To ensure proper use, please read through this manual before using this product. It is
especially important that you read and observe WARNINGs and CAUTIONs in this manual.
Please keep the manual in a safe and accessible place for future reference.
Please read all of these instructions
regarding your display and retain them for
future reference.
1 Read this manual fully and carefully
before operating your display.
2 Keep this manual handy as a
reference for operating procedures
and safety information.
3 Pay close attention to all warnings
in this manual and follow the
instructions carefully.
4 Do not allow other persons to use
this system until they have read
and understood the operating
instructions.
5 Do not install the display where it
may (i) obstruct the driver’s vision,
(ii) impair the performance of any of
the vehicle’s operating systems or
safety features, including air bags,
hazard lamp buttons or (iii) impair
the driver’s ability to safely operate
the vehicle.
6 Do not operate this display if doing
so in any way will divert your
attention from the safe operation of
your vehicle. Always observe safe
driving rules and follow all existing
trafc regulations. If you experience
difficulty in operating the system
or reading the display, park your
vehicle in a safe location and make
necessary adjustments.
7 Please remember to fasten your
seat belt at all times while operating
your vehicle. If you are ever in
an accident, your injuries can be
considerably more severe if your
seat belt is not properly buckled.
8 Never use headphones while driving.
9 To promote safety, certain functions
are disabled unless the parking
brake is on, and the vehicle is not in
motion.
10 Never set the volume of your display
so high that you cannot hear outside
trafc and emergency vehicles.
WARNING
Do not attempt to install or service
your display by yourself. Installation
or servicing of the display by persons
without training and experience in
electronic equipment and automotive
accessories may be dangerous and
could expose you to the risk of electric
shock or other hazards.
To ensure safe driving
WARNING
• LIGHT GREEN LEAD AT POWER
CONNECTOR IS DESIGNED TO
DETECT PARKED STATUS AND
MUST BE CONNECTED TO THE
POWER SUPPLY SIDE OF THE
PARKING BRAKE SWITCH. IMPROPER
CONNECTION OR USE OF THIS LEAD
MAY VIOLATE APPLICABLE LAW AND
MAY RESULT IN SERIOUS INJURY OR
DAMAGE.
• To avoid the risk of damage and injury
and the potential violation of applicable
laws, this unit is not for use with video
that is visible to the driver.
• To avoid the risk of accident and the
potential violation of applicable laws, no
viewing of front seat video should ever
occur while the vehicle is being driven.
• In some countries or states the viewing
of images on a display inside a vehicle
even by persons other than the driver
may be illegal. Where such regulations
apply, they must be obeyed.
When you attempt to watch a video image
while driving, the warning "Viewing of front
seat video source while driving is strictly
prohibited." will appear on the front display.
To watch a video image on the front display,
park your vehicle in a safe place and apply
the parking brake.
When using the rear view camera
With an optional rear view camera, this unit
can be used as an aid to keep an eye on
trailers, or when backing into a tight parking
spot.
English
3
En
Section
01
Precautions
To avoid battery exhaustion
Keep the vehicle engine running when
using this unit to avoid draining the battery
power.
• When no power is supplied to this unit,
such as when the vehicle battery is
being replaced, the microcomputer of
this unit returns to its initial condition. We
recommend that you transcribe the audio
adjustment data.
WARNING
Do not use with vehicles that do not feature
an ACC position.
CAUTION: USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
CAUTION: THE USE OF OPTICAL
INSTRUMENTS WITH THIS PRODUCT
WILL INCREASE EYE HAZARD.
CAUTION
This product is a class 1 laser product
classified under the Safety of laser
products, IEC 60825-1:2007.
FCC STATEMENT
1. This device complies with Part 15 of the
FCC Rules.Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference.
(2) This device must accept any interference
received, including interferencethat may
causeundesired operation.
2. Changes or modifications not expressly
approved by the party responsible
forcompliance could void the user's
authority to operate the equipment.
