Pioneer V2500NE, RM-V2400NE, RM-V2400, V2500NA, RMF-V4011 User Manual

...

TECHNICAL MANUAL (Ver.1.0)

MULTI PROJECTION UNIT

RM-V2400NA / V2500NA RM-V2400NE / V2500NE

PROJECTION SCREEN KIT

RMS-V4011/ V5011

PROJECTION FRAME

RMF-V4011/ V5011

PROJECTION CABINET

RMF-V4011R / V4011CR

Caution

This symbol refers to a hazard or unsafe practice which can result in personal injury or property damage.

Notes:

• Pioneer will not be liable for any loss caused by defects of the parts supplied other than by Pioneer.

• An damage during shipping will be compensated for only in the case where Pioneer's specific packing materials for shipping are used.

• The guarantee of performance is applicable only when the assembly and adjustment described in this technical manual and the adjustment described by the system manual of RM-V2000 have been carried out.

• Specifications and design subject to possible modification without notice, due to improvements.

PIONEER RM-V2400 / 2500

MANUAL.

This Acrobat (IE: a PDF file) version of the Pioneer RM-V2400 / 2500 manual was made from the original digital document and scanning an existing manual. Because of this, there are many less then perfect pages and hand written comments.

As Pioneer is constantly working towards providing the best possible documentation for our products, there may be an improved version of this document available. Please contact your Pioneer representative for additional information.

Josh Kairoff Pioneer New Media Technology. October 27, 1997.

CONTENTS

CHAPTER 1. FEATURES OF PROJECTION CUBE SYSTEM .............................................................. 4

1. FEATURES OF SYSTEM........................................................................................................................................... 4

2. FEATURES OF MULTI PROJECTION UNIT (RM-V2400N/V2500N) ....................................................................... 4

3. FEATURES OF FRAME TYPE ................................................................................................................................... 5

4. FEATURES OF CABINET TYPE ................................................................................................................................ 5

CHAPTER 2 . GENERAL SPECIFICATIONS ......................................................................................... 6

1. SPECIFICATIONS ...................................................................................................................................................... 6

(1) Multi Projection Unit (RM-V2400N/V2500N)................................................................................................... 6

(2) Projection Screen Kit(RMS-V4011/V5011)Product Weight:11.0kg/14.0kg .................................................. 13

(3) Projection Frame (RMF-V4011/V5011)Product Weight:26.8kg/28.8kg ........................................................ 14

(4) Projection Cabinet(RMF-V4011R/V4011CR) .................................................................................................. 15

(5) Projection Install Table (RM-V112/RMA-V5010) ........................................................................................... 17

(6) Munting Unit (RMA-V2050/2060)................................................................................................................... 18

(7) Multi Video Processor(RMD-V3216/3109,RMD-V2170) ................................................................................ 19

(8) Adjustment Control Unit (RU-V107)*Option ................................................................................................ 21

(9) Projection Cabinet (RMF-V4011R) Accessories ............................................................................................ 22

2. SYSTEM DIMENSIONS .......................................................................................................................................... 23

(1) 160-inch (40-inch 4×4screens)…For RMF-V4011 ......................................................................................... 23

(2) 200-inch (50-inch 4×4screens)…For RMF-V5011 ......................................................................................... 24

(3) 160-inch (40-inch 4×4 screens)…For RMF-V4011R...................................................................................... 25

CHAPTER 3. INSTALLATION AND ASSEMBLY ............................................................................... 26

1. INSTALLATION CONDITIONS ............................................................................................................................... 26

(1) Installing Ground ............................................................................................................................................ 26

(2) Ceiling .............................................................................................................................................................. 27

(3) Front Space ..................................................................................................................................................... 27

(4) Rear Space ...................................................................................................................................................... 27

(5) Number of Units Stacked Up ......................................................................................................................... 27

(6) Prevention of Tilting ....................................................................................................................................... 27

(7) Calculating the Heat Quantity ........................................................................................................................ 28

(8) Temperature and Humidity............................................................................................................................ 28

(9) Ventilation for system .................................................................................................................................... 29

(10) Condensation ................................................................................................................................................ 30

(11) Visible Angle ................................................................................................................................................. 31

(12) Lighting.......................................................................................................................................................... 34

(13) Effects of Earth Magnetism.......................................................................................................................... 34

(14) Connection with a Power Supply ................................................................................................................ 35

(15) Cables Used .................................................................................................................................................. 36

(16) Semi-outdoor Installation ............................................................................................................................ 36

(17) Precautions for Use of User-Obtained Parts .............................................................................................. 36

2. INSTALLATION AND ASSEMBLY ......................................................................................................................... 37

(1) Confirmation ................................................................................................................................................... 37

