Precor S3.25 User Manual 2

S3.25

Leg Press Option

Assembly Instructions

S3.25 Leg Press Option Assembly Instructions

Important Safety Instructions

Before beginning any fitness program, you should
obtain a complete physical examination from your
physician.

Il est conseillé de subir un examen médical complet
avant d’entreprendre tout programme d’exercise. Si
vous avez des étourdissements ou des faiblesses,
arrêtez les exercices immédiatement.

When using exercise equipment, basic precautions
should always be taken, including the following:

• Read all instructions before using the Leg Press
Option. These instructions are written to ensure
your safety and to protect the unit.

• Do not allow children on or near the equipment.

• Use the equipment only for its intended
purpose as described in this guide. Do not
use accessory attachments that are not
recommended by the manufacturer: such
attachments might cause injuries.

• Wear proper exercise clothing and shoes for
your workout—no loose clothing.

• Use care when getting on or off the unit.

• Do not overexert yourself or work to
exhaustion.

• If you feel any pain or abnormal symptoms,
stop your workout immediately and consult
your physician.

• Never operate the unit when it has been
dropped or damaged. Return the equipment to a
service center for examination and repair.

• Never drop or insert objects into any opening
in the equipment. Keep hands away from moving
parts.

• Always check the unit and its cables before
each use. Make sure that all fasteners and
cables are secure and in good working
condition.

• Do not use the equipment outdoors.

Personal Safety During Assembly

• It is strongly recommended that a qualified dealer
assemble the equipment.

• Read each step in the assembly instructions and
follow the steps in sequence. Do not skip ahead. If
you skip ahead, you may learn later that you have
to disassemble components and that you may
have damaged the equipment.

• Assemble and operate the Leg Press Option on a
solid, level surface. Locate the unit a few feet from
walls or furniture to provide easy access.

The Leg Press Option is designed for your enjoyment. By
following these precautions and using common sense,
you will have many safe and pleasurable hours of
healthful exercise with your Precor equipment.

Assistance is required.

Obtaining Service

Do not attempt to service the Leg Press
Option yourself. This unit does not contain
any user-serviceable parts.

For information about product operation or
service, check out the Precor web site at
www.precor.com or contact an authorized
Precor dealer or a Precor factory-authorized
service company. To locate the dealer or service
person nearest you, call 1-800-347-4404.

If you call or e-mail Customer Support, have
your serial and part numbers available.

You can find the serial number printed on a
label on the Upright Seat Support of the Leg
Press Option. For future reference, write the
serial number in the space below.

Serial number: _____________

Important Safety Instructions

IMPORTANT SAFETY INSTRUCTIONS

page 2

S3.25 Leg Press Option Assembly Instructions

Table of Contents

Important Safety Instructions ............................................................... 2

Personal Safety During Assembly ................................................................................. 2

Obtaining Service .......................................................................................................... 2

Before You Begin ................................................................................... 4

1
2

3

Unpacking the Equipment ............................................................................................. 4

Preparations........................................................................................... 5

Required Tools............................................................................................................... 5

Installation Requirements .............................................................................................. 5

Assembly Tips ............................................................................................................... 5

Assembly Instructions .......................................................................... 6

1. Remove the Shroud ................................................................................................... 7

2. Attach the Cross Brace to the S3.25 ......................................................................... 8

3. Assemble the Frame .................................................................................................. 9

4. Assemble the Seat Pads............................................................................................ 11

5. Route the Cable ......................................................................................................... 12

6. Assemble the Cable and Pulleys ............................................................................... 13

7. Replace the Shroud ................................................................................................... 15

Table of Contents

4

Adjustments ........................................................................................... 16

1. Stretch the Cable ....................................................................................................... 16

2. Rotate the Cam Washer ............................................................................................ 17

3. Adjust the Rubber Bumper on the Leg Press Option................................................. 18

Warranty Registration ........................................................................... 19

Warranty Card and Specifications ...................................... Back cover

page 3

S3.25 Leg Press Option Assembly Instructions

1

Thank you for purchasing the Leg Press Option for
your Precor equipment. This option will add a new
dimension to your strength-training regimen. For
proper installation, please read this guide thoroughly
and follow the assembly instructions.

