Page 1
S3.25
Leg Press Option
Assembly Instructions
Page 2
S3.25 Leg Press Option Assembly Instructions
Important Safety Instructions
Before beginning any fitness program, you should
obtain a complete physical examination from your
physician.
Il est conseillé de subir un examen médical complet
avant d’entreprendre tout programme d’exercise. Si
vous avez des étourdissements ou des faiblesses,
arrêtez les exercices immédiatement.
When using exercise equipment, basic precautions
should always be taken, including the following:
• Read all instructions before using the Leg Press
Option. These instructions are written to ensure
your safety and to protect the unit.
• Do not allow children on or near the equipment.
• Use the equipment only for its intended
purpose as described in this guide. Do not
use accessory attachments that are not
recommended by the manufacturer: such
attachments might cause injuries.
• Wear proper exercise clothing and shoes for
your workout—no loose clothing.
• Use care when getting on or off the unit.
• Do not overexert yourself or work to
exhaustion.
• If you feel any pain or abnormal symptoms,
stop your workout immediately and consult
your physician.
• Never operate the unit when it has been dropped
or damaged. Return the equipment to a service
center for examination and repair.
• Never drop or insert objects into any opening
in the equipment. Keep hands away from moving
parts.
• Always check the unit and its cables before
each use. Make sure that all fasteners and
cables are secure and in good working
condition.
• Do not use the equipment outdoors.
Personal Safety During Assembly
• It is strongly recommended that a qualified dealer
assemble the equipment. Assistance is required.
• Read each step in the assembly instructions and
follow the steps in sequence. Do not skip ahead. If
you skip ahead, you may learn later that you have
to disassemble components and that you may have
damaged the equipment.
• Assemble and operate the Leg Press Option on a
solid, level surface. Locate the unit a few feet from
walls or furniture to provide easy access.
The Leg Press Option is designed for your enjoyment. By
following these precautions and using common sense,
you will have many safe and pleasurable hours of healthful
exercise with your Precor equipment.
Obtaining Service
Do not attempt to service the Leg Press
Option yourself. This unit does not contain
any user-serviceable parts.
For information about product operation or
service, check out the Precor web site at
www.precor.com or contact an authorized
Precor dealer or a Precor factory-authorized
service company. To locate the dealer or service
person nearest you, call 1-800-4-PRECOR.
If you call or e-mail Customer Service, have
your serial and part numbers available.
You can find the serial number printed on a
label on the Upright Seat Support of the Leg
Press Option. For future reference, write the
serial number in the space below.
Serial number: _____________
Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS
page 2
Page 3
S3.25 Leg Press Option Assembly Instructions
Table of Contents
Important Safety Instructions ............................................................... 2
Personal Safety During Assembly .................................................................................. 2
Obtaining Service .......................................................................................................... 2
Before You Begin ................................................................................... 4
1
2
3
Unpacking the Equipment .............................................................................................. 4
Preparations........................................................................................... 5
Required Tools ............................................................................................................... 5
Installation Requirements .............................................................................................. 5
Assembly Tips ............................................................................................................... 5
Assembly Instructions .......................................................................... 6
1. Remove the Shroud ................................................................................................... 7
2. Attach the Cross Brace to the S3.25 .......................................................................... 8
3. Assemble the Frame .................................................................................................. 9
4. Assemble the Seat Pads ............................................................................................ 11
5. Route the Cable ......................................................................................................... 12
6. Assemble the Cable and Pulleys ................................................................................ 13
7. Replace the Shroud ................................................................................................... 15
Table of Contents
4
Adjustments ........................................................................................... 16
1. Stretch the Cable ....................................................................................................... 16
2. Rotate the Cam Washer ............................................................................................. 17
3. Adjust the Rubber Bumper on the Leg Press Option .................................................. 18
Warranty Card ....................................................................... Back cover
Specifications ....................................................................... Back cover
page 3
Page 4
S3.25 Leg Press Option Assembly Instructions
1
Thank you for purchasing the Leg Press Option for
your Precor equipment. This option will add a new
dimension to your strength-training regimen. For
proper installation, please read this guide thoroughly
and follow the assembly instructions.
