Pioneer VSXD-709 Owners manual

AUDIO/VIDEO

MULTI-CHANNEL RECEIVER

VSX-D709S

Operating Instructions

Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference.

WARNING: TO PREVENT FIRE OR SHOCK

HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

THE STANDBY/ON BUTTON IS

[For U.S. model] IMPORTANT NOTICE

The serial number for this equipment is located on the rear panel. Please write this serial number on your enclosed warranty card and keep it in a secure area. This is for your security.

SECONDARY CONNECTED AND THEREFORE DOES NOT SEPARATE THE UNIT FROM MAINS POWER IN STANDBY POSITION.

IMPORTANT

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Information to User

Alteration or modifications carried out without appropriate authorization may invalidate the user's right to operate the equipment.

[For Canadian model]

This Class B digital apparatus complies with Canadian ICES-003.

[Pour le modèle Canadien]

ATTENTION: AFIN DE PREVENIR TOUS

RISQUES DE CHOC ELECTRIQUE OU DE DEBUT D'ENCENDIE, NE PAS EXPOSER CET APPAREIL A L'HUMIDITE OU A LA PLUIE.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

LE BOUTON STANDBY/ON EST RACCORDE SECONDAIREMENT ET PAR CONSEQUENT

[For Canadian model] CAUTION: TO PREVENT ELECTRIC SHOCK, DO

NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

NE SEPARE PAS L’APPAREIL DE L’ALIMENTATION SECTEUR SUR LA POSITION D’ATTENTE.

ATTENTION: POUR PREVENIR LES CHOCS

ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR, UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSERESS A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.

IMPORTANT SAFETY INSTRUCTIONS

READ INSTRUCTIONS — All the safety

and operating instructions should be read before the product is operated.

RETAIN INSTRUCTIONS — The safety and

operating instructions should be retained for future reference.

HEED WARNINGS — All warnings on the

product and in the operating instructions should be adhered to.

FOLLOW INSTRUCTIONS — All operating

and use instructions should be followed.

CLEANING — Unplug this product from the

wall outlet before cleaning. The product should be cleaned only with a polishing cloth or a soft dry cloth. Never clean with furniture wax, benzine, insecticides or other volatile liquids since they may corrode the cabinet.

ATTACHMENTS — Do not use attachments

not recommended by the product manufacturer as they may cause hazards.

WATER AND MOISTURE — Do not use

this product near water — for example, near a bathtub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

ACCESSORIES — Do not place this product

on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

CART — A product and cart combination

should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

VENTILATION — Slots and openings in the

cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

POWER SOURCES — This product should

be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company.

LOCATION – The appliance should be in-

stalled in a stable location.

NONUSE PERIODS – The power cord of

the appliance should be unplugged from the outlet when left un-used for a long period of time.

GROUNDING OR POLARIZATION

÷ If this product is equipped with a

polarized alternating current line plug (a plug having one blade wider than the other), it will fit into the outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

÷ If this product is equipped with a three-

wire grounding type plug, a plug having a third (grounding) pin, it will only fit into a grounding type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding type plug.

POWER-CORD PROTECTION — Power-

supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

OUTDOOR ANTENNA GROUNDING — If

an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure A.

LIGHTNING — For added protection for this

product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

POWER LINES — An outside antenna

system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

OVERLOADING — Do not overload wall

outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

GROUND CLAMP

ELECTRIC SERVICE EQUIPMENT

Fig. A

OBJECT AND LIQUID ENTRY — Never

push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

SERVICING — Do not attempt to service

this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

DAMAGE REQUIRING SERVICE — Unplug

this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

÷ When the power-supply cord or plug is

damaged.

÷ If liquid has been spilled, or objects

have fallen into the product.

÷ If the product has been exposed to rain

or water.

÷ If the product does not operate normally

by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.

÷ If the product has been dropped or

damaged in any way.

÷ When the product exhibits a distinct

change in performance — this indicates a need for service.

REPLACEMENT PARTS — When

replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

SAFETY CHECK — Upon completion of any

service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

WALL OR CEILING MOUNTING — The

product should not be mounted to a wall or ceiling.

HEAT — The product should be situated

away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

NEC — NATIONAL ELECTRICAL CODE

Quick Start Guide

This is a quick guide to setting up your new receiver so you can get home theater surround sound. For more details on any of the information presented here check the main section of the manual.

Before making or changing the connections, switch off the power and disconnect the power cord from the AC wall outlet.

1 Hooking Up Your DVD Player & TV

In order to use Dolby Digital/DTS soundtracks which are at the heart of home theater you need to hook up your DVD player with digital audio connections. You can do this by either a coaxial or an optical connection, you don’t need to do both. The quality of these two types of connections is the same but since some digital components only have one type of digital terminal you need to figure out which yours has and hook it up to the appropriate terminal on the receiver. In order to do this you will need the proper cable. For coaxial connections you can use a regular RCA stereo cords or the specially-made coaxial cords, they have the same type of plugs. For optical connections you will need a special optical cord which you can buy at your local stereo store. Also hook up the video connection of your DVD player, the analog audio (for recording the audio on DVDs, use regular RCA stereo cords), and your TV (it's easiest to use a regular composite RCA video cords) as shown below. We also recommend hooking up your all your digital components to analog audio jacks. For this you can use regular RCA stereo cords.

Coaxial Digital Connection

If your DVD player has a coaxial terminal (not a PCM-only output) for the audio out hook it up using this terminal. Follow the diagram below. This is the best scenario, as you will be able to follow the default settings of this receiver and won't need to assign the digital inputs.

VIDEO INPUT

RCA video cord

VIDEO

RCA video cord

RCA stereo cord

coaxial cord

OUT

ANALOG

STEREO

DIGITAL

OUTPUT

DVD player

(not a PCM-only output)

Quick Start Guide

Optical Digital Connection

If your DVD player has an optical terminal (not a PCM-only output) for the audio out you can hook it up using this following the diagram below. You will need to assign the digital input (tell the receiver which input you put your DVD digital audio into). See the page 6 for this.

VIDEO INPUT

RCA video cord

VIDEO

RCA video cord

RCA stereo cord

optical cord

OUT

ANALOG

STEREO

DIGITAL

OUTPUT

DVD player

(not a PCM-only output)

2 Speaker Connections

Home theater is designed to be setup with five speakers (front left & right; center; surround left & right) and a subwoofer but you can use this receiver with fewer speakers. Hook up the speakers you have to the speaker A terminals on the back of the receiver. If you only have two speakers hook them up as "FRONT." If you have three hook up the single speaker as "CENTER." Follow the diagram on p.19 in order to hook up all your speakers. A center speaker is very important for watching films because the dialog comes from the center speaker in digital soundtracks. If you do not have a CENTER speaker you must tell the receiver the CENTER channel is OFF or when you listen to digital soundtracks you won't hear any dialog. Use the instructions on page 31-32 in order to do this.