Unpacking the Equipment

The Leg Press Option is carefully tested and inspected
before shipment. Precor ships the unit in several
pieces that require assembly. Two people are required
to assemble this equipment. Ask for assistance during
the assembly process.

• Review the
next page.

• Carefully unpack the pieces and lay them on
the floor near the place where you plan to use
the equipment.

If any items are missing, contact the dealer from whom
you purchased the unit or call 1-800-347-4404 to find
the dealer nearest you.

Before You Begin

Installation Requirements

on the

Before You Begin

page 4

S3.25 Leg Press Option Assembly Instructions

2

CAUTION: To set up this equipment, you will need
assistance. Do not attempt assembly by yourself.

You must review and follow the instructions in this
guide. If you do not assemble and use the Leg Press
Option according to the following guidelines, you could
void the Precor limited warranty.

Required Tools

You need to obtain these tools before assembling
the unit:

❑ ¾-inch socket wrench

❑ ¾-inch box-end wrench

❑ ⁹⁄₁₆-inch socket wrench

❑ ⁹⁄₁₆-inch box-end wrench

❑ Two adjustable pliers or crescent wrenches

❑ Standard set of metric Allen wrenches

❑ Utility knife or scissors

❑ Measuring tape

Preparations

Installation Requirements

Follow these installation requirements when
assembling the unit:

• Fill out and mail the limited warranty card.
The warranty card is found on the back cover of
this guide.

• Set up the Leg Press Option on a solid, flat
surface. A smooth, flat surface under the unit helps
keep it level. A level unit has fewer malfunctions.

• Provide ample space around the machine.
Open space around the machine allows for easier
access.

• Insert all bolts in the same direction. For
aesthetic purposes, insert all the bolts in the same
direction unless specified (in text or illustrations) to
do otherwise.

• Leave room for adjustments. Tighten fasteners
such as bolts, nuts, and screws, so that the unit is
stable, but leave room for adjustments. Do not fully
tighten fasteners until instructed in the assembly
steps to do so.

Assembly Tips

• A 6-inch scale is provided at the bottom of every
assembly instruction page. Use this scale to identify
the correct size bolts and spacers. The head of a
bolt is not used in measuring the length of a bolt.

To find out the length of a particular bolt, measure its
shank (the long, narrow part beneath the head).
Refer to the following diagram.

• Read all caution notes on each page before
completing that step.

Bolt head

Bolt threads

Shank

• Some pieces have extra holes that you will not use.
Use only those holes indicated in the instructions
and illustrations.

• While you may be able to assemble the Leg Press
Option by using the illustrations only, refer to the
text for important safety cautions and notes.

To determine the
length of a bolt,
measure its shank.

Preparations

page 5

S3.25 Leg Press Option Assembly Instructions

Assembly

3

Assembly of the Leg Press Option takes professional
installers about 1 hour to complete. If this is the first time
you have assembled this type of equipment, plan on
significantly more time.

Professional installers are highly recommended!

CAUTION: Obtain assistance! Do not attempt
to assemble the Leg Press Option by yourself.
Because of the weight and size of the Leg Press
Option, you could be injured or damage the
equipment. Review the
on page 5 before proceeding.

The Leg Press Option comes in one box. It can be
installed on either the S3.25 or S3.45 Precor Strength
Training Equipment. Note that the location where you
attach the Cross Brace to the Seat Frame differs.
As you read through the assembly instructions, be
sure that you are using the correct mounting holes for
your unit.

Instructions

Installation Requirements

Be careful to assemble the components in the
sequence presented in this guide.

Note: As with any assembled part, proper alignment and
adjustment is critical. While tightening the fasteners, be
sure to leave room for adjustments. Do not fully tighten
the fasteners until instructed to do so.