NOTE: This equipment has been tested and
found to comply with the limits for aClass
B digital device, pursuant to Part 15 of
the FCC Rules. These limits aredesigned
to provide reasonable protection against
harmful interference in aresidential
installation.
This equipment generates uses and can
radiate radio frequency energy and,if not
installed and used in accordance with the
instructions, may causeharmful interference
to radio communications. However, there
is noguarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful interference
to radio or televisionreception, which can
bedetermined by turning the equipment
off and on, the user is encouraged to try
to correct the interference by one or more
ofthe following measures:
Reorient or relocate the receiving
antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet
on a circuit different from that towhich
the receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. This equipment should be
installed and operated with minimum
distance 20cm between the radiator & your
body
4
En
Before you start
Section
02
About this unit
CAUTION
• Do not allow this unit to come into
contact with liquids. Electrical shock
could result. Also, damage to this unit,
smoke, and overheating could result from
contact with liquids.
• Keep this manual handy for future
reference.
• Always keep the volume low enough to
hear outside sounds.
• Avoid exposure to moisture.
• If the battery is disconnected or
discharged, any preset memory will be
erased.
Note
Function setting operations are completed even if
the menu is cancelled before the operations are
conrmed.
In case of trouble
Should this product fail to operate properly,
please contact your dealer or nearest
authorized Pioneer Service Station.
Resetting the microprocessor
The microprocessor must be reset in the
following situations:
• Before using this unit for the first time
after installation
• If the unit fails to operate properly
• When strange or incorrect messages
appear on the display
Disable the demonstration mode
The demonstration mode should be turned
off as in the following process.
- Press the SRC key to turn on this unit.
- Press and hold the SEL key to display
Setting menu.
- Select General menu and then choose
Demo.
- Select Off and then press the center of
Multi Control to set the Demo mode off.
- Press the ESC key to deselect the
Setting menu.
The demonstration mode is also disabled
automatically by turning ignition key on and
off.
English
1 Press the (page 6, ) button on the top
right of the front panel to ip down it.
2 Press [RESET] with a pen tip or other
pointed instrument.
RESET
5
En
Section
03
Operating this unit
Press the [ ] button to ip down the front panel.
PartOperation
• Panel open
• Mute on/off
• Enter the source menu (2
sec.)
• Return to main source
menu (2 sec.), use [ ]
MUTE
6
En
(Left) / [ ] (Right) button
on the front panel or [ ] /
[ ] button on the remote
control to select the desired
mode, and press [M.C.]
button on the front panel
or [ENTER] button on the
remote control to conrm.
• Power off (2 sec.)
• Select playing mode:
• Radio
• Disc (when disc inserted)
• USB storage device/
iPod/iPhone (when USB
storage device/iPod/iPhone
connected)
• AUX-IN (front audio
& video input. External
SRC
peripheral devices with
RCA audio and video
outputs can be connected
with the unit.)
• AV Input (rear audio
& video input. External
peripheral devices with
RCA audio and video
outputs can be connected
with the unit.)
• BT
• APP
Operating this unit
Section
03
PartOperationPartOperation
BSM
BAND
(Left)
MULTI-
CONTROL
(M.C.)
(Down)
• Preset scan (in Radio
mode)
• Best Stations Memory (2
sec.) (in Radio mode)
• Stop playback
• Reject the incoming call
or hang up the current
conversation
• Play/Pause (in DVD, CD
and MP3/WMA modes)
• Band switch (in Radio
mode)
• Search the previous station
automatically (press more
than 2 seconds) (in Radio
mode).
• Search the previous station
manually (in Radio mode).
• Search the previous track
or chapter (in CD, MP3/
WMA, and DVD video
mode).
• Fast backward by 2, 4, 8,
16 step (2 sec.) (in CD,
MP3/WMA and DVD video
mode).
• Navigate left among option
items
• Adjust volume level (rotate).
• Conrm operation (press).
• Stop auto seeking (in Radio
mode) (press).
• Navigate down among
option items (in DVD, CD
and MP3/WMA modes)
• Play the previous preset
radio station (in Radio
RESET
• Cancel source select menu
and return to previous
menu
• When play back videos,
press to show information.
