH/DELETE to delete characters as
needed.
• Press and hold
CH/DELETE to delete all the
characters.
14
• If a name is not required, go to step 6.
6. Press
MEM or REMOTE/SELECT. Store
Number is displayed.
The cursor flashes indicating that the display is
ready for the number to be entered.
7. Use the number keys to enter the phone
number.
The phone number cannot exceed 20 digits.
Page 15
• Use
PAUSE/REDIAL to enter a pause in the
dialing sequence. The display shows a P.Ô
Each pause counts as one digit and
represents a two second delay of time
between the digits as they are sent.
CH/DELETE to delete digits as needed.
• Use
8. Press
MEM or REMOTE/SELECT. Y ou will hear a
confirmation tone. Memory storage is
complete. For example, if you store a name and
number into memory location number 01, the
display shows
After about two seconds, the Select Memory
screen is displayed.
Repeat steps 2 - 8 to store more numbers.
Memory01 Stored.
Ô NOTE Ô
The pause feature is useful
for long distance calling,
credit card dialing, or
sequences that require a
pause between digits.
Memory Dialing
9. Press
END to return to standby mode.
STEPS FOR ENTERING NAMES AND
S
PECIAL CHARACTERS
Refer to the letters on the number keys to select the
desired characters.
With each press of a numeric key, the displayed
character appears in the following order:
Upper case letters first, lower case letters next, and
finally the number corresponding to the key.
15
Page 16
Memory Dialing
If You Make a Mistake while Entering
a Name
Use /TONE/< or #/> to move the cursor to the
incorrect character, press
the wrong entry. Then enter the correct character. To
delete all characters, press and hold CH/DELETE.
CH/DELETE to erase up to
Ô NOTE Ô
If the next character uses
the same number key, you
must press
cursor over. Otherwise the
next time you press the
number key, it changes the
character that was
previously set.
#/> to move the
For example, to enter John; Ô
1. Pick up the handset. Press
2. Enter a number or press
MEM.
VOL or VOL to
select a memory location number.
3. Press MEM or REMOTE/SELECT.
4. Press
MEM or REMOTE/SELECT. (When there is
information already stored in the selected
memory location,
Edit MemoryXX is
displayed. See “Editing a Stored Name and/or
Phone Number” on page 17.)
5. Press
6. Press
7. Press
8. Press
9. When finished, press
5 once.
6 six times.
4 five times.
6 five times.
MEM or REMOTE/SELECT.
To continue to store the telephone number, proceed
to step 7 under “Storing Phone Numbers and
Names” on page 14.
16
MAKING CALLS WITH MEMORY
D
IALING
Memory Dialing from Standby Mode
1. Press MEM. The handset displays your
programmed memory locations.
Page 17
2. Press
VOL or VOL, or enter a number (0-
9) to select the memory location you would like
to dial. Ô
3. Press
T ALK/FLASH. Talk and the volume
setting appear on the display. Then the
displayed number is dialed.
Memory Dialing from Talk Mode
1. Press TALK/FLASH. Talk and the volume
setting appears.
2. Press MEM.
3. Press VOL or VOL, or enter a number (0-
9) to select the memory location of the desired
phone number. If you press
REMOTE/SELECT,
the number is dialed.
4. To hang up, press
END.
CHAIN DIALING
The memory locations on the handset are not
limited to phone numbers. You can also store a
group of numbers (up to 20 digits) that you need to
enter once your call connects. This is referred to as
Chain Dialing.
An example of this is a bank account number. Once
you have called your bank, and are prompted to
enter the account number, press
the location number where the special number has
been stored. Then press
REMOTE/SELECT.
MEM and select
Ô NOTES Ô
• If you press
SELECT
FLASH
the name and the
number stored in the
selected memory
location.
• To exit the memory
function without dialing,
press
returns to standby.
• Whenever you are using
a memory menu screen,
you must press a key
within 30 seconds or the
phone will return to
standby.
REMOTE/
before TALK/
, you can confirm
END. The handset
Memory Dialing
Store your special number with an identifying name.
(See “Storing Phone Numbers and Names” on
page 13.)
EDITING A STORED NAME AND/OR
P
HONE NUMBER
1. Press MEM. Select Memory is displayed.
2. Press
9) to select the memory location you would like
to edit, and press
VOL or VOL, or enter a number (0-
MEM or REMOTE/SELECT.
17
Page 18
The screen appears with the memory location
number that you have selected in the display.
Memory Dialing
3. Press
MEM or REMOTE/SELECT.
4. Press VOL or VOL to select Edit
MemoryXX
SELECT
. Then press MEM or REMOTE/
.
Store Name is displayed. The cursor flashes
indicating that the display is ready for the name
to be edited. When a name has not been
stored, the cursor appears at the beginning of
the second line.
5. Use the number keys,
DELETE
to edit the name. (See “Storing Phone
Numbers and Names” on page 13.) To edit only
the phone number, skip this step.