Assembly Instructions

1 2 3 4 5 6

page 6

S3.25 Leg Press Option Assembly Instructions

1. Remove the Shroud

Important: For ease of assembly, the fasteners and
hardware for each step are labeled and packaged in
separate bags.

Note: If you are assembling the Leg Press Option
along with your S3.25, go directly to Step 2.

Before you can attach the Leg Press Option to the unit,
you must remove the Shroud.

A. Remove the Shroud by loosening and removing

six 2¾-inch bolts
six washers
six locknuts

Top Beam

Notch in Shroud fits
around Top Beam
fastener

B. Pull the Shroud away from the S3.25 and lay it and

its fasteners on the floor in a secure place.

Note: The top of the Shroud has a notch in it to
help you clear the Top Beam fastener.

6 - 2¾" bolts
6 - washers

A

6 - locknuts

Remove Shroud

B

1 2 3 4 5 6

Step 1. Remove the Shroud

page 7

S3.25 Leg Press Option Assembly Instructions

2. Attach the Cross Brace to the
S3.25

Note: If you are assembling the Leg Press Option
along with the S3.25, you should complete Step 10 in
the

S3.25 Assembly and Maintenance Guide

attaching the Cross Brace.

A. Align the Cross Brace to the S3.25 Rear Upright

and secure it using
two 3-inch bolts
four washers
two locknuts
Wrench tighten.

before

Step 2. Attach the Cross Brace to the S3.25

2 - 3" bolts
4 - washers

A

2 - locknuts

1 2 3 4 5 6

Cross Brace

page 8

S3.25 Leg Press Option Assembly Instructions

3. Assemble the Frame

A. With someone helping you, lift the Seat Frame

upright. Have your assistant hold it in place while
you attach the Cross Brace in the next step.

B. Attach the Cross Brace to the holes found at the

front of the Seat Frame using
two 3-inch bolts
four washers
two locknuts
Wrench tighten.

Backpad
Support

Backpad
Support

Pop Pin

C

Important: A label on the Seat Frame indicates the
mounting holes you must use to attach the Cross
Brace to the S3.25 Leg Press Option.

C. Slide the Backpad Support into the Seat Frame,

locking it in place with the Pop Pin.

Cross Brace

Label indicates mounting
location for the S3.25

B

2 - 3" bolts
4 - washers
2 - locknuts

Have an assistant hold
the Seat Frame stable

A

and upright while you
attach the Cross Brace

Seat Frame

Step 3. Assemble the Frame

1 2 3 4 5 6

page 9

S3.25 Leg Press Option Assembly Instructions

D. Assemble the Footrest by resting the Pivot Arm

on the Rubber Bumper. Make sure that the red
arrow on the back of the Footrest points toward
the ceiling.

E. Attach the Footrest to the Pivot Arm and Pivot

Tube using
two large ½-inch by 3-¼-inch bolts
four ½-inch-diameter washers
two large ½-inch locknuts
Wrench tighten enough to allow free movement of
the Pivot Arm.

F. Attach the Handle to the Seat Frame using

two 3-inch bolts
four washers
two locknuts
Wrench tighten.

Footrest

Pivot Arm

Handle

2 - large ½" x 3¼" bolts
4 - ½" diameter washers

E

2 - large ½" lock nuts

2 - 3" bolts
4 - washers

F

2 - locknuts

Pop Pin

Step 3. Assemble the Frame, Continued

Footrest

Red Arrow Label

Pivot Arm

Pivot Tube

Rest the Pivot Arm on the

D

Rubber Bumper

Rubber Bumper

1 2 3 4 5 6

Seat Frame

page 10

S3.25 Leg Press Option Assembly Instructions

4. Assemble the Seat Pads

A. Attach one of the Seat Pads to the Seat Bracket

Support using
two 1¼-inch bolts
two washers
Wrench tighten.