Unpacking the Equipment
The Leg Press Option is carefully tested and inspected
before shipment. Precor ships the unit in several pieces
that require assembly. Two people are required to
assemble this equipment. Ask for assistance during
the assembly process.
• Review the Installation Requirements on the
next page.
• Carefully unpack the pieces and lay them on
the floor near the place where you plan to use
the equipment.
If any items are missing, contact the dealer from whom
you purchased the unit or call 1-800-4-PRECOR to find
the dealer nearest you.
Before You Begin
Before You Begin
page 4
Page 5
S3.25 Leg Press Option Assembly Instructions
2
CAUTION: To set up this equipment, you will need
assistance. Do not attempt assembly by yourself.
You must review and follow the instructions in this
guide. If you do not assemble and use the Leg Press
Option according to the following guidelines, you could
void the Precor limited warranty.
Required Tools
You need to obtain these tools before assembling
the unit:
❑ ¾-inch socket wrench
❑ ¾-inch box-end wrench
❑ ⁹⁄₁₆-inch socket wrench
❑ ⁹⁄₁₆-inch box-end wrench
❑ Two adjustable pliers or crescent wrenches
❑ Standard set of metric Allen wrenches
❑ Utility knife or scissors
❑ Measuring tape
Preparations
Installation Requirements
Follow these installation requirements when
assembling the unit:
• Fill out and mail the limited warranty card.
The warranty card is found on the back cover of
this guide.
• Set up the Leg Press Option on a solid, flat
surface. A smooth, flat surface under the unit helps
keep it level. A level unit has fewer malfunctions.
• Provide ample space around the machine.
Open space around the machine allows for easier
access.
• Insert all bolts in the same direction. For
aesthetic purposes, insert all the bolts in the same
direction unless specified (in text or illustrations) to
do otherwise.
• Leave room for adjustments. Tighten fasteners
such as bolts, nuts, and screws, so that the unit is
stable, but leave room for adjustments. Do not fully
tighten fasteners until instructed in the assembly
steps to do so.
Assembly Tips
• A 6-inch scale is provided at the bottom of every
assembly instruction page. Use this scale to identify
the correct size bolts and spacers. The head of a
bolt is not used in measuring the length of a bolt.
To find out the length of a particular bolt, measure its
shank (the long, narrow part beneath the head). Refer
to the following diagram.
• Read all caution notes on each page before
completing that step.
Bolt head
Bolt threads
Shank
• Some pieces have extra holes that you will not use.
Use only those holes indicated in the instructions
and illustrations.
• While you may be able to assemble the Leg Press
Option by using the illustrations only, refer to the
text for important safety cautions and notes.
To determine the
length of a bolt,
measure its shank.
Preparations
page 5
Page 6
S3.25 Leg Press Option Assembly Instructions
Assembly
3
Assembly of the Leg Press Option takes professional
installers about 1 hour to complete. If this is the first time
you have assembled this type of equipment, plan on
significantly more time.
Professional installers are highly recommended!
CAUTION: Obtain assistance! Do not attempt
to assemble the Leg Press Option by yourself.
Because of the weight and size of the Leg Press
Option, you could be injured or damage the
equipment. Review the Installation Requirements
on page 5 before proceeding.
The Leg Press Option comes in one box. It can be
installed on either the S3.25 or S3.45 Precor Strength
Training Equipment. Note that the location where you
attach the Cross Brace to the Seat Frame differs.
As you read through the assembly instructions, be
sure that you are using the correct mounting holes for
your unit.
Instructions
Be careful to assemble the components in the
sequence presented in this guide.
Note: As with any assembled part, proper alignment and
adjustment is critical. While tightening the fasteners, be
sure to leave room for adjustments. Do not fully tighten the
fasteners until instructed to do so.
Assembly Instructions
1 2 3 4 5 6
page 6
Page 7
S3.25 Leg Press Option Assembly Instructions
1. Remove the Shroud
Important: For ease of assembly, the fasteners and
hardware for each step are labeled and packaged in
separate bags.
Note: If you are assembling the Leg Press Option along
with your S3.25, go directly to Step 2.
