Pioneer PDP-504CMX-S, PDP 504CMX, PDP 434CMX User Manual

Plasma Display Écran à plasma

PDP-504CMX PDP-504CMX-S PDP-434CMX

Contents related to system specifications, power requirements, accessories, and other information differ with respect to the country where this unit is purchased. For customers living in the U.S.A. or Canada, please use and refer to the instructions written in either English or French. For customers in Japan, please use and refer to the instructions written in Japanese.

Les caractéristiques, les spécifications d'alimentation, les accessoires et d'autres informations diffèrent d'un pays à l'autre. Si vous vivez au Canada ou aux États-Unis, reportezvous aux instructions en français ou en anglais. Si vous vivez

au Japon, reportez-vous aux instructions en japonais.

電源、付属品などの差異がありますので、日本国内でご購入･ご使用の際は、本書の日本語ページをご覧ください。その他の国、地域でご購入･ご使用の際は、英語またはフランス語ページをご覧ください。

Operating Instructions Mode d’emploi

「据付工事」について

●

本機は十分な技術・技能を有する専門業者が据付けを行うことを前提に販売されているものです。据付け・取付けは必ず工事専門業者または販売店にご依頼ください。

●

なお、据付け・取付けの不備、誤使用、改造、天災などによる事故損傷については、弊社は一切責任を負いません。

K042_Ja

販売店様へ

この取扱説明書は据え付け終了後お客様に必ずお渡しして、取り扱い方法の説明を行ってください。

English This unit has been designed for use as a computer display monitor. The optional video card is required if you wish to view other video signals on the monitor. For details consult your local retail dealer.

Français Cet appareil est conçu pour une utilisation comme moniteur d’affichage d’ordinateur. La carte vidéo optionnelle est nécessaire si vous souhaitez regarder d’autres signaux sur ce moniteur. Pour plus de renseignements, consultez votre revendeur.

English

Operating Instructions

Thank you very much for purchasing this PIONEER product. Before using your Plasma Display, please read the “Safety Precautions” and these “Operating Instructions” carefully so you will know how to operate the Plasma Display properly. Keep this manual in a safe place. You will find it useful in the future.

Notes on Installation Work:

This product is marketed assuming that it is installed by qualified personnel with enough skill and competence. Always have an installation specialist or your dealer install and set up the product. PIONEER cannot assume liabilities for damage caused by mistake in installation or mounting, misuse, modification or a natural disaster.

Français

Note for Dealers:

After installation, be sure to deliver this manual to the customer and explain to the customer how to handle the product.

Safety Precautions

IMPORTANT

English

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

WARNING:

The apparatus is not waterproofs, to

CAUTION:

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

prevent fire or shocks hazard, do not expose this apparatus to rain or moisture and do not put any water source near this apparatus, such as vase, flower pot, cosmetics container and medicine bottle etc.

D3-4-2-1-3_En

IMPORTANT NOTICE

The serial number for this equipment is located on the rear panel. Please write this serial number on your enclosed warranty card and keep it in a secure area. This is for your security.

WARNING: Handling the cord on this product or cords associated with accessories sold with the product will expose you to lead, a chemical known to the State of California and other governmental entities to cause cancer and birth defects or other reproductive harm.

Wash hands after handling

D36-P4_En

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

D3-4-2-1-1_En-A

The following symbols are found on labels attached to the product. They alert the operators and service personnel of this equipment to any potentially dangerous conditions.

WARNING

This symbol refers to a hazard or unsafe practice which can result in personal injury or property damage.

CAUTION

This symbol refers to a hazard or unsafe practice which can result in severe personal injury or death.

CAUTION: WHEN POSITIONING THIS EQUIPMENT

ENSURE THAT THE MAINS PLUG AND SOCKET IS EASILY ACCESSIBLE.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

Safety Precautions

a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help.

Information to User

Alteration or modifications carried out without appropriate authorization may invalidate the user’s right to operate the equipment.

CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded cables and connectors for connections.

D8-10-1-2_En

D8-10-2_En

D8-10-3a_En

IMPORTANT SAFETY INSTRUCTIONS

READ INSTRUCTIONS — All the safety and operating

instructions should be read before the product is operated.

RETAIN INSTRUCTIONS — The safety and operating

instructions should be retained for future reference.

HEED WARNINGS — All warnings on the product and

in the operating instructions should be adhered to.

FOLLOW INSTRUCTIONS — All operating and use

instructions should be followed.

CLEANING — Unplug this product from the wall outlet

before cleaning. The product should be cleaned only with a polishing cloth or a soft dry cloth. Never clean with furniture wax, benzine, insecticides or other volatile liquids since they may corrode the cabinet.

ATTACHMENTS — Do not use attachments not

recommended by the product manufacturer as they may cause hazards.

WATER AND MOISTURE — Do not use this product

near water — for example, near a bathtub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

ACCESSORIES — Do not place this product on an

unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

CART — A product and cart combination should be

moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

VENTILATION — Slots and openings in the cabinet

are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

POWER SOURCES — This product should be operated

only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company.

LOCATION — The appliance should be installed in a

stable location.

NONUSE PERIODS — The power cord of the

appliance should be unplugged from the outlet when left unused for a long period of time.

GROUNDING OR POLARIZATION

÷ If this product is equipped with a polarized

alternating current line plug (a plug having one blade wider than the other), it will fit into the outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

÷ If this product is equipped with a three-wire

grounding type plug, a plug having a third (grounding) pin, it will only fit into a grounding type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding type plug.

POWER-CORD PROTECTION — Power-supply cords

should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

OUTDOOR ANTENNA GROUNDING — If an outside

antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure A.

LIGHTNING — For added protection for this product

during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

POWER LINES — An outside antenna system should

not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

OVERLOADING — Do not overload wall outlets,

extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

GROUND CLAMP

Safety Precautions

OBJECT AND LIQUID ENTRY — Never push objects

of any kind into this product through openings as they may touch dangerous voltage points or shortout parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

SERVICING — Do not attempt to service this product

yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

DAMAGE REQUIRING SERVICE — Unplug this

product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

÷ When the power-supply cord or plug is damaged. ÷ If liquid has been spilled, or objects have fallen

into the product.

÷ If the product has been exposed to rain or water. ÷ If the product does not operate normally by

following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.

÷ If the product has been dropped or damaged in

any way.

÷ When the product exhibits a distinct change in

performance — this indicates a need for service.

REPLACEMENT PARTS — When replacement parts

are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

SAFETY CHECK — Upon completion of any service

or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

HEAT — The product should be situated away from

heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

WALL OR CEILING MOUNTING — The product

should be mounted to a wall or ceiling only as recommended by the manufacturer.

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

English

Français

Safety Precautions

ELECTRIC SERVICE EQUIPMENT

Figure A

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

NEC – NATIONAL ELECTRICAL CODE

iii

Safety Precautions

English

FEDERAL COMMUNICATIONS COMMISSION

DECLARATION OF CONFORMITY

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Product Name: Plasma Display with Video Card

Safety Precautions

Model Number: PDP-504CMX / PDP-434CMX (Plasma Display)

PDA-5003/PDA-5004 (Video Card)

Product Category: Class B Personal Computers & Peripherals

Responsible Party Name: PIONEER ELECTRONICS (USA) INC. Customer Support Division

Address: P.O. BOX 1760, LONG BEACH, CA., 90801-1760 U.S.A.