6. Press
MEM or REMOTE/SELECT.
The cursor flashes indicating that the display is
ready for the number to be edited.
7. Use the number keys, /TONE/<, #/>, PAUSE/
REDIAL
or CH/DELETE to edit the phone
number.
The phone number cannot exceed 20 digits.
If you don’t want to change the phone number,
skip this step.
/TONE/<, #/>, or CH/
18
8. Press MEM or REMO TE/SELECT. If y ou changed
either name or phone number, a confirmation
display shows up. If it is correct, press
VOL
to select Yes and press REMOTE/SELECT. You
hear a confirmation tone. The memory storage
is complete.
For example, if you store a name and number
into memory location number 01, the display
Memory01 Stored. After about two
shows
seconds, Select Memory screen is displayed.
9. Press
END to return to standby mode.
Page 19
ERASING A STORED NAME AND
P
HONE NUMBER
1. Press MEM. Select Memory is displayed.
2. Press
9) to select the memory location you would like
to erase.
3. Press
The screen appears with the memory location
number that you have selected in the display.
4. Press
5. Press
VOL or VOL, or enter a number (0-
MEM or REMOTE/SELECT.
MEM or REMOTE/SELECT.
VOL to move the pointer down to
Delete MemoryXX.
6. Press
7. Press
8. Press
9. After about two seconds the display returns to the
MEM or REMOTE/SELECT. The
confirmation screen appears.
VOL to move the pointer to Yes.
REMOTE/SELECT or CH/DELETE. You
hear a confirmation tone.
Select Memory screen. Y ou may delete the
information in another memory location (return to
step 2) or press
END to return to standby mode.
TESTING STORED EMERGENCY
N
UMBERS
If you store an emergency service’s number (police
department, fire department, ambulance) and you
choose to test the stored number, make the test call
during the late evening or early morning hours to
avoid peak demand periods. Also, remain on the
line to explain the reason for your call.
Memory Dialing
19
Page 20
Memory Dialing
ONE-TOUCH SPEED DIAL
You can store your most frequently dialed number
in the One-touch Speed Dial location. The Onetouch Speed Dial allows you to dial a number with
one key press. (There is no need to press
. The phone will automatically dial the
FLASH
number stored.)
TALK/
Ô NOTES Ô
Storing and Editing the
Speed Dial
Number stored in Speed
Dial is independent from the
number stored in Memory
dialing.
Making Calls with the
Speed Dial
If the Speed Dial does not
have a stored number, the
handset will beep rapidly
and the phone will not dial.
STORING AND EDITING THE SPEED
D
IAL
1. When the phone is in the standby mode, press
and hold
If the selection screen appears, there is a
number already stored. Press
to select
SELECT
2. Store the number by following step 7 under
“Storing Phone Numbers and Names” on page
14.
3. Press
You hear a confirmation tone, and memory
storage is complete.
SPEED DIAL. Ô
VOL or VOL
Edit Number. Then press REMOTE/
.
REMOTE/SELECT.
MAKING CALLS WITH THE SPEED
DIAL
When the phone is in the standby mode, simply
SPEED DIAL. The number stored in the Speed
press
Dial memory location is instantly dialed. Ô
DELETING THE SPEED DIAL
1. When the phone is in the standby mode, press
and hold
SPEED DIAL.
20
2. Press
Number
3. Press
VOL or VOL to select Delete
.
REMOTE/SELECT.
Page 21
4. Press
VOL to move the pointer to Yes.
5. Press
REMOTE/SELECT or CH/DELETE.
6. You hear a confirmation tone. After about two
seconds, the handset returns to standby mode.
CALLER ID
You must subscribe to Caller ID service to use
this feature.
When the telephone rings, the Caller ID feature
allows you to view the caller’s name and phone
number on the display before you answer the
phone.
The handset displays the phone number of the
incoming call, the name, and time. Additionally, you
can dial the displayed number and store the
information for memory dialing. Make sure you have
turned on the Caller ID on Call Waiting feature.
(See “Changing the Auto Talk and CIDCW” on page
9.)
WHEN THE TELEPHONE RINGS
1. When the Caller ID message is received, the
display shows the caller’s phone number along
with the date and time. The incoming call
information is stored in the Caller ID record. If
the Caller ID service includes the caller’s name,
the caller’s name appears on the display (up to
15 letters).Ô
You may receive any one of the following
messages:
Message Display
When invalid data is
received
When a private name
is received
“Incomplete Data”
“Private Name”
Ô NOTES Ô
Caller ID
• If you answer a call
before the Caller ID
message is received
(Example: before the
second ring), the Caller
ID message will not
appear.
• When the call is
received via a telephone
company that does not
offer Caller ID service,
the caller’s phone
number and name do
not appear.
(This includes
international calls.)
• When the call is via a
private branch exchange
(PBX), the caller’s phone
number and name may
not appear.
• Data errors appe ar as “ ”.