Before you can attach the Leg Press Option to the unit, you
must remove the Shroud.
A. Remove the Shroud by loosening and removing
six 2¾-inch bolts
six washers
six locknuts
Top Beam
Notch in Shroud fits
around Top Beam
fastener
B. Pull the Shroud away from the S3.25 and lay it and
its fasteners on the floor in a secure place.
Note: The top of the Shroud has a notch in it to
help you clear the Top Beam fastener.
6 - 2¾" bolts
6 - washers
A
6 - locknuts
Remove Shroud
B
1 2 3 4 5 6
Step 1. Remove the Shroud
page 7
Page 8
S3.25 Leg Press Option Assembly Instructions
2. Attach the Cross Brace to the
S3.25
Note: If you are assembling the Leg Press Option along
with the S3.25, you should complete Step 10 in the
S3.25 Assembly and Maintenance Guide before
attaching the Cross Brace.
A. Align the Cross Brace to the S3.25 Rear Upright
and secure it using
two 3-inch bolts
four washers
two locknuts
Wrench tighten.
Step 2. Attach the Cross Brace to the S3.25
2 - 3" bolts
4 - washers
A
2 - locknuts
1 2 3 4 5 6
Cross Brace
page 8
Page 9
S3.25 Leg Press Option Assembly Instructions
3. Assemble the Frame
A. With someone helping you, lift the Seat Frame
upright. Have your assistant hold it in place while you
attach the Cross Brace in the next step.
B. Attach the Cross Brace to the holes found at the
front of the Seat Frame using
two 3-inch bolts
four washers
two locknuts
Wrench tighten.
Backpad
Support
Backpad
Support
Pop Pin
C
Important: A label on the Seat Frame indicates the
mounting holes you must use to attach the Cross
Brace to the S3.25 Leg Press Option.
C. Slide the Backpad Support into the Seat Frame,
locking it in place with the Pop Pin.
Cross Brace
Label indicates mounting
location for the S3.25
B
2 - 3" bolts
4 - washers
2 - locknuts
Have an assistant hold
the Seat Frame stable
A
and upright while you
attach the Cross Brace
Seat Frame
Step 3. Assemble the Frame
1 2 3 4 5 6
page 9
Page 10
S3.25 Leg Press Option Assembly Instructions
D. Assemble the Footrest by resting the Pivot Arm
on the Rubber Bumper. Make sure that the red
arrow on the back of the Footrest points toward
the ceiling.
E. Attach the Footrest to the Pivot Arm and Pivot
Tube using
two large ½-inch by 3-¼-inch bolts
four ½-inch-diameter washers
two large ½-inch locknuts
Wrench tighten enough to allow free movement of
the Pivot Arm.
F. Attach the Handle to the Seat Frame using
two 3-inch bolts
four washers
two locknuts
Wrench tighten.
Footrest
Pivot Arm
Handle
2 - large ½" x 3¼" bolts
4 - ½" diameter washers
E
2 - large ½" lock nuts
2 - 3" bolts
4 - washers
F
2 - locknuts
Pop Pin
Step 3. Assemble the Frame, Continued
Footrest
Red Arrow Label
Pivot Arm
Pivot Tube
Rest the Pivot Arm on the
D
Rubber Bumper
Rubber Bumper
1 2 3 4 5 6
Seat Frame
page 10
Page 11
S3.25 Leg Press Option Assembly Instructions
4. Assemble the Seat Pads
A. Attach one of the Seat Pads to the Seat Bracket
Support using
two 1¼-inch bolts
two washers
Wrench tighten.
B. Lift the Pop Pin and slide the Seat Pad out of the
way to assemble the other Seat Pad.
C. Attach the remaining Seat Pad to the Seat Frame
using
two 3-inch bolts
two washers
Wrench tighten.
Note: Make sure that the seams on the Seat Pads
face down toward the frame.
Note: If you are assembling the Leg Press Option and
the S3.25 simultaneously, return to Step 11 in the
S3.25 Assembly and Maintenance Guide now.