Make sure you connect the speaker on the right to the right terminal and the speaker on the left to the left terminal. Also make sure the positive and negative (+/–) terminals on the amplifier match those on the speakers.

Powered

Front

speaker (A)

(Left)

subwoofer

TV/monitor

Front

speaker (A)

(Right)

Center

speaker

INPUT

Surround

speaker

(Left)

Surround

speaker

(Right)

Quick Start Guide

3 Setting up the Remote Control & Unit

1 Put the batteries in the Remote Control.

2 Plug the main unit into a AC wall outlet.

3 Press the

4 Digital Input Assignment

STANDBY/ON button on the receiver to put the receiver in ON mode.

This is only necessary if you hooked up your DVD to DIGITAL IN 3, as in the first diagram on p. 5 (an optical digital connection).

4 "Digital in" should be selected (if it

SOURCE

2 1

3-9

RECEIVER

VCR

MULTI CONTROL

VIDEO SELECT

RECEIVER

TV CONTROL

TVFUNK

CHANNEL

TUNE

ENTER

TUNE

MULTI CH INPUT

MASTER VOLUME

ENTER

CLASS

VCR 2

DISC

*‹&

DVD

CD CD-R TUN TVC

123

LOUDNESS

456

INPUT ATT DIGITAL NR FL DIMMER

789

REMOTE SETUP SYSTEM SETUP SIGNAL SELECT

+10

EFFECT/CH SEL

TV VOL

4¢

ST ST

GUIDE MENU

D.ACCESS BAND

isn't use the 5¥∞ buttons to select it). Press ENTER.

You should see the following display on your receiver.

5 Choose the "Digital-3" with 5¥∞

buttons you hooked up your DVD player to. Press ENTER.

6 Choose the "DVD/LD" (if it isn't use

1 Press the RECEIVER.

This switches the remote to the surround setup mode.

the 5¥∞ buttons to select it). Press ENTER.

2 Press the SYSTEM SETUP button.

You should see the following display on your receiver.

7 Select "Dig-In End" with 5¥∞

buttons and press ENTER to return to the Dig-In Setup menu.

• You can escape from this screen at any time by pressing the SYSTEM SETUP button again. None of the settings you made will be entered in this case.

• If don't enter any settings the receiver will revert back to its previous state after three minutes.

3 "Assign Set" should be selected (if it

isn't use the 5¥∞ buttons to select it). Press ENTER.

You should see the following display on your receiver.

8 Select "Assign End" with 5¥∞

buttons and press ENTER to return to the Assign Setup menu.

9 Select "Setup End" with 5¥∞

buttons and press ENTER to return to the System Setup menu.

Quick Start Guide

5 Playing a DVD with Surround Sound

1 Turn on your TV, and your DVD player.

2 Press the DVD button on the remote control.

You should see "DVD/LD" in the display on the receiver.

3 Press the STANDARD button for the basic surround sound setting.

4 Play a DVD.

6 For Better Surround Sound

1 Go through the entire "Initial Set Up" procedures as outlined on pages 27-38

of this instruction manual.

If you don't hook up any other components with digital audio or do so following the default settings of the receiver (see page 15) you won't have to assign any more digital inputs, but many other adjustments will improve the sound tremendously.

2 Experiment with the different sound settings offered with the 2/DTS and

DSP buttons.

For more information see pages 39-42.

3 As mentioned above you should go through the "Speaker Setting"

instructions on pages 31-32 to set up your speakers properly. If you don't do this you, at least, need to make sure the CENTER channel is turned off if you don't have a center speaker. Use the instructions on pages 31-32.

Features

Multi Channel Stereophonic Concept

The VSX-D709S receiver is constructed with Pioneer’s industry-leading multi channel stereophonic concept. This welldeveloped approach to receiver circuitry takes the high level base technology that, up until now, has been only used for stereo equipment and applies it to multi-channel audio-visual receivers. The result is that the product, in addition to being expertly built, and gives you optimal sound reproduction of DVDs, other multi channel sources and stereo sources as well. This receiver is designed capture to a true reproduction of the intentions of a filmmaker or music producer at the time they were mastering the soundtrack in the studio. It incorporates 5 independent high quality, high powered built in power amplifiers, with increased-performance direct energy MOS FET output circuits. This construction provides improved linearity and accurate representation of each channel for true high fidelity reproduction from even the most demanding Dolby Digital and DTS program sources. In addition, the amplifier uses Direct Construction to give the purest sound available. All these elements consolidated in one receiver afford the listener a new surround sound experience in his or her home.

Universal Player Compatibility

This receiver incorporates the latest technology and is able to handle cutting edge audio formats, like DVD Audio, which are just hitting the market. Its high compatibility offers a variety of inputs to decode all types of sources at the highest possible quality. The receiver’s multi channel in connections lets you hook up six discrete channels of audio. It also has multi channel direct inputs and the ability to decode the cutting edge formats.

Decoding of Digital Source Film Formats

Built into this receiver is the latest in film sound format technology. This receiver has the ability to decode Dolby Digital, Dolby Pro Logic and DTS (Digital Theater Systems) sources, which are the standards of home theater today.

Manufactured under license from Dolby Laboratories. “Dolby”,“AC-3”, “Pro Logic”, and double-D symbol are trademarks of Dolby Laboratories. Confidential unpublished works. © 1992 - 1997 Dolby Laboratories. All rights reserved.

“DTS” and “DTS Digital Surround” are trademarks of Digital Theater Systems, Inc. Manufactured under licence from Digital Theater Systems, Inc.

Advanced Theater Modes & DSP Surround Modes

Advanced Theater modes enhance the sound of either film or music so a more dramatic effect can be achieved. The four modes are each designed to accentuate specific sound qualities, giving the listener a wide range of possibilities. DSP (Digital Signal Processing) surround modes give you the capability of transforming your living room into seven different sonic environments when listening to music.

Midnight Mode, Digital Noise Reduction & 5 Channel Tone Control

The Midnight mode allows you to obtain excellent surround sound effects even when listening at low volumes, something that was previously impossible. Digital noise reduction filters out unwanted noise from recordings to give you a clearer sound and the 5 channel tone control allows you to adjust the treble and bass of each channel individually to suit your listening tastes.

Remote Control of Other Components

The supplied remote control can be used to operate a variety of other components simply by recalling the appropriate preset codes or by using the learning function to teach the remote control new commands.

The Energy-saving Design

This unit is designed to use less than 1 W of energy when the receiver is in standby mode.