Phone: (800)421-1625

URL: http://www.pioneerelectronics.com

Should this product require service in the U.S.A. and you wish to locate the nearest Pioneer Authorized Independent Service Company, or if you wish to purchase replacement parts, operating instructions, service manuals, or accessories, please call the number shown below.

8 0 0 – 8 7 2 – 4 1 5 9

Please do not ship your product to Pioneer without first calling the Customer Support Division at the above listed number for assistance.

Pioneer Electronics (USA) Inc. Customer Support Division P.O. BOX 1760, Long Beach, CA 90801-1760, U.S.A.

For warranty information please see the Limited Warranty sheet included with your product.

Should this product require service in Canada, please contact a Pioneer Canadian Authorized Dealer to locate the nearest Pioneer Authorized Service Company in Canada. Alternatively, please contact the Customer Satisfaction Department at the following address:

iii

Pioneer Electronics of Canada, Inc. Customer Satisfaction Department 300 Allstate Parkway, Markham, Ontario L3R OP2 (905)479-4411 1(877)283-5901

For warranty information please see the Limited Warranty sheet included with your product.

S021_EF

Contents

Features

Safety Precautions ................................... i

Features ................................................... 1

Before Proceeding ...................................3

How to use this manual...................................... 3

Checking supplied accessories .......................... 5

Part Names and Functions ..................... 6

Main unit.............................................................. 6

Remote control unit ............................................ 7

Connection panel ................................................ 8

Installation and Connections ............... 10

Installation of the unit....................................... 10

Connection to a personal computer ................ 12

Audio connections ............................................ 13

Power cord connection..................................... 14

How to route cables .......................................... 15

System Settings .................................... 16

Setting the onscreen display language........... 16

Settings after connections ............................... 17

Operation ............................................... 19

Selecting input source ...................................... 19

Adjusting sound volume .................................. 20

Muting the sound.............................................. 20

Confirming current status ................................ 20

Changing screen size ........................................ 21

Enlarging one part of the screen

(POINT ZOOM) .................................................. 22

Multiscreen display........................................... 23

Automatic power-off

(POWER MANAGEMENT) ................................ 24

PICTURE/SCREEN Adjustment ............ 25

PICTURE adjustment ........................................ 25

Adjusting screen POSITION, CLOCK, and PHASE

<automatic adjust> ........................................... 26

Adjusting screen POSITION, CLOCK, and PHASE

<manual adjust> ............................................... 27

Other Operations .................................. 29

Setting the orbiter (ORBITER) .......................... 29

Side mask position (MASK CONTROL) ........... 29

Screen management settings

(SCREEN MGT.) ................................................. 30

Energy saving settings (ENERGY SAVE) ......... 31

Automatic input switching

(AUTO FUNCTION) ........................................... 32

About audio output (AUDIO OUT)................... 33

Additional Information ......................... 34

Cleaning ............................................................. 34

Troubleshooting ................................................ 34

Precautions regarding use ............................... 36

STANDBY and ON indicators ........................... 36

Specifications .................................................... 37

Appendix 1: Computer signal

compatibility table ............................................ 38

Appendix 2: INPUT1/2 pin assignments ......... 42

Explanation of terms ........................................ 42

PDP-504CMX

Introduces newly developed 50" XGA Wide Plasma Panel

The new wide high-precision XGA 50" plasma panel (1280x768 / 16:9) pushes the envelope of previous high-luminance panels, producing brighter, clearer images with higher contrast.

¶ Newly developed image processing technology

(P.U.R.E. Drive) reproduces images with higher definition and quality

The newly developed fully digital image processing circuitry (P.U.R.E. Drive) designed exclusively for Pioneer’s high-definition plasma displays allows the reproduction of clearer, brighter images.

¶ ES Slot interface for enhanced potential

The display is provided with a built-in ES Slot Interface to allow the installation of cards for the connection of external devices, thus enhancing its expansion potential.

¶ Supports wide range of computer signals (analog/

digital)

Supports non-compressed display of signals ranging from 640x400 and 640x480 (VGA) to 1024x768 (XGA) and 1280x768, and compressed display of 1280x1024 (SXGA), 1400x1050 (SXGA+) and 1600x1200 (UXGA), signals. Further, aspect ratio and screen size settings supported include [DOT BY DOT], [4:3], [FULL] and [PARTIAL](*1). * Supported signals are different on INPUT1 and INPUT2. *1 Aspect ratio and screen size appearance will differ depending

on input signal.

¶ Free Installation Configuration

– Broader installation possibilities with thinner, lighter, high-endurance design –

While producing a large 50" screen image, the display is only 98 mm thick, and weighs in at only 41.0 kg. On the other hand, the efficient heat-radiating design greatly improves environmental operating conditions. The thinner, lighter design, coupled to highendurance construction greatly broadens the range of possible installation locations and styles.

¶ High reliability for commercial applications

This display is provided with features giving it high dependability in commercial applications, including the ability to suppress peak luminance in accordance with the viewing program, and to change the cooling fan’s speed in accordance with changes in operating environment. Such features provide safety and highendurance under conditions of commercial use.

¶ Improved usability

User convenience has been improved by the inclusion of features making the display even more compatible with your computer. Some of these include the one-touch screen adjustment, [AUTO SET UP] function for computer connections, and the POINT ZOOM function to enlarge local portions of the screen image to display important detailed program data.

¶ Power-Saving Design

While equipped with a high-precision (1280x768) panel, this unit achieves the highest energy-saving of any display in its class (50inch XGA class: 360 W). In addition, when the [ENERGY SAVE] function is selected, power consumption is reduced by 20 % compared to the normal operating mode (MODE1, with color-bar signal input). The display is also provided with a variety of power-saving functions, including an automatic brightness function with ambient light sensor.

English

Features

PDP-434CMX

¶ Introduces newly developed 43" Wide Plasma Panel

English

The new wide high-precision 43" plasma panel (1024x768 / 16:9) pushes the envelope of previous high-luminance panels, producing brighter, clearer images with higher contrast.

¶ Newly developed image processing technology

(P.U.R.E. Drive) reproduces images with higher definition and quality

The newly developed fully digital image processing circuitry (P.U.R.E. Drive) designed exclusively for Pioneer’s high-definition plasma displays allows the reproduction of clearer, brighter images.

¶ ES Slot interface for enhanced potential

The display is provided with a built-in ES Slot Interface to allow the installation of cards for the connection of external devices, thus enhancing its expansion potential.

¶ Supports wide range of computer signals (analog/

digital)

Supports non-compressed display of signals ranging from 640x400 and 640x480 (VGA) to 1024x768 (XGA), and compressed display of 1280x1024 (SXGA), 1400x1050 (SXGA+) and 1600x1200 (UXGA) signals. Further, aspect ratio and screen size settings supported include [DOT BY DOT], [4:3], [FULL] and [ZOOM](*1). * Supported signals are different on INPUT1 and INPUT2. *1 Aspect ratio and screen size appearance will differ depending

on input signal.