Seat Pad
used as a
back rest
Seat Bracket Support
Handle
Seat Frame
2 - 1¼" bolts
2 - washers
A
Lift the Pop
Pin to slide
B
the back rest
Step 4. Assemble the Seat Pads
Seat Pad
2 - 3" bolts
C
2 - washers
1 2 3 4 5 6
page 11
Page 12
S3.25 Leg Press Option Assembly Instructions
5. Route the Cable
As you route the Cable through the pulleys on the Leg
Press Option, wrench tighten the fasteners on each
pulley as you go. Make sure that the Cable slides freely
along the pulley (and beneath the cable retainer). Make
sure that you are using the correct Cable before you
tighten the fasteners.
Push the Pivot
Arm forward
C
Pivot Arm
A. Attach the barrel end of Cable 40538-101 to the
Seat Frame using
one 4-inch bolt
one washer
one locknut
Wrench tighten so that the barrel end of the Cable
rotates freely.
B. Loosen all the fasteners that attach the pulleys to
the Seat Frame.
C. Push the Pivot Arm forward so that the pulleys are
easily accessible.
D. Route the Cable around the pulley inside the Pivot
Arm Cover that is on the same side as the barrel
end of the Cable (see illustration). The Cable
should slide along the pulley beneath the cable
retainer. Wrench tighten this pulley’s fasteners.
E. You may need to slide the bolt out of the Pivot Arm
Cover to wrap the Cable around the pulley.
F. Continue to route the Cable around the pulleys as
shown in the illustration. Make sure that the Cable
slides freely along the pulleys (and beneath the
cable retainers) before you wrench tighten their
fasteners.
G. Wrap the Cable around the 4½-inch pulley (and
beneath its cable retainer) that is attached to the
Cross Brace. Wrench tighten.
1 - 4" bolt
1 - washer
1 - locknut
Loosen the pulley
fasteners
B
Pivot
Arm
Note: The Seat Pad is not shown.
1 2 3 4 5 6
A
Cable 40538-101
D
E
F
Seat Frame
Wrap the Cable around the
4½" pulley attached to the
G
Cross Brace
Step 5. Route the Cable
page 12
Page 13
S3.25 Leg Press Option Assembly Instructions
6. Assemble the Cable and
Pulleys
You can identify Cables by the white numbers placed at
the end of the Cable.
Rear Upright
A. Place Leg Press Option Cable 40538-101 between a
cable retainer and one 3½-inch pulley. Attach the
pulley to the Lower Pulley Bracket located at the
base of the Rear Upright using
one 2-inch bolt
two washers
one locknut
Wrench tighten.
B. From the Top Beam, remove the surgical tube and
its fasteners.
Note: Discard the fasteners
one 3¼-inch bolt
one one-inch barrel spacer
two washers
one locknut
Cable Retainer
Lower Pulley Bracket
Attach this
end to the
Cable Tree
Cable 40538-101
3½" Pulley
Surgical
Tube
This end is
attached to the
Leg Press
1 - 2" bolt
2 - washers
A
1 - locknut
Note that no pulley is
attached to this bolt hole
Discard
1 - 3¼" bolt
B
1 - 1" barrel
2 - washers
1 - locknut
Surgical
Tube
Cable Tree
spacer
Step 6. Assemble the Cable and Pulleys
1 2 3 4 5 6
page 13
Page 14
S3.25 Leg Press Option Assembly Instructions
C. Reattach the end of the original Surgical Tube from
the Cable Tree to its prior location and place the new
Surgical Tube that came with the Leg Press Option
to the outside of the Top Beam using
one 4-inch bolt
two washers
two ½-inch barrel spacers
one locknut
Wrench tighten.
C
New Surgical
Tube
1 - 4" bolt
2 - washers
2 - ½" barrel spacers
1 - locknut
D. Place the ball-end of Leg Press Option Cable 40538-
101 up through the Cable Tree and place
it securely in the U-clip.
E. Remove the buttonhead bolt and nylock nut from
the U-clip.
F. Attach the end of the original surgical tube to the
Cable Tree using the 1¼-inch buttonhead bolt and
thin nylock nut removed in Step 6E. Wrench tighten.