Table of Contents

Quick Start Guide ................................ 4

Before You Start ................................. 10

Checking the Supplied Accessories ........................ 10

How to Use This Manual .......................................... 10

Preparing the Remote Control ................................. 10

Installing the Receiver .............................................. 11

Opening the Front Panel .......................................... 11

The PIONEER SR System: Operating other

PIONEER components .............................................. 11

Connecting Your Equipment ............. 12

Audio Components ................................................... 12

Digital Connections .................................................. 13

Example Connection for a DVD/LD or LD player .... 14

Video Components ................................................... 15

Satellite TV Components ......................................... 16

TV ............................................................................... 17

Multi Channel Input (External Decoder) ................. 17

Connecting the Radio Antennas .............................. 18

Speakers .................................................................... 19

Placing Your Speakers .............................................. 20

Connecting Additional Amplifiers ........................... 21

Plugging In ................................................................ 21

Displays & Controls ........................... 22

Front Panel ................................................................ 22

Remote Control ......................................................... 24

Display ....................................................................... 26

Initial Set Up ....................................... 27

Setting Up for Surround Sound .............................. 27

Basic Playback .................................... 39

Learning about the Sound Modes ........................... 39

Selecting a Sound Mode .......................................... 41

Playing Sources with

Dolby Digital or DTS Sound ..................................... 42

Playing Stereo Sources ............................................ 43

Switching Analog and Digital Signal Input ............ 44

Reducing Noise During Playback ............................ 45

Listening in Midnight Mode ..................................... 46

Listening the Loudness Mode ................................. 46

Adjusting Bass and Treble ....................................... 47

MULTI CHANNEL IN Playback ................................. 48

96kHz 24bit Performance ......................................... 48

Direct Playback .......................................................... 49

Adjusting the Brightness of the Display ................. 49

DUAL MONO Setting ................................................ 50

Using the Tuner .................................. 51

Automatic and Manual Tuning ................................ 51

Direct Access Tuning ................................................ 52

Memorizing Frequently Used Stations ................... 53

Recalling Memorized Stations ................................. 54

Remote Control of Other Components .. 55

Setting Up the Remote Control ............................... 55

Programming a Different Component

into a MULTI CONTROL button ................................ 58

Checking Preset Codes ............................................. 59

Clearing All the Remote Control Settings ............... 59

CD/CD-R/MD/VCR/LD Player Controls ..................... 60

Cassette Deck Controls ............................................. 61

DVD/DVR Player Controls ......................................... 62

DTV Controls ............................................................. 63

Cable TV/Satellite TV/TV Controls ........................... 64

Using Other Functions....................... 65

Function Rename ...................................................... 65

Recording from Audio Components ....................... 67

Recording from Digital Audio Components ........... 68

Recording from Video Components ....................... 68

Direct Function .......................................................... 69

Video Select .............................................................. 70

Changing the Display ............................................... 70

Techno Tidbits & Problem-solving ... 71

Dolby Digital .............................................................. 71

DTS ............................................................................ 71

Preset Code List ........................................................ 72

Troubleshooting ........................................................ 77

Specifications ............................................................ 80

PREPARATION

SET

OPERATION

Before You Start

Î

SOURCE

ENTER

LOUDNESS

INPUT ATT DIGITAL NR FL DIMMER

REMOTE SETUPSYSTEM SETUP SIGNAL SELECT

TV VOL

TVFUNK

ENTER

TUNE

D.ACCESS BAND

GUIDE MENU

CLASS

RETURN

MIDNIGHT DSP STEREO

FUNCTION

ADVANCEDSTANDARD MUTE

S.MODE CLEAR DTV INFO

AV PRE-PROGRAMMED AND LEARNING

REMOTE CONTROL UNIT

/ DSP

RECEIVER DIRECT CONTROL

MPX DTV ON / OFF DTV MENU

ST ST

CHANNEL

EFFECT/CH SEL

RECEIVER

TV CONTROL

MASTER VOLUME

DISC

+10

VIDEO SELECT

MULTI CONTROL

MULTI CH INPUT

DVD

CD CD-R TUN TVC

RECEIVER

123

456

789

!⁄

*‹&

VCR 1

VCR 2

4¢

¶

Checking the Supplied Accessories

Please check that you have received all of the following supplied accessories.

FM wire Antenna

AM loop Antenna

“AA” IEC LR6 batteries x 2

How to Use This Manual

This manual is for the VSX-D709S Audio/Video MultiChannel Receiver. This manual is divided into three main sections which will tell you how to setup and use the unit :

PREPARATION

First carry out the tasks below in this “Before You Start“ section to prepare the remote control, then connect the receiver to your other components as described in “Connecting Your Equipment“ (p.12). Take special care to connect your digital equipment like DVDs and LDs properly to be able to take advantage of the receiver’s surround sound systems (p.13-14). To learn about a specific button, control, or indicator, see “Displays & Controls“ starting on p.22.

SET UP

Performing the tasks in “Initial Set Up“ (from p.27) is essential to get proper surround sound.

Remote Control Unit

• Operating Instructions

OPERATION

To play some music or soundtrack refer to “Basic Playback“ on p.39. “Using the Tuner“ (p.51) explains how to use the radio of this unit. Doing the operations in “Remote Control of Other Components“ (p.55) is highly recommended so you can use this unit’s remote control for all your components. “Using Other Functions“ (p.65) explain the other possibilities of the receiver. “Techno Tidbits & Problem-solving“ (p.71) provide detailed technical information and a troubleshooting guide.

The following marks and symbols are used throughout the manual:

memo

Provides additional information, precautions, and advice.

Indicates a blinking button, indicator, or display.

Indicates a steadily lit button, indicator, or display.

Preparing the Remote Control

Loading the batteries

Load the batteries into the remote control as shown below. Please use alkaline batteries. When you notice a decrease in the operating range of the remote control, replace all batteries with new ones.

“AA” IEC LR6 batteries x 2

CAUTION!

Incorrect use of batteries may result in such hazards as leakage and bursting. Observe the following precautions.

• Never use new and old batteries together.

• Insert the plus and minus sides of the batteries properly according to the marks in the battery case.

• Batteries with the same shape may have different voltages. Do not use different batteries together.

• When disposing of used batteries, please comply with governmental regulations or environmental public institution’s rules that apply in your country or area.

Operating range of remote control unit

The area in which you can use the remote control to operate the VSX-D709S is fairly large. To use, point the remote control toward the remote sensor on the front panel of this unit while within the range shown right.

Remote control may not function properly if:

• There are obstacles between the remote control and the remote sensor.

• Direct sunlight or fluorescent light is shining onto the remote sensor.

• The receiver located near a device emitting infrared rays.

• Operated simultaneously with another remote control which uses infrared rays.

Installing the Receiver

Please note:

• Do not place objects directly on top of this unit. This would prevent proper heat dispersal.

• When installing in a rack, shelf, etc., be sure to leave more than 8 inches of space above the receiver.