B. Lift the Pop Pin and slide the Seat Pad out of the

way to assemble the other Seat Pad.

C. Attach the remaining Seat Pad to the Seat Frame

using
two 3-inch bolts
two washers
Wrench tighten.

Note: Make sure that the seams on the Seat Pads
face down toward the frame.

Note: If you are assembling the Leg Press Option and
the S3.25 simultaneously, return to Step 11 in the

S3.25 Assembly and Maintenance Guide

now.

Seat Pad
used as a
back rest

Seat Bracket Support

Handle

Seat Frame

2 - 1¼" bolts
2 - washers

A

Lift the Pop
Pin to slide

B

the back rest

Step 4. Assemble the Seat Pads

Seat Pad

2 - 3" bolts

C

2 - washers

1 2 3 4 5 6

page 11

S3.25 Leg Press Option Assembly Instructions

5. Route the Cable

As you route the Cable through the pulleys on the Leg
Press Option, wrench tighten the fasteners on each
pulley as you go. Make sure that the Cable slides freely
along the pulley (and beneath the cable retainer).
Make sure that you are using the correct Cable before
you tighten the fasteners.

Push the Pivot
Arm forward

C

Pivot Arm

A. Attach the barrel end of Cable 40538-101 to the

Seat Frame using
one 4-inch bolt
one washer
one locknut
Wrench tighten so that the barrel end of the Cable
rotates freely.

B. Loosen all the fasteners that attach the pulleys to

the Seat Frame.

C. Push the Pivot Arm forward so that the pulleys are

easily accessible.

D. Route the Cable around the pulley inside the Pivot

Arm Cover that is on the same side as the barrel
end of the Cable (see illustration). The Cable
should slide along the pulley beneath the cable
retainer. Wrench tighten this pulley’s fasteners.

E. You may need to slide the bolt out of the Pivot Arm

Cover to wrap the Cable around the pulley.

F. Continue to route the Cable around the pulleys as

shown in the illustration. Make sure that the Cable
slides freely along the pulleys (and beneath the
cable retainers) before you wrench tighten their
fasteners.

G. Wrap the Cable around the 4½-inch pulley (and

beneath its cable retainer) that is attached to the
Cross Brace. Wrench tighten.

1 - 4" bolt
1 - washer
1 - locknut

Loosen the pulley
fasteners

B

Pivot
Arm

Note: The Seat Pad is not shown.

1 2 3 4 5 6

A

Cable 40538-101

D

E

F

Seat Frame

Wrap the Cable around the
4½" pulley attached to the

G

Cross Brace

Step 5. Route the Cable

page 12

S3.25 Leg Press Option Assembly Instructions

6. Assemble the Cable and
Pulleys

You can identify Cables by the white numbers placed
at the end of the Cable.

Rear Upright

A. Place Leg Press Option Cable 40538-101 between

a cable retainer and one 3½-inch pulley. Attach the
pulley to the Lower Pulley Bracket located at the
base of the Rear Upright using
one 2-inch bolt
two washers
one locknut
Wrench tighten.

B. From the Top Beam, remove the surgical tube and

its fasteners.

Note: Discard the fasteners
one 3¼-inch bolt
one one-inch barrel spacer
two washers
one locknut

Cable Retainer

Lower Pulley Bracket

Attach this
end to the
Cable Tree

Cable 40538-101

3½" Pulley

Surgical
Tube

This end is
attached to the
Leg Press

1 - 2" bolt
2 - washers

A

1 - locknut

Note that no pulley is
attached to this bolt hole

B

Surgical
Tube

Cable Tree

Discard

1 - 3¼" bolt
1 - 1" barrel

spacer
2 - washers
1 - locknut

Step 6. Assemble the Cable and Pulleys

1 2 3 4 5 6

page 13

S3.25 Leg Press Option Assembly Instructions

C. Reattach the end of the original Surgical Tube from

the Cable Tree to its prior location and place the
new Surgical Tube that came with the Leg Press
Option to the outside of the Top Beam using
one 4-inch bolt
two washers
two ½-inch barrel spacers
one locknut
Wrench tighten.