(2) Opening the Packaging .................................................................................................................................. 37

(3) Carrying the Units After Opening Packaging ............................................................................................... 43

3. PRECAUTIONS FOR TRANSPORTATION ............................................................................................................. 44

4. ASSEMBLING THE SYSTEM ................................................................................................................................. 45

(1) Assembling the Projection Frame (RMF-V4011/V5011) ............................................................................... 45

(2) Assembling the System ................................................................................................................................. 46

5. SPECIAL INSTALLATION ....................................................................................................................................... 60

(1) Wall inset ......................................................................................................................................................... 60

(2) Diagonal installation....................................................................................................................................... 60

(3) Architrave processing .................................................................................................................................... 60

(4) Upside down installation ............................................................................................................................... 60

(5) Hanging from ceiling...................................................................................................................................... 60

CHAPTER 4. ADJUSTMENTS ............................................................................................................ 61

1. ADJUSTMENT PREPARATIONS ........................................................................................................................... 61

(1) Wiring .............................................................................................................................................................. 61

(2) Wiring Handling .............................................................................................................................................. 61

(3) Aging ............................................................................................................................................................... 61

Dimensions

545

GENERAL SPECIFICATIONS

490

540

380

(Fig.2-1)

GENERAL SPECIFICATIONS

Power Supply Panel

No.

Main power switch

Name

AC inlet

AC outlet

RM-V2400NA/V2500NA

See-saw switch

Type

RM-V2400NE/V2500NE

(Fig. 2-2)

Connects AC power cord.

Connects other multi-projection units. Not linked to main power switch. Note 1)

Turns on and off the power supplied to the main unit. Sets into the standby state when turned on.

Function

Note 1) Refer to page 35 [(14) Connection with a power supply 3 Connection].

Fuse holder

Stores the fuse. No-one except serviceman should touch this part.

Control Panel

(Fig. 2-3)

GENERAL SPECIFICATIONS

No.

ABL link switch

Linked input terminal

Linked output terminal

Remote control connection terminal

RS-232C port

Control input terminal

Y (Luminance) input terminal

C (Color) input terminal

Video input terminal

Video output terminal

TERMINATE switch

COMBINATION switch

MULTI switch

COLOR MODE switch

INPUT switch

Name

Type

Slide switch

DIN 6PIN

Mini jack

D-sub 25 PIN (Female) BNC connector

BNC connector BNC connector BNC connector BNC connector Slide switch Tact switch Tact switch Tact switch Tact switch

Function

Used for switching the control level of the ABL link control voltage when ABL link is ON.

Input terminal of ABL signal, remote control signal and RS-232C signal

Output terminal of ABL signal, remote control signal, and RS-232C signal

Connected to adjusting remote control (optional)

RS-232C communication connector Video input and Y/C input external switching control signal input

terminal Normal(video signal input) : Open

Select Y/C input : Low(0V) Luminance signal input terminal Color signal input terminal Video signal input terminal Video input terminal 9 through-out terminal Turns on when terminates the video input terminal 9 at 75 ohm Turns on when linked to ABL Turns on when used on multi screen Switches the color temperature. 1:Normal use. 2:Re-exposure Switches VIDEO input, Y/C input, RGB input.

Switches VIDEO input and Y/C input with the external control signal

6 at VIDEO position

POWER switch

STATUS switch

RGB input terminal

RGB input select switch

RGB input terminal (Vertical sync)

RGB input terminal (Horizontal sync/composite sync)

(

RGB input terminal (B)

)

RGB input terminal (G/composite sync)

RGB input terminal (R)

• To turn off the power, use the POWER switch - of the unit, the RS-232C control, or wired remote control (optional). (If turned off using the main POWER switch or by disconnecting the power cable from the outlet, the settings of the above = to @ switches and the state of the TV SYSTEM and convergence memory will not be recorded on the memory.) Consequently when starting up or stopping the whole system by AC ON/OFF in setup conditions for a demonstration, it is necessary to turn off the power using the above method to record each setting in the memory. (Refer to "CHAPTER 4. ADJUSTMENTS, (5)Equipment Required for Adjustments".)

Tact switch

D-sub 9PIN (Male) Slide switch BNC connector BNC connector

BNC connector BNC connector

BNC connector

Power OFF : STANDBY (Red LED) lights up Power ON : ON (Green LED) lights up

Accumulated duty time: * Switch which displays setting states of each switch on the screen.

RGB signal input terminal Switches RGB signal input terminal type RGB signal vertical sync input terminal RGB signal horizontal sync and composite sync (Only for input sig-

nal H/V sync) input terminal

RGB signal B input terminal RGB signal G and composite sync (Input signal G on sync) input

terminal RGB signal R input terminal

* : Accumulated duty time

Counts only when the power is ON.