21
Page 22
Ô NOTES Ô
Viewing the Caller ID
Message List
• In Caller ID operation, if
no key is pressed for
more than 30 seconds,
an error tone sounds
and the telephone
Caller ID
returns to the standby
mode.
• If a call comes in via a
telephone system that
does not offer Caller ID
service, no information is
stored.
• Each message can be
up to 15 characters for
the phone number and
the name.
• The number of calls from
the same Caller ID
appears next to the
received time. Once you
read the new message,
the number will be
cleared and disappear.
Deleting Information from
the Caller ID List
While using the
or Delete
All?
Message?
is pressed for more than 30
seconds, an error tone
sounds and the telephone
returns to standby.
screen if no key
Delete
Message Display
When a private
number is received
When an unknown
name is received
When an unknown
number is received
“Private Number”
“Unknown Name”
“Unknown Number”
2. When you pick up the phone, the display
changes to Talk. (Auto Talk feature is set to
on.)
VIEWING THE CALLER ID MESSAGE
L
IST
The Caller ID list stores information for up to 30
incoming calls - even unanswered calls. Ô
1. Press
CID/MENU.
The summary screen appears. This screen
shows the number of new messages and total
messages.
2. Press
VOL or VOL to display the latest or
oldest Caller ID message.
3. Press
press
4. Press
VOL to see the next message. Or
VOL to see previous message.
END to return to standby mode.
DELETING INFORMATION FROM
THE CALLER ID LIST
The phone stores up to 30 messages. If the phone
receives the 31st message, the oldest one in the li st
is automatically deleted. Caller ID data can also be
deleted manually. Ô
22
Page 23
Deleting a Caller ID Message
1. Press
2. Press
3. Press
4. Press
CID/MENU. Display the message to be
deleted from the Caller ID list by pressing
or VOL.
VOL
CH/DELETE.
VOL or VOL to select Yes or No.Ô
REMOTE/SELECT or CH/DELETE.
When the pointer is at
Yes:
You hear a confirmation tone and the Caller ID
message is deleted.
The next Caller ID message is then displayed.
When the pointer is at
No:
The display returns to the Caller ID message.
Ô NOTESÔ
Deleting a Caller ID
Message
If you get an incoming call
or page, the deleting
operation is canceled and
you can answer the call or
page.
Calling a Party from the
Caller ID List
You cannot make a call
from the Caller ID list if your
phone is connected to a
private branch exchange
(PBX).
Deleting all Caller ID Names/Numbers
1. Press CID/MENU.
2. Press
3. Press
4. Press
CH/DELETE.
VOL or VOL to select Yes or No.
REMOTE/SELECT or CH/DELETE.
When the pointer is at
Yes:
You hear a confirmation tone and all stored
Caller ID messages are deleted.
When the pointer is at
No:
The display returns to the summary screen.
USING THE CALLER ID LIST
Calling a Party from the Caller ID List
You can place a call from the Caller ID list. The
phone stores up to 30 messages.Ô
1. Press
CID/MENU. Select the phone number that
you want to dial by pressing
VOL or VOL.
Caller ID
23
Page 24
2. Press
TALK/FLASH. The displayed phone
number dials automatically.
You can also place a call from Talk Mode.
1. Press TALK/FLASH. Then press CID/MENU.
2. Select the phone number that you want to dial
by pressing the
VOL or VOL.
Ô NOTES Ô
Long Distance Calls and
Area Code Setting/
Caller ID
Cancellation
When a long distance call
has been set,
the display.
Storing Caller ID
Messages in Memory
Dialing
• You can not store a
Caller ID message if no
phone number appears
in the message.
• If a message has
already been stored in
the selected memory
number location, a
confirmation screen is
displayed. Press
to select
REMOTE/SELECT to
overwrite. The display
returns to the Caller ID
list.
Yes. Press
1 appears in
VOL
3. Press
REMOTE/SELECT. The displayed phone
number will be dialed.
Long Distance Calls and Area Code
Setting/Cancellation
Pressing 1 while the incoming Caller ID information
is displayed will place or remove the prefi x 1 in the
display to set up for a long distance call or cancel.
Pressing
3 will set or cancel an area code setting. Ô
Storing Caller ID Messages in Memory
Dialing
Messages shown in the Caller ID list can be stored
in memory dialing.
Using the incoming call information (i.e., Caller ID
list), the phone number of the party on the Caller ID
list can be stored in memory.
1. Press
2. Press
3. Press
4. Press
CID/MENU.
Select the phone number to be stored from the
Caller ID list by pressing
MEM.
VOL and VOL or enter a number (0-
9) to select the memory location to be stored.
REMOTE/SELECT. Ô
VOL or VOL.
24
You hear a confirmation tone and the number is
stored in memory.
The display returns to the Caller ID list.
Page 25
THE INTEGRATED
ANSWERING DEVICE
The phone has a built-in answering system that
answers and records incoming calls. You can also
use your answering system to record a
conversation, leave a voice memo message, or to
announce a special outgoing message to callers
when you’re away from your phone.