DVD

SOURCE

RECEIVER

LOUDNESS

ULTI CONTRO

1 2 3

CD-R

INPUT ATT

VCR

4 5 6

REMOTE SETUP

+10

VIDEO SELECT

7 8 9

TUN

EFFECT/CH SEL

VCR 2

DIGITAL NR

SYSTEM SETUP

TVC

MULTI CH INPUT

TV VO

RECEIVER

FL DIMMER

4 ¢

SIGNAL SELECT

TV CONTROL

ENTER

TVFUNK

ST ST

DISC

MASTER VOLUM

CHANNEL

TUNE

D.ACCESS

ENTER

TUNE

GUIDE M PX

¶

RETURN

 ! ⁄

BAND

DTV ON / O

MIDNIGHTDSP STEREO

S.M

ENU

R ECEIV

ODE

CLASS

ER D

CLEAR

ADVANCED

DTV M

*‹&

ECT CO

ENU

DTV INFO

N TRO

STANDARDMUTE

AV PRE-PRO

FU N

/ DSP

C T IO

REMO

N GRAM TE CONTROL UNIT

M ED AND LEARNING



8 inches (20 cm )

Before You Start

PREPARATION

23 feet (7m)

Receiver

Opening the Front Panel

To open the front panel push gently on the lower third of the panel with your finger.

The PIONEER SR System: Operating other PIONEER components

Connecting an optional control cord allows you to operate other PIONEER components simply by pointing the receiver's remote control at the remote sensor on the front panel of the receiver. The receiver then sends the remote control signals to the other devices via the CONTROL OUT terminal.

CONTROL

OUT

Receiver

Remote Control

DVD

CD CD-R TUN TVC

LOUDNESS

INPUT ATT DIGITAL NR FL DIMMER

REMOTE SETUPSYSTEM SETUPSIGNAL SELECT

+10

EFFECT/CH SEL

TV VOL

4 ¢

ST ST

D.ACCESS BAND

MPX DTV ON / OFF DTV MENU

¶

RETURN

MIDNIGHTDSP STEREO

AV PRE-PROGRAMMED AND LEARNING

RECEIVER

SOURCE

VCR

MULTI CONTROL

1 2 3

VIDEO SELECT

MULTI CH INPUT

4 5 6 7 8 9

DISC

ENTER

RECEIVER

MASTER VOLUME

TV CONTROL

TVFUNK

CHANNEL

TUNE

ENTER

TUNE

GUIDE MENU

CLASS

*‹&

 ! ⁄

S.MODECLEAR DTV INFO

RECEIVER DIRECT CONTROL

FUNCTION

ADVANCEDSTANDARDMUTE

/ DSP

Î

REMOTE CONTROL UNIT

PIONEER

component bearing

the Î mark.

To CONTROL IN terminal of another PIONEER component bearing the Î mark.

memo

• You can also control PIONEER components (and those made by other manufacturers) by pointing the receiver's remote control directly at the respective component. This type of operation does not require control cords. All you have to do is recall the appropriate the stored settings (see p.55-56).

• If you use a remote control hooked up via the CONTROL IN jack with a control cord, you won't be able to use this unit's remote control.

Connecting Your Equipment

Audio Components

To begin set up connect your audio components to the jacks as shown below. These are all analog connections and your analog audio components (cassette deck) use these jacks. Remember that for components you want to record with you need to hook up four plugs (a set of stereo ins and a set of stereo outs), but for components that only play you only need to hook up one set of stereo plugs (two plugs). To use DTS or Dolby Digital surround sound features you must hook up your digital components to the digital inputs (see p. 13). We also recommend hooking up your digital components to analog audio jacks. If you want to record to/from digital components (like a CD-R) to/from analog components you must hook up your digital equipment with these analog connections. See p.13 & 14 for more on digital connections.

Before making or changing the connections, switch off the power and disconnect the power cord from the AC wall outlet.

*The arrows indicate the direction of the audio signal.

ANALOG

INPUT

OUTPUT

(REC)

(PLAY)

Recorder 1

(CD-R/TAPE1/MD etc)

Recorder 2

(CD-R/TAPE1/MD etc)

OUTPUT

(PLAY)

ANALOG

INPUT (REC)

7 Analog audio/video cords

Use audio/video cords (not supplied) to make analog audio and video connections.

Connect red plugs to R (right) and white plugs to L (left).

Be sure to insert completely.

7 Coaxial cords/Optical cables

Commercially available digital audio coaxial cords (standard video cords can also be used) or optical cables (not supplied) are used to connect digital components to this receiver.

When you use optical digital input or output terminals, pull off the caps and insert the plugs. Be sure to insert completely.

ANALOG

OUTPUT

CD player

Cassette deck placement

Depending on where the cassette deck is placed, noise may occur during playback of your cassette deck which is caused by leakage flux from the transformer in the receiver. If you experience noise, move the cassette deck farther away from the receiver.

Coaxial cord

(or standard video cord)

Optical cable

Connecting Your Equipment

Digital Connections

In order to use Dolby Digital/DTS soundtracks which are at the heart of home theater you need to make digital audio connections. You can do this by either a coaxial or an optical connection (you don’t need to do both). The quality of these two types of connections is the same but since some digital components only have one type of digital terminal, it is a matter of matching like with like (for example, the coaxial out from the component to the coaxial in on the receiver). The for a total of four digital inputs. For a DVD/LD player or LD player hook up see p.14. If possible hook up your digital equipment in accordance with this receiver's default settings, refer to the “Digital Input Assignment” below in order to do this. We also recommend hooking up your digital components to analog audio jacks as well in order to make recording from some digital sources which may be copy protected.

Connect your digital components as shown below.

There is one optical digital out jack (the CD recorder is connected to it in the diagram below). If you connect this to the optical input on a digital recorder (currently these include MD, DAT and CD-R) you can make direct digital recordings with this unit.

Before making or changing the connections, switch off the power and disconnect the power cord from the AC wall outlet.

*The arrows indicate the direction of the audio signal.

DIGITAL

OUTPUT

TV/Satellite tuner

VSX-D709S

has two coaxial and two optical inputs

PREPARATION

DIGITAL

OUTPUT

(PLAY)

INPUT (REC)

CD recorder

DIGITAL

OUTPUT

CD player

(not a PCM-only output)

DIGITAL

OUTPUT

DVD player

(for DVD/LD player hook up see p.14)

Digital Input Assignment

Unlike analog connections, the jacks for digital connections are not dedicated to one type of component, they can be used freely. Thus you must tell the receiver what digital component is in which jack so your components will be in sync with the names on the remote control buttons and the like. To avoid having to assign the digital inputs you can hook up your equipment in accordance with the receiver's default settings. The default settings are:

DIGITAL IN 1: DVD/LD DIGITAL IN 2: CD DIGITAL IN 3: CD-R/TAPE1/MD DIGITAL IN 4: TV/SAT

You will notice that Digital IN 1, for example, is a coaxial jack. If your DVD/LD player only has an optical out jack on it then you won't be able to hook up your components in accordance with the this case you will need to assign the digital inputs. See Digital Input Select on p.29 in order to do this.