¶ Free Installation Configuration

– Broader installation possibilities with thinner, lighter, high-endurance design –

While producing a large 43" screen image, the display is only 98 mm thick, and weighs in at only 32.5 kg. On the other hand, the efficient heat-radiating design greatly improves environmental operating conditions. The thinner, lighter design, coupled to highendurance construction greatly broadens the range of possible installation locations and styles.

¶ High reliability for commercial applications

Features

operating environment. Such features provide safety and highendurance under conditions of commercial use.

¶ Improved usability

¶ Power-Saving Design

While equipped with a high-precision (1024x768) panel, this unit achieves the highest energy-saving of any display in its class (43inch class: 298 W). In addition, when the [ENERGY SAVE] function is selected, power consumption is reduced by 20 % compared to the normal operating mode (MODE 1, with color-bar signal input). The display is also provided with a variety of power-saving functions, including an automatic brightness function with ambient light sensor.

¶ Optional line (sold separately)

(For details, please consult the dealer where this unit was purchased.)

1 Table top stand: PDP-504CMX/PDP-434CMX display stand.

2 Wall installation unit:

Speaker system designed specifically for plasma displays (width: 7.4 cm (2-29/32 in.)): 2-way speaker units featuring 2.5

4 Video card: Expansion card allows viewing of video signals

Wall installation bracket designed as a wall interface for securing the unit.

cm (31/32 in.) dome conical tweeter and newly developed 14.6 cm (5-3/4 in.) x 6.2 cm (2-7/16 in.) eliptical speaker in vertical arrangement. (When speakers are attached, the operation panel on this unit is not operable.)

and computer analog RGB signals. Cards used in the expansion slots should be manufactured or recommended by Pioneer. Using other expansion cards may result in malfunction.

Before Proceeding

How to use this manual

This manual is set up to follow the course of actions and operations in the order that would seem most logical for someone setting up this unit.

Once the unit has been taken out of the box and it has been confirmed that all the parts have been received (page 5), it may be beneficial to look over the section “Part Names and Functions” starting on page 6 to become acquainted with the plasma monitor and remote control unit, as their respective buttons and controls will be referred to throughout this manual.

The section “Installation and Connections” starting on page 10 covers all the necessary points regarding installation of the plasma display and connections to a wide variety of components.

The section “System Settings” starting on page 16 covers the on-screen settings necessary for correct operation of the plasma display with its connected components. Depending on the connections made, this section may or may not be necessary.

The remainder of the sections in this manual is dedicated to the basic operations associated with selecting a source component up to the more complex operations associated with adjusting the plasma display picture to match the requirements of specific components and personal preferences.

Regarding menu displays

The example menu displays provided in this manual are those for the PDP-504CMX model. The PDP-434CMX display differs as shown:

Example of PDP-504CMX Menu Display:

MENU INPUT1

PICTURE SCREEN SETUP OPTION

ENTER

: : : : : :

0 0 0 0 0 0

EXIT

CONTRAST

BRIGHTNESS R.LEVEL G.LEVEL B.LEVEL H.ENHANCE V.ENHANCE

PICTURE RESET

SET

Example of PDP-434CMX Menu Display:

MENU INPUT1

PICTURE SCREEN SETUP OPTION

CONTRAST

BRIGHTNESS R.LEVEL G.LEVEL B.LEVEL H.ENHANCE V.ENHANCE

PICTURE RESET

SET

ENTER EXIT

Please note that the actual contents displayed are the same for both the PDP-504CMX and PDP-434CMX.

English

Before Proceeding

About operations in this manual

Each operation is described in its proper operating order.

English

These Operating Instructions will refer to the operating controls found on the remote control unit, with the exception of those buttons found only on the main plasma display itself. When the plasma display controls include equivalent buttons to those found on the remote control unit, the commands can be performed on the main unit as well.

The following illustrations are an example of the actual operations used for the section “PICTURE adjustment”. The examples are provided to allow you to confirm whether the operation is performed correctly or not.

PICTURE/SCREEN Adjustment

PICTURE adjustment

5/∞

2/3

SET

Before Proceeding

Main unit operating panel

1 Press the MENU button to display the menu

screen.

MENU INPUT1

PICTURE SCREEN SETUP OPTION

CONTRAST

BRIGHTNESS R.LEVEL G.LEVEL B.LEVEL H.ENHANCE V.ENHANCE

PICTURE RESET

2 Use the 5/∞ buttons to select the adjustment

item, then press the SET button.

MENU INPUT1

PICTURE SCREEN SETUP OPTION CONTRAST

BRIGHTNESS

R.LEVEL G.LEVEL B.LEVEL H.ENHANCE V.ENHANCE

PICTURE RESET

SET

ENTER

Remote control unit

: : : : : :

: : : : :

Note

The screen images depicted in these Operating Instructions should be considered typical images; some difference will be seen in practice, depending on the screen item displayed and its contents, the input source and various other control settings.

4 Press the SET button.

Pressing the SET button writes the value into the memory and returns the display to the step 2 screen.

5 When the setup is finished, press the MENU

button to exit the menu screen.

Note

Make these adjustments for each input (INPUT1 or INPUT2) and signals.

[PICTURE] mode adjustment items

MENU 2/3

SET 5/∞

0 0 0 0 0 0

EXIT

0 0 0 0 0

Below are brief descriptions of the options that can be set in the [PICTURE] mode.

CONTRAST ············· Adjust according to the surrounding

BRIGHTNESS ·········· Adjust so that the dark parts of the

R. LEVEL ················· Adjust the amount of red in the

G. LEVEL ················· Adjust the amount of green in the

B. LEVEL ················· Adjust the amount of blue in the

H. ENHANCE··········· Sharpens the image in the horizontal

V. ENHANCE ··········· Sharpens the image in the vertical

To reset [PICTURE] mode settings to the default

If settings have been adjusted excessively or the picture on the screen no longer appears natural, it may prove more beneficial to reset the [PICTURE] mode to default settings instead of trying to make adjustments under already adjusted conditions.

1 In step 2 in the previous procedure, use the 5/∞

buttons to select [PICTURE RESET], then press the SET button.

brightness so that the picture can be seen clearly.

picture can be seen clearly.

picture.

direction.

English

PICTURE/SCREEN Adjustment

SET

ENTER EXIT

3 Use the 2/3 buttons to adjust the picture quality

as desired.

BRIGHTNESS

SET EXIT

PICTURE RESET

YES

SET

2 Use the 2/3 buttons to select [YES], and press

the SET button.

All [PICTURE] mode settings are returned to the factory set default.

EXIT

Before Proceeding

Checking supplied accessories

Check that the following accessories were supplied.

1 Power cord

2 Remote control unit

3 AA (R6) batteries (x 2)

7 Display stands (x 2)

8 Washers (x 2)

9 Hex hole bolts (x 2)

0 Remote control unit holder

English

4 Cleaning cloth (for screen)

5 Speed clamps (x 2)

6 Bead bands (x 2)

Use as a holder for the remote control unit. When attaching to the rear of the main unit, be careful not to cover the vents.

