Proface LT3300 User Manual

Download

/76HULHV

+DUGZDUH0DQXDO

Preface

Thank you for purchasing Pro-face’s LT3000 Series Graphic Logic Controller Interface (Hereafter referred to as the “LT

unit”).

Before operating your LT unit, be sure to read this manual to familiarize yourself with the LT unit’s operation procedures

and features.

NOTICE

1. Copying this manual’s contents, either in whole or in part, is prohibited without the express permission of Digital

Electronics Corporation, Japan.

2. The information contained in this manual is subject to change without notice.

3. If you should you find any errors or omissions in this document, please contact Digital Electronics Corporation to

report your findings.

4. Please be aware that Digital Electronics Corporation shall not be held liable by the user for any damages, losses,

or third party claims arising from the uses of this product.

Product names used in this manual are the trademarks / registered trademarks of their respective owners.

Essential Safety Precautions

All safety-related procedures stated in this document must be followed to operate the LT correctly and safely. Be sure to

read this and any related documents thoroughly to understand the correct operation and functions of the LT unit.

Safety Icons

Throughout this manual, these icons provide essential safety information for LT operation procedures requiring special

attention. These icons indicate the following levels of danger:

Indicates situations where severe bodily injury, death or major equipment damage can occur.

Indicates situations where slight bodily injury or minor equipment damage can occur.

Indicates actions or procedures that should NOT be performed.

Indicates actions or procedures that MUST be performed to ensure correct unit operation.

System Design

Be sure to design your LT control system so that, in the event of a main power supply failure or a LT

accident, the user system’s overall safety integrity will be maintained. If this is not done, incorrect output

signals or a LT malfunction may cause an accident.

1) Interlock and other circuits designed to interrupt or oppose normal machine movement (such as

Emergency Stop, General Protection, and forward and reverse rotation), as well as those designed to

prevent machine damage (such as upper, lower, and traverse movement limit positioning) should all be

designed to be located outside of the LT.

2) When the LT generates a “Watchdog Timer Error,” during logic program operating, the logic program

operation will halt. Also, when Errors occur in Input/Output control areas that the LT cannot detect,

unexpected movement may occur in those areas. Therefore, and to prevent unsafe machine

movement, a “Failsafe Circuit” should be created which is completely external to the LT.

For a failsafe circuit, refer to “4.2.5 Installation Precautions” (page 4-13).

3) If a problem arises with an external unit’s relay or transistor, causing an output (coil) to remain either

ON or OFF, a major accident can occur. To prevent this, be sure to set up external watchdog circuits

that will monitor vital output signals.

Design a circuit that will supply power to the LT unit’s I/O before starting up the LT. If the LT unit’s internal

program enters RUN mode prior to the I/O unit’s load control power turning ON, an incorrect output

(signal) or malfunction could cause an accident.

Design a user program that ensures the safety of the user’s system, in the event of a LT display or control

error, or either a data transmission error or power failure between the LT and a connected unit. These

types of problems can lead to an incorrect output (signal) or malfunction, resulting in an accident.

Do not make switches using the switches on the touch panels which may cause operator injury and

machine damage. An output may remain either ON or OFF and a major accident can occur. To prevent

this, set up circuits such as limiters that will monitor vital output signals. Design switches for important

operations to be performed by separate devices. An incorrect output or malfunction can occur and thereby

cause an accident.

Do not create LT touch panel switches to control machine safety operations, such as an emergency stop

switch. Install these switches as separate hardware switches, otherwise severe bodily injury or equipment

damage can occur.

When using the LT with transportation vehicles (trains, cars, and ships), disaster and crime prevention

devices, various types of safety equipment, and medical devices that are not life-support related, use

redundant and/or failsafe system designs to ensure proper reliability and safety.

Do not use the LT as a warning device for critical alarms that can cause serious operator injury, machine

damage or can halt system operation. Critical alarm indicators and their control/activator units must be

designed using stand-alone hardware and/or mechanical interlocks.

Do not use the LT with aircraft control devices, aerospace equipment, central trunk data transmission

(communication) devices, nuclear power control devices, or medical life support equipment, due to these

devices’ inherent requirements of extremely high levels of safety and reliability.

When using the LT with transportation vehicles (trains, cars, and ships), disaster and crime prevention

devices, various types of safety equipment, and medical devices that are not life-support related, use

redundant and/or failsafe system designs to ensure proper reliability and safety.

After the LT unit’s backlight burns out the touch panel is still active, unlike the LT unit’s “Standby Mode”. If

the operator fails to notice that the backlight is burned out and touches the panel, a potentially dangerous

machine operation error can occur. Therefore, do not create LT unit touch panel switches that may cause

injury and/or equipment damage. If your LT unit’s backlight suddenly turns OFF, use the following steps to

determine if the backlight is actually burned out.

1) If the LT unit’s “Backlight Control” is not set and the screen has gone blank, your backlight is burned

out.

2) If the LT unit’s “Backlight Control” is set to Standby Mode and the screen has gone blank, and touching

the screen or performing another input operation does not cause the display to reappear, your backlight

is burned out.

Handling

Do not disassemble or modify the LT unit. Doing so may cause a fire or an electric shock.

Do not operate the LT in an environment where flammable gases are present, since it may cause an

explosion.

Wiring

To prevent electrical shock or equipment damage, unplug the LT unit’s power cord from the power supply

prior to installing or wiring the LT.

To prevent an electric shock be sure to disconnect your LT unit’s power cord from the power supply before

wiring the LT.

Do not use the voltage not specified in the manual. Doing so may cause a fire or an electric shock.

The cables connected to the LT should be secured by cable clamps to prevent weight or tension of the

cables added to the connectors or terminals.

The LT unit’s wiring should be checked to confirm that both the operating voltage and wiring terminal

locations are correct. If either the voltage or the wiring terminal location is incorrect, it can cause a fire or

accident.

Maintenance

NEVER touch a live power terminal. Doing so could cause an electrical shock or a machine malfunction.

To prevent an electrical shock, unplug the LT unit’s power cord before either cleaning the LT or attaching/

detaching the power terminal attachment screws.

Do not connect or disconnect Host and LT unit communication cables while the LT is turned ON.

Do not replace the LT unit’s battery yourself. The LT uses a lithium battery for backing up its internal clock

data and the battery may explode if it is replaced incorrectly. When replacement is required, please

contact your local LT distributor.

Wiring Layout Precautions

To prevent a LT unit malfunction due to excessive noise, isolate all LT input/output signal lines from all

power wiring or power cables via a separate wiring duct.

Installation

Be sure all cable connectors are securely attached to the LT unit. A loose connection may cause incorrect

input or output signals.

Wiring

Be sure to ground the LT unit’s FG wire separately from other equipment FG lines. Also, be sure to use a

grounding resistance of 100Ω or less and a 2mm

applicable standard. Otherwise, electric shock or malfunctions may result.

Be sure to use only the designated torque to tighten the LT unit’s terminal block screws. If these screws

are not tightened firmly, it may cause a short-circuit, fire or incorrect unit operation.

Be sure that metal particles and wiring debris do not fall inside the LT unit. They can cause a fire,

malfunction or incorrect unit operation.

[0.0062inch2] or thicker wire, or your country’s

Maintenance

Be sure to read the LT unit’s manual carefully before performing program changes, entering forced output,

or using the RUN, STOP, or PAUSE commands while the LT is operating. Mistakes made when using

these items can cause machine accidents or damage.

Be sure the electricity is turned OFF before attaching or detaching an I/O unit. If the electricity is ON when

an I/O unit is attached or detached, damage or malfunction to the I/O unit may occur.

Unit Disposal

When the product is disposed of, it should be disposed of in a manner appropriate to, and in accordance

with, the user country's industrial machinery disposal/recycling standards.

General Safety Precautions

Do not press on the LT unit’s display with excessive force or with a hard object, since it can damage the

display. Also, do not press on the touch panel with a pointed object, such as the tip of a mechanical pencil

or a screwdriver, since doing so can damage the touch panel.

Do not install the LT where the ambient temperature exceeds the specified range. Doing so may cause a

unit malfunction.

To prevent abnormally high temperatures from occurring inside the LT, do not restrict or block the LT unit’s

rear-face ventilation slots.

Do not operate the LT in areas where large, sudden temperature changes can occur. These changes can

cause condensation to form inside the LT, possibly causing it to malfunction.

Do not allow water, liquids or metal fragments to enter inside the LT unit’s case, since they can cause

either a malfunction or an electric shock. The allowable pollution degree is 2.

Do not operate or store the LT in locations where it can be exposed to direct sunlight, high temperatures,

excessive dust, moisture or vibration.

Do not operate or store the LT where chemicals evaporate, or where chemicals are present in the air.

Corrosive chemicals: Acids, alkalines, liquids containing salt

Flammable chemicals: Organic Solvents

Do not use paint thinner or organic solvents to remove dirt or oil from the LT unit’s surface. Instead, use a

soft cloth moistened with a diluted neutral detergent.

Do not use or store the LT in areas with direct sunlight, since the sun’s ultraviolet rays may cause the

LCD’s quality to deteriorate.

Do not store the LT in an area where the temperature is lower than that recommended in the LT unit’s

specifications. Doing so may cause the LCD display’s liquid to congeal, which can damage the LCD.

Also, if the storage area’s temperature becomes higher than the specified level, the LCD’s liquid may

become isotropic, causing irreversible damage to the LCD. Therefore, only store the LT in areas where

temperatures are within the LT unit’s specifications.

After turning OFF the LT, be sure to wait for 5 seconds before turning it ON again. The LT may not operate

correctly if it is restarted too quickly.

Be sure to back up the LT screen data and logic programs in case they are lost accidentally.

LCD Panel Usage Precautions

• The LCD panel’s liquid contains an irritant. If the panel is damaged and any of this liquid contacts your skin, immedi-

ately rinse the area with running water for at least 15 minutes. If the liquid gets in your eyes, immediately rinse your

eyes with running water for at least 15 minutes and consult a doctor.

• The LT unit’s LCD screen may flicker or show unevenness in the brightness of certain images or at some contrast set-

tings. This is an LCD characteristics and not a product defect.

• There’s an individual difference in brightness and tone of LCD screen. Please be aware of this difference before using

the lined-up plural units.

• Depending on the ambient temperature, LCD displays may sometimes look whitish (at high temperatures) or blackish

(at low temperatures). This is an LCD characteristic and not a product defect.

• Some of LT unit's LCD screens may contain light or dark pixels. This is an LCD characteristic and not a product

defect.

• Extended shadows, or “Crosstalk” may appear on the sides of screen images. This is an LCD characteristic and not a

product defect.

• The color displayed on the LT unit’s LCD screen may appear different when seen from outside the specified viewing

angle. This is an LCD characteristic and not a product defect.

• When the same image is displayed on the LT unit’s screen for a long period, an afterimage may appear when the image

is changed. This is an LCD characteristic and not a product defect.

• To prevent an afterimage:

* Set the LT unit’s display OFF feature when you plan to display the same screen image for a long period of time.

* Change the screen image periodically and try to not display the same image for a long period of time.

• Please be aware that characteristics of the LT unit's LCD screen with a white LED backlight may change gradually

owing to the deterioration of the backlight LED and the LCD display may look bluish.

This manual uses the following icons:

Information Symbols

Indicates a warning or a product limitation. Be sure to follow the instructions given with

Screen Editor Indicates the GP-Pro EX software.

PLC Abbreviation for Programmable Logic Controller.

Logic program Indicates a ladder program created with the GP-Pro EX.

* Indicates useful or important supplemental information.

SEE

this icon to ensure the safe operation of the LT.

Contains additional or useful information.

Indicates pages containing related information.

About the Manuals

For the detailed information on LT3000 Series, refer to the following manuals.

• Maintenance/Troubleshooting

For the Offline Settings, see Maintenance/Troubleshooting (Offline Settings Guide).

• GP-Pro EX Device/PLC Connection Manual

• GP-Pro EX Reference Manual

• LT specifications may change when optional items are used. Check the optional

item installation guides’ specifications for variances, if any.

The manuals can be downloaded from Pro-face Home Page, “Otasuke Pro!”.

“Otasuke Pro!” URL

http://www.pro-face.com/otasuke/

Model name

LT 3

* ** - * 1 -

AB C ED

LT3000 Series Model Name Indication

***

D D24 DC type power supply is used.

2 LT-3200 series (3.8-inch): QVGA (320 x 240 dots)

3 LT-3300 series (5.7-inch): QVGA (320 x 240 dots)

00 Standard machine

01 Low-cost machine

A Monochrome Amber/ Red LCD

L Monochrome LCD

S STN color LCD

T TFT color LCD

K Sink output type

C Source output type

LT3000 Series Model Names

The term “LT3000” Series refers to the following LT model numbers:

Series Model Product No.

LT3000 series LT-3200 series LT-3201A

LT-3300L

LT-3300S

LT-3300 series

LT-3300T

LT-3301L

LT3201-A1-D24-K LT3201-A1-D24-C

LT3300-L1-D24-K LT3300-L1-D24-C

LT3300-S1-D24-K LT3300-S1-D24-C

LT3300-T1-D24-K LT3300-T1-D24-C

LT3301-L1-D24-K LT3301-L1-D24-C

Global Code

A global code is assigned to every Pro-face product as a universal model number.

For more information on product models and their matching global codes, please refer to the following URL.

http://www.pro-face.com/product/globalcode.html

Package Contents

The following items are included in the LT unit’s package. Before using the LT, please check that all items listed here are present.

