Powermatic DS20 User Manual

Operating Instructions and Parts Manual

20-inch Disc Sander

Model DS20

Three Phase model shown

WALTER MEIER (Manufacturing) Inc.

427 New Sanford Road LaVergne, TN 37086 Part No. M-0460226

Warranty and Service

Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these Walter Meier Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and major repair on your POWERMATIC® tools. For the name of an Authorized Service Center in your area call 1-800-274-6848.

MORE INFORM ATION

Walter Meier is consistently adding new products to the line. For complete, up-to-date product information, check with your local Walter Meier distributor, or visit powermatic.com.

WARRANTY

POWERMATIC products carry a limited warranty which varies in duration based upon the product.

WHAT IS COVERED?

This warranty covers any defects in workmanship or materials subject to the except ions stated below. Cutting tools, abrasives and other consumables are excluded from warranty coverage.

WHO IS COVERED?

This warranty covers only the initial purchaser of the product.

WHAT IS THE PERIOD OF COVERAGE?

The general POWERM ATIC warranty lasts for the time period specified in the product literature of each product.

WHAT IS NOT COVERED?

The Five Year Warranty does not cover products used for commercial, industrial or educational purposes. Products w ith a Five Year Warranty that are used for commercial, industrial or education purposes revert to a One Year Warranty. This warranty does not cover defects due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-and-tear, improper repair or alterations, or lack of maintenance.

HOW TO GET SERVICE

The product or part must be returned for examination, postage prepaid, to a location designated by us. For the name of the location nearest you, please call 1-800-274-6848.

You must provide proof of initial purchase date and an explanation of the complaint must accompany the merchandise. If our inspect ion discloses a defect, we will repair or rep lace the product, or refund the purchase price, at our option.

We w ill return the repaired product or replacement at our expense unless it is determined by us that there is no defect, or that the defect resulted from causes not within the scop e of our warranty in which case we will, at your direction, dispose of or return the product. In the event you choose to have the product returned, you will be responsible for the handling and shipping costs of the return.

HOW STATE LAW APPLIES

This warranty gives you specific legal rights; you may also have other rights which vary from state to state.

LIMITATIONS ON THIS WARRANTY

WALTER MEIER (MANUFACTURING) INC., LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR EACH PRODUCT. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OR MERCHANTABILITY AND FITNESS ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG THE IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

WALTER MEIER (MANUFACTURING) INC., SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

Walter Meier sells through distributors only. The specifications in Walter Meier catalogs are given as general information and are not binding. M embers of Walter Meier reserve the right to effect at any time, without prior notice, those alterat ions to parts, fittings, and accessory equipment which they may deem necessary for any reason whatsoever.

Table of Contents

Warranty and Service..........................................................................................................................2

Table of Contents ...............................................................................................................................3

Warning .............................................................................................................................................4

Introduction ........................................................................................................................................6

Specifications .....................................................................................................................................6

Unpacking ..........................................................................................................................................6

Installation..........................................................................................................................................7

Attaching Sanding Paper .................................................................................................................7

Mounting the Brake Assembly ..........................................................................................................7

Dust Collection ................................................................................................................................8

Grounding Instructions ........................................................................................................................8

Extension Cords ..............................................................................................................................9

On-Off Switch Padlock .....................................................................................................................9

Adjustments ..................................................................................................................................... 10

Table Movement ........................................................................................................................... 10

Squaring the Table ........................................................................................................................ 10

Replacing Abrasive Disc ................................................................................................................ 10

Miter Gauge .................................................................................................................................. 11

Operation ......................................................................................................................................... 11

Forward-Reverse........................................................................................................................... 12

Brake............................................................................................................................................ 12

Replacement Parts ........................................................................................................................... 14

Parts List: DS20 Disc Sander ......................................................................................................... 15

Exploded View: DS20 Disc Sander ................................................................................................. 17

Parts List: Brake Assembly ............................................................................................................ 18

Electrical Connections....................................................................................................................... 19

Warning

1. Read and understand the entire owner’s manual before attempting assembly or operation.

2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury.

3. Replace the warning labels if they become obscured or removed.

4. This disc sander is designed and intended for use by properly trained and experienced personnel only. If you are not familiar wit h the proper and safe operation of a disc sander, do not use until proper training and knowledge have been obtained.

5. Do not use this disc sander for other than its intended use. If used for other purposes, Walter Meier (Manufacturing) Inc., disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use.

6. Always wear approved safety glasses/face shields while using this disc sander. Everyday eyeglasses only have impact resistant lenses; they are not safety glasses.

7. Before operating this disc sander, remove tie, rings, watches and other jewelry, and roll sleeves up past the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips are recommended. Do not wear gloves.