C

New Surgical
Tube

1 - 4" bolt
2 - washers
2 - ½" barrel spacers
1 - locknut

D. Place the ball-end of Leg Press Option Cable 40538-

101 up through the Cable Tree and place
it securely in the U-clip.

E. Remove the buttonhead bolt and nylock nut from

the U-clip.

F. Attach the end of the original surgical tube to the

Cable Tree using the 1¼-inch buttonhead bolt and
thin nylock nut removed in Step 6E. Wrench
tighten.

Note: If you are assembling the Leg Press Option and
the S3.25 simultaneously, go to Step 21 in the

Assembly and Maintenance Guide

now.

S3.25

Original
Surgical Tube

Cable Tree

New Surgical
Tube

Cable Tree

1 - 1¼" button head bolt
1 - thin nylock nut

U-clip

Attach ball­end of Cable

D

to U-clip

Cable 40538-101

(from Leg Press)

E

1 2 3 4 5 6

Step 6. Assemble the Cable and Pulleys, Continued

page 14

S3.25 Leg Press Option Assembly Instructions

7. Replace the Shroud

A. Pick up the Shroud and fasteners from the location

where you left them in Step 4B.

B. Replace the Shroud by realigning the mounting

holes and inserting
six 2¾-inch bolts
six washers
six locknuts
Wrench tighten.

Top Beam

Notch in Shroud fits
around Top Beam
fastener

Replace Shroud

A

Step 7. Replace the Shroud

6 - 2¾" bolts
6 - washers

B

6 - locknuts

1 2 3 4 5 6

page 15

S3.25 Leg Press Option Assembly Instructions

4

After the Leg Press Option is assembled, you should
check the Cables for proper tension. These are some
obvious signs that cable problems exist:

✔ Excess slack exists in the Cable.

✔ The Top Cap Weight does not rest squarely on the

Weight Stack.

✔ The Cable rubs the inside edges of the pulleys.

CAUTION: Take the time to perform the following
steps. If the Cables do not have
the proper tension, you could damage the
machine and void the Precor Limited Warranty.

Note: To adjust the Selector Stem, refer to the

S3.25 Assembly and Maintenance Guide

Adjustments

.

1. Stretch the Cable

A

Chest Press Arms

Top Cap Weight

Top Weight

Weight Pin

C

B

Top Cap
Weight

A. Sometimes a new cable must be stretched so that

the Top Cap Weight rests on the Weight Stack. To
lengthen the Cable, insert the Weight Pin at a
comfortable weight level.

B. Push up on the Chest Press Arms, and then slowly

lower them.

C. Make sure the Top Cap Weight rests squarely on

the Weight Stack. If it does, no more adjustments
are needed, and the Leg Press Option is ready to
use. If the Top Cap Weight does not rest on the Top
Weight then further adjustments are needed.
Continue with steps 2 and 3.

Adjustments

1 2 3 4 5 6

page 16

S3.25 Leg Press Option Assembly Instructions

2. Rotate the Cam Washer

If the Top Cap Weight does not rest on the Top Weight,
you must make further adjustments.

A. Remove excess tension from the Cable by placing

the Weight Pin into the Selector Stem just under
the Top Cap Weight.

B. To tighten or loosen the Cable tension, rotate the

Cam Washer.

C. Look to see that Top Cap Weight rests squarely on

the Weight Stack. If it does, no more adjustments
are needed and the Leg Press Option is ready to
use. If the Top Cap Weight does not rest on the Top
Weight, then further adjustments are needed.
Continue with step 3.

Top Cap
Weight

Top Weight

Weight Pin

A

Rotate the

B

Cam Washer

Step 2. Rotate the Cam Washer

C

Top Cap
Weight

1 2 3 4 5 6

page 17

S3.25 Leg Press Option Assembly Instructions

3. Adjust the Rubber Bumper on
the Leg Press Option

If the Top Cap Weight still does not rest on the Top
Weight, you can make one final adjustment.