FEATURES
• Digital Tapeless
Recording
• 13 minutes of
Recording Time
• Call Screening
• Selectable Outgoing
Messages
• Voice Prompts for
Guidance
(Tri-lingual
Announcement
Option)
Digital Tapeless Recording allows you to quickly
review, save, or delete the messages you choose.
You will never have to worry about a tape wearing
out, jamming, or resetting improperly.
The Integrated Answering System is easy and
convenient to use, but please read through all of
the instructions carefully.
• Time and Day
Announcement
• Remote Message
Retrieval (From
Touch-tone Phone or
your handset)
• Toll Saver
• Conversation
Recording
• Voice Memo
The Integrated Answering Device
25
Page 26
The Integrated Answering Device
Ô NOTES Ô
• For your convenience,
voice prompts will guide
you through the menu
mode.
• After the setting, press
(
PLAY/STOP) to exit
the menu mode, or
MENU/CLOCK to move to
the next menu option.
TURNING THE ANSWERING SYSTEM
O
N/OFF
1. To turn the answering system on, press
ANSWER.
“Answering system is on” and the current
greeting message will be played and you will
hear a confirmation tone. The message
counter displays the number of messages
stored in memory. If the display flashes, there
are new messages waiting for you.
2. To turn the answering system off, press
ANSWER again. After the announcement
“Answering system is off” the message counter
display will no longer be illuminated.
SETTING UP YOUR ANSWERING
S
YSTEM
Using the Menu Mode
The Menu mode allows you to set the following
Answering System functions. Ô
• To scroll through the
menu options, repeatedly
press
MENU/CLOCK. The
system returns to standby
after the last menu option.
You hear a confirmation
tone to indicate standby
mode.
• If any of the following
occurs during menu
setup, the system returns
to standby; you will have
to start over with the
procedure you were
performing.
TALK/FLASH is pressed
-
MENU/CLOCK
MENU/CLOCK
MENU/CLOCK
MENU/CLOCK
MENU/CLOCK
MENU/CLOCK
MENU/CLOCK
26
Page 27
- (PLAY/STOP) is pressed
- Ten seconds elapse without a key press
- An incoming call is received
• If the system remains idle for about five
seconds after the announcement, the system
returns to standby. Once or
/VOL/SEL is
pressed, the idle time is extended to ten
seconds.
Setting the Time
The clock on the answering system starts when
power is supplied to the base. Follow these steps to
set the clock to the correct time. Ô
1. Press
2. Press
3. Press
4. Press
MENU/CLOCK.
The system announces “Time”, the current time
and the guidance for setting the time.
/VOL/SEL or /VOL/SEL until the
correct day is announced. The numbers [ ]
through [ ] are displayed on the base.
SET to select the day.
/VOL/SEL or /VOL/SEL until you hear
the correct hour setting. The numbers [ ]
through [ ] are displayed on the base.
Ô NOTES Ô
• Normally the idle time for
the menu mode is ten
seconds before the
system returns to
standby. However for
setting the time, the idle
time is extended to two
minutes.
• Press and hold
or /VOL/SEL to
SEL
quickly scroll through the
numbers on the display.
/VOL/
5. Press
6. Press
SET to select the hour.
/VOL/SEL or /VOL/SEL until you hear
the correct minute setting. The numbers [ ]
through [ ] are displayed on the base.
7. Press
8. Press
SET to select the minute.
/VOL/SEL or /VOL/SEL until you hear
the correct AM or PM setting. The message
counter displays [ ] or [ ].
9. Press
SET to select the AM/PM setting.
The Integrated Answering Device
27
Page 28
Ô NOTE Ô
The PIN code is set to “80”
when you purchase your
phone.
You hear a confirmation tone. Then the
announcement “Time” and the day and time are
announced for your review. After a few seconds, the
system announces “To set security code, press
menu again”.
Setting a Personal Security Code (PIN)
To play your messages from a remote location, you
need to enter a two-digit Personal Identification
Number (PIN) code (01-99). To select a PIN,
perform the following steps: Ô
1. Press
MENU/CLOCK twice in standby mode.
“Security code” and the current PIN code is
announced as it is displayed on the base.
Then the system announces the guidance for
setting the PIN code.
The Integrated Answering Device
28
2. Press
/VOL/SEL or /VOL/SEL until the
desired number appears.
3. Press
SET to select the PIN code. You hear a
confirmation tone. Then the announcement
“Security code” and the new PIN code is
announced. After a few seconds, the system
announces “To set ring time, press menu
again”.
Setting the Ring Time
The ring time setting allows you to set the number
of rings the caller hears before your answering
system plays the outgoing message. You can set
the ring time to answer after two, four, or six rings.
Set to (Toll Saver) so the answering system
picks up after two rings if you have new messages,
and after four rings if there are none. This way, if
you make a long distance call to check your
messages, you can hang up after the second ring to
avoid billing charges.