VSX-D709S

default setting. In

Connecting Your Equipment

Example Connection for a DVD/LD or LD player

Make sure you connect your DVD/LD or LD players using both a digital connections.

To connect a DVD/LD player or LD player with it's 2 (AC-3) RF output, a commercially available

RF demodulator

and either a coaxial or optical

RF demodulator (RFD-1) is required. The RF demodulator changes the RF signal to a digital signal which is then processed by the

VSX-D709S

supplied with the RFD-1.

model through their digital input jacks. For more details, refer to the instruction manual

If your player has an 2 RF output this will ensure you can use all LDs. We also recommend hooking up your digital components to analog audio jacks. Before making or changing the connections, switch off the power and disconnect the power cord from the AC wall outlet.

*The arrows indicate the direction of the audio signal.

RF demodulator RFD-1

OPTICAL

DIGITAL IN

COAXIAL

RF OUT

(AC-3)(LD)

(not a PCM-only output)

DIGITAL OUT

PCM/

(OPT.)

DIGITAL OUT

(OPT.)

DIGITAL IN

PCM/

RF IN (AC-3)(LD)

DVD/LD player or LD player

VIDEO

ANALOG

STEREO

OUT

S-VIDEO

memo

Be sure to make either a digital coaxial or digital optical connection (pictured as DIGITAL jack 1 or DIGITAL jack 3 in this diagram) as well, but you don’t need to make both.

Also, be sure to assign the jacks to the proper component(s) with the Digital Input Select procedure (see p.29) if necessary. See the explanation on p.13 for details.

Make sure the RF demodulator digital in switch is set correctly (optical or coaxial depending on the connection).

Connecting Your Equipment

Video Components

Connect your video components to the jacks as shown below. Regarding a DVD there are two types of connections to make. Hook up your video signal with either S-video or composite video cords (the quality descends in this order) but remember, the video component you are watching and your TV must be hooked up with same type of video cord or you won't be able to see the picture. For the audio signal, order to use Dolby Digital/DTS you must hook up a digital input. It is also a good idea to hook up your DVD components with analog audio connections as well, since some DVDs may not have a digital audio track. To cover all possible Laser Discs a DVD/LD player or LD player requires an analog connection and two digital connections (a coaxial or optical and a specialized RF demodulator connection shown on the previous page). Before making or changing the connections, switch off the power and disconnect the power cord from the AC wall outlet.

*The arrows indicate the direction of the video signal.

Connecting DVD players

VIDEO

OUT

S-VIDEO

DVD/LD player

DIGITAL

ANALOG

STEREO

PCM/

/ DTS

DIGITAL

(not a PCM-only output)

PREPARATION

Connecting VCRs or DVRs

Portable DVD player (etc.)

COLOR BRIGHT MONITOR

PHONES

HOLDON/OFF

DIGITAL OUT (OPTICAL)

Front panel video connections are accessed via the MULTI JOG dial as "VIDEO."

AV-IN/OUT

S VIDEO OUT

OUT IN

AUDIO

(REC)

(PLAY)

VIDEOVIDEO

VCR 1/DVR

VCR 2

memo

S-VIDEO

OUT IN

AUDIO

(REC)

(PLAY)

VIDEO

S-VIDEO

If your video components have S-video jacks, you

could use S-video cords (not supplied) to connect them on the back of the receiver. These jacks are labeled by the Japanese designation "S2" on the VSX-D709S

but they are simply S-video jacks.

rear panel of the

However, if you use S-video cords for your video hook ups you must also hook up your TV with S-video connections. Conversely, if you use regular composite video cords for video hook ups, you should use them for your TV as well.

Connecting Your Equipment

TV/Satellite Tuner

Connect your satellite TV components to the jacks as shown below. Hook up the video signal with either S-video or composite video cords (the quality descends in this order) but remember, the video component you are watching and your TV must be hooked up with same type of video cord or you won't be able to see the picture. For the audio signal, order to use digital soundtracks (sometimes broadcast over digital satellite TV) you must hook up a digital input. Use either a coaxial or optical cables, it doesn't matter which (you don't need to use both). It's also a good idea to hook up your audio with analog cables (see below). This connection is called STEREO AUDIO OUT in the diagram. Before making or changing the connections, switch off the power and disconnect the power cord from the AC wall outlet.

*The arrows indicate the direction of the TV signal.

VIDEO

OUT

S-VIDEO

TV/Satellite tuner

ANALOG

STEREO

DIGITAL

Connecting Your Equipment

Connect your TV to the jacks as shown below. Hook up the signal with either S-video, or composite video cords (the quality descends in this order) but remember, the video component you are watching and your TV must be hooked up with same type of video cord or you won't be able to see the picture. Before making or changing the connections, switch off the power and disconnect the power cord from the AC wall outlet.

TV/monitor

VIDEO IN

VIDEO

S-VIDEO

PREPARATION

Multi Channel Input (External Decoder)

In some cases you may want to have your source material (DVD, etc.) decoded externally. If you find you need a multi channel external decoder hook one up as shown below, but for most people this component is unnecessary (For more on this see p.48).

Before making or changing the connections, switch off the power and disconnect the power cord from the AC wall outlet.

Components equipped with

5.1 channel analog output jack

SUB

WOOFER

ANALOG

CENTER

SURROUND

FRONT

Connecting Your Equipment

Connecting the Radio Antennas

Connect the supplied FM wire antenna and the AM loop antenna to the antenna terminals as shown below. These antennas should provide adequate reception quality in most cases, but connecting outdoor antennas should noticeably improve sound quality. Before making or changing the connections, switch off the power and disconnect the power cord from the AC wall outlet.

FM wire antenna

AM loop antenna

7 AM loop antenna

1 Assemble the antenna.

2 Twist exposed wire strands

together and insert.

3/8 in. (10 mm)

3 Attach to a wall, etc. (if

desired) and face toward the direction providing the best reception.

Using external antennas

7 To improve FM reception

Connect an external FM antenna.

7 To improve AM reception

Connect a 15-18 feet (5-6 meter) length of vinyl-coated wire to the AM antenna terminal in addition to the supplied AM loop antenna.

For best possible reception, suspend horizontally outdoors.