A. If the Cable tension still needs adjusting, push the

Pivot Arm up so that you can adjust the Rubber
Bumper on the Leg Press Option.

B. Rotate the Rubber Bumper up or down to tighten

or loosen the Cable tension.

Important: Tighten the locknut against the bracket
after you have properly adjusted the Cable tension.

C. Check the weights. Move the Weight Pin to each

Weight and Selector Stem location and replace the
Weight Pin in the Weight Stack.

With the slack removed from the Cables, you are now
ready to use the Leg Press Option. Thank you for
choosing Precor Strength-Training Equipment.

Adjust the

B

Rubber Bumper

Push the Pivot Arm up to adjust

A

the Rubber Bumper

Rubber Bumper

C

Note: For maintenance instructions, refer to your

Assembly and Maintenance Guide.

S3.25

Bracket

1 2 3 4 5 6

Step 3. Adjust the Rubber Bumper on the Leg Press Option

Weight Pin

Locknut

page 18

Thank You and Welcome to Precor

HERE

PLACE

STAMP

Fold along dotted line and tape closed prior to mailing.

local dealer or call Precor Customer Support at 800-347-4404.

If you have questions or need additional information, contact your

www.precor.com/warranty

YOU MAY ALSO REGISTER ONLINE AT

complete and return your warranty registration.

To allow us to serve you better, please take a few moments to

Precor Incorporated

20031 142nd Avenue NE

PO Box 7202

Woodinville, WA 98072-4002

RET.

page 19

❑ Precor reputation ❑ Print advertisement

❑ Prior use of Precor product(s) ❑ In-store display or demonstration

❑ Design/appearance ❑ Other

❑ Value for the price

❑ Special product features

❑ Rebate or sale price

❑ Quality/durability

❑ Warranty

❑ Physician recommendation

purchase your Precor product (choose up to three): ❑ Magazine advertisement or article

❑ Elliptical Fitness CrossTrainer (EFX

❑ Treadmill

❑ Mr.

❑ Mrs.

Gender: Marital status: Age: Annual household income: What are your fitness goals?

❑ Male ❑ Married ❑ Under 18 ❑ Under $50,000 ❑ Weight loss/management

What factors MOST influenced your decision to ❑ News report or product review

❑ Addition to equipment currently owned ❑ Physician

TELL US ABOUT YOUR PURCHASE

Purchase (check all that apply): How did you FIRST become aware of Precor

❑ First Precor product products (choose only one):

❑ Replaces a Precor product of the same type ❑ A gift

❑ Replaces same type of product – different brand ❑ Friend/relative

❑ Female ❑ Divorced ❑ 18-24 ❑ $51,000-75,000 ❑ Muscle tone enhancement

❑ Widowed ❑ 25-34 ❑ $76,000-100,000 ❑ Cardiovascular improvement

❑ Never been married ❑ 35-44 ❑ $101,000-150,000 ❑ Overall health

Your Email Address

Area Code

Street Address

Telephone

❑ Ms.

First Name

❑ Strength Training System

TELL US ABOUT YOU

from:

Please indicate the type of product purchased:

Purchased

Month

Day

Purchase:

Date of

TELL US ABOUT YOUR NEW PRECOR PRODUCT

❑ Fitness club

❑ Internet

❑ 45-54 ❑ $151,000+ ❑ Increase energy and flexibility

❑ 55-64 ❑ Stress reduction

❑ 65+ ❑ Rehabilitation

❑ Other

Zip CodeCity State

Middle Initial Last Name

Apt./Suite:

®

)

❑ StretchTrainer

❑ Cycle

❑ Stair Climber

TM

Dealer Name

Year

Product

Serial Number:

The serial number is located on the shipping box and on the product.

