Polaroid I-ZONE POCKET STICKER FILM User Manual
Film Data Sheet
i-Zone Pocket Sticker Film
Integral Color Print Film
Pocket Film
Description
General purpose High-speed, medium-contrast, integral film for
instant color prints. The film is balanced for daylight and
electronic flash exposure. On the back side of each photo there
is an adhesive that allows the user to place the photo on a variety
of surfaces such as book covers, lockers, walls, refrigerators, etc.
Sticker Film
Film Speed
ISO 640/DIN 29
Format
5
6
/8 x 13/8 in. (16.8 x 3.5 cm)
Image Area
3
1
/8 x 7/8
Finish
Glossy
Exposures per Unit
12 exposures per pack
Development Time
3 minutes approximately
in. (3.6 x 2.4 cm)
Key Applications
• Amateur photography
• Promotional photography
film
• Photographic souvenirs
• Party/special event photography
Compatible Hardware
• i-Zone Pocket Camera
• ID 1-2-3
• Barbie Pocket Camera
• Bugs Bunny and Tweety Bird Pocket Camera
• Tomy Xiao/Pocket Camera
Special T reatment
None
Alternative product
Pocket Film
Caution
This film uses a small amount of caustic paste. If any paste appears, avoid contact with skin, eyes and mouth
and keep away from children and animals. If you get some paste on your skin, wipe it off immediately, then
wash with water to avoid an alkali burn. If eye contact occurs, quickly wash the area with plenty of water and
see a doctor. Do not cut or take apart pictures or battery. Do not burn battery or allow metal to touch terminals.
Limited Warranty
See information on the film box.
“Polaroid” and “Polaroid I-Zone (and design)” are trademarks of Polaroid Corporation, Waltham,
451 USA. “Barbie” is a trademark owned and used under license from Mattel, Inc. Copyright 1999
MA 02
Mattel, Inc. All rights reserved. “Looney Tunes”, “characters”, “names” and “all related indicia” are
trademarks of Warner Bros. Copyright 1999.
Film Data Sheet
Technical Data
Pocket Film
The information in this data sheet
represents the typical performance
of Polaroid’s Pocket film. However,
there may be some variation
between film lots.
Recommended speed:
ISO/DIN 640/29
0
Characteristic H&D curve for
normal development
3
H&D Curves
o
F/21oC
@ 70
Blue
Green
Red
Recommended processing
time and temperature:
Approximately 3 minutes
at 700F/210C
Balance:
Daylight and electronic
flash (5500oK)
Contrast:
Medium
Resolution (1000:1):
7-10 line pairs/mm
D-Max: The density value for the
film’s darkest black.
D-Min: The lowest density value
that a film exhibits. In prints, the
whiteness of the brightest highlight,
relative to the unprocessed print.
Slope: The positive ratio of the log
E increments of the straight line
region of the curve, as determined
by the 1/4-3/4 increment method.
The slope of an H&D curve
indicates the overall contrast of a
film: low contrast slopes less than
1.10; medium contrast slopes from
1.10 to 1.70; high contrast slopes
greater than 1.70.
2
Sample Density
1
0
-3
Characteristic H&D curve for
cold development
3
H&D Curves
o
F/18oC
@ 55
2
Sample Density
1
0
-3
Relative Log Exposure
Relative Log Exposure
Blue
Green
Red
0-2 -1
Characteristic H&D curve for
hot development
3
H&D Curves
o
F/35oC
@ 95
2
Sample Density
1
0
-3
Relative Log Exposure
Blue
Green
Red
0-2 -1
0-2 -1
Loading...