Outdoor antenna

AM loop antenna

15–18 ft. (5–6 m)

Indoor antanna (vinyl-coated wire)

Connecting Your Equipment

Speakers

A full complement of six speakers is shown here but, naturally, everyone's home set up will vary. Simply connect the speakers you have in the manner described below. The receiver will work with just two stereo speakers (called "front" speakers in the diagram) but the receiver is designed to be used with at least three speakers.

In general, make sure you connect the speaker on the right to the right terminal and the speaker on the left to the left terminal. Also make sure the positive and negative (+/–) terminals on the receiver match those on the speakers. Before making or changing the connections, switch off the power and disconnect the power cord from the AC wall outlet.

PREPARATION

memo

speaker (A)

Surround

speaker

(Left)

The receiver has two speaker systems, A & B. A is the main system supporting the full complement of surround sound speakers. If you switch on both A & B speaker systems, only front speakers and the subwoofer will be audible. No sound will come from the center or surround speakers but multi channel sources will be down-mixed to the active speakers so no sound will be lost. Similarly, if you choose just the B system you‘ll only hear the front speakers connected to the B system and multi channel sources will be down-mixed to these two speakers.

For the VSX-D709S you can use speakers with a nominal impedance rated 6Ω-16Ω, see the

following page.

Powered

Front

(Left)

subwoofer

INPUT

TV/monitor

Center

speaker

Front

speaker (A)

(Right)

Surround

speaker

(Right)

7 Speaker terminals

1 Twist exposed wire

strands together.

3/8 in. (10mm)

2 Loosen speaker terminal

and insert exposed wire.

3 Tighten

terminal.

The speaker terminals also accept single banana plugs. (Refer to speaker manual for details.)

Connecting Your Equipment

Speaker impedance

You can change the speaker impedance for

of 8Ω-16Ω (the default setting). If you are using 6Ω- less than 8Ω impedance speakers, you need to change the impedance setting. Use any speaker rated between 6Ω-16Ω.

STANDBY/ON

SPEAKERS

VSX-D709S

but we recommend using speakers with an impedance

First turn the receiver off, then press the power button while holding down the SPEAKERS button.

The receiver will reset to the new impedance setting. To choose

a new impedance setting repeat the process above. You can

choose the 8Ω-16Ω setting or the 6Ω-8Ω setting.

(This display indicates a 6Ωless than 8Ω impedance

setting.)

memo

To check which impedance setting to hold down the SPEAKERS button for 2-3 seconds. You'll get a display like

(This display indicates an 8Ω16Ω impedance setting.)

these telling you the speaker impedance setting.

Placing Your Speakers

Proper speaker placement is essential to realize the best sound from your system. The diagram and tips given here are just a rough guide; be sure to read the instructions that come with your speakers.

Speaker placement

If you have a multiple speaker arrangement the placement of the speakers is extremely important. To achieve the best possible surround sound, install your speakers as shown below. Make sure all speakers are installed securely to prevent accidents and improve sound quality. Be sure to consult your speaker manuals for the best placement of the speakers. Some speakers are designed to be floor-standing but others benefit greatly from speakers stands which raise them off the floor.

Front

Left

Surround

Left

Listening

Position

Front RightCenter

Sub

Woofer

Surround

Right

memo

• Install the left and right front speakers at equal distances from the TV.

•

When installing speakers near the TV, we recommend using magnetically shielded speakers to prevent possible interference such as distortion in the color of the TV screen. If you do not have magnetically shielded speakers and notice discoloration of the TV screen, place the speakers farther away from the TV.

• Install the center speaker above or below the TV so that the sound of the center channel is localized at the TV screen.

CAUTION:

When installing the center speaker on top of the TV, be sure to secure it with tape or some other suitable means. Otherwise, the speaker may fall from the TV due to external shocks such as earthquakes, and it may lead to endangering those nearby or damaging the speaker.

• If possible, install the surround speakers slightly above ear level.

• It may be difficult to obtain a cohesive surround effect if the surround speakers are installed farther away from the listening position than the front and center speakers.

Connecting Your Equipment

Connecting Additional Amplifiers

This receiver has more than sufficient power for any home use, but it is possible to add additional amplifiers to every channel of your system. Make the connections shown below to add amplifiers to power your speakers. Before making or changing the connections, switch off the power and disconnect the power cord from the AC wall outlet.

ANALOG

INPUT

ANALOG

INPUT

ANALOG

INPUT

Powered subwoofer

Front channel amplifier

Surround channel amplifier

Center channel amplifier (mono)

PREPARATION

Plugging In

Up to two components can be powered from this receiver. Two of the outlets are switched, which means that power is switched on and off with the receiver. Before making or changing the connections, switch off the power and disconnect the power cord from the AC wall outlet. After connecting all your components, plug the receiver's power cord into a standard wall power outlet.

Caution!

Power consumption of any equipment connected to the switched power outlets should not exceed 100W (0.8 A).

To avoid overheating, fire risk and possible malfunction, do not connect high-wattage appliances such as heaters, irons, monitors or TV sets to this units AC outlets.

Disconnect the receiver from the power outlet when it's not in regular use, for example, when on vacation.

Caution!

Do not connect a monitor or TV to this unit's AC OUTLETS.

Displays & Controls

Front Panel

All the controls on the front panel are explained and/or referenced here. To open the front panel push gently on the lower third of the panel.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

VSX-D709S

1617181920

1 STANDBY/ON button

Press to switch the receiver ON or into STANDBY mode.

STANDBY indicator

Lights when the receiver is in STANDBY mode. (Please note that this receiver consumes a small amount of power [1.0 W] in the standby mode.)

2 MIDNIGHT button (See p. 46)

Switches the MIDNIGHT mode on or off.

3 DIGITAL NR button (See p.45)

Switches the DIGITAL NR on or off .

4 MULTI CH INPUT (See p.48)

Use to hook up an external component that can decode other types of signals and input them into the VSX-D709S.

5 DSP MODE button (See p.40-41)

Press repeatedly to select a DSP sound mode. (HALL 1, HALL 2, JAZZ, DANCE, THEATER 1, or THEATER 2, 5 CH STEREO). Use these modes to produce surround sound from standard (two channel) stereo sources and create different listening environments.

STEREO/DIRECT button (See p.40,49)

Switches the receiver into STEREO mode if it was in a different sound mode (like ADVANCED THEATER) or toggles between DIRECT and STEREO mode. For more on STEREO mode see p.43

DIRECT playback bypasses the tone controls and channel level for the most accurate reproduction of a program source.

/ DTS buttons (See p.39 & 71)

ADVANCED – Use to select one of the four

Advanced Theater modes. Use to create certain types of sound environments when listening to Dolby Digital, Dolby Pro Logic or DTS sources.

STANDARD – Use for pure decoding of multi channel sources, especially Dolby Digital, Dolby Pro Logic or DTS sources.

SIGNAL SELECT button

Press SIGNAL SELECT repeatedly to select one of the following:

ANALOG – Analog signal.