÷ These Operating Instructions ÷ Warranty

Before Proceeding

Part Names and Functions

Main unit

English

Main unit

PDP-504CMX

345

PDP-434CMX

Operation panel on the main unit

8 9

= ~ !

Note

When optional speakers have been connected, the operation panel on the main unit will not be operable.

Main unit

1 Display stand 2 Remote control sensor

Point the remote control toward the remote sensor to operate the unit (page 8).

3 Ambient light sensor

This sensor measures the level of light inside the viewing room; it is enabled when the [ENERGY

Part Names and Functions

SAVE] option is set to [AUTO] (page 31).

4 ON indicator

Lights green when the plasma display is operating (page 19). When flashing, the indicator is used to indicate error messages (page 36). The indicator flashes green once every one second when the [POWER MANAGEMENT] function is operating (page 24).

5 STANDBY indicator

Lights red when the unit is in standby mode (page 19). When flashing, the indicator is used to indicate error messages (page 36).

6 Handles

The plasma displays PDP-504CMX and PDP-434CMX utilize differing methods of handle attachment, but the handles themselves are used in the same way (page

11).

Operation panel on the main unit

7 STANDBY/ON button

Press to put the display in operation or standby mode (page 19).

8 INPUT button

Press to select the input (page 19).

9 MENU button

Press to open and close the on-screen menu (pages 16 to 33).

0 ADJUST ( / / / ) buttons

Use these buttons to move the onscreen cursor between selection options, and to perform adjustments. Instructions for use are given with each command option onscreen (pages 16 to 33).

- VOLUME (+/–) buttons

When not indicated for use in onscreen menu items, these buttons are used for adjusting the sound volume (pages 19 and 20).

= SET/DISPLAY button

Use to confirm onscreen menu selections, and to change settings (pages 16 to 33). When not indicated by onscreen menus, used to display the current set status (page 20).

~ SCREEN SIZE button

Press to select the screen size (page 21).

! AUTO SET UP button

When using computer signal input, automatically sets the [POSITION], [CLOCK] and [PHASE] to optimum values (page 26).

Remote control unit

Part Names and Functions

1 SCREEN SIZE button

Press to select the screen size (page 21).

2 INPUT buttons

Press to select the input (page 19).

3 MENU button

Press to open and close the on-screen menu (pages 16 to 33).

4 ADJUST (5/∞/3/2) buttons

Use to navigate menu screens and to adjust various settings on the unit (pages 16 to 33).

5 SET button

Press to adjust or enter various settings on the unit (pages 16 to 33).

6 SUB INPUT button

During multi-screen display, use this button to change inputs to subscreens (page 23).

English

5 6

7 8

When handling the remote control unit

¶ Do not drop the remote control unit or expose it to

moisture.

¶ Do not use the remote control unit in a location subject to

direct sunlight, heat radiation from a heater, or in a place subject to excessive humidity.

¶ When the remote control unit’s batteries begin to wear out,

the operable distance will gradually become shorter. When this occurs, replace all batteries with new ones as soon as possible.

~ !

7 SPLIT button

Press to switch to multi-screen display (page 23).

8 MUTING button

Press to mute the volume (page 20).

9 AUTO SET UP button

When using computer signal input, automatically sets the [POSITION], [CLOCK] and [PHASE] to optimum values (page 26).

0 STANDBY/ON button

Press to put the unit in operation or standby mode (page 19).

- DISPLAY button

Press to view the unit’s current input and setup mode (page 20).

Part Names and Functions

= POINT ZOOM button

Use to select and enlarge one part of the screen (page

22).

~ SWAP button

During multi-screen display, use this button to switch between main screen and subscreen (page 23).

! PIP SHIFT button

When using PinP mode with multi-screen display, use this button to move the position of subscreen (page

23).

@ VOLUME (+/–) buttons

Use to adjust the volume (pages 19 and 20).

Part Names and Functions

Operating range of the remote

English

Part Names and Functions

control unit

When operating the remote control unit, point it at the remote sensor (Î) located on the front panel of the main unit. The remote control unit is operable up to 7 m from the unit and within a 30 angle on each side of the sensor.

7 m (23 feet)

If you are having difficulty with operation of the remote control unit

¶ The remote control unit may not operate if there are

objects placed between it and the display.

¶ Operational distance will gradually become shorter as the

batteries begin to wear out, replace weak batteries with new ones as soon as possible.

¶ This unit discharges infrared rays from the screen. Placing a

video deck or other component that is operated by an infrared remote control unit near this unit may hamper that component’s reception of the remote control’s signal, or prevent it from receiving the signal entirely. Should this occur, move the component to a position further away from this unit.

¶ Depending on the installation surroundings, this unit’s

remote control unit may be influenced by the infrared rays discharged from the plasma display, hampering reception of its rays or limiting its operational distance. The strength of infrared rays discharged from the screen will differ according to the picture displayed.

30°

Remote Sensor

Inserting the batteries in the remote control unit

While pressing down lightly, slide in the direction of the arrow.

Two AA (R6) batteries

CAUTION

¶ Insert batteries so that the plus (+) and minus (–) sides

are aligned according to the markings in the battery case.

¶ When not using the remote control unit for a long period

of time (1 month or more), remove the batteries from the remote control unit to prevent leaking of battery fluid. If battery liquid has leaked, thoroughly wipe the inside of the case until all liquid is removed, and then insert new batteries.

When disposing of used batteries, please comply with governmental regulations or environmental public instruction’s rules that apply in your country/area.

D3-4-2-3-1_En

NO!

¶ Do not mix new batteries with used ones. ¶ The voltage of batteries may differ even if they are the

same shape. Please do not mix different kinds of batteries together.

¶ Do not charge, short, disassemble or throw the provided

batteries in a fire.

Connection panel

The connection panel is provided with two video input terminals and one video output terminal. Audio input/ output and speaker output terminals are also provided. For instructions regarding connections, consult the pages noted in parentheses by each item.

1 SPEAKER (R) terminal

For connection of an external right speaker. Connect a speaker that has an impedance of 8 -16 Ω (page 13).

2 COMBINATION IN/OUT

Never connect any component to these connectors without first consulting your Pioneer installation technician.

These connectors are used for plasma display setup adjustments.

Illustration depicts PDP-504CMX model.

Part Names and Functions

English

SPEAKER 8Ω ~16Ω

+ –

IN OUT

COMBINATION

3 RS-232C

Never connect any component to this connector without first consulting your Pioneer installation technician.

This connector is used for plasma display setup adjustments.

4 ANALOG RGB IN (INPUT1) (mini D-sub 15 pin)

For connection of a personal computer (PC) or similar component. Make sure that the connection made corresponds to the format of the signal output from the connected component (page 12).

5 ANALOG RGB OUT (INPUT1) (mini D-sub 15 pin)

Use the ANALOG RGB OUT (INPUT1) terminal to output the video signal to an external monitor or other component.