Note: If you are assembling the Leg Press Option and
the S3.25 simultaneously, go to Step 21 in the S3.25
Assembly and Maintenance Guide now.
Original
Surgical Tube
Cable Tree
New Surgical
Tube
Cable Tree
1 - 1¼" button head bolt
1 - thin nylock nut
U-clip
Attach ballend of Cable
D
to U-clip
Cable 40538-101
(from Leg Press)
E
1 2 3 4 5 6
Step 6. Assemble the Cable and Pulleys, Continued
page 14
Page 15
S3.25 Leg Press Option Assembly Instructions
7. Replace the Shroud
A. Pick up the Shroud and fasteners from the location
where you left them in Step 4B.
B. Replace the Shroud by realigning the mounting
holes and inserting
six 2¾-inch bolts
six washers
six locknuts
Wrench tighten.
Top Beam
Notch in Shroud fits
around Top Beam
fastener
Replace Shroud
A
Step 7. Replace the Shroud
6 - 2¾" bolts
6 - washers
B
6 - locknuts
1 2 3 4 5 6
page 15
Page 16
S3.25 Leg Press Option Assembly Instructions
4
After the Leg Press Option is assembled, you should
check the Cables for proper tension. These are some
obvious signs that cable problems exist:
✔ Excess slack exists in the Cable.
✔ The Top Cap Weight does not rest squarely on the
Weight Stack.
✔ The Cable rubs the inside edges of the pulleys.
CAUTION: Take the time to perform the following
steps. If the Cables do not have
the proper tension, you could damage the
machine and void the Precor Limited Warranty.
Note: To adjust the Selector Stem, refer to the
S3.25 Assembly and Maintenance Guide.
Adjustments
1. Stretch the Cable
A
Chest Press Arms
Top Cap Weight
Top Weight
Weight Pin
C
B
Top Cap
Weight
A. Sometimes a new cable must be stretched so that
the Top Cap Weight rests on the Weight Stack. To
lengthen the Cable, insert the Weight Pin at a
comfortable weight level.
B. Push up on the Chest Press Arms, and then slowly
lower them.
C. Make sure the Top Cap Weight rests squarely on
the Weight Stack. If it does, no more adjustments
are needed, and the Leg Press Option is ready to
use. If the Top Cap Weight does not rest on the Top
Adjustments
1 2 3 4 5 6
page 16
Page 17
S3.25 Leg Press Option Assembly Instructions
Weight then further adjustments are needed.
Continue with steps 2 and 3.
2. Rotate the Cam Washer
If the Top Cap Weight does not rest on the Top Weight,
you must make further adjustments.
A. Remove excess tension from the Cable by placing
the Weight Pin into the Selector Stem just under the
Top Cap Weight.
B. To tighten or loosen the Cable tension, rotate the
Cam Washer.
C. Look to see that Top Cap Weight rests squarely on
the Weight Stack. If it does, no more adjustments are
needed and the Leg Press Option is ready to use. If
the Top Cap Weight does not rest on the Top
Weight, then further adjustments are needed.
Continue with step 3.
Top Cap
Weight
Top Cap
Weight
Top Weight
Weight Pin
A
C
Rotate the
B
Cam Washer
Step 2. Rotate the Cam Washer
1 2 3 4 5 6
page 17
Page 18
S3.25 Leg Press Option Assembly Instructions
3. Adjust the Rubber Bumper on
the Leg Press Option
If the Top Cap Weight still does not rest on the Top
Weight, you can make one final adjustment.
A. If the Cable tension still needs adjusting, push the
Pivot Arm up so that you can adjust the Rubber
Bumper on the Leg Press Option.
B. Rotate the Rubber Bumper up or down to tighten or
loosen the Cable tension.
Important: Tighten the locknut against the bracket
after you have properly adjusted the Cable tension.
C. Check the weights. Move the Weight Pin to each
Weight and Selector Stem location and replace the
Weight Pin in the Weight Stack.
With the slack removed from the Cables, you are now
ready to use the Leg Press Option. Thank you for
choosing Precor Strength-Training Equipment.
Note: For maintenance instructions, refer to your S3.25
Assembly and Maintenance Guide.