• Display off (press 2 sec.)
Press any button to
ESC
resume.
Music display
On BT main menu, press the
[ESC] button
to display the music interface,
press [ESC]
again to return the BT main
menu.
• Remote sensor
• AV in
AUX input jack (3.5mm
stereo/video jack)
Use to connect an auxiliary
device.
• USB port
• Navigate up among option
items (in DVD, CD and
(Up)
MP3/WMA modes)
• Play the next preset radio
station (in Radio mode)
• Audio/video Setting (press).
SEL
• Setting menu (press 2
sec.).
• 3.5 inch TFT display
• USB port
• Disc loading slot
• Eject button
• RESET
mode)
CAUTION
• Use an optional Pioneer USB cable (CD-U50E)
to connect the USB audio player/USB memory
as any device connected directly to the unit
will protrude out from the unit and may be
dangerous.
• Connect an optional iPod/iPhone (30-pin
connector) to the unit by iPod/iPhone cable
(CD-IU51).
Connect the USB port to the USB connector on
the front of the panel
• Connect an optional iPod/iPhone (Lightning
connector) to the unit by iPod/iPhone cable
(CD-IU52).
Connect the USB port to the USB connector on
the front of the panel
• Do not use unauthorized products.
(Right)
• Search the next station
automatically (press more
than 2 seconds) (in Radio
mode).
• Search the next station
manually (in Radio mode).
• Search the next track or
chapter (in CD, MP3/WMA,
and DVD video mode).
• Fast forward by 2, 4, 8,
16 step (2 sec.) (in CD,
MP3/WMA and DVD video
mode).
• Navigate right among
option items
English
7
En
Section
03
Operating this unit
A B
• Repeat A-B
• Fast forward
• Press to pause or resume
playback.
• Switch the HFP voice
between unit and HFP
device.
• Next track/chapter.
/
SEEK +
• Seek station by step.
• Seek the next available
station. (2 sec.)
• Display playback
DISP/
BSM
information.
• Radio preset scan / Radio
auto preset.
Part
SRC
ANGLE/
VIDEO
SUB
TITLE/
PHOTO
ZOOM
TITLE
ENTER
/
Operation
• Power on/off.
• Play source selection.
• Return to main source
menu (2 sec.).
• Select a difference angle/
version of the current DVD
scene.
• Show video list.
• Select DVD or DivX subtitle
language.
• Show photo list.
• Enlarge or reduce picture
or active image size.
• Enter DVD title menu.
• Menu cursor.
• Enter
• Connect or disconnect
HFP/A2DP. (press 2 sec.)
• Answer the incoming call.
• Dial out
• Press to stop playback.
• Reject the incoming call
or hang up the current
1-9
G / #
VOLUME
+/-
MUTE
AUDIO/
MUSIC
MENU/
PBC
ESC
SETUP
RDM
RPT
SEL
BAND
SEEK -
0 /
C /
• Digit buttons
• Goto search
• Input "#".
• Press to increase or
decrease volume.
• Press to mute. Press again
to unmute.
• Switch audio channel.
• Switch DVD audio language
• Show music list.
• Access DVD menu.
• Access PBC menu (for
VCD 2.0 or up)
• Exit the current menu, and
return to last menu.
• Enter setting menu.
• Enable/disable random
playback.
• Enable/disable repeat
playback.
• Enter audio/video setting
menu
• Fast reverse
• Select tuner band.
• Previous track/chapter.
• Press to seek the previous
/
station.
• Seek the previous available
station. (2 sec.)
• Input number "0".
• Input "+".
• Clear the input number.
• Input " ".
conversation.
8
En
Operating this unit
Section
03
Basic operations
Important
• Handle gently when removing or
attaching the front panel.
• Avoid subjecting the front panel to
excessive shock.
• Keep the front panel out of direct sunlight
and high temperatures.
• To avoid damaging the device or vehicle
interior, remove any cables and devices
attached to the front panel before
detaching it.