DIGITAL – Digital signal (DVD/LD, TV/SAT, CD,

CD-R/TAPE 1/MD, VCR 1/DVR, VCR 2).

AUTO – This is the default. If there are both analog and digital signals the receiver automatically selects the best possible signal.

SPEAKERS (A/B) button

Use to select the speaker system. A is the primary setting. It plays all speakers hooked up to the A system. A & B setting only plays the front speakers of both the A & B systems and the subwoofer. Multi channel sources will be down-mixed to these speakers so no sound will be lost. B setting only plays the front speakers connected to the B system and multi channel sources will be down-mixed to these two speakers. The button cycles through the speaker systems as follows: A]B]A&B]off

Displays & Controls

7 FL DIMMER button

Use to adjust the brightness of the fluorescent display (FL = fluorescent display). Four levels of the brightness ranging from very dim to very bright can be selected. Each press changes the brightness of the display.

VIDEO SELECT button

Switches the receiver between the various types of video input (DVD, VCR 1, etc.) while keeping the audio on a fixed source (for example, the CD function).

TAPE 2 MONITOR button (See p.67)

Selects the tape deck (MD recorder, etc.) connected to the TAPE 2 MONITOR inputs/ outputs. Allows monitoring of a recording as it's being made. Be careful as this function will override other audio inputs if swtiched on.

TUNER CONTROL buttons (See p.51-54)

BAND – Press to select the AM or FM band.

CLASS – Press repeatedly to switch the preset

station classes.

TUNING SELECT – Switches the STATION/ TUNING button between station memory and frequency select modes.

STATION –/+ – Selects station memories when using the tuner.

TUNING –/+ – Selects the frequency when using the tuner.

MPX – Press to switch between auto stereo and MONO reception of FM broadcasts. When the broadcast signal is weak, selecting MONO will improve the sound quality.

MEMORY – Press to start the memorization of a preset station.

11 Display (See p. 26) 12 Remote sensor

Point the remote control toward the remote sensor to operate the receiver.

INPUT ATT button

Use to lower the input level of an analog signal that is too powerful, thus causing the sound to distort (the OVER indicator will light when this is the case).

14 MULTI-JOG CONTROL buttons

SETUP – Press to switch to the setup mode. RETURN – Press to move back one step in the

SETUP process.

15 MULTI JOG dial

You can use this dial for three purposes. Firstly, in normal mode turn it to select a source component. Secondly, you can press it to

display the sound mode. Lastly, when you press the SETUP button (14), you can use it to perform SETUP operations (turn to select, push to enter).

The source indicators in the upper right hand of the display window show the current source component even when the main display is showing the sound mode. They are as follows:

DVD/LD – DVD player or Laser Disc player.

TV/SAT– TV or satellite tuner.

CD – Compact Disc player.

CD-R/TAPE1/MD – CD recorder, Tape deck or

Mini Disc recorder connected to CD-R/TAPE1/ MD inputs/outputs.

TUNER – The built-in tuner.

VIDEO – Portable DVD player, game or video

camera (etc.) connected to the VIDEO INPUT on the front panel.

VCR1/DVR – Video cassette recorder connected to VCR1/DVR inputs.

VCR 2 – Video cassette recorder or other component connected to VCR 2 inputs.

MASTER VOLUME

Adjusts the overall receiver volume.

17 VIDEO INPUT jacks (See p.15)

S-VIDEO : Video input for connecting a

Portable DVD player or game (etc.), that has an S-Video out.

VIDEO / AUDIO (L/R) : Video input for connecting a Portable DVD player or game (etc.) that has standard video/audio outputs.

18 LOUDNESS button (See p.46)

Switches the LOUDNESS mode on or off.

19 TONE button

This button has two functions. Firstly, it switches between TONE ON and TONE BYPASS, which bypasses the tone circuitry. Secondly, you need to press the button before using the CHANNEL SELECT buttons to adjust the BASS & TREBLE.

CHANNEL SELECT button

Switches the tone adjust controls between the FRONT, CENTER, SURROUND speakers. You can then use the BASS and TREBLE controls to adjust the sound.

BASS (–/+) button (See p.47)

Use to adjust low frequencies.

TREBLE (–/+) button (See p.47)

Use to adjust the high frequencies.

20 PHONES jack

Connect headphones for private listening (no sound will be heard through the speakers).

PREPARATION

Displays & Controls

Remote Control

7 8

9 0

= ~

! @

1 SOURCE button

Use to turn on/off other components connected to the receiver.

2 MULTI CONTROL buttons

Use to put the receiver/remote control in the stated mode. For other equipment controls, see "Remote Control of Other Components" starting on 55.

3 NUMBER/MODE buttons

Use the NUMBER buttons to select the radio frequency in tuner DIRECT ACCESS mode or the tracks in CD, DVD mode etc.

Also, buttons marked with the following names have special functions. If you try to use one of these functions but the display flashes it means that function cannot be used in the current mode (for example DSP modes cannot be used when 5.1 CH setting is on).

SOURCE

DVD

CD CD-R TUN TVC

1 2 3

LOUDNESS

4 5 6

INPUT ATT DIGITAL NR FL DIMMER

7 8 9

REMOTE SETUP SYSTEM SETUP SIGNAL SELECT

+10

EFFECT/CH SEL

TV VOL

4 ¢

ST ST

GUIDE MENU

D.ACCESS BAND

MPX DTV ON / OFF DTV MENU

¶

 ! ⁄

RETURN

RECEIVER DIRECT CONTROL

MIDNIGHT DSP STERE O

ADVANCED STANDARD MUTE

AV PRE-PROGRAM MED AND LEARNING

REMOTE CONTROL UNIT

RECEIVER

VCR

MULTI CONTROL

VIDEO SELECT

MULTI CH INPUT

ENTER

RECEIVER

MASTER VOLUME

TV CONTROL

TVFUNK

CHANNEL

TUNE

ENTER

TUNE

CLASS

S.MODE CLEAR DTV INFO

RDM

FUNCTION

/ DTS

LOUDNESS button

Use to switch on the loudness. This feature is

$ %

VCR 2

useful for getting good bass and treble sounds listening at low volumes.

VIDEO SELECT button

Switches the receiver between the various types of video input.

MULTI CH INPUT button

Use to hook up an external component that can decode other types of signals and input them

DISC

^ &

into the VSX-D709S (see p.48).

INPUT ATT button

Use to lower the input level of an analog signal that is too powerful, thus causing the sound to distort (the OVER indicator will light when this is the case).

DIGITAL NR button

Press to switch Digital NR on or off (see p.45).

FL DIMMER button

*‹&

( )

_ + ¡

™

Î

£ ¢

REMOTE SETUP button

Use to customize the remote control functions and the remote control itself. (See “Remote Control of Other Components“ starting on p.55.)