LT Unit: 1

• Installation Guides (Set of Japanese/Set of English)

• Warning/Caution Information (1)

• EX Module Hardware Manual (in Japanese/ in English) (1)

(LT-3200 series)

Installation Gasket: 1

(Attached to the LT unit)

DC Power Connector: 1

USB Cable Clamp: 1 set

Holder: 1, Cover: 1

Installation Fasteners: 4

per set

(LT-3300 series)

DIO Connector 1

(LT-3200 series) (LT-3300 series)

EX Module*1 Securing Hook (LT-3300 series only) 1

*1 The EX module can be used as an expansion I/O unit for the LT3000 series or as a remote I/O unit

(supported by the CANopen board type unit of the GP3000 series). Read the included manual before using the EX module.

This unit has been carefully packed, with special attention to quality. However, should you find anything damaged or missing, please contact your local LT distributor immediately.

• UL listed products

Installation prerequisites for standards

Industrial Control Equipment refer to UL508

Suitable for use in Class I, Division 2, Groups A, B, C, and D Hazardous (classified) locations, or Non-Hazardous Locations.

• c-UL listed products

Standard for Process Control Equipment

Suitable for use in Class I, Division 2, Groups A, B, C, and D Hazardous (classified) locations, or Non-Hazardous Locations.

• Product List

Product Model No.

LT3201-A1-D24-K 3481401-01 99

LT3201-A1-D24-C 3481401-02 99∗199

LT3300-T1-D24-K 3583401-01 9999

Registration

Model No.

see [a] in the

“Product List“

refer to ANSI/ISA-12.12.01

refer to CSA-C22.2 No.142

refer to CSA-C22.2 No.213

see [b] in the

“Product List“

see [c] in the

“Product List“

see [d] in the

“Product List“

UL c-UL

[a] [b] [c] [d]

∗1

LT3300-T1-D24-C 3583401-02 9999

LT3300-S1-D24-K 3583401-01 99

LT3300-S1-D24-C 3583401-02 99∗299

LT3300-L1-D24-K 3583401-11 99∗299

LT3300-L1-D24-C 3583401-12 99∗299

LT3301-L1-D24-K 3583401-13 99∗299

LT3301-S1-D24-C 3583401-14 99∗299

*1 This unit with revision code "B" or later are all compliant this standard. *2 This unit with revision code "1" or later are all compliant this standard.

For the detailed certification's information, refer to the Pro-face Home page.

∗2

UL/c-UL File No.E220851, E210412

Be aware of the following items when building the LT into an end-use product:

• The LT unit’s rear face is not approved as an enclosure. When building the LT unit into an end-use product, be sure to

use an enclosure that satisfies standards as the end-use product’s overall enclosure.

• The LT unit must be used indoors only.

• Install and operate the LT with its front panel facing outwards.

• If the LT is mounted so as to cool itself naturally, be sure to install it in a vertical panel. Also, it’s recommended that

the LT should be mounted at least 100 mm away from any other adjacent structures or machine parts. The temperature

must be checked on the final product in which the LT is installed.

• For use on a flat surface of a Type 4X (Indoor Use Only) and/or Type 13 Enclosure.

(1) Suitable for use in Class I, Division 2, Groups A, B, C, and D Hazardous Locations, or Non-Hazardous

Locations.

(2) WARNING: Explosion hazard-substitution of any components may impair compliance to Class I,

Division 2.

(3) WARNING: Explosion hazard-when in hazardous locations, turn the power OFF before replacing or

wiring modules.

(4) WARNING: Explosion hazard-do not disconnect equipment unless power has been switched off or the

area is known to be Non-Hazardous.

(5) In the case of use in Hazardous Locations, be sure to check that the externally connected unit and each

interface have been fixed with screws and locked. In Hazardous Locations, it’s impossible to insert or

pull the cable from the applicable port. Be sure to check that the location is Non-Hazardous before

inserting or pulling it.

The safety certificate can be downloaded from Pro-face Home Page. Home Page URL

http://www.pro-face.com/

*1The compliant Rev. with Hazardous Locations are as follows.

LT-3300T : all Rev.

LT-3300S, LT-3300L, LT-3301L : Rev.1

SEE

About Revision (page 12)

CE Marking

㌂G㣿G㧦G㞞G⌊GⶎG

G 㧊G ₆₆⓪G 㠛ⶊ㣿Oh PG 㩚㧦䕢㩗䞿₆₆⪲㍲G 䕦ⰺ㧦G ⡦⓪G ㌂㣿㧦⓪G 㧊G㩦㦚G㭒㦮䞮㔲₆G ⹪⧒ⳆSGṖ㩫㣎㦮G 㰖㡃㠦㍲G㌂㣿䞮⓪G ộ㦚G⳿㩗㦒⪲G䞿┞┺UG

G G

The following units are CE marked products complying with the EMC Directive.

LT3201-A1-D24-K LT3201-A1-D24-C LT3300-S1-D24-K LT3300-S1-D24-C LT3300-T1-D24-K LT3300-T1-D24-C LT3300-L1-D24-K LT3300-L1-D24-C LT3301-L1-D24-K LT3301-L1-D24-C

For the detailed information on CE Marked, be downloaded and refer the Declaration of Conformity from Pro-face Home Page. Home Page URL http://www.pro-face.com/

KC Markings

㌂㣿㧦㞞⌊ⶎG

₆G㫛G⼚G

h G₆₆G

O㠛ⶊ㣿G⹿㏷䐋㔶₆㧦㨂PG

About Revision

The nameplate on the LT has the revision number of the LT. In the example below, the asterisk, which is placed at the “A”

position, shows that the revision number is “A”.

Preface...................................................................................................................... 1

Essential Safety Precautions..................................................................................... 2

Information Symbols.................................................................................................. 7

About the Manuals .................................................................................................... 7

LT3000 Series Model Name Indication ..................................................................... 8

LT3000 Series Model Names .................................................................................... 8

Global Code .............................................................................................................. 8

Package Contents..................................................................................................... 9

Installation prerequisites for standards.................................................................... 10

CE Marking.............................................................................................................. 12

KC Markings............................................................................................................ 12

About Revision ........................................................................................................ 12

Contents ................................................................................................................. 13

Chapter 1 Overview

1.1 System Design................................................................................................ 1-2

1.1.1 LT-3200 Series......................................................................................................1-2

1.1.2 LT-3300 Series......................................................................................................1-4

1.2 Accessories .................................................................................................... 1-6

1.2.1 USB Host Interface ...............................................................................................1-6

1.2.2 Serial Interface Item..............................................................................................1-6

1.2.3 Option Items .........................................................................................................1-7

1.2.4 Maintenance Items ...............................................................................................1-7

1.2.5 EX Module ............................................................................................................1-8

1.3 Part Names and Functions ........................................................................... 1-10

1.3.1 LT-3200 Series....................................................................................................1-10

1.3.2 LT-3300 Series.................................................................................................... 1-11

Chapter 2 Specifications

2.1 LT-3200 Series................................................................................................ 2-2

2.1.1 General Specifications .......................................................................................... 2-2

2.1.2 Performance Specifications ..................................................................................2-4

2.1.3 Interface Specifications.........................................................................................2-6

2.1.4 Wiring to the DIO Connector...............................................................................2-12

2.1.5 Dimensions .........................................................................................................2-14

2.2 LT-3300 Series.............................................................................................. 2-17

2.2.1 General Specifications ........................................................................................ 2-17

2.2.2 Performance Specifications ................................................................................2-19

2.2.3 Interface Specifications.......................................................................................2-21

2.2.4 Wiring to the DIO Connector...............................................................................2-30

2.2.5 Dimensions .........................................................................................................2-32

Chapter 3 Sample of the Circuit Diagrams

3.1 Examples of Particular I/O Connections ......................................................... 3-2

3.1.1 Connection to Pulse Motor Amplifier (CW/CCW type) ..........................................3-2

3.1.2 Connection to Pulse Motor Amplifier (Clock Up/Down System) ...........................3-4

3.1.3 Connection to a Rotary Encoder...........................................................................3-6

Chapter 4 Installation and Wiring

4.1 Installation....................................................................................................... 4-2

4.2 Wiring Precautions.......................................................................................... 4-7

4.2.1 Connecting the Power Cord..................................................................................4-7

4.2.2 Connecting the Power Supply.............................................................................4-10

4.2.3 Grounding ........................................................................................................... 4-11

4.2.4 Wiring Precautions..............................................................................................4-12

4.2.5 Installation Precautions.......................................................................................4-13

4.3 USB Cable Clamp Attachment/Removal ...................................................... 4-16

4.3.1 LT-3200 Series....................................................................................................4-16

4.3.2 LT-3300 Series....................................................................................................4-17

Chapter 5 Maintenance

5.1 Cleaning the Display ....................................................................................... 5-2

5.2 Periodic Check Points..................................................................................... 5-3

5.3 Replacing the Installation Gasket ................................................................... 5-4

5.4 Replacing the Backlight .................................................................................. 5-6

1 Overview

1. System Design

2. Accessories

3. Part Names and Functions

This chapter describes peripheral devices that can be connected to LT Series units along with the name and

functions of each part.

1-1

LT3000 Series Hardware Manual

1.1 System Design

1.1.1 LT-3200 Series

The following diagram illustrates the standard range of items that can be connected to LT-3200 Series units.

 LT RUN Mode Peripherals

LT Unit

(2)

(3)

(1)

LT Interfaces

USB-Serial (RS-232C) Conversion Cable CA6-USB232-01

USB-to-IEEE1284 Conversion Cable (Commercial type)

USB Cable FP-US00 or commercial type

USB Front Cable (CA5-USBEXT-01)

USB Hub (Commercial type)

EX Module (Up to two EX modules can be connected to the rear side of the LT-3201A.)

Various types of I/O equipment Indicators, LEDs, sensors, switches, and so on

USB Memory Strage (Commercial type)

Bar-Code Reader (Commercial type)

Printer (Commercial type)

1-2

(1) USB Host Interface (2) EX Module Interface (3) DIO Interface

*1 For supported models, refer to Pro-face’s support site “Otasuke Pro!”

(http://www.pro-face.com/otasuke/).

You can connect to this site by clicking the GP-Pro EX’s [Help (H)] menu – [Connect to Support Site-

“Otasuke Pro!” (O)] command.

 Edit Mode Peripherals

LT Unit

Chapter 1 Overview

(1)

USB Transfer Cable CA3-USBCB-01

USB Memory Strage (Commercial type)

USB-Serial (RS-232C) Conversion Cable CA6-USB232-01

RS-232C Cable (Prepared by user)

Modem (Commercial type)

USB Port

Serial Port

Personal Computer (Commercial type)

Telephone lines

LT Interfaces

(1) USB Host Interface

*1 For supported models, refer to Pro-face’s support site “Otasuke Pro!”

(http://www.pro-face.com/otasuke/).

Screen Editor Software

GP-Pro EX

You can connect to this site by clicking the GP-Pro EX’s [Help (H)] menu – [Connect to Support Site-

“Otasuke Pro!” (O)] command.

*2 For details regarding connection methods, be sure to read “Transferring Projects and Data” under

“COM Transfer Connections” in the GP-Pro EX Reference Manual.

*3 Certain types and models of PCs cannot be used

SEE

GP-Pro EX Reference Manual

1-3

LT3000 Series Hardware Manual

1.1.2 LT-3300 Series

The following diagram illustrates the standard range of items that can be connected to LT-3300 Series units.

 LT RUN Mode Peripherals

LT Unit

To an Ethernet Network

(1)

Ethernet Cable(commercial type)

Hub

(commercial type)

(2)

USB-Serial (RS-232C) Conversion Cable CA6-USB232-01

USB-to-IEEE1284 Conversion Cable (Commercial type)

USB Cable FP-US00 or commercial type

USB Front Cable (CA5-USBEXT-01)

USB Hub (Commercial type)

(3)

(4)

(5)

EX Module (Up to 3 EX modules can be connected to the rear side of the LT-3300 series)

Various types of I/O equipment Indicators, LEDs, sensors, switches, and so on

Bar-Code Reader (Commercial type)

RS-232C Cable CA3-CBL232/5M-01

Mouse Emulator (Commercial type)

Bar-Code Reader (Commercial type)

Printer (Commercial type)

USB Memory Strage (Commercial type)

(7)

1-4

(5)

RS-232C Isolation Unit CA3-ISO232-01 Switch setting:RS-232C

(6)

COM Port Conversion Adapter CA3-ADPCOM-01

(6)

RS-232C Isolation Unit CA3-ISO232-01 Switch setting:RS-422

*2,*3

RS-232C Cable CA3-CBL232/5M-01

RS-422 Cable CA3-CBL422/5M-01

Terminal Block Conversion Adapter CA3-ADPTRM-01

RS-422 Cable CA3-CBL422/5M-01

COM Port Conversion Adapter CA3-ADPCOM-01

RS-232C Cable CA3-CBL232/5M-01

RS-422 Cable (Prepared by user)

Terminal Block Conversion Adapter CA3-ADPTRM-01

RS-422 Cable (Prepared by user)

(7)

(8)

Temperature Controllers Various Boards, such as Memory Link

(8)

Chapter 1 Overview

LT Interfaces

(1) Ethernet Interface

(10BASE-T/100BASE-TX)

Temperature Controller (etc.) Interfaces

(7) RS-232C Port (8) RS-422 Port

Not available with LT-3301L units (2) USB Host Interface (3) EX Module Interface (4) DIO Interface (5) Serial Interface (COM1)

(RS-232C mode) (6) Serial Interface (COM1)

(RS-422 mode)

*1 For supported models, refer to Pro-face’s support site “Otasuke Pro!”

