Page 1
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2004
ORDER NO.
CRT3267
ND-BC1/E
UNIVERSAL REAR VIEW CAMERA
ND-BC1
/E
For details, refer to "Important symbols for good services".
K-ZZA. APR. 2004 printed in Japan
Page 2
1234
SAFETY INFORMATION
CAUTION
A
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely
complex products such as those covered by this manual.
repair
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the
warranty.
trying to do so
W
ARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the
state
B
Health & Safety Code Section 25249.6 - Proposition 65
- Service Precaution
1. You should conform to the regulations governing
the product (safety, radio and noise, and other
regulations), and should keep the safety during
servicing by following the safety instructions
described in this manual.
C
If you are not qualified to perform the repair of this product properly and safely, you should not risk
and refer the repair to a qualified service technician.
of California to cause cancer, birth defects or other reproductive harm.
[ Important symbols for good services ]
In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely.
When you find the procedures bearing any of the symbols, be sure to fulfill them:
1. Product safety
D
2. Adjustments
3. Cleaning
E
4. Shipping mode and shipping screws
5. Lubricants, glues, and replacement parts
You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and
should keep the safety during servicing by following the safety instructions described in this manual.
To keep the original performances of the product, optimum adjustments or specification confirmation is indispensable.
In accordance with the procedures or instructions described in this manual, adjustments should be performed.
For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleaning,
proper cleaning should be performed to restore their performances.
To protect the product from damages or failures that may be caused during transit, the shipping mode should be set or
the shipping screws should be installed before shipping out in accordance with this manual, if necessary.
Appropriately applying grease or glue can maintain the product performances. But improper lubrication or applying
glue may lead to failures or troubles in the product. By following the instructions in this manual, be sure to apply the
prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed
ones should be used.
F
2
1234
ND-BC1/E
Page 3
5678
SPECIFICATIONS
Power source .......................................... 14.4 V DC
(10.8 — 15.1 V allowable)
Grounding system .............................. Negative type
Max. current consumption .......................... 130 mA
Output video ........................................ Mirror image
(for rear view confirmation)
Sensor ............................ 1/4-inch color CCD sensor
No. of pixels ........ 491 (vertical) ⋅ 512 (horizontal)
(Effective no. of pixels roughly 250,000)
Lens ........................................................Wide-angle,
focal length f = 1.94 mm, F value 2.8
Angle of view .................... Horizontal: approx. 112º
Vertical: approx. 82º
Iris system .......................................... Electronic iris
Scanning system ........................................ Interlace
Synchronizing system ........ Internal synchronization
Signal-to-noise ratio .......................... 40 dB or more
(at the recommended intensity of illumination)
Horizontal resolution ............Approx. 300 TV lines
Illumination range .......... Approx. 1.5 — 100,000 lux
Image output ...................................... 1 Vp-p (75 Ω )
Operation temperature range .......... –30ºC — +65ºC
–22ºF — +149ºF
Storage temperature range .............. –40ºC — +80ºC
–40ºF — +176ºF
Dimensions
Camera unit .... 50 (W) × 25 (H) × 20.5 (D) mm
Power supply unit
.......................... 70 (W) × 35 (H) × 25 (D) mm
Weight
Camera unit ................................ 120 g (0.3 lbs)
Power supply .............................. 150 g (0.3 lbs)
Note:
Specifications and the design are subject to possible
modification without prior notice due to improvements.
2 (W) × 1 (H) × 3/4 (D) in.
2-3/4 (W) × 1-3/8 (H) × 1 (D) in.
(including the cable)
(including the power cord)
A
B
C
D
E
F
56
ND-BC1/E
7
8
3
Page 4
N
1234
EXPLODED VIEWS AND PARTS LIST
OTES : • Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List.
A
• Screw adjacent to mark on the product are used for disassembly.
• For the applying amount of lobricants or glue, follow the instructions in this manual.
"
(In the case of no amount instructions,apply as you think it appropriate.)
PACKING
B
C
D
PACKING SECTION PARTS LIST
Mark
No. Description Part No.
E
1 Cord CZD5393
2 Accessory Assy CZE5016
3 Attachment Assy CEA4582
* 4 Clamper CNV8262
* 5 Polyethylene Bag E36-615
* 6 Polyethylene Bag CZE5019
7 Double Sided Tape CZN7020
8 Packing CZN7021
9 Fastener CZN7022
10 Blister Pack CZH5368
F
11 Board CZH5370
12 Contain Box CZH5390
4
1234
ND-BC1/E
Mark
No. Description Part No.
13 Board CZH5389
14 Camera Assy CZX5105
15 Battery Box Assy CZX5106
16 Strap Assy CZX5107
17 Screw Assy(M3x4) CZE5017
* 18 Polyethylene Bag CZE5018
19 Strap CZN7018
20 Owner's Manual CZR5019
21 Owner's Manual CZR5021
Page 5
5678
Owner's Manual
Part No. Language
CZR5019 English, Spanish, German, French, Italian, Portuguese(B)
CZR5021 Traditional Chinese, Arabic
A
B
C
D
E
F
56
ND-BC1/E
7
8
5
Page 6
1234
OPERATIONS
A
2 Rear view camera
B
Connection sample
1 Power supply unit
2 Rear view camera
Video input jack
C
Connect to video input jack.
3 RCA cable
Accessory power supply
To electric terminal controlled by ignition
switch (12 V DC) ON/OFF.
4 Red
5 Fuse (1A)
Ground
To vehicle (metal) body.
6 Black
1 Power supply unit
3 RCA cable
5 Fuse (1A)
6 m (19 ft. 8 in.)
4 Red
6 m (19ft. 8 in.)
6 Black
D
1 Lock tie
E
Installation with a lock tie
When connecting the rear view camera and
the power supply unit, secure the cord to
the power supply unit with the lock tie.
1 Lock tie
F
6
1234
ND-BC1/E
Loading...