Note: The video signal will not be output from the ANALOG RGB OUT (INPUT1) terminal when the main power of this unit is off or in standby mode. (page 12)

6 AUDIO (INPUT1) (Stereo mini jack)

Use to obtain sound when INPUT1 is selected. Connect the audio output jack of components connected to INPUT1 to this unit (page 13).

RS-232C

POWER

OFF

AC IN

SPEAKER 8Ω ~16Ω

+ –

=-0

ANALOG RGB IN

D-Sub

ANALOG RGB OUT

4 5 6

INPUT1 INPUT2 OUTPUT

D-Sub

DIGITAL RGB

AUDIO AUDIO AUDIO

DVI-D

7 8 9

8 AUDIO (INPUT2) (Stereo mini jack)

Use to obtain sound when INPUT2 is selected. Connect the audio output jack of components connected to INPUT2 to this unit (page 13).

9 AUDIO (OUTPUT) (Stereo mini jack)

Use to output the audio of the selected source component connected to this unit to an AV amplifier or similar component.

Note: No sound is produced from the AUDIO (OUTPUT) jack when the MAIN POWER switch is set to OFF or ON (standby) (page 13).

0 MAIN POWER switch

Use to switch the main power of the unit on and off.

- AC IN

Use to connect the supplied power cord to an AC outlet (page 14).

= SPEAKER (L) terminal

For connection of an external left speaker. Connect a speaker that has an impedance of 8 -16 Ω (page 13).

Part Names and Functions

7 DIGITAL RGB (INPUT2) (DVI-D jack)

Use to connect a computer.

Note: This unit does not support the display of copyguard-protected video signals (page 12).

Installation and Connections

Installation of the unit

English

Installation using the supplied display stands

Be sure to fix the supplied stands to the installation surface. Use commercially available M8 bolts that are 25 mm (1 in.) longer than the thickness of the installation surface.

1 Fix the supplied stands to the installation surface

at each of the 4 prepared holes using commercially available M8 bolts.

Front

PDP-504CMX: 798 mm (31-7/16 in.) (Bolt hole thread pitch)

Rear

Always install the supplied display stands according to the dimensions shown in the accompanying illustration.

110 mm (4-5/16 in.)

2 Set this unit in the stands.

PDP-434CMX: 880 mm (31-7/16 in.) (Bolt hole thread pitch)

Installation using the optional PIONEER stand or installation bracket

÷ Please be sure to request installation or mounting of this unit

or the installation bracket by an installation specialist or the dealer where purchased.

÷ When installing, be sure to use the bolts provided with the

stand or installation bracket.

÷ For details concerning installation, please refer to the

instruction manual provided with the stand or installation bracket.

Installation using accessories other than the PIONEER stand or installation bracket (sold separately)

÷ When possible, please install using parts and accessories

manufactured by PIONEER. PIONEER will not be held responsible for accident or damage caused by the use of parts and accessories manufactured by other companies.

÷ For custom installation, please consult the dealer where the

unit was purchased, or a qualified installer.

Wall-mount installation of the unit

This unit has been designed with bolt holes for wall-mount installation, etc. The installation holes provided are shown in the accompanying illustration.

÷ Be sure to attach in 4 or more locations above and

below, left and right of the center line.

÷ Use bolts that are long enough to be inserted 12 mm

(

/2 in.) to 18 mm (11/16 in.) into the main unit from the attaching surface for both a holes and b holes. Refer to the side view diagram in the accompanying illustration.

÷ As this unit is constructed with glass, be sure to install

it on a flat, unwarped surface.

Installation and Connections

3 Fix this unit using the supplied washer and bolt.

Use a 6 mm (1/4 in.) hex

CAUTION

This display unit weighs at least 30 kg (67 lbs) and has little frontto-back depth, making it very unstable when stood on edge. As a result, two or more persons should cooperate when unpacking, moving, or installing the display.

wrench to bolt them.

CAUTION

To avoid malfunction, overheating of this unit, and possible fire hazard, make sure that the vents on the main unit are not blocked when installing. Also, as hot air is expelled from the air vents, be careful of deterioration and dirt build up on rear surface wall, etc..

CAUTION

Please be sure to use an M8 (Pitch = 1.25 mm) bolt. (Only this size bolt can be used.)

CAUTION

This unit incorporates a thin design. To ensure safety if vibrated or shaken, please be sure to take measures to prevent the unit from tipping over.

Installation and Connections

CAUTION

÷ Handles should not be removed or reattached by anyone other

than the professional installation technician or service personnel.

÷ If handles must be removed due to specific installation

conditions, the mounting screws should be stored carefully together with the handles. To ensure safety, the mounting screws should be tightened to a minimum torque of 2N·m (20 kgf·cm) when reattaching the handles.

÷ When moving the display, it should always be carried by two

persons holding the rear handles in the manner shown.

Air vents (fan)

b hole

a hole

b hole

a hole

NO!

÷ Never attempt to move the plasma display by holding only one

of the handles.

÷ When installing the plasma display, do not use the handles as

means of hanging the display; also do not use them as devices to prevent tipping over (see illustration).

Attaching surface

Installation bracket, etc..

Main unit

Center line

b hole

a hole

Bolt

English

Français

b hole

Center line

Rear view diagram (PDP-504CMX)

Air vents (fan)

a hole

Center line

Rear view diagram (PDP-434CMX)

b holeb hole

a hole

b holeb hole

Center line

b hole

12 mm to 18 mm

Side view diagram

12 mm to 18 mm (1/2 in. to 11/16 in.)

Bolt

(1/2 in. to 11/16 in.)

Installation and Connections

Connection to a personal computer

English

Connection method differs depending on the computer type. When connecting, please thoroughly read the computer’s instruction manual.

Before making connections, be sure to make sure that the personal computer’s power and this unit’s main power is off.

When connecting to ANALOG RGB OUT (INPUT1)

ANALOG RGB IN

D-Sub

ANALOG RGB OUT

D-Sub

INPUT1

AUDIO

Connection to INPUT1

Connect the display’s D-sub input connector to the D-sub output (analog RGB) from the computer. This connector also supports G ON SYNC (output with green signal combined with sync signal), and composite SYNC (output with combined horizontal and vertical sync signals).

When connecting to ANALOG RGB IN (INPUT1)

ANALOG RGB IN

D-Sub

ANALOG RGB OUT

D-Sub

Connect the cable corresponding to the shape of the input terminal on this unit and the personal computer’s output terminal.

Installation and Connections

Secure by tightening the terminal screws on both units.

INPUT1

AUDIO

To an external monitor

With this unit, it is possible to output the video signal to an external monitor or other component from the ANALOG RGB OUT (INPUT1) terminal.

Note

A video signal will not be output from the ANALOG RGB OUT (INPUT1) terminal when the main power of this unit is off or in standby.

Connection to INPUT2

A computer equipped with DVI output (digital RGB signal) can be connected to the video card’s DVI connector.

DVI-D

INPUT2

AUDIO

DIGITAL RGB

Following completing connections, on-screen setup is necessary. See pages 16 to 18 for details.