(http://www.pro-face.com/otasuke/). You can connect to this site by clicking the GP-Pro EX’s [Help (H)] menu – [Connect to Support Site-

“Otasuke Pro!” (O)] command. *2 The RS-232C Isolation Unit does not correspond to RS-422/485 (2 wire) communication. *3 The RS-232C Isolation Unit does not correspond to Serial Multilink communication.

 Edit Mode Peripherals

LT Unit

(2)

To an Ethernet Network

(1)

USB Transfer Cable CA3-USBCB-01

USB Memory Strage (Commercial type)

USB Port

Serial Port

Personal Computer (Commercial type)

Telephone lines

Screen Editor Software

GP-Pro EX

USB-Serial (RS-232C) Conversion Cable CA6-USB232-01

RS-232C Cable (Prepared by user)

Modem (Commercial type)

LT Interfaces

(1) Ethernet Interface

(10BASE-T/100BASE-TX) Not available with LT-3301L units

(2) USB Host Interface

*1 For supported models, refer to Pro-face’s support site “Otasuke Pro!”

(http://www.pro-face.com/otasuke/).

You can connect to this site by clicking the GP-Pro EX’s [Help (H)] menu – [Connect to Support Site-

“Otasuke Pro!” (O)] command. *2 For details regarding connection methods, be sure to read “Transferring Projects and Data” under

“COM Transfer Connections” in the GP-Pro EX Reference Manual. *3 Certain types and models of PCs cannot be used

SEE

GP-Pro EX Reference Manual

1-5

LT3000 Series Hardware Manual

1.2 Accessories

All accessories listed here are produced by Digital Electronics Corporation.

1.2.1 USB Host Interface

Product Name Model No. Description

USB Transfer Cable CA3-USBCB-01 (2m)

USB Cable FP-US00 (5m) Connects a USB printer. (TYPE-B)

USB Front Cable CA5-USBEXT-01 (1m)

USB-Serial (RS-232C) Conversion Cable

*1 For supported models, refer to Pro-face’s support site “Otasuke Pro!”

(http://www.pro-face.com/otasuke/). You can connect to this site by clicking the GP-Pro EX’s [Help (H)] menu - [Connect to Support Site “Otasuke Pro!” (O)] command.

*2 Requires an RS-232C cable (prepared by user) for connection. For details regarding

system design, refer to  Edit Mode Peripherals (page-3) if using LT-3200; refer to  Edit Mode Peripherals (page-5) if using LT-3300. For instructions on how to connect between USB-Serial (RS-232C) Conversion Cable and your PC, always refer to the "GP-Pro EX Reference Manual -> Transferring Projects and Data -> COM Transfer Connections".

CA6-USB232-01 (0.5m)

Downloads project data created with the Screen Editor via the LT unit’s USB I/F.

Extension cable attaching USB port to front panel.

Cable for converting a LT unit's USB interface into a serial interface (RS-232C). Allows connection to modems barcode readers Can be used to transfer project data created with the Screen Editor via a serial interface.

that support RS-232C.

1.2.2 Serial Interface Item

Product Name Model No. Description

RS-232C Cable CA3-CBL232/5M-01 (5m)

RS-422 Cable CA3-CBL422/5M-01 (5m)

RS-422 Cable CA3-CBL422-01 (5m)

RS232C Isolation Unit

COM Port Conversion Adapter

Terminal Block Conversion Adapter

CA3-ISO232-01

CA3-ADPCOM-01

CA3-ADPTRM-01

Interface cable for communication between a temperature controller/various boards and the LT-3300 series via RS-232C.

Interface cable for communication between a temperature controller/various boards and the LT-3300 series via RS-422. (Socket Type)

Interface cable for communication between a temperature controller/various boards and the LT-3300 series via RS-422. (Plug Type)

Unit for providing isolated connection between a temperature controller/various boards and the LT-3300 series. RS-232C and RS-422 are switchable.

Connects optional RS-422 communication items to LT-3300 series unit’s COM1 port.

Connects output from a serial interface with an RS-422 terminal block.

1-6

1.2.3 Option Items

Product Name Model No. Corresponding LT Description

Screen Protection Sheet

Proective Cover CA4-DCMDL-01 LT-3300 Series

1.2.4 Maintenance Items

Product Name Model No. Corresponding LT Description

Installation Fastener

Installation Gasket

DIO Connector

USB Cable Clamp

DC Power Supply Connector for Medium-sized Units

EX Module Securing Hook

Panel Cutout Adapter

CA3-ATFALL-01 LT3000 Series

ST400-WP01 LT-3200 Series

CA3-WPG6-01 LT-3300 Series

CA6-DIOCN4-01 LT-3200 Series

CA7-DIOCN5-01 LT-3300 Series

CA5-USBATL-01 LT-3200 Series

CA7-USBAT6-01 LT-3300 Series

CA5-DCCNM-01 LT3000 Series

CA7-FIXEXM-01 LT-3300 Series

CA4-ATM5-01 LT-3300 Series

Chapter 1 Overview

CA6-DFS4-01 LT-3200 Series Disposable, dirt-resistant sheet

CA3-DFS6-01 LT-3300 Series

for the LT unit’s screen. (5 sheets/set) (Hard type)

The installation of the cover is to protect Display from leaking liquid and raise resistant performance against chemical substance (5 sheets)

Used to install the LT into a solid panel.

Provides dust and moisture resistance when LT is installed into a solid panel.

Connector attached to the DIO interface. Connects an external I/O device. (Set of 5 connectors)

USB Cable clamp to prevent disconnection.

Connector for attaching power supply to medium-sized units.

Hook for securing three EX modules to the LT-3300 Series.

Panel cutout adapter for mounting LT3300 Series in cutout of LT Series.

1-7

LT3000 Series Hardware Manual

1.2.5 EX Module

(Expanded I/O Unit for LT3000 Series use)

Up to two EX modules can be connected to the rear side of the LT-3200 series.

Up to three EX modules can be connected to the rear side of the LT-3300 series.

• As for EXM-DMM24DRF and EXM-ARI8LT, only one EX module can be connected to an LT.

For the details, please read “EX Module Hardware Manual” downloaded from Pro-face's support

site “Otasuke Pro!” (http://www.pro-face.com/otasuke/).

Standard Input Module

Product Name Model No. Description

EX module (8-point input module) EXM-DDI8DT

EX module (16-point input module) EXM-DDI16DT

Standard Output Module

Product Name Model No. Description

EX module (8-point relay-output module)

EX module (16-point relay-output module)

EX module (8-point sink-output module)

EX module (8-point source-output module)

EX module (16-point sink-output module)

EX module (16-point source-output module)

8-point sink/source shared I/O Unit. DC24V input signal can be connected.

16-point sink/source shared I/O Unit. DC24V input signal can be connected.

EXM-DRA8RT

EXM-DRA16RT

EXM-DDO8UT 8-point transistor output sink I/O Unit.

EXM-DDO8TT

EXM-DDO16UK 16-point transistor output sink I/O Unit.

EXM-DDO16TK

8-point relay output/2 common type I/O Unit.

16-point relay output/2 common type I/O Unit.

8-point transistor output source I/O Unit.

16-point transistor output source I/O Unit.

Standard I/O Module

EX module (4-point inputs/4-point relay-output module)

EX module (16-point inputs/8-point relay-output module)

1-8

Product Name Model No. Description

EXM-DMM8DRT

EXM-DMM24DRF

4-point input sink-source/4-point relayoutput/1 common type I/O Unit.

16-point input sink-source/8-point relay-output/1 common type I/O Unit.

Analog Input Module

Product Name Model No. Description

EX module (2-ch analogue-input module)

EX module (4-ch Analog input / Temperature input module)

EX module (8-ch Pt100/Pt1000 input module)

Analog Output Module

Product Name Model No. Description

EX module (1-ch analogue-output module)

EX module (2-ch analogue-output module)

EXM-AMI2HT

EXM-AMI4LT

EXM-ARI8LT

EXM-AMO1HT

EXM-AVO2HT

Chapter 1 Overview

2-ch analogue Input Unit. (Voltage DC0 to 10V / Current DC4 to 20mA)

4-ch temperature Input Unit. (Voltage DC0 to 10V / Current DC4 to 20mA) Pt100/Pt1000/Ni100/Ni1000

8-ch temperature Input Unit. Pt100/Pt1000

1-ch analogue Output Unit. (Voltage DC0 to 10V / Current DC4 to 20mA)

2-ch analogue Output Unit. (Voltage DC-10 to +10V )

Analog I/O Module

Product Name Model No. Description

EX module (Thermocouple Pt100 input/1-ch analogue-output module)

EX module (2-ch analogue-input/1-ch analogue-output module)

EX module (4-ch analogue-input/2-ch analogue-output module)

EXM-ALM3LT

EXM-AMM3HT

EXM-AMM6HT

2-ch temperature Input/1-ch analogue Output Unit. Pt100 Input (Voltage Output DC0 to 10V / Current Output DC4 to 20mA)

2-ch analogue Input/1-ch analogue Output Unit. (Voltage I/O DC0 to 10V / Current I/O DC4 to 20mA)

4-ch analogue Input/2-ch analogue Output Unit. (Voltage I/O DC0 to 10V / Current I/O DC4 to 20mA)

1-9

LT3000 Series Hardware Manual

1.3 Part Names and Functions

1.3.1 LT-3200 Series

A: Status LED

This LED indicates the LT’s status, e.g. power

input, firmware RUN status or backlight condition. Also, indicates the status of logic program execution.

Color Indicator

Front

Green

Red

Orange

Flashing

ON When power is turned on.

Flashing

ON Backlight burnout

Flashing During software startup

Operation

Mode

(Drawing)

OFFLINE -

operation

Logic execu-

tion mode

(when logic is

enabled)

RUN

STOP

Major Error

B: AUX Unit Interface/Expansion Unit (EXT2)

Interface where additional units such as communication devices can be connected.

C: EX Module Interface (EXT1)

This is the interface to mount the Pro-face’s EX module.

D: Power Plug Connector

1-10

Back

E: USB Host Interface (USB)

Conforms to USB1.1. (TYPE-A conn.) Power Supply Voltage: DC5V ± 5% Output Current: 500mA (at maximum) Connects a data transfer cable or USB-compatible printer. The maximum communication distance is 5m.

F: DIO Interface (DIO)

This is the interface to mount external I/O equipment using the DIO connector.

Bottom

1.3.2 LT-3300 Series

Front

Right side

Chapter 1 Overview

A: Status LED

This LED indicates the LT’s status, e.g. power input, firmware RUN status or backlight condition. Also, indicates the status of logic program execution.

Logic execu-

tion mode

(when logic is

enabled)

RUN

STOP

Major Error

Color Indicator

Green

Flashing

ON When power is turned on.

Red

Orange

Flashing

ON Backlight burnout

Flashing During software startup

Operation

Mode

(Drawing)

OFFLINE -

operation

B: DIO Interface (DIO)

This is the interface to mount external I/O equipment using the DIO connector.

C: AUX Unit Interface/Expansion Unit (EXT2)

Interface where additional units such as communication devices can be connected.

D: EX Module Interface (EXT1)

This is the interface to mount the Pro-face’s EX module.

E: Power Plug Connector F: Ethernet Interface

(10BASE-T/100BASE-TX)

The Ethernet transmission interface (10BASE-T/ 100BASE-TX). An RJ-45 type modular jack connector (8-pole) is used. The LED turns on or off to indicate the current status.

Back

Bottom

LED Indicates

Green ON Data transmission available

Green OFF

Yellow ON

Yellow OFF No data transmission

G: USB Host Interface (USB)

Conforms to USB1.1. (TYPE-A conn.)

No connection or subsequent transmission failure

Data transmission is occurring.

Power Supply Voltage: DC5V ± 5% Output Current: 500mA (at maximum) Connects a data transfer cable or USB-compatible printer. The maximum communication distance is 5m.

H: Serial Interface (COM1)

RS232C/RS422/RS485 serial interface. D-sub 9pin plug type connector. Communication method is switched via software.

1-11

LT3000 Series Hardware Manual

1-12

2 Specifications

1. LT-3200 Series

2. LT-3300 Series

This chapter describes the general, functional and interface specifications of the LT as well as its part names

and dimensions.

2-1

LT3000 Series Hardware Manual

2.1 LT-3200 Series

2.1.1 General Specifications

 Electrical Specifications

Input Voltage DC24V

Rated Voltage DC19.2 to 28.8V

Allowable Voltage Drop 10ms (max.)

Power Consumption 18W (max.)

In-Rush Current 30A (max.)

Power Supply

Voltage Endurance

Insulation Resistance

 Environmental Specifications

AC1000V 20mA for 1 minute

(between charging and FG terminals)

DC500V 10MΩ (min.)

(between charging and FG terminals)

Surrounding Air Temperature

Storage Temperature -20 to +60°C

Ambient Humidity

Storage Humidity

Dust 0.1mg/m

Physical

Pollution Degree For use in Pollution Degree 2 environment

Atmosphere Free of corrosive gases

Air Pressure Vibration Resistance (availment altitude)

Vibration Resistance

Mechanical

Concussion Resistance

Noise Immunity

Electrical

Electrostatic Discharge Immunity

*1 Extended use in environments where surrounding air temperature is 40°C or higher

(Wet bulb temperature: 39°C max. - no condensation.)

