PLANET WNAP-6315 User Manual

2. Installation Precautions

Quick Installation Guide

WNAP-6315

150Mbps 802.11n Wireless Outdoor CPE

1. Package Contents

Thank you for choosing PLANET WNAP-6315. Before installing the
AP, please verify the contents inside the package box.

WNAP-6315

PoE Injector

Quick Guide

Plastic Strap x 1

Power Adapter

IMPORTANT SAFETY PRECAUTIONS:

1. LIVES MAY BE AT RISK! Please be aware of the
electrical wires around, and tighten the pole.
Carefully read the section "OUTDOOR
INSTALLATION WARNING" in the manual
before installation.

2. Users MUST use the “PoE Injector” and
“Power Adapter” shipped in the box with the

Caution

WNAP-6315. Otherwise, the product might be
damaged.

3. Users MUST use a proper and well-installed
surge arrestor and grounding wired with the
WNAP-6315; otherwise, a sudden lightning could
cause fatal damage to the WNAP-6315. EMD

(Lightning) DAMAGE IS NOT COVERED
UNDER WARRANTY.

3. Physical Introduction

Rear Panel Description – LED Indication

Power LED LAN 2 LED

If there is any item missing or damaged, please

Note

Bottom Panel Description – Port

contact the seller immediately.

– 1 – – 2 –

Optional RP-SMA Connector

LAN2

PoE LAN

LAN 1 LEDWireless LED

Step 2: Plug the RJ45 Ethernet cable into the PoE LAN Port of

the WNAP-6315. Then, slide back the cover of the
WNAP-6315 to finish the installation.

3 4

Step 3: Plug the power cord into the DC port and plug the

other end of the RJ45 cable into the POE port of the
PoE injector (See Step 2).

4. Hardware Installation

Step 1: Push the latch on the bottom of the WNAP-6315 and

slide down the cover to remove.

1 2

– 3 – – 4 –

To LAN Switch or PC

To WNAP-6315

Step 4: Successful installation.

5. Pole Mounting

Step 1: Place the strap through the slot on the back of the

WNAP-6315 and then around the pole. Tighten the
strap to secure the WNAP-6315.

6. Web Login

Connect the WNAP-6315 with your PC via an Ethernet cable
plugging into LAN port of PoE injector on one end and into LAN
port of PC on the other end. Power on the WNAP-6315 via PoE
from PoE injector.

1. Click the “Start” button located in the lower-left corner of
your computer.

2. Click “Control Panel”.

3. Double-click “Network and Sharing Center” icon.

4. Click “Change Adapter Settings”.

5. Double-click “Local Area Connection”.

6. Select “Internet Protocol Version 4 (TCP/IPv4)” and
click “Properties”.

7. Select “Use the following IP address”, and then click
the “OK” button twice to save the configuration. For
example, as the default IP address of the WNAP-6315 is

192.168.1.253 and the router is 192.168.1.254, then you
may choose from 192.168.1.1 to 192.168.1.252.

– 5 – – 6 –

Default IP Address: 192.168.1.253
Default User Name: admin
Default Password: admin
Default SSID: WNAP-6315

Step 1: The Web management allows you to access and

manage the wireless AP easily. Launch the Web
browser and enter the default IP address

http://192.168.1.253.

Step 2: When the login window pops up, please enter the

User Name and Password. The default User Name
and Password are both “admin”. Then click the OK
button to continue.

Step 3: After you enter into the Web User Interface, click

Smart Setup Wizard at the left hand side of the

screen. Once the basic configuration of the AP is
done. Click the Finish or Apply button to make the
change take effect.

Further Information:

The above steps introduce the simple installations
and configurations of the WNAP-6315. For further
configurations, please refer to the user manual
which you can download from the website.

http://www.planet.com.tw/en/support/download.p
hp?type1=4&model=48686&type=3

If you have further questions, please contact the local dealer or
distributor where you purchased this product.

For security reasons, it is recommended to change the
password at the first login and memorize it.

– 7 – – 8 –

2011-E10620-000