Note

Depending on the type of computer model being connected, a conversion connector or adapter etc. provided with the computer or sold separately may be necessary. For details, please read your PC’s instruction manual or consult the maker or nearest dealer of your computer.

NOTICE

¶ INPUT1 supports Microsoft “Plug & Play” (VESA DDC 1/2B)

components. See Appendix 2-1/2 (page 42) when making connections to INPUT1.

¶ See Appendix 1 (pages 38 and 40) for information regarding

signals and display formats supported by INPUT1.

Following completing connections, on-screen setup is necessary. See pages 16 to 18 for details.

Notes

¶ Use a DVI-D 24-pin (digital only) cable for the connection. ¶ This unit does not support the display of copyguard-protected

video signals.

NOTICE

¶ INPUT2 supports Microsoft “Plug & Play” (VESA DDC 2B)

components. See Appendix 2-2/2 (page 42) when making connections to INPUT2.

¶ See Appendix 1 (pages 39 and 41) for information regarding

signals and display formats supported by INPUT2.

Audio connections

Before making connections, be sure to check that the audio component’s power and the unit’s main power is off.

Connecting the speakers

This unit is equipped with speaker output terminals for connection to the speaker system (not supplied) specially designed for use with this unit. Refer to the illustrations below when making connections to the speaker terminals on this unit.

12 mm

Notes

÷ After connecting the wires, pull gently on the cables to confirm

that the wire cores are fastened securely in their terminals. Insecure connections will result in noise or interrupted sound.

÷ Do not allow the wire cores of the ª and · speaker cables to

protrude excessively, since they may touch each other, causing a short circuit. This will produce excessive load on the plasma display, causing operation to malfunction or stop.

Connection to audio output connector

Use a stereo miniplug to connect the plasma display’s AUDIO (OUTPUT) stereo mini jack (L/R) to an AV amplifier or other component.

OUTPUT

DVI-D

INPUT2

AUDIO AUDIO

DIGITAL RGB

Twist exposed wire strands together.

Push tab to the open position, and insert the wire. Then, close tab firmly to secure the wire in place.

Installation and Connections

Audio connections for component (computer) connected to INPUT1

DVI-D

INPUT1

AUDIO

INPUT2

AUDIO

ANALOG RGB OUT

D-Sub

A stereo miniplug cable can be used to connect the audio output from the component connected to INPUT1, to the plasma display’s AUDIO (INPUT1) stereo mini jack (L/R).

Sound is output from both the AUDIO (OUTPUT) stereo mini jack (L/R) and the SPEAKER (L/R) terminals according to the video input selection.

Audio connections for component (computer) connected to INPUT2

DIGITAL RGB

English

Français

Making connections to the audio inputs on this unit

This unit features two audio inputs and one audio output. The following chart shows the video inputs and the corresponding audio input terminals.

Video

input

INPUT1

INPUT2

Audio input jacks Sound output

Stereo mini jack (L/R) Stereo mini jack (L/R)

Sound of the selected video input is output from the

• SPEAKER (L/R) terminals

• Stereo mini jack (L/R)

Installation and Connections

A stereo miniplug cable can be used to connect the audio output from the component connected to INPUT2, to the plasma display’s AUDIO (INPUT2) stereo mini jack (L/R).

Sound is output from both the AUDIO (OUTPUT) stereo mini jack (L/R) and the SPEAKER (L/R) terminals according to the video input selection.

Installation and Connections

Power cord connection

English

Connect the power cord after all component connections have been completed.

1 Connect the power cord to this unit.

2 Plug the power cord into a power outlet.

CAUTION

÷ Use only the power cord provided. ÷ For the plasma display, a three-core power cord with a ground

terminal is used for efficiency protection. Always be sure to connect the power cord to a three-pronged grounded outlet and make sure that the cord is properly grounded. If you use a power source converter plug, use an outlet with a ground terminal and screw down the ground line.

NO!

Do not use a power supply voltage other than that indicated (AC 100 - 120 V, 50/60 Hz) as this may cause fire or electric shock.

Installation and Connections

How to route cables

Speed clamps and bead bands are included with this unit for bunching cables together. Once components are connected, follow the following steps to route cables.

English

* As viewed from the rear of the display.

Français

1 Organize cables together using the provided

speed clamps.

Insert 1 into an appropriate hole on the rear of the unit, then snap 2 into the back of 1 to fix the clamp.

Speed clamps are designed to be difficult to undo once in place. Please attach carefully.

To attach the speed clamps to the main unit

Connect the speed clamps using the 6 holes marked with “‡” below, depending on the situation.

2 Bunch separated cables together and secure them

with the provided bead bands.

Do not allow excessive stress to be placed on the ends of cables.

Note

Cables can be routed to the right or left.

Illustration depicts PDP-504CMX model.

* As viewed from the rear of the display.

Installation and Connections

To remove speed clamps

Using pliers, twist the clamp 90° and pull it outward. In some cases the clamp may have deteriorated over time and may get damaged when removed.

System Settings

Setting the onscreen display

English

language

The onscreen display language has been set to English as the factory default. To change to another language, the screen setting must be changed. Follow the procedures below to change the setting.

4 Use the 2/3 buttons to select [OPTION].

MENU INPUT1

PICTURE SCREEN SETUP OPTION

LANGUAGE ENGLISH

ENERGY SAVE SCREEN MGT. ORBITER OFF MASK CONTROL ON AUTO SET UP MODE INACTIVE AUTO FUNCTION OFF

AUDIO OUT FIXED

STANDARD

OFF : :

: : :

STANDBY/ ON

5/∞

2/3

SET

Main unit operating

Remote control unit

panel

1 Set the rear panel MAIN POWER switch to ON.

The STANDBY indicator on the front panel will light red.

2 Press the STANDBY/ON button to turn the power

ON.

The ON indicator on the front panel will light green.

3 Press the MENU button to display the menu

screen.

System Settings

MENU INPUT1

PICTURE SCREEN SETUP OPTION

CONTRAST

BRIGHTNESS R.LEVEL G.LEVEL B.LEVEL H.ENHANCE V.ENHANCE

PICTURE RESET

STANDBY/ ON

MENU 2/3

SET 5/∞

SET

ENTER

EXIT

5 Use the 5/∞ buttons to select [LANGUAGE], then

press the SET button.

FRANÇAIS

ITALIANO

ENGLISH

EXIT

2 3

23 2

ENGLISH

EXIT

ESPAÑOL

DEUTSCH

LANGUAGE

SET

Use the 2/3 buttons to select the desired language.

Each time the 2/3 buttons are pressed, the language alternates between those available, in the following order:

ENGLISH

3 2 3

LANGUAGE

SET

ENTER

EXIT

7 With the desired language displayed, press the

SET button.

The selected language will be set in memory, and the screen will return to that shown in step 4.

8 When settings are completed, press the MENU

button to return to the normal screen image.

Note

When the onscreen display language is set for either INPUT1 or INPUT2, the display language for the other input will be set to the same language.

Settings after connections

After components have been connected to INPUT1 or INPUT2, on-screen setup is necessary. Follow the procedure described below and make settings as they apply to the type of components connected.

