Planet Eclipse SL94 User Manual
F E A T U R E
S U P P L E M E N T
FOR SL94 EGO
V1
READ AND ADHERE STICTLY TO ALL OF THE
SAFETY INSTRUCTIONS AND GUIDELINES IN
THE EGO9 OPERATORS MANUAL!
04 SL SHAFT3 BARREL KIT
05 SL94 FIXED OUTPUT LPR
CONGRATULATIONS,
Thank you for purchasing an SL-94 Ego marker. The SL range represents
the very best of Eclipse in terms of cutting edge
performance and
technology that deliver on our philosophy of refined design and super
fast markers that produce
I know you’ll be
you use your Marker please read through this
as well as the Ego9 Operation Manual in its entirety and pay particular
attention to all of the Warnings and Safety Guidelines. If you are missing
either the Feature Supplement or the Ego9 Operational Manual both can
be downloaded from the Downloads page at :
devastating firepower!
blown away with your new Eclipse SL-94, but before
Feature Supplement
www.planeteclipse.com
At the back of this supplement is a section that will allow you to record and
track your
Markers Service History.
05 ZICK 2 RAMMER SYSTEM
06 ADDITIONAL TRIGGER SYSTEMS
07 FSD DELAY PARAMETER
07 CURE 3 BOLT SYSTEM
08 SERVICE HISTORY
If you have any
Section in the
will find a list of accredited Dealer Service
Centres that will be able to help you out
or of course you can always contact
Nicky T in our Tech Support
Department directly
nick.t@planeteclipse.com
questions or problems turn to the Dealers & Service
Operation Manual where you
on:
JACK WOOD - CHIEF ENGINEER
SL SHAFT3 BARREL KIT
SL94 FIXED OUTPUT LPR
NOTE: THE BORE SIZE OF YOUR SHAFT 3 MAY VARY ACCORDING TO THE
Your Eclipse SL comes as standard with an Eclipse SL Shaft 3 barrel.
The barrel screws into the body of the SL using a right hand thread meaning
that if you hold the SL pointing away from you the barrel screws into the
body in a counter-clockwise direction.
The barrel comprises of two parts, a barrel back A and a barrel front B .
The two parts are joined together with a left hand thread meaning that
if you hold the barrel, with the back nearest you, the front unscrews in a
counter-clockwise direction. The bore size of the barrel back is engraved at
the end of the barrel back C .
C
FEATURE SUPPLEMENT
MODEL OF SL YOU HAVE.
D
4
#010 NBR 70
On the barrel back there is a 016 NBR 70 o-ring D which prevents the barrel
from vibrating loose from the SL body when the marker is fired. There is also
a 015 NBR 70 o-ring on the barrel front E helps with alignment when the
two sections are screwed together.
Replace and lubricate these o-rings with Eclipse Grease as necessary.
E
B
A
NOTE: THE SL WILL ONLY ACCEPT COCKER THREADED
BARRELS. DO NOT USE ANY OTHER TYPE OF BARREL
THREAD.
#14x2 NBR 70
OR #016 NBR 70
ZICK 2 RAMMER SYSTEM
ZICK 2 RAMMER
LPR PISTON
SPRING
LPR PISTON
#009 NBR 70
#013 NBR
#011 NBR 70
#009 NBR 70
70
LPR CAP
NOTE: WHEN INSTALLING THE FIXED OUTPUT LPR CAP, DO NOT
USE THE SMALL LPR ADJUSTER SPRING IN THE FRONT OF THE
PISTON FROM THE ADJUSTABLE LPR CAP. INSTALLING THE SMALL
LPR SPRING INTO THE FRONT OF THE FIXED LPR CAP WILL CAUSE
THE OUTPUT PRESSURE TO DROP TOO LOW AND CAUSE LOW AND
#010 NBR 70
CUSHION
BUMPER
INCONSISTENT VELOCITIES.
ZICK 2
CAP
#011 NBR 70
FEATURE SUPPLEMENT
5
Loading...