GENERAL SPECIFICATIONS

(2) Projection Screen Kit (RMS-V4011/V5011) Product Weight : 11.0 kg/14.0kg

845

(1031)

148

(148)

630

(769)

(Fig.2-4)

Accessory

Screw rivet ........................................................................................................................... 6

Unit:mm The number in parentheses is the dimentsion for RMS-V5011

GENERAL SPECIFICATIONS

(3) Projection Frame (RMF-V4011/V5011) Product Weight : 26.8kg/28.8kg

1201(1352)

845(1031)

630

(769)

(Fig.2-5)

Accessories

Metal fixture (R) ................................................................................................................... 1

Metal fixture (L) ................................................................................................................... 1

Stopper ................................................................................................................................. 2

Screw M5x10 ................................................................................................................. 38+2

Screw M5x35 ....................................................................................................................... 6

Screw M5x50 ....................................................................................................................... 4

Hexagon head bolt (with washer) M8x45 ..........................................................................8

Shield.................................................................................................................................... 1

Rivet ...................................................................................................................................... 2

Unit:mm The number in parentheses is the dimension for RMS-V5011

(7) Multi Video Processor (RMD-V3216/V3109, RMD-V2170)

1 Multi Video Processor (RMD-V3216/V3109)

Rear View

299

430

GENERAL SPECIFICATIONS

314

POWER

OFF

MULTI VIDEO PROCESSOR RMD-V3216

482.6

Front View

Main Specifications of Multi Video Processor (RMD-V3216/V3109) Input signal

Input video signal (Can be expanded up to four systems)

2-line (RMD-V3216), 1-line (RMD-V3109).... BNC terminal

1 Composite video signal ...........................................

....................................... 1.0 Vp-p (75ohm terminated)

2 Y/C separation signal

Y (With sync)................................ 1.0Vp-p (75ohm)

C burst level ............................ 0.286 Vp-p (75ohm)

*1 or 2 signal format can be selected *Only 1 has a terminate switch, throughout

Input standard sync signal.......................... BNC terminal

1 Composite sync signal ................ 0.286 to 4.0 Vp-p

2 Composite video signal

Video level ...................... 0 to 0.714 Vp-p (75ohm)

Single level ............................. 0.286 Vp-p (75ohm)

*Terminate switch, throughout

RS-232C control input 25-pin D-SUB

Output signal

Output video signal 16-line (RMD-V3216), 9-line (RMD-V3109)... BNC terminal

1 Composite sync signal ................ 1.0 Vp-p (75ohm)

2 Y/C separation signal

Y (With sync)................................. 1.0Vp-p (75ohm)

C (With burst) Burst level ....... 0.286 Vp-p (75ohm)

*1 and 2 signal formats are output simultaneously.

(Fig.2-11)

420

Side View

3 RGB signal

Green (Sync on Green) ...............................1.0 Vp-p

SYNC ........................................................... 0.3 Vp-p

B.R................................................................ 0.7 Vp-p

Output reference composite sync signal BNC terminal TTL level (Or input reference sync signal throughout)

Others

Power supply.............................. AC100 to 120V (50/60 Hz)

Power consumption.............................................................

............................ (RMD-V3216, RMD-V3109) 350W, 700VA

Operating temperature and humidity range ......................

........................................................................... 5 °C to 35 °C

Below 85% (No condensation)

External dimensions (RMD-V3216, RMD-V3109) ...............

................... 482.6 (Width)x420 (Depth)x314 (Height) (mm)

(Excluding handle)

Weight

RMD-V3216 ............................................................... 22.5 kg

RMD-V3109 ............................................................... 22.0 kg

Accessories

Rack mounting screw M5.................................................. 8

Rack mounting washer...................................................... 8

GENERAL SPECIFICATIONS

2 Multi Video Processor (RMD-V2170)

Front View

Rear View

(Fig.2-12)

Main Specifications of Multi Video Processor (RMD-V2170)

Input video signal ......................................... NTSC format

Input signal band ...................................... Above 4.2 MHz

Output

Video output

Input

Video input

Input signal ..............................................................

.....................NTSC composite video signal (BNC)

Input system ...................................................4-line

Standard input level.................... 1Vp-p (75 load)

Y/C separation

Input signal .... NTSC Y/C separation signal (BNC)

Input system ...................................................4-line

Standard input level............... Y:1 Vp-p (75 load)

.................... C:286 mVp-p (75 load burst signal)

*The video input or Y/C separation input is to be

selected by the switch on the rear panel.

Reference sync signal input

Input signal ............................. Composite sync (BNC)

Standard input level .....................................................