Adjust the
B
Rubber Bumper
Push the Pivot Arm up to adjust
A
the Rubber Bumper
Rubber Bumper
C
Bracket
1 2 3 4 5 6
Step 3. Adjust the Rubber Bumper on the Leg Press Option
Weight Pin
Locknut
page 18
Page 19
Residential Equipment Limited Warranty
Precor Incorporated warrants that all new Precor products are free of manufacturing defects in
workmanship and materials. Parts repaired or replaced under the terms of this warranty will be
warranted for the remainder of the original warranty period only. This warranty becomes effective
at the invoice date of the original purchase.
Elliptical Fitness Crosstrainers and Motorized Treadmills (excluding EFX5.17 and
Treadmills: 9.2 and 9.4 series) — Labor is covered for one year, parts are covered for five years
plus a lifetime frame weld warranty covering parts-only repair or replacement parts. (Labor is not
covered on frame replacement after one year.)
Products (StretchTrainer, Strength Equipment — formerly Pacific Fitness) other than
Elliptical Fitness Crosstrainer and Motorized Treadmills (except options)
StretchTrainer — Labor is covered for a period of 90 days, parts are covered for a period of one year
plus a lifetime frame weld warranty covering parts-only repair or replacement parts. (Labor is not covered on
frame replacement after one year.)
Pacific Fitness Branded Strength Products and Precor Strength Products S3.xx
This is a parts only warranty. Labor costs are not covered.
1. Frame & Welds: Defective parts pertaining to frame structure, including all welded assembly
parts, will be warranted for Lifetime.
2. Bearings, Guide rods, Cams, Pulleys, Belts, Cables, Hand grips, and Miscellaneous parts will be
warranted for a period of three years. Note that for the Precor Strength Products S3.xx, and
the Pacific Fitness Solana and Zuma, the warranted period is five years.
3. Upholstery will be warranted for a period of one year. A three month warranty applies to
Naugahyde upholstery for Pacific Fitness Branded Strength Products only.
Return Policy: Proof of purchase is required to determine whether service on a Precor Strength Product/
Pacific Fitness Product during its warranty period will commence. Claims should be made to the dealer
from whom you purchased the product. The purchaser is responsible for all transportation and insurance
costs on returned or replaced equipment or parts. The purchaser also assumes any costs associated with
the disassembling or reassembling of the replacement parts. WARRANTY BECOMES VOID IF PRECOR
FINDS THE DEFECT A RESULT OF INCORRECT INSTALLATION, MISUSE, LACK OF PROPER MAINTENANCE OR ANY MODIFICATION NOT APPROVED BY PRECOR.
Options / Accessories / Battery-powered or Self-Operated Devices
Many options or accessories have components that are connected internally or mounted inside
the electronic console. The following guidelines determine the warranty for these components. If
the internal components are installed by the factory or by an authorized dealer as part of the
original sale and delivery, they have a warranty that is identical to the warranty of the equipment
in which they are connected or mounted. If the internal components are not installed by the
factory or by an authorized dealer as part of the original sale and delivery, they have a 90 days
parts and labor limited warranty. All components that are not internally connected have a 90 days
parts only limited warranty. Satisfactory proof of purchase is required in all cases.
PRECOR'S SOLE LIABILITY IS LIMITED TO REPAIR OR REPLACEMENT OF PARTS ACCORDING TO
THE TERMS AND CONDITIONS OF THESE LIMITED WARRANTIES, AND ANY IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION
OF THE ABOVE WRITTEN WARRANTIES. IN NO EVENT WILL PRECOR OR THE SELLING DEALER BE
LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES SUCH AS INCONVENIENCE, COMMERCIAL
LOSS, LOST PROFITS OR DAMAGE TO OTHER PROPERTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
Keep this for your records. Purchased From:
Phone Number: Product/Model:
Serial #:
Effective 01 August 2001
P/N 36287-108
Conditions
This warranty is valid only in accordance with the
conditions set forth below.