(2000 meters above sea-level and below)

5 to 9Hz single-amplitude 3.5mm

9 to 150Hz constant-accelerated velocity 9.8m/s

X, Y, Z directions for 10 cycle (100 minute)

(147m/s2 X, Y, Z directions for 3 time)

6kV (complies with EN 61000-4-2 Level 3)

0 to +50°C

10 to 90% RH

and below (non-conductive levels)

800 to 1114hPa

IEC61131-2 compliant

Noise Voltage: 1000V

Pulse Duration: 1µs

Rise Time: 1ns

(via noise simulator)

P-P

2-2

may degrade the display quality and result in decreased contrast.

 Structural Specifications

Grounding

Structure

Cooling Method Natural air circulation

Installation

Weight Approx. 1.0kg [2.2lb] max. (unit only)

External Dimensions W130.0mm [5.12in] X H104.0mm [4.09in] X D76.5mm [3.01in]

Panel Cut Dimensions

*1 The front face of the LT unit, installed in a solid panel, has been tested using

conditions equivalent to the standards shown in the specification. Even though the

LT unit’s level of resistance is equivalent to these standards, oils that should have no

effect on the LT can possibly harm the unit. This can occur in areas where either va-

Chapter 2 Specifications

Grounding resistance of 100Ω 2mm2 or thicker wire,

or your country’s applicable standard.

(Same for FG and SG terminals)

Rating: Equivalent to IP65f NEMA #250 TYPE 4X/13

(Front surface at panel embedding)

Feature size: All-in-one

Installation configuration: Panel embedding

W118.5mm [4.67in] X H92.5mm [3.64in]

Panel thickness: 1.6mm [0.06in] to 5.0mm [0.20in]

porized oils are present, or where low viscosity cutting oils are allowed to adhere to

the unit for long periods of time. If the LT’s front face protection sheet becomes

peeled off, these conditions can lead to the ingress of oil into the LT and separate

protection measures are suggested.

Also, if non-approved oils are present, it may cause deformation or corrosion of the

front panel’s plastic cover. Therefore, prior to installing the LT be sure to confirm the

type of conditions that will be present in the LT’s operating environment.

If the installation gasket is used for a long period of time, or if the unit and its gasket

are removed from the panel, the original level of the protection cannot be guaran-

teed. To maintain the original protection level, be sure to replace the installation gas-

ket regularly.

*2 As for dimensional tolerance everything +1/-0mm and R in angle are below R3.

2-3

LT3000 Series Hardware Manual

2.1.2 Performance Specifications

 Performance Specifications

Application

Data Backup

Interface

Clock Accuracy

DIO Interface

AUX Interface/ Expansion Unit

USB Host Interface

EX Module Interface

FLASH EPROM 6MB

SRAM 128K byte

Used lithium battery for backup memory

The interface to external I/O equipment

Input/Output points: 12-point inputs, 6-point outputs

Connector: 22 pins

Interface for external additional unit only

(such as communication equipment) (external)

Conforms to USB1.1. (TYPE-A conn.) x 1

Power Supply Voltage: DC5V ±5%

Output Current: 500mA (max.)

Communication Distance: 5m (max.)

Interface for Pro-face’s EX Modules

(Up to two EX modules can be connected)

± 65 seconds/ month (at room temperature)

Variable Area 64 KB SRAM (uses lithium battery)

Program Area 132 KB FLASH EPROM

Control Memory

*1 It is user active capacity.

*2 The LT’s internal clock has a slight error. At normal operating temperatures and con-

ditions, with the LT operating from its lithium battery, the degree of error is 65 seconds

per month. Variations in operating conditions and battery life can cause this error to

vary from -380 to +90 seconds per month. For systems where this degree of error will

be a problem, the user should be sure to monitor this error and make adjustments

when required.

• When the message “RAAA051 Low battery” is displayed, supply power to the display

unit and fully charge the battery. The battery charges within 24 hours to a level which

allows backup operation. Completing a full charge requires about 96 hours (4 days).

• A Lithium battery’s lifetime is: 10 years when the battery’s ambient temperature is 40°C

or less. 4.1 years when the battery’s ambient temperature is 50°C or less. 1.5 years when

2-4

the battery’s ambient temperature is 60°C or less.

When used for backup:

Approximately 100 days, with a fully charged battery.

Approximately 6 days, with a half-charged battery.

Chapter 2 Specifications

 Display Specifications

Display Type Monochrome Amber/ Red LCD

Resolution W320 x H240 pixels

Dot pitch W0.24mm [0.01in] x H0.24mm [0.01in]

Effective Display Area W78.8mm [3.10in] x H59.6mm [2.35in]

Color/Shade level Black and White (8 Shades)

Amber/ Red LED

Backlight

When replacement is required, contact your local LT distributor.)

Brightness control 8 levels of adjustment available via touch panel

Contrast Adjustment 8 levels of adjustment available via touch panel

Display Service Life

Backlight Service Life

Language Fonts

50,000hrs. or more (at 25°C and continuous operation - period until

(Backlight display service life is not included.)

backlight brightness decreases to 50%)

Japanese: 6962 (JIS Standards 1 & 2)

ANK: 158 (Korean, Traditional Chinese

and Simplified Chinese fonts are downloadable.)

(Not user replaceable.

MTBF value: 50,000hrs. (TYP)

(including 607 non-kanji characters)

Character Sizes

Font Sizes

Text composition

8 x 8 dots 40 Char. x 30 rows

8 x 16 dots 40 Char. x 15 rows

Te xt

16 x 16 dots 20 Char. x15 rows

32 x 32 dots 10 Char. x 7 rows

*1 Font sizes other than those above can be set up by software.

 Touch Panel Specifications

Type Resistive Film (analog)

Resolution 1024 x 1024

Service Life 1,000,000 times or more

Standard font: 8X8, 8X16, 16X16 and 32X32 dot fonts

Stroke font: 6 to 127dot fonts

Standard font: Width can be expanded up to 8 times.

Height can be expanded up to 8 times

2-5

LT3000 Series Hardware Manual

2.1.3 Interface Specifications

This section describes the specifications of each interface of the LT Series unit.

 DIO Interface (Connector)

• When preparing the cable to connect the wiring, check the pin numbers inscribed

on the DIO Connector.

Applicable connector

Pin Arrangement Pin No. Signal Name Pin No. Signal Name

A11

(Cable connection side)

B11

• Parenthesized signal names ( ) indicate when Pulse output (PLS*), PWM output

(PWM*), or Counter Input (CT*) are used.

2-1871940-1 <Tyco Electronics AMP.> CA6-DIOCN4-01<Pro-face>

A1 IN1 B1 IN0 (CT0)

A2 IN3 B2 IN2 (CT1)

A3 IN5 B3 IN4 (CT2)

A4 IN7 B4 IN6 (CT3)

A5 IN9 B5 IN8

A6 IN11 B6 IN10

A7 NC B7 COM

A8 0V B8 +24V

A10

A11 OUT5 B11 OUT4

OUT1 (PLS1, PWM1)

OUT3 (PLS3, PWM3)

B10

OUT0 (PLS0, PWM0)

OUT2 (PLS2, PWM2)

2-6

 Input Specifications

Rated Voltage DC24V

Maximum Allowable Voltage DC28.8V

Input Method Sink/Source Input

Rated Current

Input Resistance

Input Derating

Input Points 12

Common Lines 1

Common Design 12 points/1 common line

Operation Range

ON Voltage DC19V or more

OFF Voltage DC5V or less

6.5mA (DC24V) (IN0, IN2, IN4, IN6) 5mA (DC24V) (Other input)

Approx. 3.7kΩ (IN0, IN2, IN4, IN6) Approx. 4.7kΩ (Other input)

SEE



Input Derating (page2-7)

Chapter 2 Specifications

Input Delay

Time

OFF to ON 0.5 to 20ms

ON to OFF 0.5 to 20ms

Input Signal Display No LED indicators

Status Display None

Isolation Method Photocoupler Isolation

External Connection 22-pin connector (used with Output section)

External Power Supply For Signal: DC 24V

*1 In the case of IN0, IN2, IN4, and IN6, the input delay time generates a 5µs-

delay. For example, in the case of a 0.5ms-cycle sampling:

5µs (ON to OFF) + 0.5ms (sampling cycle) + 5µs (OFF to ON) = 0.51ms

A minimum 0.51ms-restriction is imposed on the input pulse width.

In the case of IN1, IN3, IN5, and from IN7 to IN11, the input delay time gen-

erates a 0.5ms-delay. For example, in the case of a 0.5ms-cycle sampling:

0.5ms (ON to OFF) + 0.5ms (sampling cycle) + 0.5ms (OFF to ON) = 1.5ms

A minimum 1.5ms-restriction is imposed on the input-pulse width.

*2 Digital filter can be set at intervals of 0.5 ms.

 Input Derating

Using LT input voltage that exceeds the rated voltage, the input ON voltage, the number of input points or the

LT’s temperature can effect. Also, the LT’s input section could overheat, which could lead to an accident or

malfunction. Refer to the following drawing and perform Input Derating within the LT unit’s rated range.

(%)

100

DC24.0 to DC26.4V

DC28.8V

Input ON Rate

0 10 20 30 40 50 (°C)

Surrounding Operating Temperature

2-7

LT3000 Series Hardware Manual

• Input Circuit

DC 24V

External Power

COM B7

IN11 A6

IN10 B6 IN9 A5 IN8 B5 IN7 A4 IN6 B4 IN5 A3 IN4 B3 IN3 A2 IN2 B2 IN1 A1 IN0 B1

*1 Dotted line shows connection to sink output type.

 Output Specifications

Output Terminal OUT0 to OUT3 OUT4 to OUT5

Rated Voltage DC24V

Allowable Voltage Range DC20.4V to DC28.8V

Output Method

LT3201-A1-D24-K Sink Output

LT3201-A1-D24C

Source Output

Maximum Load Voltage 0.2A/point, 1.2A/common

Output Voltage Drop DC 0.5V or less

0.5ms or less (With output at DC24V, 200mA)

Output Delay Time

OFF to ON

ON to OFF

5µs or less (With output at DC24V, 200mA)

Voltage Leakage (when OFF) 0.1mA or less

Clamp Voltage 39V ± 1V

Type of Output Transistor Output

Common Lines 1

Common Design 6 points/1 common line

External Connection 22-pin connector (also used for Input)

Output Protection Type Output is unprotected

Internal Fuse 2.5A, 125V Chip fuse (not replaceable)

Surge Control Circuit Zener diode

Output Points 6

Output Signal Display No LED indicators

Status Display Element None

Isolation Method Photocoupler Isolation

External Power Supply For Signal: DC 24V

Internal Circuit

2-8

• LT3201-A1-D24-K Output Circuit (Sink type)

Chapter 2 Specifications

+24V B8

Internal Circuit

Fuse

2.5A

Internal Circuit

*1 (Example) The output delay time (OFF to ON) is 1.5µs

where the output current is DC 24V, 50mA. Install an

external dummy resistor to increase the amount of current

when more responsiveness is required and the load is light.

• Since the output terminals are not electrically protected, an output line might be short-cir-

cuited or a connection fault might damage the LT unit. Please install an applicable fuse to

prevent an overload in the circuit, if necessary.

• LT3201-A1-D24-C Output Circuit (Source type)

0V A8

OUT5 A11

OUT4 B11 OUT3 A10 OUT2 B10 OUT1 A9 OUT0 B9

Dummy Resistor

DC 24V External Power

Fuse

2.5A

Internal Circuit

+24V B8

OUT5 A11

OUT4 B11 OUT3 A10 OUT2 B10 OUT1 A9 OUT0 B9

DC 24V

External Power

Internal Circuit

0V A8

Dummy Resistor

*1 (Example) The output delay time (ON to OFF) is 1.5µs where the output current is DC 24V, 50mA.

Install an external dummy resistor to increase the amount of current when more responsiveness is

required and the load is light.

• Since the output terminals are not electrically protected, an output line might be short-cir-

cuited or a connection fault might damage the LT unit. Please install an applicable fuse to

prevent an overload in the circuit, if necessary.

2-9

LT3000 Series Hardware Manual

 High-Speed Counter / Pulse Catch Input Specifications

DIO Standard Input/Output is used as a High-Speed Counter Input. The setup is done by the GP-Pro EX.

SEE

GP-Pro EX Reference Manual “Controlling External I/O”

Input

Input Points

DC24V Open Collector

Single Phase (4 points)

CT0 (IN0), CT1 (IN2), CT2 (IN4), CT3 (IN6)

Counter Pulse Catch

2 Phase (1 point or 2 points)

CT0 (IN0), CT1 (IN2) (used as pair) CT0: A Phase, CT1: B Phase CT2 (IN4), CT3 (IN6) (used as pair) CT2: A Phase, CT3: B Phase

DC24V Open Collector

IN0, IN2, IN4, IN6

Min. Pulse Width (Pulse Input)

Count Speed (Rise, Fall time)

t = 1 µs or less (100kpps)

Phase 1 Phase

High Speed Count Frequency

Count Edge Designation

Count Register 32 Bit UP/DOWN Counter ⎯

Counter Mode Change

Upper/Lower Limit Setting

Preload - Prestrobe Available ⎯

Marker Input (Counter Value Clear)

100Kpps 50Kpps ⎯

Available Not Available ⎯

Set through software ⎯

Not Available ⎯

None IN3, IN7 ⎯

10 µs

5 µs

90 degree phase differential 2-phase signal 1 phase + directional signal

Input signal ON width

5 µs or more

⎯

2-10

Chapter 2 Specifications

 Pulse/PWM Output Specifications

DIO Standard Input/Output is used as a Pulse Output or PWM Output. The setup is done by the GP-Pro EX.