Page 29
1. Press MENU/CLOCK three times in standby
mode.
You hear “Ring time” and the current ring time
([ ] two , [ ] four, [ ] six, [ ] T oll sa ver), and it
is displayed on the base. Then you hear the
guidance for setting the ring time.
2. Press
/VOL/SEL or /VOL/SEL until the
desired ring time appears.
3. Press
SET to select the new ring time. You hear
a confirmation tone. Then the announcement
“Ring time” and the new ring time is
announced. After a few seconds, the system
announces “To set record time, press menu
again”.
Selecting the Message Record Time
You have three record time options. The options
one minute” or “four minutes” set the duration for
“
recording the incoming messages. “
answers the call with the preset greeting or your
personal greeting but prevents the caller from
leaving a message.
1. Press
MENU/CLOCK four times in standby
mode.
You hear “Record time” and the current
recording time ([ ] one minute, [ ] four
minutes, [ ] Announce only, No recording),
and it is displayed on the base. Then you hear
the guidance for setting the record time.
2. Press
/VOL/SEL or /VOL/SEL until the
desired time appears.
3. Press
SET to select the new recording time.
You hear a confirmation tone. Then the
announcement “Record time” and new
recording time is announced. After a few
seconds, the system announces “To set
message alert, press menu again”.
Announce only”
The Integrated Answering Device
29
Page 30
The Integrated Answering Device
Announce only feature
The announce only feature plays a prerecorded
outgoing message “Hello, no one is available to
take your call. Please call again.”, and it will not
allow the caller to leave a message. To set
“Announce only”, follow the previous steps. The
outgoing message automatically switches to
announce only message.
To scroll between the prerecorded message or your
own personal greeting, press
outgoing message is played. If you want to use your
own greeting, or want to change your greeting to
omit the prompt “to leave a message”, refer to
“Recording a personal outgoing message”
(Greeting) on page 32.
Setting the Message Alert Tone
Message Alert feature lets you know you have new
messages by sounding a short beeping tone. When
the system receives a new message while the
Message Alert is on, the alert tone sounds every 15
seconds.
1. Press MENU/CLOCK five times in standby
mode.
You hear “Message alert” and the current
setting ([ ] Off or [ ] On), and it is displayed
on the base. Then you hear the guidance for
setting the message alert tone.
OGM when the
30
2. Press
or [ ].
3. Press
confirmation tone. Then the announcement
“Message Alert” and the current setting you
have selected is announced. After a few
seconds, the system announces “To set
language, press menu again”.
/VOL/SEL or /VOL/SEL to select [ ]
SET to select the new setting. You hear a
Page 31
Turning the Message Alert tone Off.
• When all new messages are played back, the
Message Alert tone will automatically
deactivate.
OR
• If you want to silence the alert before you finish
listening to all the new messages, press any
key on the base unit and the tone will
automatically deactivate.
Turning Message Alert tone Off when you’re away
from your phone.
• When all new messages are played back using
the remote playback feature (see “Remote
Operation” on page 37) the Message Alert tone
will automatically deactivate. The tone will not
deactivate until all messages are played back.
After all new messages are played back, when
a new message is received, Message Alert
tone will activate.
Selecting the Language
The answering system voice announcements can
be heard in English, French or Spanish.
To choose the language of the answering system
voice announcements:
1. Press
MENU/CLOCK six times in the standby
mode.
You hear the announcement “Language,
English” followed by the guidance for setting
the language. The current setting ([ ] (English),
[ ] (French) or [ ] (Spanish)) appears on the
base.
2. Press
/VOL/SEL or /VOL/SEL to select the
desired language.
The Integrated Answering Device
31
Page 32
Ô NOTES Ô
• You can record a
greeting more than two
seconds up to 30
seconds long.
• Position yourself as near
to the base’s
The Integrated Answering Device
microphone as possible
and speak clearly when
recording your outgoing
message.
• See “Selecting the
Message Record Time”
on page 29 on how to
set the announce only
feature.
• To delete the personal
Greeting, press
(
DELETE) during the
announcement and the
system announces
“Greeting has been
deleted”.
3. Press
SET. A confirmation tone is heard along
with the setting in the language selected.
SETTING YOUR OUTGOING
M
ESSAGE (GREETING)
When you receive a call, the answering system
automatically plays either a preset message or your
own greeting.
Preset message
The following message is prerecorded:
“Hello, no one is available to take your call. Please
leave a message after the tone.”
Recording a personal outgoing message
(Greeting)
1. Press and hold
You hear the announcement “Record Greeting”
and a confirmation tone. [ ] flashes on the
message counter.
2. Start recording your message. You have 30
seconds, and the message counter starts to
count down [ ] to [ ] every second.
3. When you are finished recording your greeting,
OGM, (PLAY/STOP) or SET. You hear a
press
confirmation tone. Then your greeting plays
back for you.