...................................... Composite sync 0.3 to 4 Vp-p

Control input

Input signal .... Conforms to RS-232C (25-pin, D-sub)

Y/C separation output

Test signal output

Output signal .................................................................

............................ NTSC composite video signal (BNC)

Standard output level ....................... 1Vp-p (75 load)

Sync signal output............................... TTL level (BNC)

Power supply voltage ...................... 100 to 120V, 50/60 Hz

Power consumption ....................................... 300W/500VA

External dimensions ............483 (W)x314 (H)x469 (D) mm

Weight.......................................................................... 33 kg

Side View

Output signal ............................................................

...................... NTSC composite video signal (BNC)

Output system ............................................... 16-line

Standard output level .................. 1Vp-p (75 load)

Output signal ...NTSC Y/C separation signal (BNC)

Output system ............................................... 16-line

Standard output level ...............Y1 Vp-p (75 load)

......................C286 mVp-p (75 load, burst signal)

*Line up series of RMD-V2110 with 9 OUTPUT CIRCUITS.

(8) Adjustment Control Unit (RU-V107)*Option

GENERAL SPECIFICATIONS

POWER

0 13

46 79

ADJUSTMENT CONTROL UNIT RU-V107

ADJ IN

2 5 8

Î

ABC DEF

ADJ ADJ ADJ

RGB

ON/OFF ON/OFF ON/OFF

INPUT SEL

–+

DISP CALL

MAIN MENU

ADJ OUT

187

Cable length : 5m

(Fig.2-13)

Accessories

AA dry battery (IEC R6P)......................................................................................................2

Cable (5m) ............................................................................................................................ 3

GENERAL SPECIFICATIONS

(9) Projection Cabinet (RMF-V4011R) Accessories

To attach the multi-projection unit (RM-V2400N) to the conventional RM-V2000A, the RMF-V4011R accessories (metal fixtures) are required. The following lists the required parts. For details of attaching the multi-projection unit, refer to Chapter 3. "4-(2)Assembling the System".

Frame R (BNG1207) ....................................................................................................... 1

Frame L (BNG1208) ....................................................................................................... 1

Holder (R) (BNG1150) .................................................................................................... 1

Holder (L) (BNG1151) .................................................................................................... 1

Attachment (R) (BNG1173)............................................................................................2

Attachment (L) (BNG1174) ............................................................................................ 2

Rear holder R (BNG1205) .............................................................................................. 1

Rear holder L (BNG1206) .............................................................................................. 1

Rear panel R (upper) (BMR1069) .................................................................................. 1

Rear panel L (upper) (BMR1070) .................................................................................. 1

Rear panel R (lower) (BMR1071) .................................................................................. 1

Rear panel L (lower) (BMR1072)................................................................................... 1

Cushion A (BMR1106) ................................................................................................... 1

Cushion B (BMR1107)....................................................................................................2

Hinder panel (BMR1075) ...............................................................................................2

Adjuster (BEF1011) ........................................................................................................2

Screw (M5x15) (PMB50P150FZB) ...............................................................18 (Spare 2)

Screw (M5x50) (PMB50P500FZB) ................................................................................. 4

Screw (M6x20) (PMB60P200FZB) ................................................................................. 4

Screw (3x12) (ABA1167)................................................................................................4

Screw (3x8) (BBZ30P080FZK) ..................................................................................... 10

Nut (M8) (NA80FZK) ......................................................................................................2

Note : RM-V4000V can assemble with the same accessories.

INSTALLATION AND ASSEMBLY

(9) Ventilation for system

The ventilation method differs according to where the system is installed. The following shows how to provide ventilation for the units according to the place of installation. Refer to these and keep the installation condition in the previous section [(8) Temperature and Humidity] at the system. But when installing your unit, consult your dealer.

1 When there are no walls on all sides (within 1m)

As shown in Fig. 3-3, attach the top panel, side panel, and rear panel.

(Note) When attaching the rear panel, be careful not to block the vents for the fan of the projection unit.

2 When there is a wall at the back *

As shown in Fig. 3-5, mount a large fan to the top panel, provide vents for inhaling air at the bottom panel to blow out air inside. Always leave more than 300 mm between the wall and the back of the unit.

(Fig. 3-3)

3 When blocking the bottom (when placing the projection unit on the floor directly) *

Same as 1. (Fig. 3-6)

<Note> *: There should be no obstacles within the 1m area of the

unit except for the rear and bottom. If this condition is

not followed, construct your own ventilation system

(large fan, low temperature by air-conditioning, etc.)

(Fig. 3-6)

according to the site of use.

(Fig. 3-5)

+ 112 hidden pages