1. Warranty applies to the Precor product only while
A) it remains in the possession of the original
purchaser and proof of purchase is demonstrated,
B) it has not been subjected to accident, misuse,
abuse, improper service, or non-Precor modification
and C) claims are made within the warranty period.
2. Warranty of all Precor products applies to residential
use only (unless specifically stated by the factory, in
writing, to be warranted for commercial use) and is void
when products are used in a non-residential environment or installed in a country other than where sold.
3. This warranty does not cover damage or equipment
failure caused by residential wiring not in compliance
with electrical codes or Precor owner’s manual
specifications, or failure to provide reasonable and
necessary maintenance as outlined in the owner's
manual.
4. During the labor period Precor compensates
Servicers for warranty trips within their normal
service area to repair motorized treadmills and
elliptical fitness crosstrainers at the customer’s
location. You may be charged a trip charge outside
the service area, or for on-site warranty repairs, or
for on-site warranty repairs of strength products,
within the service area.
5. Precor Limited Warranty service may be obtained
by contacting the authorized dealer from where
you purchased the equipment or by contacting a
Precor Factory Authorized Service Center, or by
calling 1-800-4-PRECOR (1-800-477-3267).
6. Except in Canada, Precor does not pay labor outside
the United States. Equipment limited warranty is
void when equipment is installed in a country other
than where sold. For specific warranty details,
contact a local Precor dealer.
This Limited Warranty shall not apply to:
1. Software (PROM) limitations or corrections.
2. Batteries or other consumables, or cosmetic
items, grips, seats, labels, or wheels.
3. Repairs performed on Precor equipment missing a
serial number or with a serial tag that has been altered
or defaced.
4. Service calls to correct installation of the equipment
or instruct owners on how to use the equipment.
5. Pick-up, delivery, or freight charges involved with repairs.
6. Any labor costs incurred beyond the applicable labor
warranty period.
Please fill out the Warranty Registration and
mail it to Precor.
▼
Name of Facility
Contact Person
Phone Number
Address
City State Zip Code
Purchased From
City State Zip Code
Serial #
Purchaser's Signature ____________________________________________________________
Mr.
Ms.
Please detach and return this portion.
Serial number is located on the shipping box and on the product.
–
–
–
event of a safety modification or for other reasons Precor might deem necessary, we will contact you directly.
20___; further, that the undersigned has read and understands the conditions and terms of the Precor Limited Warranty in its entirety. For
your protection, complete the Precor Limited Warranty registration card within 10 days from date of purchase and mail it to Precor. In the
The undersigned hereby acknowledges receipt of the Precor Limited Warranty and affirms that the date of purchase was_____________
Residential Equipment Limited Warranty
Thank you for purchasing a PRECOR product. In order that we may continue to serve you in the future, please take a few minutes to
complete and return this warranty registration.
Page 20
Please fill out the Warranty Registration and
mail it to Precor.
S3.25 Leg Press Option Specifications
Length: 60 inches (152 cm)
Height: 33 inches (84 cm)
Width: 30 inches (76 cm)
▼
Warranty Registration Card
Precor Incorporated
20031 142nd Avenue NE
P.O. Box 7202
Woodinville, WA USA 98072-4002
Shipping weight: 125 lb (57 kg)
Precor Incorporated
20031 142nd Avenue NE
P.O. Box 7202
Woodinville, WA USA 98072-4002
Precor and Pacific Fitness are registered trademarks of Precor Incorporated.
Specifications subject to change without notice.
Copyright 2001 Precor Incorporated. Precor web site: www.precor.com
STAMP
HERE
PLACE
NOTICE:
Precor is widely recognized for its innovative, award winning designs of exercise
equipment. Precor aggressively seeks U.S. and foreign patents for both the mechanical
construction and the visual aspects of its product design. Any party contemplating the use
of Precor’s product designs is hereby forewarned that Precor considers the unauthorized
appropriation of its proprietary rights to be a very serious matter. Precor will vigorously
pursue all unauthorized appropriation of its proprietary rights.
S3.25 LPO Literature Kit # 44659-102
Leg Press Assembly Instructions # 44660-102
Exploded Views # 44661-101
Warranty Card # 36287-108
Effective date: September 10, 2001
Loading...