Choosing between the two outgoing
messages
OGM. Then press OGM again when the
Press
outgoing message is played. This switches between
the prerecorded greeting or the personal greeting.
After finishing playing back the message, a
confirmation tone is heard.
OGM in standby mode. Ô
32
Page 33
Setting the base ringer volume
You have three ringer options. One allows you to
turn the ringer off. The other two are volume levels.
You can change the ringer volume while in standby
mode or the incoming call is ringing. Ô
1. Press
RINGER.
You hear the ringer at the current volume level
([ ] High, [ ] Low, [ ] Off) (if you set the base
ringer volume to off, “Ringer off” is announced
in standby mode.) and it is displayed on the
base.
Ô NOTE Ô
Although you have set the
base ringer to off, you will
still hear the ringer from the
handset on the base.
2. Press
RINGER repeatedly until the desired
ringer option appears.
3. The system displayed new ringer volume.
Temporarily Mute the Base Ringer and the Call
Screen
Press (
PLAY/STOP) to temporarily mute the
incoming ring. This also mutes the caller's message
being recorded (Call Screen). The ringer and the
Call Screen will be heard with the next incoming call.
The base ringer mute is canceled when pressing
RINGER.
The Call Screen mute is canceled when pressing
/VOL/SEL or /VOL/SEL.
Adjusting the speaker volume level
You can adjust the volume of the base speaker by
pressing the
Press
/VOL/SEL or /VOL/SEL on the base.
/VOL/SEL for louder or /VOL/SEL for
softer during the base speaker is being used except
for menu mode. The base speaker volume also
applies the Call Screen.
The numbers [ ]-[ ]are displayed on the base
indicating the volume levels. [ ] being the softest
and [ ] being the loudest.
The Integrated Answering Device
33
Page 34
Ô NOTES Ô
• When the answering
system is full, [ ] is
displayed on the base,
and the system
announces “No
remaining time”. You
should delete some
messages so that the
system can record new
messages.(Refer to
“Deleting a message” on
page 35.)
• To stop playing your
messages, press
(
PLAY/STOP) again at
any time.
The Integrated Answering Device
USING YOUR ANSWERING SYSTEM
The message counter displays the number of
messages stored in memory. If the display flashes,
there are new messages waiting for you. The
flashing number represents the number of new
messages, not total messages. This phone is
designed to play your new messages first. After you
play all your new messages, you can then play your
old messages. Ô
Playing your messages
1. Press (
The system announces the number of new and
old messages. The LED displays the number of
new messages, and the number flashes. The
day and time that each message was received
are announced after the message is played.
The message counter displays the number of
current messages stored.
When all new messages have been played,
you hear a confirmation tone and an
announcement “End of messages”. The
system returns to standby.
2. After you have reviewed all of your new
messages, you can play your old messages by
pressing (
have listened to a new message, it becomes an
old message. The old messages will be played
in the order in which they were received.
Repeating a message
1. Press (
The number of stored messages are announced.
2. To repeat the current message, press after a
few seconds of begi nn i n g th e me ssa ge. To
repeat the previous message, press within a
few seconds (about four seconds during
remote operation) after a message begins
playing. If you hav e sev eral messages, press
repeatedly until you return to the message you
want to replay. If the current message is the
first new message, the system plays bac k from
the beginning of the current message (it does
not go back into the old message group).
PLAY/STOP) in standby mode.
PLAY/STOP) again. Once you
PLAY/STOP) to review y our messages.
34
Page 35
3. Press (PLAY/STOP) at any time to stop
reviewing messages and return to standby . The
message counter shows the number of
messages stored in memory.
To quickly scroll backwards through a message,
press and hold .
Skipping a message
1. Press (
PLAY/STOP) to review your
messages. The number of messages is
announced.
2. Press at anytime to skip to the next
message.
Each time is pressed, the system scans
forward one message. If you hav e several
messages, press repeatedly to find the
message you want to play.
3. Press (
PLAY/STOP) at any time to stop
reviewing your messages and return to
standby. The message counter shows the
number of messages stored in memory.
To quickly scroll forward through a message, press
and hold .
Deleting a message
To maintain maximum record time, delete the old
messages.
1. Press (
PLAY/STOP) to review your
messages.
2. Press
(DELETE) anytime during the message
to delete. Ô
3. You hear a confirmation tone and the message
is deleted.
You can also delete all the messages.
1. Press
(DELETE) in standby mode.
Ô NOTE Ô
When you press
(
DELETE), you are
permanently deleting the
message. Once deleted,
the message cannot be
replayed.
The Integrated Answering Device
35
Page 36
Ô NOTES Ô
Voice memo
• The voice memo
recorded is completely
independent of the
greeting message.
• The voice memo
messages are recorded
as incoming messages.
Recording a conversation
• A recorded conversation
is treated as a incoming
message and will be
added to the stored
messages.
• When recording a
conversation, all dialing
features except for using
call waiting (See “Flash
and Call Waiting” on
page 13.) are disabled.