8. Wear ear protectors (plugs or muffs) during extended periods of operation.

9. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.

10. Make certain the switch is in the OFF position before connecting the machine to the power supply.

11. Make certain the machine is properly grounded.

12. Make all machine adjustments or maintenance with the machine unplugged from the power source.

13. Some d ust created by power sanding, sawing, grinding, drilling and other construction activities contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• Lead from lead based paint.

• Crystalline silica from bricks, cement and other masonry products.

• Arsenic and chromium from chemically treated lumber.

Your risk of exposure varies, depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area and work with approved safety equipment, such as face or dust masks that are specifically designed to filter out microscopic particles.

14. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting wrenches are removed from the machine before turning it on.

15. Keep safety guards in place at all times when the machine is in use. If removed for maintenance purposes, use extreme caution and replace the guards immediately.

16. Check damaged parts. Before further use of the machine, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

17. Provide for adequate space surrounding work area and non-glare, overhead lighting.

18. Keep the floor around the machine clean and free of scrap material, oil and grease.

19. Keep visitors a safe distance from the work area. Keep children away.

20. Make your workshop child proof with padlocks, master switches or by removing starter keys.

21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury.

22. Maintain a balanced stance at all times so that you do not fall or lean against the disc or other moving parts. Do not overreach or use excessive force to perform any machine operation.

23. Support the workpiece with the miter gauge; maintain control of the workpiece at all times.

24. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for which it was not desig ned. The right tool will do the job better and safer.

25. Use recommended accessories; improper accessories may be hazardous.

26. Maintain tools with care. Follow instructions for lubricating and changing accessories.

27. Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do not us e your hands.

28. Do not stand on the machine. Serious injury could occur if the machine tips over.

29. Never leave the machine running unattended. Turn the power off and do not leave the machine until it comes to a complete stop.

30. Remove loose items and unnecessary work pieces from the area before starting the machine.

31. After turning switch to “O N,” always allow the disc to come up to full speed before sanding or grinding. Keep hands clear of the disc.

32. Do not wet grind or polish. Never use a steady stream of water on the workpiece. Only quench the workpiece in water to cool it.

33. Do not grind or polish magnesium as it may catch on fire.

34. Replace sanding discs when they become loaded and glazed or frayed.

Familiarize yourself with the following safety notices used in this manual:

This means that if precautions are not heeded, it may result in minor injury and/or

possible machine damage.

This means that if precautions are not heeded, it may result in serious injury or possibly

even death.

Introduction

This manual is provided by Walter Meier (Manufact uring) Inc., covering the safe operation and maintenance procedures for a Powermatic Model DS20 Disc Sander. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to provide years of trouble free operation if used in accordance with instructions set forth in this manual. If there are any questions or comments, please contact either your local supplier or Walter Meier. Walter Meier can also be reached at our web site: www.waltermeier.com.

Specifications

Model Number ............................................................................................................................. DS20

Stock Number (3HP, 3Ph, 230/460V – prewired 230V) ...............................................................1791264

Stock Number (2HP, 1Ph, 230V) ..............................................................................................1791276

Disc Diameter (in.) ............................................................................................................................ 20

Table Tilt (deg.) ............................................................................................................. 30 up, 45 down

Table Size (in.) .............................................................................................................. 27-1/2 x 10-1/2

Table Surface from Floor, minimum height (in.) ........................................................................... 28-3/16

Table Surface from Floor, maximum height (in.) ............................................................................ 35-7/8

Distance Between Disc and Table (in.) ............................................................................................ 0.20

Distance Between Mounted Abrasive and Table (in.)........................................................................ 0.17

Dust Port Diameter (in.)....................................................................................................................... 4

Dust Collection Minimum CFM Required .......................................................................................... 600

Disc Speed (RPM) ....................................................................................................................... 1,720

Overall Size (LxWxH)(in.) .............................................................................................. 31 x 28 x 48-1/2

Footprint (LxW)(in.) ........................................................................................................ 22-1/2 x 22-1/2

Net Weight, approximate (lbs.)......................................................................................................... 426

Shipping Weight, approximate (lbs.) ................................................................................................. 529

The above specifications were current at the time this manual was published, but because of our policy of continuous improvement, Walter Meier reserves the right to change specifications at any time and without prior notice, without incurring obligations.

Unpacking

Open shipping container and check for shipping damage. Report any damage immediately to your distributor and shipping agent. Do not discard any shipping material until the Disc Sander is installed and running properly. Read the instruction manual t horoughly for assembly, maintenance and safety instructions.

Contents of shipping container:

1 DS20 Disc Sander 1 20” Abrasive Paper 1 Brake Assembly 1 Instruction and Parts Manual 1 Warranty Card

+ 13 hidden pages