Removing the front panel to
protect your unit from theft
1 Press the (page 6, ) button to flip
down the front panel.
1
2 Grab the left side of the front panel, push
it to the right, then pull it out.
English
1
Make sure that the front panel has been
properly connected to the main unit.
2 Press the upper left end of the front
panel until it is rmly seated.
2
• If you can’t attach the front panel to the
main unit successfully, try again. Forcing
the front panel into place may result in
damage.
Turning the unit on
Press [SRC] button to turn the unit on.
Turning the unit off
Press and hold [SRC] until the unit turns
off.
2
* The indicator light ashes after the panel
removed.
3 Always keep the detached front panel in
a protection device such as a protection
case.
Re-attaching the front panel
1 Grab the left side of the front panel, push
it to the right, then push it in until it clicks.
Selecting a source
Press [SRC] to cycle between:
Radio (tuner)—Disc (when disc
inserted)—USB storage device/iPod/
iPhone (when USB storage device/
iPod/iPhone connected)—AUX (AUXIN cannot carry out a source selection,
unless it turns ON AUX by Setting
menu.)—AV Input (AV-IN cannot carry
out a source selection, unless it turns
ON AV Input by Setting menu. )—BT
(Bluetooth)—APP
Adjusting the volume
Turn [M.C.] to adjust the volume. Turn
counterclockwise to decrease and
clockwise to increase the volume.
En
9
Section
03
Operating this unit
Use and care of the remote
control
Using the remote control
Point the remote control in the direction of
the front panel to operate.
When using for the rst time, pull out the
lm protruding from the tray.
Replacing the battery
Slide the tray on the back of the remote
control out and insert the battery with
the plus (+) and minus (–) poles aligned
properly.
• When using for the rst time, pull out the
lm protruding from the tray.
CR2025(3V)
WARNING
• Keep the battery out of the reach of
children.
Should the battery be swallowed, consult
a doctor immediately.
• Batteries (battery pack or batteries
installed) must not be exposed to
excessive heat such as sunshine, re or
the like.
CAUTION
• Remove the battery if the remote control
is not used for a month or longer.
• There is a danger of explosion if the
battery is incorrectly replaced. Replace
only with the same or equivalent type.
• Do not handle the battery with metallic
tools.
• Do not store the battery with metallic
objects.
• If the battery leaks, wipe the remote
control completely clean and install a
new battery.
• When disposing of used batteries,
comply with governmental regulations or
environmental public institutions’ rules
that apply in your country/area.
Important
• Do not store the remote control in high
temperatures or direct sunlight.
• The remote control may not function
properly in direct sunlight.
• Do not let the remote control fall onto
the oor, where it may become jammed
under the brake or accelerator pedal.
Basic menu operations
Source (selecting a source)
1 Press and hold [SRC] button to display
the home menu.
2 Use [ ] (Left) / [ ] (Right) button on
the front panel or [ ] / [ ] button on
the remote control to select the desired
source.
Press [M.C.] button on the front panel or
[ENTER] button on the remote control to
select.
List (operating a list menu)
Press [ESC] to display the list menu (in
MP3/WMA/CD-DA mode) (page 12).
Audio/Video (setting an audio
menu)
Press [SEL] to display the audio/Video
menu.
Refer to Audio Adjustments (page 20).
System (setting a system menu)
Press and hold [SEL] more than 2 seconds
to display the system menu.
Refer to System settings (page 19).
10
En
Operating this unit
Section
03
Radio
Radio menu
Radio
POWERFUL
Source indicator
Time
Band
Preset station Number
Sound effect indicator
Frequency
Band selecting
Press [ BAND ] button repeatedly to
select desired band. The band indicator
(FM1, FM2, FM3 or AM) will be displayed.
Manual tuning (step by step)
Press the [ ] (Left) or [ ] (Right) button
to tune step by step.
Seeking
1 Press and hold the [ ] (Left) or [ ]
(Right) button more than 2 seconds to
seek previous/next available station.
2 You can cancel seek tuning by press
[M.C.] or [ ] (Left) / [ ] (Right) button.