SEE

GP-Pro EX Reference Manual “Controlling External I/O”

Pulse Output PWM Output

Output Points 4 Points

Output Method

PLS0 to PLS3 (OUT0 to OUT3) defined by user

PWM0 to PWM3 (OUT0 to OUT3) defined by user

Load Voltage DC24V

Min. Load Current 1mA

Max. Output Frequency Up to 65kHz possible per point (set through software)

Pulse Acceleration/ Deceleration Speed

ON Duty 50%±10% (at 65kHz)

Available ⎯

19 to 81% (at 65kHz)

*1 The ON Duty error (10%) will be reduced if the Output frequency is low.

*2 The ON Duty (effective range) will be widened if the Output frequency is low.

2-11

LT3000 Series Hardware Manual

2.1.4 Wiring to the DIO Connector

Be sure to remove the DIO Connector from the LT unit prior to starting wiring. Failure to do

so may cause an electric shock.

 Items Required to Wire Connectors

• Screwdriver

Recommended type: 1891348-1 <Tyco Electronics AMP.>

If another manufacturer is used, be sure the part has the following dimensions:

point depth: 1.5mm [0.06in.]

point width: 2.4mm [0.09in.]

Point shape should be DIN5264A, and meet Security Standard DN EN60900.

Also, the screwdriver’s tip should be flat as indicated in order to access the narrow hole of the connector:

Screwdriver Tip Shape

 DIO Cable Specifications

DIO Cable Diameter

Conductor Type Stranded Wire

AWG24 to 18 UL1015 or UL1007

7 mm [0.28in]

Conductor Length

*1 If the Conductor's end (individual) wires are not twisted correctly, the end

wires may either short against each other, or against an electrode.

The connectors are a spring clamp type.

 Connecting the DIO Cable

1. Insert a flathead screwdriver, at an angle, into the tool insertion hole (square-shaped hole) of the

connector.

2. When inserting the flathead screw driver, be sure that it is perpendicular to the center division wall.

2-12

• Make the insertion distance of the flathead screwdriver approximately 4 mm. Inserting forcefully may break the inside of the connector and will a cause of contact defect. Also, do not turn the flathead screwdriver while the tip is inside of the tool insertion hole (square-shaped hole).

Chapter 2 Specifications

3. The adjacent wire insertion hole (round-shaped hole) will be in an open state.

With the flathead screwdriver still inserted, insert the wire into the wire insertion hole (round-shaped

hole).

Screwdriver

Wire

Wire insertion hole (Round-shaped hole)

Tool insertion hole (Square-shaped hole)

4. Remove the flathead screwdriver from the tool insertion hole (square-shaped hole). The wire insertion

hole (round-shaped hole) will close and the wire will be secured. In the case of wire removal, remove

the desired wire by inserting a flathead screwdriver into the corresponding tool insertion hole (square-

shaped hole) following procedures (1) and (2).

5. Insert the wired DIO connector straight into the DIO I/F of the LT unit.

• Be sure to strip only the amount of cover required. If too much cover is removed,

the end wires may short against each other, or against an electrode, which can

create an electric shock. If not enough cover is removed the wire cannot carry a

charge.

• Do not solder the wire itself. This could lead to a bad or poor contact.

• Insert each wire completely into its opening. Failure to do so can lead to a unit

malfunction or short, either against wire filaments, or against an electrode.

• When wiring, be aware of the installation position, direction, and twisting of the

wiring as to not develop stress on the connector. Fix the cable near the LT by

cable clamp and set it loosely as to not place tension on the connector.

2-13

LT3000 Series Hardware Manual

2.1.5 Dimensions

The following dimensions apply to LT-3201A unit.

 Installation Fasteners Attached Dimensions

Unit: mm[in.]

129.2[5.09]

118[4.65]

Top

Left Side

21.5[0.85]

139.2[5.48]

130[5.12]

104[4.09]

Front Right Side

Bottom

76.5[3.01]

5[0.20]

21.5[0.85]

92[3.62]

2-14

 Cable Attached Dimensions

Unit: mm[in.]

Chapter 2 Specifications

86[3.39]

Rear Right sideLeft side

Bottom

• All the above values are designed in case of cable bending.

The dimensions given here are representative values depending on the type of

connection cable used. Therefore, they are all intended for reference only.

82[3.23]

98[3.86]

2-15

LT3000 Series Hardware Manual

 Panel Cut Dimensions

Unit: mm[in.]

118 .5

[4.67 ]

-0

+0.04

-0 4-R3[0.12] or less

-0

+0.04

[3.64 ]

-0

92.5

Panel thickness area

1.6[0.06] to 5.0[0.20]

 Installation Fasteners

Unit: mm[in.]

Φ10[0.39]

16[0.63]

11[0.43]

16.6[0.65]

31[1.22]

2-16

2.2 LT-3300 Series

2.2.1 General Specifications

 Electrical Specifications

Input Voltage DC24V

Rated Voltage DC19.2 to 28.8V

Allowable Voltage Drop 3ms (max.)

Power Consumption 27W (max.)

In-Rush Current 30A (max.)

Power Supply

Voltage Endurance

Insulation Resistance

 Environmental Specifications

Chapter 2 Specifications

AC1000V 20mA for 1 minute

(between charging and FG terminals)

DC500V 10MΩ (min.)

(between charging and FG terminals)

Surrounding Air Temperature

Storage Temperature -20 to +60°C

Ambient Humidity

Storage Humidity

Dust 0.1mg/m

Physical

Pollution Degree For use in Pollution Degree 2 environment

Atmosphere Free of corrosive gases

Air Pressure Vibration Resistance (availment altitude)

Vibration Resistance

Mechanical

Concussion Resistance

Noise Immunity

Electrical

Electrostatic Discharge Immunity

*1 Extended use in environments where surrounding air temperature is 40°C or higher

(Wet bulb temperature: 39°C max. - no condensation.)

(2000 meters above sea-level and below)

5 to 9Hz single-amplitude 3.5mm

9 to 150Hz constant-accelerated velocity 9.8m/s

X, Y, Z directions for 10 cycle (100 minute)

(147m/s2 X, Y, Z directions for 3 time)

6kV (complies with EN 61000-4-2 Level 3)

0 to +50°C

10 to 90% RH

and below (non-conductive levels)

800 to 1114hPa

IEC61131-2 compliant

Noise Voltage: 1000V

Pulse Duration: 1µs

Rise Time: 1ns

(via noise simulator)

P-P

may degrade the display quality and result in decreased contrast.

2-17

LT3000 Series Hardware Manual

 Structural Specifications

Grounding

Structu re

Cooling Method Natural air circulation

Installation

Weight Approx. 1.0kg [2.2lb] max. (unit only)

External Dimensions W167.5mm [6.59in] X H135.0mm [5.31in] X D78.0mm [3.07in]

Panel Cut Dimensions

*1 The front face of the LT unit, installed in a solid panel, has been tested using

conditions equivalent to the standards shown in the specification. Even though the

LT unit’s level of resistance is equivalent to these standards, oils that should have no

effect on the LT can possibly harm the unit. This can occur in areas where either va-

Grounding resistance of 100Ω 2mm2 or thicker wire,

or your country’s applicable standard.

(Same for FG and SG terminals)

Rating: Equivalent to IP65f NEMA #250 TYPE 4X/13

(Front surface at panel embedding)

Feature size: All-in-one

Installation configuration: Panel embedding

W156.0mm [6.14in] X H123.5mm [4.86in]

Panel thickness: 1.6 [0.06in] to 5.0mm [0.20in]

porized oils are present, or where low viscosity cutting oils are allowed to adhere to

the unit for long periods of time. If the LT’s front face protection sheet becomes

peeled off, these conditions can lead to the ingress of oil into the LT and separate

protection measures are suggested.

Also, if non-approved oils are present, it may cause deformation or corrosion of the

front panel’s plastic cover. Therefore, prior to installing the LT be sure to confirm the

type of conditions that will be present in the LT’s operating environment.

If the installation gasket is used for a long period of time, or if the unit and its gasket

are removed from the panel, the original level of the protection cannot be guaran-

teed. To maintain the original protection level, be sure to replace the installation gas-

ket regularly.

*2 As for dimensional tolerance everything +1/-0mm and R in angle are below R3.

2-18

2.2.2 Performance Specifications

 Performance Specifications

Model LT-3300L/LT-3300S/LT-3300T LT-3301L

Application

Data Backup

Interface

Clock Accuracy

Serial Interface

Ethernet Interface

DIO Interface

AUX Interface/ Expansion Unit

USB Host Interface

EX Module Interface

Ethernet (IEEE802.3u,10BASE-T/100BASE-TX) Connector: modular jack connector (RJ-

45)

Chapter 2 Specifications

FLASH EPROM 6MB

SRAM 128K byte

Used lithium battery for backup memory

COM1: RS232C/RS422/RS485

Asynchronous Transmission:

Data Length: 7 bit/8 bit

Parity: none, Odd or Even

Stop Bit: 1bit/2bit

Data transmission Speed: 2400bps to 115.2Kbps

Connector: DSUB-9pin plug

–

The interface to external I/O equipment

Input/Output points: 16-point inputs, 16-point outputs

Connector: 38 pins

Interface for external additional unit only

(such as communication equipment) (external)

Conforms to USB1.1. (TYPE-A conn.) x 1

Power Supply Voltage: DC5V ±5%

Output Current: 500mA (max.)

Communication Distance: 5m (max.)

Interface for Pro-face’s EX Modules

(Up to three EX modules can be connected)

± 65 seconds/ month (at room temperature)

Variable Area 64 KB SRAM (uses lithium battery)

Program Area 132 KB FLASH EPROM

Control Memory

*1 It is user active capacity. *2 The LT’s internal clock has a slight error. At normal operating temperatures and con-

ditions, with the LT operating from its lithium battery, the degree of error is 65 seconds per month. Variations in operating conditions and battery life can cause this error to vary from -380 to +90 seconds per month. For systems where this degree of error will be a problem, the user should be sure to monitor this error and make adjustments when required.

• When the message “RAAA051 Low battery” is displayed, supply power to the display unit and fully charge the battery. The battery charges within 24 hours to a level which allows backup operation. Completing a full charge requires about 96 hours (4 days).

• A Lithium battery’s lifetime is: 10 years when the battery’s ambient temperature is 40°C or less. 4.1 years when the battery’s ambient temperature is 50°C or less. 1.5 years when the battery’s ambient temperature is 60°C or less. When used for backup: Approximately 100 days, with a fully charged battery. Approximately 6 days, with a half-charged battery.

• When connecting the external device directly to the LT unit with an Ethernet cable, depending on the external device, communication may not be possible. Please connect over a network hub.

2-19

LT3000 Series Hardware Manual

 Display Specifications

Model

Display Type Monochrome LCD STN Color LCD TFT Color LCD

Resolution W320 x H240 pixels

Dot pitch W0.36mm [0.01in] x H0.36mm [0.01in]

Effective Display Area

Color/Shade level

Backlight

Brightness control 8 levels of adjustment available via touch panel

Contrast Adjustment 8 levels of adjustment available via touch panel -

Display Service Life

Backlight Service Life

Language Fonts

LT-3300L LT-3301L

W115.2mm [4.54in] x H86.4mm [3.40in]

Black and White (16

Shades)

(3-Speed Blink)

When replacement is required, contact your local LT distributor.)

MTBF value: 50,000hrs. (TYP)

(Backlight display service life is not included.)

50,000hrs. or more (at 25°C and continuous operation - period until

backlight brightness decreases to 50%)

Japanese: 6962 (JIS Standards 1 & 2)

(including 607 non-kanji characters)

ANK: 158 (Korean, Traditional Chinese

and Simplified Chinese fonts are downloadable.)

LT-3300S LT-3300T

4096 Colors

(3-Speed Blink)

White LED

(Not user replaceable.

(No 3-Speed Blink)/

(3-Speed Blink)

65,536 Colors

16,384 Colors

Character Sizes

Font Sizes

Text composition

8 x 8 dots 40 Char. x 30 rows

8 x 16 dots 40 Char. x 15 rows

Te xt

16 x 16 dots 20 Char. x15 rows

32 x 32 dots 10 Char. x 7 rows

*1 Font sizes other than those above can be set up by software.

Standard font: 8X8, 8X16, 16X16 and 32X32 dot fonts

Stroke font: 6 to 127dot fonts

Standard font: Width can be expanded up to 8 times.

Height can be expanded up to 8 times

 Touch Panel Specifications

Type Resistive Film (analog)

Resolution 1024 x 1024

Service Life 1,000,000 times or more

2-20

2.2.3 Interface Specifications

This section describes the specifications of each interface of the LT Series unit.

• The LT unit's serial Interface is not isolated. When the host (PLC) unit is also not

isolated, be sure to connect the #5 SG (Signal Ground) terminal to reduce the risk of

damaging the RS232C/RS422/RS485 circuit.

• In the LT unit, SG (signal ground) and FG (frame ground) are connected internally.

When connecting an external device to the LT using the SG terminal, be sure to

check that no short-circuit loop is created when you setup the system.

• When isolation is necessary, you can use the RS232C isolation unit (CA3-ISO232-01) on

COM1.

Chapter 2 Specifications

2-21

LT3000 Series Hardware Manual

Serial Interfaces (COM1)

This interface is used to connect an RS232C/RS422/RS485 *1 cable. D-sub 9-pin plug connector is used.