SYSTEM SETUP button

Use to set up the speaker and sound systems. For more information see “Setting up for Surround Sound“ starting on p.27.

SIGNAL SELECT button

Press SIGNAL SELECT repeatedly to select one of the following:

ANALOG – Analog signal.

DIGITAL – Digital signal (DVD/LD, TV/SAT, CD,

CD-R/TAPE 1/MD, VCR 1/DVR, VCR 2).

AUTO – This is the default. If there are analog, or digital signals input the receiver automatically selects the best possible signal.

EFFECT / CH SEL button

For DSP/advanced theater sound modes use to put into the mode to add or subtract the amount of effect. For other sound modes use to select individual channels to increase or decrease channel level.

EFFECT +/– buttons

Use to add or subtract the amount of effect in different DSP/advanced listening sound modes or the level of individual channels.modes.

ENTER button (DISC)

Use to enter commands into TVs or DTVs. For CD players use to change discs.

Displays & Controls

4 THE FOLLOWING FOUR SETS OF

BUTTONS ARE DEDICATED TV CONTROL. THEY ARE ONLY USED FOR CONTROLLING YOUR TV.

TV VOL +/– buttons

Use to adjust the volume on your TV.

TV button

Use to turn on the power of the TV.

TV FUNC button

Use select the TV function.

5 4 ¢ /CHANNEL +/– buttons

Use to adjust channels on your TV and VCR or use to select tracks on your DVD or CD player.

6 5(+)/∞(–)/2/3/ENTER buttons

Use to set up surround sound, speakers levels & settings, and other set up features see p. 27-38). Specific use of these buttons is described in conjunction with the operations they perform. For more information see each individual section. Also, use these buttons to select radio frequencies.

7 GUIDE button

Use to control the guide for TV/Satellite TV.

8 3 button (BAND)

Use to play components or use to switch between the AM and FM band when in TUNER mode. You can also use to select the green channel on digital TVs (DTV).

9 7 button (D.ACCESS)

Use to stop other components. Also use to directly access a radio station by pressing the number of the station you want. You can also use to select the blue channel on digital TVs (DTV).

0 ¶ (MPX)

Use to record other components. Also use to switch between auto stereo and mono reception of FM broadcasts. If the signal is weak then switching to MONO will improve the sound quality. You can also use to select the yellow channel on digital TVs (DTV).

- RETURN button

Use to return to a previous setting during SETUP operations

= S.MODE button

Use to select the screen mode.

~ MIDNIGHT button (see page 46)

Use to put receiver in MIDNIGHT mode.

! DSP button (See p.40-41)

@ ADVANCED button

Use to select one of the four Advanced Theater modes. Use to create certain types of sound environments when listening to Dolby Digital, Dolby Pro Logic or DTS sources.

# STEREO button (See p. 40 & 49)

Switches the receiver into STEREO mode if it was in a different sound mode (like ADVANCED THEATER) or toggles between DIRECT and STEREO mode. For more on STEREO mode see p.40. DIRECT playback bypasses the tone controls and channel level for the most accurate reproduction of a program source.

$ LED DISPLAY

This display flashes when a command is sent from the remote control to the receiver. It also flashes at other times, for example when teaching the receiver preset codes, with specific meanings.

% RECEIVER button

This switches between STANDBY mode and power ON for this receiver.

^ RECEIVER button

Use to switch the remote to the receiver control mode.

& MASTER VOLUME +/– buttons

Use to set the overall listening volume.

* MENU button

Use to get the various menus for your TV or DTV.

( 8 button (CLASS)

Use to pause components or use the CLASS feature to switch between the three banks (classes) of station memories. You can also use to select the red channel on digital TVs (DTV).

) ¡ button (DTV MENU)

Use to fast forward search on CDs etc. Also you can access the DTV menu with this button.

_ 1 button (DTV ON/OFF)

Use to fast reverse search on CDs etc. Also use to turn DTV on/off.

+ RDM (DTV INFO)

Use to fast reverse search on CDs, etc. Also you can access the DTV information with this button.

¡ CLEAR button

This button clears the on-screen display (OSD) of a digital TV (DTV) menu.

™ FUNCTION button

Press to select a source. The button will cycle through all the possible sources.

£ MUTE button

Press to mute or restore the volume.

¢ STANDARD button

Use for pure decoding of multi channel sources, especially Dolby Digital, Dolby Pro Logic or DTS sources.

PREPARATION

Displays & Controls

Display

All the display information is explained and/or referenced here.

12 3 4 56 7 8

91011121314

1 Speaker indicators

Light to indicate the current speaker system, A and/or B.

2 SIGNAL SELECT indicators

Light to indicate the input signal you selected.

AUTO : Lights when the receiver is set to select the input signal automatically. ANALOG : Lights when analog signals are assigned. DIGITAL : Lights when digital audio signals are selected.

Program Format indicator

2DIGITAL : Lights when a source with Dolby Digital signals is played.

DTS : Lights when a source with DTS audio signals is played.

For Dolby Digital or DTS sources, these indicators change according to which channels are active in the source.

L – Left front channel. C – Center channel. R – Right front channel. LS – Left surround channel. S – Surround channel (mono). RS – Right surround channel. LFE – Low Frequency Effects channel.

4 2/dts mode indicators

2 DIGITAL – Indicates multi channel playback

of a Dolby Digital source.

2 PRO LOGIC – Lights when Dolby Pro Logic

decoding is switched on.

dts : When the 2/dts mode on the receiver is

on, this indicator lights to indicate playback of a DTS signal.

5 DSP indicator (See p.40–41)

Light when a DSP or Advanced Theater mode is selected.

6 STEREO indicator

Lights when a STEREO mode is selected.

7 Source indicators

3 indicator lights the selected source.

TAPE 2 indicator

Lights when the TAPE 2 monitor is on.

MASTER VOLUME indicator

Displays current volume level.

Sound control indicators

DNR – Lights when the digital NR is on. LOUDNESS – Lights when the Loudness is on. TONE – Lights when the Tone control is on. MIDNIGHT – Lights when the Midnight mode

is on.

Tuner indicators

STEREO – Lights when a FM stereo broadcast

is received in the auto stereo mode.

TUNED – Lights when a broadcast is received. MONO – Lights when the tuner is set to

receive FM broadcasts with the mono mode selected.

H.P (headphones)

Lights when headphones are connected to the PHONES jack (speakers systems A and B both turn off automatically).

Character display

Shows current mode, status, etc.

Analog level indicators

OVER – When the source signal is analog, this

lights if the signal is in danger of distorting. Press INPUT ATT to lower the signal level.

ATT – Lights when ATT is used to reduce the level of the analog source signal.

+ 58 hidden pages