System Settings

3 Use the 5/∞ buttons to select [SIGNAL FORMAT],

then press the SET button.

MENU INPUT1

PICTURE SCREEN SETUP OPTION

POWER MANAGEMENT CLAMP POSITION

SIGNAL FORMAT

OFF

AUTO

English

[SIGNAL FORMAT] setup

Note

These settings are required only when using the following input signal refresh rates: 1 31.5 kHz horizontal / 60 Hz vertical; 2

48.4 kHz horizontal / 60 Hz vertical, or 56.1 kHz horizontal / 70 Hz vertical; 3 64 kHz horizontal / 60 Hz vertical, 80 kHz horizontal / 75 Hz vertical, or 91.2 kHz horizontal / 85 Hz vertical. No manual setup is necessary for signals with other refresh rates, since adjustments are performed automatically (the [SIGNAL FORMAT] item will not be displayed).

5/∞

2/3

SET

Main unit operating panel

Remote control unit

MENU 2/3

SET 5/∞

4 Use the 2/3 buttons to select the display mode.

SIGNAL FORMAT

SET

1 When the input signal has a refresh rate of 31.5

kHz horizontal / 60 Hz vertical, pressing 2/3 will cause the display mode to change alternately as follows:

2 When the input signal has a refresh rate of 48.4

kHz horizontal / 60 Hz vertical, or 56.1 kHz horizontal / 70 Hz vertical, pressing 2/3 will cause the display mode to change alternately as follows:

3 PC AUTO 2

3 When the input signal has a refresh rate of 64 kHz

horizontal / 60 Hz vertical, 80 kHz horizontal / 75 Hz vertical, or 91.2 kHz horizontal / 85 Hz vertical, pressing 2/3 will cause the display mode to change alternately as follows:

3 SXGA 2 3 SXGA+ 2

3 VGA 2

3 WVGA 2

3 XGA 2

3 WXGA 2

VGA

EXIT

System Settings

1 Press the MENU button to display the menu

screen.

MENU INPUT1

PICTURE SCREEN SETUP OPTION

ENTER

EXIT

CONTRAST

BRIGHTNESS

R.LEVEL G.LEVEL B.LEVEL H.ENHANCE V.ENHANCE

PICTURE RESET

SET

2 Use the 2/3 buttons to select [SETUP].

MENU INPUT1

PICTURE SCREEN SETUP OPTION

POWER MANAGEMENT

CLAMP POSITION SIGNAL FORMAT

OFF

AUTO

If the [PC AUTO] setting is selected when using the above PC input signals, screen resolution will automatically switch between [XGA] and [WXGA].

Notes

÷ The [PC AUTO] setting supports automatic signal selection

only when using RGB separate SYNC inputs.

÷ When G ON SYNC or Composite SYNC signals are input,

selecting [PC AUTO] will cause the screen resolution to be set to [XGA] only.

÷ When using G ON SYNC or Composite SYNC with WXGA

inputs, set [SIGNAL FORMAT] manually to [WXGA].

5 Press the SET button.

The setting is stored in memory and the screen returns to that shown in step 3.

6 When the setup is completed, press the MENU

button to exit the menu screen.

Note

Make [SIGNAL FORMAT] setting for each input (INPUT1 and INPUT2).

System Settings

[CLAMP POSITION] setup

English

Depending on the signal, analog RGB signals may result in the screen image appearing with a whitish or greenish cast. In such cases, set [CLAMP POSITION] to [LOCKED]. Normally, leave this setting at [AUTO].

5/∞

2/3

SET

Main unit operating panel

1 Press the MENU button to display the menu

screen.

MENU INPUT1

PICTURE SCREEN SETUP OPTION

CONTRAST

BRIGHTNESS R.LEVEL G.LEVEL B.LEVEL H.ENHANCE V.ENHANCE

PICTURE RESET

Remote control unit

MENU 2/3

SET 5/∞

3 Use the 5/∞ buttons to select [CLAMP POSITION].

MENU INPUT1

PICTURE SCREEN SETUP OPTION

OFF

AUTO

POWER MANAGEMENT

CLAMP POSITION

SIGNAL FORMAT

SET

CHANGE EXIT

4 Press the SET button to select [LOCKED].

The factory default setting is [AUTO]. Mode selection will change as follows each time the SET button is pressed:

3 AUTO

LOCKED 2

5 When the setup is completed, press the MENU

button to exit the menu screen.

Notes

÷ The [CLAMP POSITION] setting is supported only for INPUT1. ÷ When making this setting, be sure to confirm the signal output

of the component used. For details, consult the component’s Operating Instructions.

System Settings

SET

ENTER

2 Use the 2/3 buttons to select [SETUP].

MENU INPUT1

PICTURE SCREEN SETUP OPTION

POWER MANAGEMENT

CLAMP POSITION

SIGNAL FORMAT

SET

CHANGE EXIT

OFF

AUTO

EXIT

Operation

Selecting input source

This section explains the basic operation of this unit. Outlined on the following pages is how to turn the main power on and off, put this unit in the operation or standby mode and how to select connected components.

Before you begin, make sure you have:

• Made connections between this unit and personal computer as described in the section “Installation and Connections” starting on page 10.

• Set up the on-screen menu to input signals from components connected to INPUT1 and INPUT2 as described in the section “System Settings” starting on page 16. If no connections are made to these terminals, on-screen setup is not necessary.

3 Press the INPUT button on the remote control unit

or the main unit to select the input.

Input changes each time the main unit’s INPUT button is pressed as follows:

3 INPUT1

INPUT2 2

• When the menu screen is displayed, changing the signal input will cause the menu screen to turn off.

• If the input computer signal is not supported by the display, the following message will be displayed:

INPUT1

CAUTION

UNSUPPORTED SIGNAL

: :

7816

HzfV .

588

512 684

HzfH .

English

STANDBY/ ON

INPUT

VOLUME [+/–]

Remote control unitMain unit operating

panel

STANDBY/ ON

INPUT

VOLUME [+/–]

1 Set the rear panel MAIN POWER switch to ON.

The STANDBY indicator on the front panel will light red.

2 Press the STANDBY/ON button to turn the power

ON.

The ON indicator on the front panel will light green.

FULL

INPUT1

CAUTION

OUT OF RANGE

––––

7715

HzfH .

HzfV .

020

FULL

4 Use VOLUME (+/–) buttons on the remote control

unit or the main unit to adjust the sound volume.

If no audio connections are made to this unit, this step is not necessary.

5 When viewing is finished, press the STANDBY/ON

button to put the unit in standby mode.

6 Set the rear panel MAIN POWER switch to OFF.

The STANDBY indicator may continue to light for a short while even after the main power is turned off. This is a result of residual electric load impressed on the circuitry, and the light will turn off presently.

Note

Please do not leave the same picture displayed on the screen for a long time. Doing so may cause a phenomenon known as “screen burn” which leaves a ghost, or residual, image of the picture on the screen.

Operation

Adjusting sound volume

English

VOLUME [+/–]

Remote control unit

Main unit operating panel

Press the VOLUME buttons.

Press the [–] or [+] button to respectively decrease and increase the volume of sound from the speakers.