LT Connector XM2C-0942-502LX <OMRON Co.>

Interfit Bracket #4-40 (UNC)

Recommended Cable Connector XM2D-0901 <OMRON Co.>

Recommended Cable Cover XM2S-0913 <OMRON Co.>

Recommended Jack Screw (#4-40 UNC)

In the case of RS232C

Arrangement

(LT unit side)

Pin No.

1 CD Input Carrier Detect 2 RD(RXD) Input Receive Data 3 SD(TXD) Output Send Data 4 ER(DTR) Output Data Terminal Ready

5 SG - Signal Ground 6 DR(DSR) Input Data Set Ready 7 RS(RTS) Output Request to Send 8 CS(CTS) Input Send Possible

9 CI(RI)/VCC Input/-

Shell FG -

Signal Name Direction Meaning

XM2Z-0073 <OMRON Co.>

RS232C

Called status display

±5% Output 0.25A

+5V

(Common with SG)

Frame Ground

2-22

In the case of RS422C/RS485

Arrangement

(LT unit side)

*1 Communication method is switched via software.

*2 The RI/VCC selection for Pin #9 is switched via software. The VCC output is not protected against

overcurrent. To prevent damage or a unit malfunction, use only the rated current.

Pin No.

1 RDA Input Receive Data A(+) 2 RDB Input Receive Data B(-) 3 SDA Output Send Data A(+) 4 ERA Output Data Terminal Ready A(+) 5 SG - Signal Ground 6 CSB Input Send Possible B(-) 7 SDB Output Send Data B(-) 8 CSA Input Send Possible A(+) 9 ERB Output Data Terminal Ready B(-)

Shell FG -

Signal Name Direction Meaning

RS422/RS485

Frame Ground

(Common with SG)

 DIO Interface (Connector)

• When preparing the cable to connect the wiring, check the pin numbers inscribed

on the DIO Connector.

Chapter 2 Specifications

Applicable connector

Pin Arrangement Pin No. Signal Name Pin No. Signal Name

A19

(Cable connection side)

B19

2-1871940-9 <Tyco Electronics AMP.> CA7-DIOCN5-01<Pro-face>

A1 IN1 B1 IN0 (CT0)

A2 IN3 B2 IN2 (CT1)

A3 IN5 B3 IN4 (CT2)

A4 IN7 B4 IN6 (CT3)

A5 IN9 B5 IN8

A6 IN11 B6 IN10

A7 IN13 B7 IN12

A8 IN15 B8 IN14

A9 NC B9 COM

A10

A11

A12

A13

A14OUT5B14OUT4

A15OUT7B15OUT6

A16OUT9B16OUT8

A17 OUT11 B17 OUT10

A18 OUT13 B18 OUT12

A19 OUT15 B19 OUT14

Sink: NC

Source: +24V Source: +24V

Sink: 0V

Source: NC Source: 0V

OUT1

(PLS1, PWM1)

OUT3

(PLS3, PWM3)

B10

B11

B12

B13

Sink: +24V

(PLS0, PWM0)

(PLS2, PWM2)

Sink: 0V

OUT0

OUT2

• Parenthesized signal names ( ) indicate when Pulse output (PLS*), PWM output

(PWM*), or Counter Input (CT*) are used.

 Input Specifications

Rated Voltage DC24V

Maximum Allowable Voltage DC28.8V

Input Method Sink/Source Input

Rated Current

Input Resistance

Input Derating

6.5mA (DC24V) (IN0, IN2, IN4, IN6)

4.1mA (DC24V) (Other input)

Approx. 3.7kΩ (IN0, IN2, IN4, IN6) Approx. 5.9kΩ (Other input)

SEE



Input Derating (page2-24)

2-23

LT3000 Series Hardware Manual

Input Points 16

Common Lines 1

Common Design 16 points/1 common line

Operation Range

Input Delay

Time

ON Voltage DC19V or more

OFF Voltage DC5V or less

OFF to ON 0.5 to 20ms

ON to OFF 0.5 to 20ms

Input Signal Display No LED indicators

Status Display None

Isolation Method Photocoupler Isolation

External Connection 38-pin connector (used with Output section)

External Power Supply For Signal: DC 24V

*1 In the case of IN0, IN2, IN4, and IN6, the input delay time generates a 5µs-

delay. For example, in the case of a 0.5ms-cycle sampling:

5µs (ON to OFF) + 0.5ms (sampling cycle) + 5µs (OFF to ON) = 0.51ms

A minimum 0.51ms-restriction is imposed on the input pulse width.

In the case of IN1, IN3, IN5, and from IN7 to IN15, the input delay time gen-

erates a 0.5ms-delay. For example, in the case of a 0.5ms-cycle sampling:

0.5ms (ON to OFF) + 0.5ms (sampling cycle) + 0.5ms (OFF to ON) = 1.5ms

A minimum 1.5ms-restriction is imposed on the input-pulse width.

*2 Digital filter can be set at intervals of 0.5 ms.

 Input Derating

Using LT input voltage that exceeds the rated voltage, the input ON voltage, the number of input points or the

LT’s temperature can effect. Also, the LT’s input section could overheat, which could lead to an accident or

malfunction. Refer to the following drawing and perform Input Derating within the LT unit’s rated range.

(%)

100

For horizontal mounting DC24.0 to 26.4V

DC28.8V

For vertical mounting DC24.0 to 25.2V

Input ON Rate

01020304050 (°C)

Surrounding Operating Temperature

2-24

• Input Circuit

DC 24V

External Power

 Output Specifications

Output Terminal OUT0 to OUT3 OUT4 to OUT15

Rated Voltage DC24V

Allowable Voltage Range DC20.4V to DC28.8V

Output Method

Maximum Load Current 0.2A/point, 1.6A/common

Minimum Load Current 1mA

Output Voltage Drop DC 0.5V or less

Output Delay Time

Voltage Leakage (when OFF) 0.1mA or less

Clamp Voltage 39V ± 1V

Type of Output Transistor Output

Common Lines 2

Common Design 8 points/1 common line x 2

External Connection 38-pin connector (also used for Input)

Output Protection Type Output is unprotected

Internal Fuse 3.5A, 125V Chip fuse x 2 (not replaceable)

Surge Control Circuit Zener diode

Output Points 16

Output Signal Display No LED indicators

Status Display Element None

Isolation Method Photocoupler Isolation

External Power Supply For Signal: DC 24V

COM B9

IN15 A8 IN14 B8

IN13 A7 IN12 B7 IN11 A6 IN10 B6

IN9 A5 IN8 B5 IN7 A4 IN6 B4 IN5 A3 IN4 B3 IN3 A2 IN2 B2 IN1 A1 IN0 B1

*1 Dotted line shows connection to sink output type.

LT330*-*1-D24-K Sink Output

LT330*-*1-D24-C Source Output

OFF to ON

ON to OFF

5µs or less (With output at DC24V, 200mA)

Chapter 2 Specifications

Internal Circuit

1mA (Pulse/PWM output unavailable)

0.5ms or less (With output at DC24V, 200mA)

2-25

LT3000 Series Hardware Manual

• LT330*-*1-D24-K Output Circuit (Sink type)

+24V B10

Internal Circuit

*1 OUT0 to OUT3 only.

Fuse

3.5A

Fuse

0V B11

OUT7 A15

OUT6 B15 OUT5 A14 OUT4 B14 OUT3 A13 OUT2 B13 OUT1 A12

OUT0 B12

DC 24V External Power

OUT0 to OUT3 only

Dummy Resistor*

3.5A

0V A11

OUT15 A19

OUT14 B19 OUT13 A18 OUT12 B18 OUT11 A17 OUT10 B17 OUT9 A16

OUT8 B16

(Example) The output delay time (OFF to ON) is 1.5µs where the output current

is DC 24V, 50mA. Install an external dummy resistor to increase the amount of

current when more responsiveness is required and the load is light.

• Since the output terminals are not electrically protected, an output line might be short-cir-

cuited or a connection fault might burn the external devices and LT. Be sure to install an

applicable fuse for each output terminal if there should be the risk for the current running

over the rating.

2-26

• LT330*-*1-D24-C Output Circuit (Source type)

Internal Circuit

Fuse

3.5A

Fuse

3.5A

+24V B10

OUT7 A15

OUT6 B15 OUT5 A14 OUT4 B14 OUT3 A13 OUT2 B13 OUT1 A12

OUT0 B12

+24V A10

Chapter 2 Specifications

DC 24V External Power

OUT0 to OUT3 only

Dummy Resistor*

Internal Circuit

*1 OUT0 to OUT3 only.

(Example) The output delay time (ON to OFF) is 1.5µs where the output current is DC 24V, 50mA.

Install an external dummy resistor to increase the amount of current when more responsiveness is

required and the load is light.

OUT15 A19

OUT14 B19 OUT13 A18 OUT12 B18 OUT11 A17 OUT10 B17 OUT9 A16

OUT8 B16

0V B11

• Since the output terminals are not electrically protected, an output line might be short-cir-

cuited or a connection fault might burn the external devices and LT. Be sure to install an

applicable fuse for each output terminal if there should be the risk for the current running

over the rating.

2-27

LT3000 Series Hardware Manual

 High-Speed Counter / Pulse Catch Input Specifications

DIO Standard Input/Output is used as a High-Speed Counter Input. The setup is done by the GP-Pro EX.

SEE

GP-Pro EX Reference Manual “Controlling External I/O”

Input

Input Points

DC24V Open Collector

Single Phase (4 points)

CT0 (IN0), CT1 (IN2), CT2 (IN4), CT3 (IN6)

Counter Pulse Catch

2 Phase (1 point or 2 points)

CT0 (IN0), CT1 (IN2) (used as pair) CT0: A Phase, CT1: B Phase CT2 (IN4), CT3 (IN6) (used as pair) CT2: A Phase, CT3: B Phase

DC24V Open Collector

IN0, IN2, IN4, IN6

Min. Pulse Width (Pulse Input)

Count Speed (Rise, Fall time)

t = 1 µs or less (100kpps)

Phase 1 Phase

High Speed Count Frequency

Count Edge Designation

Count Register 32 Bit UP/DOWN Counter ⎯

Counter Mode Change

Upper/Lower Limit Setting

Preload - Prestrobe Available ⎯

Marker Input (Counter Value Clear)

100Kpps 50Kpps ⎯

Available Not Available ⎯

Set through software ⎯

Not Available ⎯

None IN3, IN7 ⎯

10 µs

5 µs

90 degree phase differential 2-phase signal 1 phase + directional signal

Input signal ON width

5 µs or more

⎯

2-28

Chapter 2 Specifications

 Pulse/PWM Output Specifications

DIO Standard Input/Output is used as a Pulse Output or PWM Output. The setup is done by the GP-Pro EX.

SEE

GP-Pro EX Reference Manual “Controlling External I/O”

Pulse Output PWM Output

Output Points 4 Points

Output Method

PLS0 to PLS3 (OUT0 to OUT3) defined by user

PWM0 to PWM3 (OUT0 to OUT3) defined by user

Load Voltage DC24V

Min. Load Current 1mA

Max. Output Frequency Up to 65kHz possible per point (set through software)

Pulse Acceleration/ Deceleration Speed

ON Duty 50%±10% (at 65kHz)

Available ⎯

19 to 81% (at 65kHz)

*1 The ON Duty error (10%) will be reduced if the Output frequency is low.

*2 The ON Duty (effective range) will be widened if the Output frequency is low.

2-29

LT3000 Series Hardware Manual

2.2.4 Wiring to the DIO Connector

Be sure to remove the DIO Connector from the LT unit prior to starting wiring. Failure to do

so may cause an electric shock.

 Items Required to Wire Connectors

• Screwdriver

Recommended type: 1891348-1 <Tyco Electronics AMP.>

If another manufacturer is used, be sure the part has the following dimensions:

point depth: 1.5mm [0.06in.]

point width: 2.4mm [0.09in.]

Point shape should be DIN5264A, and meet Security Standard DN EN60900.

Also, the screwdriver’s tip should be flat as indicated in order to access the narrow hole of the connector:

Screwdriver Tip Shape

 DIO Cable Specifications

DIO Cable Diameter

Conductor Type Stranded Wire

AWG24 to 18 UL1015 or UL1007

7 mm [0.28in]

Conductor Length

*1 If the Conductor's end (individual) wires are not twisted correctly, the end

wires may either short against each other, or against an electrode.

The connectors are a spring clamp type.

 Connecting the DIO Cable

1. Insert a flathead screwdriver, at an angle, into the tool insertion hole (square-shaped hole) of the

connector.

2. When inserting the flathead screw driver, be sure that it is perpendicular to the center division wall.

2-30

Chapter 2 Specifications

3. The adjacent wire insertion hole (round-shaped hole) will be in an open state.

With the flathead screwdriver still inserted, insert the wire into the wire insertion hole (round-shaped

hole).

Screwdriver

Wire

Wire insertion hole (Round-shaped hole)

Tool insertion hole (Square-shaped hole)

4. Remove the flathead screwdriver from the tool insertion hole (square-shaped hole). The wire insertion

hole (round-shaped hole) will close and the wire will be secured. In the case of wire removal, remove

the desired wire by inserting a flathead screwdriver into the corresponding tool insertion hole (square-

shaped hole) following procedures (1) and (2).

5. Insert the wired DIO connector straight into the DIO I/F of the LT unit.

• Be sure to strip only the amount of cover required. If too much cover is removed,

the end wires may short against each other, or against an electrode, which can

create an electric shock. If not enough cover is removed the wire cannot carry a

charge.