Stop recording if you
need to enable any other
handset keys.
• If you receive a call
The Integrated Answering Device
waiting tone while
recording a
conversation, press
TALK/FLASH to accept
the waiting call. The
recording feature
continues recording the
new call. The original
call is put on hold.
IMPORTANT
!
Every state has different
regulations governing the
recording of conversations
over the telephone. Be sure
to check your local, state
and federal laws before
using this product to record
any telephone conversation
in order to determine that
your use is in compliance
with such laws or guidelines.
You hear an announcement “To delete all
messages, press delete again”.
2. Press
(DELETE) again.
You hear a confirmation tone and [ ] is
displayed on the base. All the messages are
deleted.
When you try to delete all messages without first
listening to your new messages, you hear several
short beeps followed by an announcement “Please
playback all messages”. This protects you from
accidentally erasing messages you have not yet
reviewed.
Voice memo
The voice memo function allows the user to record
messages (more than two seconds up to four
minutes). Ô
1. Press and hold
MEMO REC.
You hear an announcement “Record memo
message” and a tone. [ ] flashes on the
message counter.
2. Start your recording.
3. When you have finished, press (PLAY/STOP),
MEMO REC or SET to stop recording. You hear a
confirmation tone and the system returns to
standby.
Recording a conversation
!
You can record up to ten minutes of conversation
while you are using your phone. Any conversation
that lasts less than two seconds will not be
recorded.
Ô !
1. During a conversation from the handset, press
and hold
MEMO REC. The unit begins recording
and [ ] flashes on the message counter.
36
Page 37
A beep that can be heard by both parties
sounds during recording.
2. To stop recording, press (PLAY/STOP) or
MEMO REC. You hear a confirmation tone.
REMOTE OPERATION
Remote access away from home
You can operate your answering system from a
remote location using any touch-tone telephone.
Use this function to check for recorded messages,
to play or delete message. When using any touchtone telephone, you can even record a new greeting
message.
1. Call your telephone number.
Ô NOTE Ô
Once you enter the remote
access menu, you must
enter a command within 15
seconds,or the answering
system automatically hangs
up and returns to standby.
2. During the greeting message, press
0 and
enter your PIN code. (See “Setting a Personal
Security Code (PIN)” on page 28.)
3. The answering system announces the current
time and the number of messages stored in
memory. Then you hear “To play incoming
message, press
02. For help, press 10”.
4. You may continue to listen to the Voice
Prompts, or you may select a command from
the following chart. Ô
Command Function
0 and 1 Repeat a Message
0 and 2 Playing Incoming Messages
0 and 3 Skipping a Message
0 and 4 Deleting a Message
0 and 5 Stop Operation
0 and 6 Answering System On
0 and 7 Memo Record/Stop*
0 and 8 Greeting Message Record/Stop*
0 and 9 Answer System Off
1 and 0 Voice Prompts
The Integrated Answering Device
37
Page 38
The Integrated Answering Device
*For Memo Record and Greeting Message Record
function, the first time you enter the corresponding
command, it starts the Recording function. If you
want to stop the recording, enter the command
again.
5. After all of the Voice Prompts have played, you
hear intermittent beeps indicating that the
system is in the command waiting mode. You
may enter another command at this time from
the chart.
6. When you are finished, hang up to exit the
system. The answering system automatically
returns to standby.
Turn on the answering system remotely
If you have forgotten to turn on your answering
system, you can turn it on remotely from any touchtone telephone.
1. Call your telephone number.
2. Wait ten rings until the system answers. You
hear intermittent beeps.
38
3. Press
0. And then enter your PIN code. The
answering system announces the current time
and the number of messages stored in
memory. You hear “T o play incoming message,
02. For help, press 10”.
press
4. Press
0. And then 6 to turn the answering
system On. You hear the outgoing message
and a confirmation tone.
5. Hang up the phone and subsequent calls will
be answered by the system.
Page 39
Remote access with the handset
You can operate your answering system from
another room using a handset. Ô
1. With the phone in standby mode, press
REMOTE/SELECT on the handset. Remote
AnsweringMachine operation
appears
on the display. The answering system
announces the current time and the number of
messages stored in the memory.
2. You hear "To play incoming message, press
For help, press
0." You hear intermittent beeps.
3. Enter a command within 15 seconds. You may
select a command from the following chart:
Command Function
/1 Repeat a Message
/2 Play Incoming Messages
/3 Skip a Message
/4 Delete a Message
/5 Stop Operation
6 Answering System On
9 Answering System Off
0 Voice Prompts
4. After the command has finished, you hear
intermittent beeps indicating that the system is
in the command waiting mode. You may enter
another command at this time from the chart on
step 3.
5. When you are finished, press
END to exit the
system. The answering system automatically
returns to standby.
Ô NOTES Ô
• If you press
the base is connected,
the phone will return to
standby.