Effective 30 June 2002

P/N 45623-101

Please detach and mail in the warranty registration within ten days of purchase.

page 20

Precor Residential Equipment Limited Warranty

PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY BEFORE USING
YOUR PRECOR INCORPORATED PRODUCT. BY USING THE EQUIPMENT, YOU ARE
CONSENTING TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND CONDITIONS.

Limited Warranty.

Precor Incorporated warrants all new Precor products to be free from defects in materials and
manufacture for the warranty period set forth below. The warranty period commences on the
invoice date of original purchase. This warranty applies only against defects discovered within
the warranty period and extends only to the original purchaser of the product. Parts repaired or
replaced under the terms of this warranty will be warranted for the remainder of the original
warranty period only. To make claim under warranty, the buyer must notify Precor or their
authorized Precor dealer within 30 days after the date of discovery of any nonconformity and
make the affected product available for inspection by Precor or its service representative.
Precor’s obligations under this warranty are limited and set forth below.

Warranty Periods and Coverage

All residential products and commercial products used in the home are warranted for the
following periods:

• Lifetime frame and welds

• 10 years parts and wear items

• 1 year labor

• Coverage for options and accessories defined below.

Options / Accessories

Many options or accessories have components that are connected internally or mounted inside the
electronic console. The following guidelines determine the warranty for these components. If the
internal components are installed by the factory or by an authorized dealer as part of the original
sale and delivery, they have a warranty that is identical to the warranty of the equipment in which
they are connected or mounted. If the internal components are not installed by the factory or by an
authorized dealer as part of the original sale and delivery, they have a 90-day parts and labor
limited warranty. All components that are not internally connected have 90-day parts only limited
warranty. Satisfactory proof of purchase is required in all cases.

Conditions and Restrictions

This warranty is valid only in accordance with the conditions set forth below:

1. The warranty applies to the Precor product only while:
a. It remains in the possession of the original purchaser and proof of purchase is

demonstrated

b. It has not been subjected to accident, misuse, abuse, improper service, or non-Precor

modifications

c. Claims are made within the warranty period

2. This warranty does not cover damage or equipment failure caused by electrical wiring not in
compliance with electrical codes or Precor owner’s manual specifications, or failure to provide
reasonable and necessary maintenance as outlined in the owner’s manual.

Complete this portion and keep for your records.

Purchased From: ____________________________ Example: Dealer or store name.

Phone Number: _____________________________ Example: Dealer or store telephone number.

Product/model: _____________________________ Example: M9.31

Serial number: ______________________________ The serial number is found on the shipping container

3. Warranty of all Precor products applies to residential use only and is void when products are
used in a nonresidential environment or installed in a country other than where sold.

4. Except in Canada, Precor does not pay labor outside the United States.

5. Warranties outside the United States and Canada may vary. Please contact your local Dealer
for details.

This limited warranty shall not apply to:

1. Software version upgrades

2. Cosmetic items, including, but not limited to the following: grips, seats, and labels.

3. Repairs performed on Precor equipment missing a serial number or with a serial tag that has
been altered or defaced.

4. Service calls to correct installation of the equipment or instruct owners on how to use the
equipment.

5. Pickup, delivery, or freight charges involved with repairs.

6. Any labor costs incurred beyond the applicable labor warranty period.

Disclaimer and Release

The warranties provided herein are the exclusive warranties given by Precor and supersede any prior,
contrary or additional representations, whether oral or written. ANY IMPLIED WARRANTIES, INCLUDING THE

WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THAT APPLY TO ANY PARTS DESCRIBED ABOVE
ARE LIMITED IN DURATION TO THE PERIODS OF EXPRESS WARRANTIES GIVEN ABOVE FOR THOSE SAME PARTS. PRECOR
HEREBY DISCLAIMS AND EXCLUDES THOSE WARRANTIES THEREAFTER.