• Do not solder the wire itself. This could lead to a bad or poor contact.

• Insert each wire completely into its opening. Failure to do so can lead to a unit

malfunction or short, either against wire filaments, or against an electrode.

• When wiring, be aware of the installation position, direction, and twisting of the

wiring as to not develop stress on the connector. Fix the cable near the LT by

cable clamp and set it loosely as to not place tension on the connector.

2-31

LT3000 Series Hardware Manual

2.2.5 Dimensions

The following dimensions apply to LT-3300 series unit. The dimensions of the LT-3301* are the same. The following drawings show the LT-3300*.

Installation Fasteners Attached Dimensions

Unit: mm[in.]

130[5.12]

155.5[6.12]

Top

167.5[6.59]

77.6[3.06]

5[0.20]

Left Side

Front

100[3.94]

Bottom

135[5.31]

123[4.84]

Right Side

144.6[5.69]

134.6[5.30]

2-32

Cable Attached Dimensions

Unit: mm[in.]

31[1.22]

98[3.86]

64[2.52]

63[2.48]

Chapter 2 Specifications

[1.54]

Left Side

*1 The LT-3301L is not equipped with an Ethernet interface.

• All the above values are designed in case of cable bending.

The dimensions given here are representative values depending on the type of

connection cable used. Therefore, they are all intended for reference only.

Rear Right Side

Bottom

2-33

LT3000 Series Hardware Manual

 Panel Cut Dimensions

Unit: mm[in.]

156.0

[6.14 ]

-0

+0.04

-0 4-R3[0.12] or less

-0

+0.04

[4.86 ]

-0

123.5

Panel thickness area

1.6[0.06] to 5.0[0.20]

 Installation Fasteners

Unit: mm[in.]

Φ10[0.39]

16[0.63]

11[0.43]

16.6[0.65]

31[1.22]

2-34

3 Sample of the

Circuit Diagrams

1. Examples of Particular I/O Connections

3-1

LT3000 Series Hardware Manual

3.1 Examples of Particular I/O Connections

3.1.1 Connection to Pulse Motor Amplifier (CW/CCW type)

The following circuit diagrams show examples of connections between the LT and a pulse motor amplifier (in

the case where the transistor can be connected to the amplifier).

• The circuit of the pulse motor amplifier is illustrated by the DC24V CW and CCW con-

cept. However, the withstand voltage and the operating current of the coupler, which

receives pulse signals, vary by manufacturer. Please contact the amplifier manufacturer

before using.

 Output Sink Type

Amplifier (DC24V-capable)

Internal Circuit

+24V

Fuse

2.5A

OUT0

OUT3

DIO

DC 24V External Power supply

CW A

CW B

CCW A

CCW B

Lead wires from motor

3-2

• The output terminals for LT pulses are the ones that have the signal names OUT0, OUT1,

OUT2, and OUT3. For details of the setting, please refer to the GP-Pro EX

Reference Manual.

SEE

 Output Source Type

Chapter 3 Sample of the Circuit Diagrams

Amplifier (DC24V-capable)

Internal Circuit

Fuse

2.5A

+24V

OUT0

OUT3

DC 24V

DIO

External Power supply

Lead wires from motor

CW A

CW B

CCW A

CCW B

• The output terminals for LT pulses are the ones that have the signal names OUT0, OUT1,

OUT2, and OUT3. For details of the setting, please refer to the GP-Pro EX

Reference Manual.

SEE

3-3

LT3000 Series Hardware Manual

3.1.2 Connection to Pulse Motor Amplifier (Clock Up/Down System)

The following circuit diagrams show examples of connections between the LT and a pulse motor amplifier (in

the case where the transistor can be connected to the amplifier).

• The circuit of the pulse motor amplifier is illustrated by the DC24V clock up/down sys-

tem. However, the withstand voltage and the operating current of the coupler, which

receives pulse signals, vary by manufacturer. Please contact the amplifier manufacturer

before using.

 Output Sink Type

Amplifier (DC24V-capable)

Internal Circuit

DIO

DC 24V External Power supply

CW/CCW A

CW/CCW B

+24V

Fuse

2.5A

OUT0

Switching A

OUT3

Switching B

Lead wires from motor

• The output terminals for LT pulses are the ones that have the signal names OUT0, OUT1,

3-4

OUT2, and OUT3. For details of the setting, please refer to the GP-Pro EX

SEE

Reference Manual.

• Output signals for switching do not have to be connected to terminals that accommodate

high-speed output, and can be connected to general-purpose terminals (LT-3200 series:

OUT 4 and OUT5, LT-3300 series: OUT4 through OUT15).

 Output Source Type

Fuse

2.5A

+24V

Chapter 3 Sample of the Circuit Diagrams

Amplifier (DC24V-capable)

DC 24V

DIO

External Power supply

CW/CCW A

Internal Circuit

OUT0

OUT3

Lead wires from motor

• The output terminals for LT pulses are the ones that have the signal names OUT0, OUT1,

OUT2, and OUT3. For details of the setting, please refer to the GP-Pro EX

Reference Manual.

CW/CCW B

Switching A

Switching B

SEE

• Output signals for switching do not have to be connected to terminals that accommodate

high-speed output, and can be connected to general-purpose terminals (LT-3200 series:

OUT 4 and OUT5, LT-3300 series: OUT4 through OUT15).

3-5

LT3000 Series Hardware Manual

3.1.3 Connection to a Rotary Encoder

The following circuit diagrams show examples of connections between the LT and a rotary encoder (in the

case where the transistor can be connected to the rotary encoder).

 Output Sink Rotary Encoder

Internal Circuit

• The input terminals for the LT counter are the ones that have the signal names IN0, IN2,

IN4, and IN6. For details of the setting, please refer to the GP-Pro EX Refer-

ence Manual.

 Output Source Rotary Encoder

IN0

COM

DIO

DC 24V External Power supply

SEE

Rotary Encoder (DC24V-capable)

Main Circuit

Rotary Encoder (DC24V-capable)

Internal Circuit

3-6

IN0

DC 24V

COM

External Power supply

Main Circuit

• The input terminals for the LT counter are the ones that have the signal names IN0, IN2,

IN4, and IN6. For details of the setting, please refer to the GP-Pro EX Refer-

SEE

ence Manual.

4 Installation and

Wiring

1. Installation

2. Wiring Precautions

3. USB Cable Clamp Attachment/Removal

4-1

LT3000 Series Hardware Manual

4.1 Installation

This section describes the procedures and precautions for installing the LT Series units.

 Check the Installation Gasket’s Seating

It is strongly recommended that you use the installation gasket, since it absorbs vibration in addition to

repelling water.

For the procedure for attaching the installation gasket, refer to “5.3

SEE

5.3 Replacing the Installation Gasket (page 5-4)

• Before installing the LT into a cabinet or panel, check that the installation gasket

is securely attached to the unit.

• A gasket which has been used for a long period of time may have scratches or

dirt on it, and could have lost much of its dust and drip resistance. Be sure to

change the gasket periodically (or when scratches or dirt become visible).

Replacing the Installation Gasket”.

 Creating a Panel Cut

Create the correct sized opening required to install the LT, using the installation dimensions given.

Determine the panel thickness according to the panel thickness range with due consideration of panel strength.

SEE

LT-3200 Series

 Panel Cut Dimensions (page 2-16)

LT-3300 Series

 Panel Cut Dimensions (page 2-34)

• Check that the installation panel or cabinet’s surface is flat, in good condition and has no

jagged edges. Also, if desired, metal reinforcing strips can be attached to the inside of the

4-2

panel, near the Panel Cut, to increase the panel’s strength.

Chapter 4 Installation and Wiring

 Installation Requirements

• For easier maintenance, operation, and improved ventilation, be sure to install the LT at least 100 mm

[3.94 in.] away from adjacent structures and other equipment.

Unit: mm

100

• Be sure that the surrounding air temperature and the ambient humidity are within their designated ranges.

(Surrounding air temperature: 0 to 50°C, Ambient humidity: 10 to 90%RH, Wet bulb temperature: 39°C

max.) When installing the LT on the panel of a cabinet or enclosure, “Surrounding air temperature” indi-

cates both the panel face and cabinet or enclosure’s internal temperature.

100

Panel Face

• Be sure that heat from surrounding equipment does not cause the LT to exceed its standard operating tem-

perature.

Cabinet interior

4-3

LT3000 Series Hardware Manual

• When installing the LT in a slanted panel, the panel face should not incline more than 30°.

• When installing the LT in a slanted panel, and the panel face inclines more than 30°, the surrounding

operating temperature must not exceed 40°C. You may need to use forced air cooling (fan, A/C) to ensure

the surrounding operating temperature is 40°C or below.

• The LT-3200 series does not support portrait mounting. When the LT-3300 series is used with the EX

module attached to the rear side, it cannot be mounted in portrait orientation.

30° or less

4-4

 Installing the LT

(1) Insert the LT into the panel cut, as shown.

(2) Insert the installation fasteners into the LT

insertion slots, at the left and right side or top

Chapter 4 Installation and Wiring

and bottom side of the unit. (total: 4 slots)

• Insert each installation fastener

securely into the slot's recess

(shaded area). If the fasteners

are not correctly attached, the

LT unit may shift or fall out of the

panel.

left and right

(Example) LT-3200 Series

top and bottom

Slots

Left Side Right Side

<LT-3200 Series>

Top Side

Slots

Bottom Side

<LT-3300 Series>

Installation Panel

Hook

4-5

LT3000 Series Hardware Manual

(3) Insert each of the fasteners shown below. Be

sure to pull the fastener back until it is flush

with the rear of the attachment hole.

(4) Use a Phillips screwdriver to tighten each

fastener screw and secure the LT in place.

• Tightening the screws with too much force can damage the LT unit’s plastic case.

• The torque required to tighten these screws is 0.5 N•m.

4-6

4.2 Wiring Precautions

This section describes the procedures and precautions for wiring power cords.

4.2.1 Connecting the Power Cord

To avoid an electric shock, prior to connecting the LT unit’s power cord terminals to the

power terminal block, confirm that the LT unit’s power supply is completely turned OFF, via

a breaker, or similar unit.

Supplying a power voltage other than that specified will damage the power source and the

LT unit .

Since there is no power switch on the LT unit, be sure to attach a breaker-type switch to its

power cord.

When the FG terminal is connected, be sure the wire is grounded.

Chapter 4 Installation and Wiring

• When the FG terminal is connected, be sure the wire is grounded. Not grounding

the LT unit will result in excess noise and vibration.

• The SG and FG terminals are connected internally in the LT unit.

When connecting the SG wire to another device, be sure that the design of the

system/connection does not produce a shorting loop.

4-7

LT3000 Series Hardware Manual

 When the DC Type

Power Cord Specifications

Power Cord Diameter 0.75 to 2.5mm

Conductor Type Simple or Twisted Wire

(18-12AWG)

Conductor Length

• Use copper conductors only.

• If the Conductor’s end (individual) wires are not twisted correctly, the end wires

may either short against each other, or against an electrode.

Power Connector (Plug) Specifications

Insertion

Direction

• The power supply connector (plug) is CA5-DCCNM-01 (made by Pro-face) or

MSTB2,5/3-ST-5,08 (made by Phoenix Contact

*1 For details, please contact your local Phoenix Contact distributor.

7mm[0.28in.]

24V

FG Grounding Terminal connected to the LT

4-8

Wiring

When connecting the Power Cord, use the following items when performing wiring. (Items are made by

Phoenix Contact.)

Recommended Driver SZF 1-0.6x3.5 (1204517)

AI 0.75-8GY (3200519) Recommended Pin Te rm i na l s

Recommended Pin Terminal Crimp Tool

AI 1-8RD (3200030)

AI 1.5-8BK (3200043)

AI 2.5-8BU (3200522)

CRIMPFOX ZA3 (1201882)

Chapter 4 Installation and Wiring

Connecting the Power Cord

• Be sure to remove the connector from the LT unit prior to starting wiring. Failure

to do so may cause an electric shock.

• The temperature rating of field installed conductors: 75°C only.

(1) Confirm that the power cord is unplugged from the power supply.

(2) Strip the membrane of the power cord, twist the wire ends, and connect them to the Power Connector

(Plug).

• Use a flat-blade screwdriver (Size 0.6 X 3.5) to tighten the terminal screws.

The torque required to tighten these screws is 0.5 to 0.6N•m [5-7lb•in].

• Do not solder the cable connection.

(3) Reattach the Power Connector (Plug).

−

Power Connector (Plug)

• Be sure to twist the power cords together, up to the power connector.

Power Connector (Socket)

Bottom

<LT-3201A>

4-9

LT3000 Series Hardware Manual

4.2.2 Connecting the Power Supply

This section describes the precautions for supplying a power voltage.

Constant

Voltage

Transformer

nsulating

Transformer

Main Power

Main

Power

Twiste d-pair c ord

Twisted-pair cord

LT Pow e r

Input/Output

Power

Input/ Output Power

Main Circuit

Input/Output

Unit

Input/Output

Unit

Input/Output

Unit

Operation

Unit

• If the supplied voltage exceeds the LT unit’s range,

connect a constant voltage transformer.

SEE

Chapter 2 Specifications (page 2-1)

• For between the line and ground, select a power supply

that is low in noise. If there is an excess amount of noise,

connect a insulating transformer.

• Use constant voltage and

insulating transformers with

capacities exceeding Power

Consumption value.