Storing and recalling stations
You can easily store up to six stations for
each band as presets.
Storing a preset station manually
1 Tune to a desired station as above
method.
2 Press and hold [M.C.] button until the
preset station flashes on the screen,
press [ ] (Up) or [ ] (Down) button to
select a preset number, then press [M.C.]
button to store it.
You may also do the operation by the
remote control as following step:
Press and hold a number button (1-6) on
the remote control, the current station will
be stored in the memory.
Storing a preset station automatically
BSM (best stations memory) automatically
stores the 6 strongest stations of each
band, the unit can store 24 stations in total.
Best stations memory
1 Press and hold [ BSM] button more
than 2 seconds to search and store
stations. During searching and storing,
"BSM" appears on the display.
2 The unit will scan play the preset stations
automatically and "STATION" appears
on the display.
• To cancel, press [ BSM] button
again.
Recalling preset stations
Press [ BSM] button to scan play all
the preset stations.
LOC/DX (local / distant seek
tuning)
Local seek tuning lets you tune to only
those radio stations with sufciently strong
signals for good reception.
Distant seek tuning allows to receive all the
signals.
1 Press and hold the [SEL] button to
display the setting mode.
2 Press [ ] (Left) / [ ] (Right) button on
the front panel or [ ] / [ ] button on
the remote control to select Radio setting
menu.
3 Rotate the [M.C.] or press [ ] (Down)
button on the front panel or [ ] button
on the remote control to move the cursor
to LOC DX option.
4 Press [M.C.] or [ENTER] button to spread
the sub-menu.
5 Rotate the [M.C.] or press [ ] (Up) / [ ]
(Down) button on the front panel or [ ] /
[ ] button on the remote control to
select desired option.
6 Press [M.C.] or [ENTER] button to conrm.
En
English
11
Section
03
Operating this unit
USB playback
Playing les on a USB storage
device
1 Open the USB port cover.
2 Plug in the USB storage device using a
USB cable.
3 The unit will switch to USB mode
and load the files in the USB device
automatically.
Stopping playback of les on a
USB storage device
• Switch to other mode.
• Disconnect the USB storage device.
List menu
The unit will enter list menu after connecting
the USB storage, it will enter playing audio
files automatically after 15 seconds, press
[ESC] button to return to list menu.
Selecting a folder
1 Press [ ] (Up) / [ ] (Down) or [ ] / [ ]
button to select a folder (if there are
folders in the storage), press [M.C.] or
[ENTER] to conrm.
2 To nd a sub-folder, repeat above step.
Selecting a le (chapter)
In le list menu, press [ ] (Up) / [ ] (Down)
or [ ] / [ ] button to select a le, press
[M.C.] or [ENTER] button, the unit will load
the le and start playback.
Selecting a le of other folder:
1. If there are more than 1 folder in the
storage, a folder icon appears upon the
le’s names, press [ ] (Up) / [ ] (Down)
or [ ] / [ ] button to select it and press
[M.C.] or [ENTER] button to show all the
folders.
2. Press [ ] (Up) / [ ] (Down) or [ ] / [ ]
button to select a folder and press [M.C.]
or [ENTER] button to show the files in
the folder.
Playing audio les
Source indicator
Current track number/Total track
number
Time
Playback status indicator
Audio list indicator
Photo list indicator
Video list indicator
File list
Selecting le category
The unit will enter le list after loading the
storage, press [ ] (Left) button on the
front panel or [ ] button on the remote
control to return to le type selecting.
Press [ ] (Up) / [ ] (Down) button on the front
panel or [ ] / [ ] button on the remote
control to select file category (Audio, Photo,
Video), press [M.C.] or [ENTER] to conrm.
12
En
POWERFUL
Track information
Repeat and Random information
Sound effect indicator
Elapsed time/Total time of the track
• In playback menu, press [ESC] button to
return to upper category.
Play/Pause
Press [ BAND] button on the front
panel or [ ] button on the remote
control to play/pause.
Loading...
+ 28 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.