Some states do not allow limitation on how

long an implied warranty lasts, so the above limitation may not apply to you. PRECOR ALSO HEREBY DISCLAIMS

AND EXCLUDES ALL OTHER OBLIGATIONS OR LIABILITIES, EXPRESS OR IMPLIED, ARISING BY LAW OR OTHERWISE, WITH
RESPECT TO ANY NONCONFORMANCE OR DEFECT IN ANY PRODUCT, INCLUDING BUT NOT LIMITED TO: (A) ANY OBLIGATION,
LIABILITY, RIGHT, CLAIM OR REMEDY IN TORT, WHETHER OR NOT ARISING FROM THE NEGLIGENCE OF PRECOR OR ITS
SUPPLIERS (WHETHER ACTIVE, PASSIVE OR IMPUTED); AND (B) ANY OBLIGATION, LIABILITY, RIGHT, CLAIM, OR REMEDY FOR
LOSS OF OR DAMAGE TO ANY EQUIPMENT.

This disclaimer and release shall apply even if the express warranty set

forth above fails of its essential purpose.

Exclusive Remedies

For any product described above that fails to conform to its warranty, Precor will provide, at their option, one of
the following: (1) repair; (2) replacement; or (3) refund of the purchase price. Precor Limited Warranty service
may be obtained by contacting the authorized dealer from whom you purchased the item. Precor
compensates Servicers for warranty trips within their normal service area to repair equipment at the owner’s
location. You may be charged a trip charge outside the service area. THESE SHALL BE THE SOLE AND EXCLUSIVE

REMEDIES OF THE BUYER FOR ANY BREACH OF WARRANTY.

Exclusion of Consequential and Incidental Damages

PRECOR AND/OR ITS SUPPLIERS SHALL HAVE NO OBLIGATION OR LIABILITY, WHETHER ARISING IN CONTRACT
(INCLUDING WARRANTY), TORT (INCLUDING ACTIVE, PASSIVE, OR IMPUTED NEGLIGENCE AND STRICT LIABILITY), OR
OTHERWISE, FOR DAMAGE TO THE EQUIPMENT, PROPERTY DAMAGE, LOSS OF USE, REVENUE OR PROFIT, COST OF
CAPITAL, COST OF SUBSTITUTE EQUIPMENT, ADDITIONAL COST INCURRED BY BUYER (BY WAY OF CORRECTION OR
OTHERWISE) OR ANY OTHER INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, WHETHER
RESULTING FROM NONDELIVERY OR FROM THE USE, MISUSE OR INABILITY TO USE THE PRODUCT.

applies even if the above warranty fails of its essential purpose and regardless of whether such damages
are sought for breach of warranty, breach of contract, negligence, or strict liability in tort or under any other
legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation might not apply.

This warranty gives you specific legal rights, and you may also have other rights, which vary state
to state.

This exclusion

Effective 01 January 2003

P/N 36287-110

S3.25 Leg Press Option Specifications

Length: 60 inches (152 cm)

Height: 33 inches (84 cm)

Width: 30 inches (76 cm)

Shipping weight: 125 lb (57 kg)

Precor Incorporated
20031 142nd Avenue NE
P.O. Box 7202
Woodinville, WA USA 98072-4002

Precor and Pacific Fitness are registered trademarks of Precor Incorporated.
Specifications subject to change without notice.
Copyright 2003 Precor Incorporated.
Precor web site: www.precor.com

NOTICE:

Precor is widely recognized for its innovative, award winning designs of exercise equipment. Precor aggressively seeks U.S. and foreign patents for
both the mechanical construction and the visual aspects of its product design. Any party contemplating the use of Precor’s product designs is hereby
forewarned that Precor considers the unauthorized appropriation of its proprietary rights to be a very serious matter. Precor will vigorously pursue all
unauthorized appropriation of its proprietary rights.

S3.25 LPO Literature Kit # 44576-103

Leg Press Assembly Instructions # 44660-102

Exploded Views # 41829-103

Warranty Registration # 45623-101

Warranty Card # 36287-110

Effective date: April 30, 2003