• When supplying power to the LT unit, be sure to

separate the input/output and power lines, as shown.

• To increase the noise resistance quality of the power

cord, simply twist each power wire before attaching the

Ring Terminal.

• The power supply cable must not be bundled or

positioned close to main circuit lines (high voltage, high

current), or input/output signal lines.

• Connect a lightening surge absorber, as shown in the

diagram, to deal with power surges.

• To avoid excess noise, make the power cord as short as

possible.

• 24V DC input unit is must be used with a Class 2 power

4-10

Lightening Surge

Absorber

supply.

• Be sure to ground the surge

absorber (E1) separately from the

LT unit (E2).

• Select a surge absorber that has

a maximum circuit voltage greater

than that of the peak voltage of

the power supply.

4.2.3 Grounding

This section describes the precautions for grounding the LT unit.

Do not use common grounding, since it can lead to an accident or machine breakdown.

Chapter 4 Installation and Wiring

(a) Exclusive Grounding (BEST)

(b) Exclusive Grounding (OK)

Other

Equipment

Other

Equipment

• When supplying power to the LT unit, be sure to separate the

input/output and power lines, as shown. [diagram (a)]

• Check that the grounding resistance is

100Ω or less.

• FG and SG terminals are internally

connected in the LT. When connecting

an external device to the LT using the

SG terminal, be sure to check that no

short-circuit loop is created when you

setup the system.

• The grounding wire should have a cross

sectional area greater than 2mm

Create the grounding point as close to

the LT unit as possible, and make the

wire as short, as possible. When using

a long grounding wire, replace the thin

wire with a thicker wire, and place it in a

duct.

Other

Equipment

• If exclusive grounding is not possible, use a common

grounding point. [diagram (b)] A grounding or equivalent

should be used for the grounding point.

• If the equipment does not function properly

when grounded, disconnect the ground wire

from the FG terminal.

4-11

LT3000 Series Hardware Manual

4.2.4 Wiring Precautions

To help prevent noise and interference problems, separate all control, communication and power lines by

placing them in a separate ducts.

Duct for I/O Signal

Lines

If different wires must be placed in the same duct, separate them with an earthed/grounded divider.

I/O Signal Lines Control Lines Power Lines

Duct for Control

Lines

Grounded

Separators

Duct for Power

Lines

Duct (non-conducting resin/plastic)

Earth/Ground

4-12

• If the lines cannot be separated, use shielded lines and create a ground from the shield

line.

• Use noise-reducing external wiring methods to increase overall system reliability.

• To prevent power surges or noise interference, use ducts to separate all DC I/O

or current circuit wires from communication cables.

• To prevent malfunctions due to noise, communication cables must be wired

separately from high-frequency lines and power lines such as high-voltage lines,

high-current lines, and inverters.

4.2.5 Installation Precautions

External power failure or failure of the LT unit may cause abnormal behavior.

To prevent such abnormal behavior from leading to the abnormal operation of the entire system, and to ensure

fail-safe operation, configure circuits which may lead to machine damage or accident due to abnormal

operation (emergency stop circuit, protection circuit, interlock circuit, etc.) externally to the LT.

This section describes examples of the system circuit design to improve system reliability and to ensure

optimum performance.

 Fail-safe Design of the Electric Circuit

Design the electric circuit with consideration to equipment malfunctions caused when the LT is turned on by

a delay among the startup times of the control equipment connected to the LT output unit (especially the one

operated by a DC power supply), the LT unit itself, and the program. When remote I/O is used, create a

program that checks the status of the terminal with a logic program.

For example, connect voltage relay coils to the power supply circuit of the LT output unit and the power

Chapter 4 Installation and Wiring

supply circuit of the connected control equipment, and connect the contact to the LT input unit. Configure the

circuit to check the ON signal from the voltage relay in the logic program before executing the ladder of the

control equipment connected to the LT output unit.

 Rated Voltage

Be sure to supply an appropriate power supply voltage to your LT that is within the specified range.

 Power-down

LT unit enters power-down status when an instantaneous power interruption of the rated voltage continues for

10ms or longer.

When the LT unit enters power-down status, it stops the calculation even if the instruction is not finished.

For example, when the LT unit enters power-down status while 100 words of data are being transferred by an

FMOV instruction, the transfer stops midway.

Consequently, design your program with consideration to power-down occurrences.

4-13

LT3000 Series Hardware Manual

 Emergency Stop Circuit

Do not process emergency stop signals with a software program by inputting the signal to the LT.

Configure the emergency stop circuit externally to the LT as shown in the figure below:

24VDC

Emergency stop button b (normally closed) contact

Output

Machine to be controlled

Input

 Interlock Circuit 1

To use the LT or a PLC to control a motor circuit for forward/reverse rotation, configure the interlock circuit

shown below externally to the LT.

Auxiliary b (normally closed) contact of electromagnetic switch

for motor reverse rotation

Motor forward rotation signal

Electromagnetic switch for motor forward rotation

4-14

Motor reverse rotation signal

Auxiliary b contact of electromagnetic switch for motor forward rotation

Electromagnetic switch for motor reverse rotation

Chapter 4 Installation and Wiring

• After executing an internal program, the LT outputs ON/OFF information to the output

devices at the same time. For example, the electromagnetic switches for forward and

reverse rotation of a motor are turned on and off at the same time.

Consequently, a situation may arise in which both of the main contacts of the motor cir-

cuits for the electromagnetic switches for forward and reverse rotation may turn on, caus-

ing a short-circuit of the R and T phases. To avoid this situation, you need to provide the

interlock circuit shown above or use an electromagnetic switch equipped with a mechani-

cal interlock for a forward/reverse circuit.

 Interlock Circuit 2

If there is a possibility that the abnormal operation of the LT may lead to an accident, design a fail-safe

measure to configure an interlock circuit with external hardware devices.

For a system which requires the running motor to stop before all other processes when the travel limit switch

is activated, never design a system in which the signals from the travel limit switch are input to the input

terminals of the LT and then processed using software.

Configure a circuit that reliably stops the running motor using hardware as shown below.

Travel limit switch

Running motor control signal

Running motor control circuit

Emergency stop switch

Direct input to the emergency stop circuit of the control unit

Travel limit switch

4-15

LT3000 Series Hardware Manual

4.3 USB Cable Clamp Attachment/Removal

This clamp is used to prevent the USB cable connected to the USB Host Interface on the bottom of the LT unit

from being unplugged due to vibration or other causes.

• When the USB Host Interface is used in the hazardous locations specified in

ANSI/ISA-12.12.01, use the USB holder to secure the USB cable. The USB Host

Interface cannot be used unless the connectors attached to the LT unit and

connected device are completely secured to prevent disconnection.

4.3.1 LT-3200 Series

 Attachment

(1) Before starting the procedure, orient the two tabs on both sides of the USB Holder in the direction of the

arrows in the figure and remove the USB Cover.

Tabs

(2) With the main unit display part positioned so that it is facing down, attach the USB holder to the USB

host interface. Do this by inserting the picks on the USB holder itself into the attachment holes on the

main unit. Insert the upper hook first.

Attachment Hole

USB I/F

4-16

Chapter 4 Installation and Wiring

(3) Insert the USB cable into the USB Host Interface.

USB cable

(4) Attach the USB cover to the USB host interface. Insert the USB cover into the tab of the USB holder.

USB Holder

USB cover

• Insert the USB cover in the orientation shown in the illustration above.

4.3.2 LT-3300 Series

 Attachment

(1) Before starting the procedure, pull out the USB cover from the USB holder by holding the top and

bottom of the USB holder and pressing down the tab on the USB cover.

cPress down the tab,

dAnd pull out the

USB cover.

4-17

LT3000 Series Hardware Manual

(2) With the main unit display part positioned so that it is facing down, attach the USB holder to the USB

host interface. Insert the picks on the top of the USB holder into the attachment holes on the main unit, and then insert the holder into the USB host interface so that the holder is secured in the main unit.

Attachment Hole

(3) Insert the USB cable into the USB Host Interface.

USB cable

(4) Attach the USB cover to the USB host interface. Hold the USB cover in the orientation shown in the

figure and insert it into the USB holder.

USB Holder

USB cover

4-18

Chapter 4 Installation and Wiring

 Removal

(1) Pull out the USB cover from the USB holder by pressing down the tab on the USB cover.

cPress down the tab,

dAnd pull out the USB cover.

(2) Insert the tip of a flat-blade screwdriver into the hole on the bottom of the USB holder and raise the

handle so that the USB holder detaches from the USB host interface.

Screwdriver

4-19

LT3000 Series Hardware Manual

4-20

5 Maintenance

1. Cleaning the Display

2. Periodic Check Points

3. Replacing the Installation Gasket

4. Replacing the Backlight

This chapter explains cautions and inspection criteria that will ensure trouble-free use of the LT.

5-1

LT3000 Series Hardware Manual

5.1 Cleaning the Display

When the surface or frame of the display become dirty, soak a soft cloth in water with a neutral detergent,

wring the cloth tightly, and wipe the display.

• Do not use paint thinner, organic solvents, or a strong acid compound to clean the

unit.

• Do not use hard or pointed objects to operate the touch-screen panel, since it can

damage the panel surface.

5-2

5.2 Periodic Check Points

To keep your LT unit in its best condition, please inspect the following points periodically.

 LT Operation Environment

 Is the operating temperature within the allowable range (0ºC to 50ºC)?

 Is the operating humidity within the specified range (10%RH to 90%RH, dry bulb temperature of 39ºC or

less)?

 Is the operating atmosphere free of corrosive gasses?

When using the LT unit inside a panel, the ambient environment refers to the interior of the panel.

 Electrical Specifications

 Is the input voltage appropriate?

DC19.2 to 28.8V

 Related Items

Chapter 5 Maintenance

 Are all power cords and cables connected properly? Have any become loose?

 Are all mounting brackets holding the unit securely?

 Are there many scratches or traces of dirt on the installation gasket?

5-3

LT3000 Series Hardware Manual

5.3 Replacing the Installation Gasket

The installation gasket provides protection against dust and moisture.

• A gasket which has been used for a long period of time may have scratches or

dirt on it, and could have lost much of its water resistance. Be sure to change the

gasket at least once a year, or when scratches or dirt become visible.

• The LT unit installation gasket’s model number is as follows.

LT-3200 Series ST400-WP01

LT-3300 Series CA3-WPG6-01

 Installation Gasket Attachment Procedure

(1) Place the LT on a flat, level surface facing the display face downwards.

(2) Remove the gasket from the LT.

(3) Attach the new gasket to the LT. Be sure to insert the gasket into the LT’s groove so that the gasket’s

groove sides are vertical.

LT R e a r F a c e

Gasket Seam

(LT-3300*)

(4) Check that the gasket is attached correctly to the LT.

Gasket

Installation Groove

5-4

Chapter 5 Maintenance

• The gasket must be inserted correctly into the groove for the LT’s moisture

resistance to be equivalent to IP65f.

• Since the gasket is flexible but not elastic, be careful not to stretch it

unnecessarily, as doing so could tear the gasket.

• Be sure the gasket’s seam is not inserted into any of the unit’s corners, only in the

straight sections of the groove. Inserting it into a corner may lead to its eventually

tearing.

• To ensure stable resistance against dust and moisture, insert the gasket so that

the seam is at the bottom of the LT unit.

• The upper surface of the gasket should protrude approximately 2.0 mm out from

the groove. Be sure to check that the gasket is correctly inserted before installing

the LT into a panel.

Unit: mm

2.0mm

5-5

LT3000 Series Hardware Manual

5.4 Replacing the Backlight

• The LT’s backlight cannot be replaced by the user. When the backlight needs to

be replaced, please contact your local LT distributor.

5-6

Proface LT3300 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Preface

Essential Safety Precautions

Information Symbols

About the Manuals

LT3000 Series Model Name Indication

LT3000 Series Model Names

Global Code

Package Contents

Installation prerequisites for standards

CE Marking

KC Markings

About Revision

Contents

1 Overview

1.1 System Design

1.1.1 LT-3200 Series

1.1.2 LT-3300 Series

1.2 Accessories

1.2.1 USB Host Interface

1.2.2 Serial Interface Item

1.2.3 Option Items

1.2.4 Maintenance Items

1.2.5 EX Module

1.3 Part Names and Functions

1.3.1 LT-3200 Series

1.3.2 LT-3300 Series

2 Specifications

2.1 LT-3200 Series

2.1.1 General Specifications

2.1.2 Performance Specifications

2.1.3 Interface Specifications

2.1.4 Wiring to the DIO Connector

2.1.5 Dimensions

2.2 LT-3300 Series

2.2.1 General Specifications

2.2.2 Performance Specifications

2.2.3 Interface Specifications

2.2.4 Wiring to the DIO Connector

2.2.5 Dimensions

3.1 Examples of Particular I/O Connections

3.1.1 Connection to Pulse Motor Amplifier (CW/CCW type)

3.1.2 Connection to Pulse Motor Amplifier (Clock Up/Down System)

3.1.3 Connection to a Rotary Encoder

4.1 Installation

4.2 Wiring Precautions

4.2.1 Connecting the Power Cord

4.2.2 Connecting the Power Supply

4.2.3 Grounding

4.2.4 Wiring Precautions

4.2.5 Installation Precautions

4.3 USB Cable Clamp Attachment/Removal

4.3.1 LT-3200 Series

4.3.2 LT-3300 Series

5 Maintenance

5.1 Cleaning the Display

5.2 Periodic Check Points

5.3 Replacing the Installation Gasket

5.4 Replacing the Backlight