VOLUME [+/–]

Confirming current status

DISPLAY

Main unit operating panel Remote control unit

Press the DISPLAY button.

The currently selected input, screen size and refresh rates will be displayed for about 3 seconds.

INPUT1

5VOLUME

Muting the sound

Operation

MUTING

Press the MUTING button on the remote control unit.

Press the MUTING button again to restore the sound. Muting is automatically canceled about 8 minutes after the button is pressed, and the volume level is adjusted to the minimum level. Press VOLUME + or VOLUME – to adjust the volume at a desired level.

: :

Notes

¶ The displayed refresh rates may be slightly different from

actual values.

¶ When using the Point zoom function (page 22) or Multiscreen

function (page 23), the position and input information for the enlarged screen area will be displayed.

¶ When the screen management function is active, the

[SCREEN MGT.] message will also be displayed at the lower left corner of the screen.

531

HzfV .

060

460 840

HzfH .

ODBYTDOT

Changing screen size

This unit incorporates screen modes of various height and width ratios. For optimal viewing, we recommend that you select the screen mode that best matches the video source that you are viewing. Although these modes are designed for full display of a picture on a wide screen, it is our hope that you make use of them with a full understanding of the manufacturer’s intentions.

Screen size selection

Operation

During personal computer signal input

1 DOT BY DOT

The input signal and the screen maintain a dot to line ratio of 1:1 and is thus highly faithful to the source.

[PDP-504CMX]

480 lines

768 lines

English

The size of the image displayed on the screen, and the range of the image shown can be set in one of four modes.

Press the SCREEN SIZE button to select the size.

SCREEN SIZE

Remote control unit

SCREEN SIZE

Main unit operating panel

The screen size changes each time the SCREEN SIZE button is pressed as follows.

[PDP-504CMX]

3 DOT BY DOT

FULL 2 4:3 2

3 PARTIAL

FULL 2 4:3 2

640 dots

1280 dots

(Illustration shows 640 x 480 input.)

[PDP-434CMX] * The PDP-434CMX is designed with horizontally

oblong elements, with the result that the image displayed will appear more oblong than the original input signal.

480 lines

640 dots

1024 dots

(Illustration shows 640 x 480 input.)

2 4:3

The display fills the screen as much as possible without altering the aspect ratio of the input signal.

768 lines

Operation

[PDP-434CMX]

3 DOT BY DOT 3 4:3

FULL 2

Consult the Computer signal compatibility table (pages 38 to 41) for information regarding screen sizes supported by each signal format.

Notes

÷ When the [PARTIAL], [ZOOM] or [FULL] setting is used to

display a non-wide screen 4:3 picture fully on a wide screen, a portion of the picture may be cut off or appear deformed.

÷ Be aware that when the display is used for commercial or

public viewing purposes, selecting the [PARTIAL], [ZOOM] or [FULL] mode settings may violate the rights of authors protected under copyright law.

÷ When [DOT BY DOT] or [4:3] screen size is selected, the

display position is moved slightly each time the power is turned on, in order to prevent image burning.

3 ZOOM

FULL 2 4:3 2

3 FULL

The display is presented with a widescreen aspect ratio of 16:9 and fills the entire screen.

Operation

4 PARTIAL (*Supported only on PDP-504CMX)

The [PARTIAL] setting is available only during personal

English

computer input (1280 x 1024 input only). The input signal and the screen maintain a dot to line ratio of 1:1. Display is highly faithful to the source. However, in order to maintain the 1:1 ratio, a portion of the display will not appear on the screen.

768 lines

Use the 5/∞ buttons to adjust the vertical position of the video image on the screen.

Enlarging one part of the screen (POINT ZOOM)

This plasma display allows enlarging of the screen image by ratios of [x 1.5], [x 2], and [x 3]. When enlarging the screen, the 5/∞/2/3 buttons can be used to move the enlarged viewing area around the screen. ¶ The range of zoom possible can be confirmed by viewing

the Zoom-Navi subscreen at the upper right of the main screen. The Zoom-Navi subscreen is displayed for about three seconds whenever the POINT ZOOM button, one of the 5/∞/2/3 buttons, or DISPLAY button is pressed.

1024 lines

5 ZOOM (*Supported only on PDP-434CMX)

The [ZOOM] setting is available only during personal computer input (1280 x 1024 input only). A portion of the display will not appear on the screen.

768 lines

Use the 5/∞ buttons to adjust the vertical position of the

Operation

video image on the screen.

Moving the screen position upward or downward

Press the 5/∞ buttons.

When playing a [PARTIAL] or [ZOOM] image (1280 x 1024 input only) from a computer, the vertical position of the screen image can be adjusted. This adjusted position cannot, however, be stored in memory.

Note

The image cannot be moved in the horizontal direction.

1024 lines

DISPLAY

POINT ZOOM

5/∞/2/3

1 Press the remote control unit’s POINT ZOOM

button.

x 1.5

Each time the POINT ZOOM button is pressed, the zoom ratio alternates in the following order:

3 OFF 3 x 1.5 3 x 2 3 x 3

66.0

SCROLL

R12

22.1

P.ZOOM

ZOOM

Zoom-Navi subscreen

Notes

¶ During use of the POINT ZOOM function, the screen size

cannot be changed.

¶ When using the plasma display in a profit-making activity, or

when exhibiting images publicly, using the screen size function to compress or stretch the image may result in infringement of the copyrights of the image owners.

Operation

2 Using the 5/∞/2/3 buttons, move the screen to

the desired part of the image.

x 1.5

SCROLL

R12

22.1

P.ZOOM

ZOOM

84.3

÷ Pressing the POINT ZOOM and 5/∞/2/3 buttons

again will change the zoom ratio and the position of screen enlarged.

÷ If the input signal changes, or if the menu screen is

displayed and the input is changed, or if the multiscreen mode is selected, the POINT ZOOM function will be canceled.

Multiscreen display

1 2-SCREEN

The main screen is displayed on the left and the subscreen on the right.

66.0

R12

22.1

English

2 PinP

The subscreen is displayed in one of the four corners of the main screen.

The plasma display’s multiscreen function allows the simultaneous display of two inputs. The multiscreen display include three modes, 2-SCREEN, PinP, and PoutP.

DISPLAY

SPLIT

SUB INPUT

PIP SHIFT

SWAP

1 Press the remote control unit’s SPLIT button.

Each time the button is pressed the multiscreen display changes in the following order:

3 2-SCREEN 3 PinP 3 PoutP 3 OFF

66.0

R12

22.1

3 PoutP

The subscreen is displayed outside the right side of the main screen.

66.0

R12

22.1

2 Press the remote control unit’s SUB INPUT button

to select the subscreen input source.

To exchange the main screen and subscreen inputs

Press the remote control unit’s SWAP button.

¶ When 2-SCREEN mode has been selected:

The right and left sides of the display will switch; what was previously the main screen will now show the subscreen, and vice versa.

¶ When PinP or PoutP has been selected:

What was previously the main screen image will now appear in reduced size as the subscreen image, and vice versa.

Operation

+ 66 hidden pages