Thank you for purchasing this Portable PA system. To gain the most benefit fromt his PA system and its sophisticated functions, you need t read through this manual thoroughly. Keep it in a safe place for future reference.
Features
|
|
Main Features: |
|
P-12A & P-15A |
|
P-12AUI & P-15AUI |
|
|
|
|
|||
|
|
|
|
|||
|
|
Tri-Pod, Flyable, & Floor Mounting Configuration |
|
1,000W Max Power/400W RMS Class D Amplifier(12”) |
|
USB Flash Drive Input |
|
|
IMPP Vented Plastic Cabinet |
|
1,200W Max Power/500W RMS Class D Amplifier(15”) |
|
Playback Controls & LCD Display |
|
|
2” Voicw Coil Woofer (12”) |
|
2 Ch. XLR Mic & Line Input |
|
iPod Input w/ Charging |
|
|
2.5” Voicw Coil Woofer (15”) |
|
Stereo RCA & Phono Line Input |
* Other specifications same as P-12A/P-15A |
|
|
|
1” Compression Driver |
|
Mic & XLR Line-in Gain Control |
|
|
|
|
35-20kHz Frequency Response (12”) |
|
2-Band Equalizer |
|
|
|
|
35-20kHz Frequency Response (15”) |
|
|
|
|
|
|
98dB (1w/1m) Sensitivity (12”) |
|
|
|
|
|
|
101dB (1w/1m) Sensitivity (15”) |
|
|
|
|
|
|
23.4”h x 15.1”w x 13.7”d; 35.2lbs (12”) |
|
|
|
|
|
|
27.6”h x 18.1”w x 16.3”d; 44lbs (15”) |
|
|
|
|
|
|
|
|
|
|
|
CAUTION:
WARNING:
TO REDUCE THE RISK OF FIRE REPLACE WITH ONLY SAME TYPE AND RATING OF FUSE
TO REDUCE THE RISK OF FIRE OR ELECTRICS DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated ‘dangerous voltage’ within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
Read these instructions. Keep these instructions. Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury
from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
PRECAUTIONS
WARNING
PLEASE READ CAREFULLY BEFORE PROCEEDING
Please keep this manual in a safe place for future reference.
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
Power supply/Power cord
Only use the voltage specified as correct for the device. The required voltage is printed on the name plate of the device.
Use only the included power cord.
Do not place the power cord near heat sources such as heaters or radiators, do not excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it.
Be sure to connect to an appropriate outlet with a protective grounding connection. Improper grounding can result in electrical shock
Do not open
Do not open the device or attempt to disassemble the internal parts or modify them in any way. The device contains no user-serviceable parts. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified service personnel.
Water warning
Do not expose the device to rain, use it near water or in damp or wet conditions, or place containers on it containing liquids which might spill into any openings.
Never insert or remove an electric plug with wet hands.
If you notice any abnormality
If the power cord or plug becomes frayed or damaged, there is a sudden loss of sound during use of the device, or any unusual smells or smoke should appear, turn off the power switch, disconnect the electric plug from the outlet immediately, and have the device inspected by qualified service personnel.
If this device is dropped or damaged, immediately turn off the power switch, disconnect the electric plug from the outlet, and have the device inspected by qualified service personnel.
1
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following:
Power supply/Power cord
Remove the electric plug from the outlet when the devices is not to be used for extend periods of time, or during electrical storms.
When removing the electric plug from the device or an outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it.
Location
When transporting or moving the device, always use two or more people. Attempting to lift the device by yourself may damage your back, result in other injury, or cause damage to the device itself.
Before moving the device, remove all connected cables.
When setting up the device, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet.
Do not use the device in a confined, poorly ventilated location. Make sure that there is adequate space between the mixer and surrounding walls or other devices: at least 1’ ft. at the side, 1’ ft. behind and 1’ ft. above. If the mixer is to be used installed into the speaker cabinet, make sure to allow adequate space between the speaker and the surrounding walls or other devices: at least 1’ ft. at the sides, 1’ ft. behind and 1’ ft. above. Inadequate ventilation can result in overheating, possibly causing damage to the device(s), or even fire.
Do not use the speaker’s handles for suspended installation. Doing so could result in damage or personal injury.
Avoid setting all equalizer controls and faders to their maximum. Depending on the condition of the connected devices, doing so may cause feedback and may damage the speakers.
Do not expose the device to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel disfiguration or damage to the internal components.
Do not place the device in an unstable position where it might accidentally fall over.
Do not block the vents. This mixer has ventilation holes at the top to prevent the internal temperature from becoming too high. In particular, do not place the device on its side or upside down. Inadequate ventilation can result in overheating, possibly causing damage to the device(s), or even fire.
Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Doing so may result in noise, both in the device itself and in the TV or radio next to it.
IMPORTANT
Please record the serial number of this unit in the space below.
Model:
Serial No.:
The serial number is located on the bottom or rear of the unit. Retain this Owner’s Manual in a safe place for future reference.
Connections
Before connecting the device to other devices, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum.
For the SPEAKERS jacks, Use only the included speakers and speakers cables. Use of other types of speakers and cables may result in damage to the device(s), or even fire.
Handling Precautions
When turning on the AC power in your audio system, always turn on the device LAST, to avoid speaker damage. When turning the power off, the device should be turned off FIRST for the same reason.
Do not insert your fingers or hands in any gaps or openings on the device (vents, ports, etc.).
Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any gaps or openings on the device (vents, ports, etc.). If this happens, turn off the power immediately and unplug the power cord from the AC outlet. Then have the device inspected by qualified service personnel.
Do not use the device for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician immediately.
Do not operate the device if the sound is distorting. Prolonged use in this condition could cause overheating and result in fire.
Do not rest your weight on the device or place heavy objects on it, and avoid use excessive force on the buttons, switches or connectors.
Protective Circuit (poly switch)
All full-range loudspeakers are fitted with a self-resetting poly switch that protects the high-frequency driver from damage caused by excessive power. If a loudspeaker cabinet loses high-frequency output, immediately remove power from the unit and wait for two to three minutes. This should be long enough to allow the poly switch to reset. Reapply power and check the performance of the high frequency driver before continuing, with the power reduced to a level that does not cause the poly switch to interrupt the signal.
Interference From Cell Phone
Using a cell phone near the speaker system can induce noise. If this occurs, move the cell phone further away from the speaker system. Air blowing out of the bass reflex ports is normal, and often occurs when the speaker is handing program material with heavy bass content.
The manufacturer will not be responsible for damage caused by improper use or modification to the device.
Always turn the power off when the device is not in use.
The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualified service personnel about replacing defective parts.
2
Loading...