• If the base is not
connected within five
seconds, you hear
beeps and the phone will
2.
return to standby.
• The base's keypad is
disabled during remote
operation.
• If you receive a call, the
remote operation is
canceled.
• During the remote
operation [--] appears
on the base.
• If you have new
messages and old
messages, only the new
messages will be
played. After you have
reviewed your new
messages, you can play
your old messages by
pressing
END before
/2 again.
The Integrated Answering Device
39
Page 40
Additional Information
ADDITIONAL
INFORMATION
INSTALLING THE OPTIONAL
B
ELTCLIP
To attach the beltclip
Insert the beltclip into the holes on each side of the
handset. Press down until it clicks.
To remove the beltclip
Pull both sides of the beltclip to release the tabs
from the holes.
HEADSET INSTALLATION
You can connect an optional headset with a 3/32inch (2.5-mm) plug. Contact RadioShack for a
suitable headset.
Ô NOTES Ô
• If you place the handset
on the base to recharge
it while the headset is
connected, be sure the
handset seats properly.
• You can use a handset
holder (available from
your local RadioShack
store) to hang the
handset on your belt for
greater convenience
when using a headset.
40
To connect the headset, open the rubber cover on
the side of the handset. Then insert the headset’s
plug into the jack. Ô
When you finish using the headset, disconnect it
from the handset and close the rubber cover to
protect the jack.
Page 41
TROUBLESHOOTING
If your phone is not performing to your expectations, please try these simple
steps first.
Problem Solution
The CHARGE/IN USE
LED won’t illuminate
when the handset is
placed on the base.
The audio sounds weak
and/or scratchy.
Can’t make or receive
calls.
The handset doesn’t ring
or receive a page.
Severe noise
interference.
The Caller ID does not
display.
The answering system
does not work.
Make sure the AC adapter is plugged into the base and wall
outlet.
Make sure the handset is properly seated on the base.
Make sure the charging contacts on the handset are clean.
Move the handset and/or base to a different location a wa y from
metal objects or appliances and try again.
Press CH/DELETE in the Talk mode to help eliminate
background noise.
Make sure that the handset is not too far from the base.
Check both ends of the telephone line cord.
Make sure the AC adapter is plugged into the base and wall
outlet.
Disconnect the AC adapter f or a few minutes. Then reconnect it.
Make sure that the handset is not too far from the base.
The battery pack may be weak. Charge the battery for 24
hours.
The handset may be too far from the base unit.
Place the base unit away from appliances or metal objects.
Keep the handset away from microwave ovens, computers,
remote control toys, wireless microphones, alarm systems,
intercoms, room monitors, fluorescent lights, and electrical
appliances.
Move the base to another location or turn off the source of
interference.
The handset was picked up before the second ring.
The call was placed through a switch board.
Call your local telephone company to verify your Caller ID
service is current.
Make sure the base unit is plugged in.
Make sure the answering system is turned on.
Troubleshooting
41
Page 42
Problem Solution
Set the record time to either the one minute or four minute
Cannot record any
messages.
Messages are
incomplete.
After a power failure, the
outgoing message is
deleted.
No sound on the base
Troubleshooting
unit speaker during call
monitoring or message
playback.
Cannot access remote
call-in features from
another
touch-tone phone.
option.
The memory may be full. Delete some or all of the saved
messages.
The incoming messages may be too long. Remind callers to
leave a brief message.
The memory may be full. Delete some or all of the saved
messages.
Record your personal outgoing message again. The default
message should remain.
Adjust the speaker volume on the base unit.
Make sure you’re using the correct PIN code.
Make sure that the touch-tone phone you’re using can transmit
the tone for at least two seconds. If it cannot, you may have to
use another phone to access your messages.
If you still have problems, disconnect the phone. If other phones on the same line
work properly, the fault is in this phone or its installation. If you cannot find the
problem, take your phone to your local RadioShack store for assistance.
42
Page 43
CARE
Keep the phone dry; if it gets wet, wipe it dry
immediately. Use and store the phone only in
normal temperature environmen ts. Handle the
phone carefully; do not drop it. Keep the phone
away from dust and dirt, and wipe it with a damp
cloth occasionally to keep it looking new.
SERVICE AND REPAIR
If your phone is not performing as it should, take it
to your local RadioShack store for assistance. To
locate your nearest RadioShack, use the store
locator feature on RadioShack’s website
(www.radioshack.com), or call 1-800-The Shack
(843-7422) and follow the menu options. Modifying
or tampering with the phone’s internal components
can cause a malfunction and might invalidate its
warranty and void your FCC authorization to
operate it.
43
Care
Page 44
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for one (1) year from the date of purchase from RadioShack companyowned stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED
HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES,
INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES
CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE
OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT,
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply
to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, unless otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the property of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the prod uct made afte r the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallati on.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
12/99
RadioShack Corporation
Fort Worth, Texas 76102
43-3857
UPZZ01042BZ
02A04
Printed in China
Loading...