Pioneer IKT-UVL32UL-AG Users guide

Specifications

UVC

Bacterial Disinfection

• Input: AC 85-265V 50/60Hz

for Ductless Mini-Split Systems

• Output: DC 12V 8W

• PF > 0.5, Tc < 176 ºF

• LED Input: 6.72W

Owner’s Manual

Model Number: IKT-UVL32UL-AG

• Current: 0.56A

• Voltage: 12V

1491.54 mm

Applicable for These Air System Types

Wall-Mount

Floor-Ceiling

UVUVUV

DISINFECTION

SILENCE

ozoneozoneozone

FREE

SANITIZATION RECYCLE SAFETYCLEAN AIR

Cassette

Operation Principles & Technology

The Contents of UVC Mini

X-RAYS

VAU

UM-UV

ULTRAVIOLET

UV-C UV-B

UV-A

VISIBLE LIGHT

INFRARED

Improves indoor air quality and fights biological contamination inside mini splits.

UV LED Driver

RF Receiver (Optional)

100

200

280

315

RF Emitter (Optional)

400

700

LED UVC Strip

K

UVC Radiation used for disinfection is most effective at a wavelength of 254nm.

UVC

Scientific studies say:

Screw
Ring Connector (Optional)

The entire UV spectrum can wipe out or neutralize many microorganism
species, preventing them from replicating. UVC energy at 253.7 nanometers
provides the ideal germicidal effect. A combination of UVC + UVA is very

Adhesive Wire Base

1491.54 mm

Alcohol Wipe

effective at disinfection as well as odor removal.

DNA Structure

Mounting Pads

UVC

Warning Sticker

M

K

Wired Switch (Optional)

L

When exposing microorganisms to

Mini Kits

UVC light, the light penetrates through
their cell wall and disrupts the structure
of their DNA molecules, prohibiting
reproduction.

L

M

UV Shield Strip

CAUTION

UV LED LIGHT

Prolonged exposure to direct LED UV light

may be harmful to eyes & skin.

Manual

This unit is equipped with an LED UV light disinfection system.

Disconnect power before servicing.

Indirect exposure (blue glow) is not harmful

Keep in Mind

Prolonged exposure to direct LED UV Light

may be harmful to eyes & skin

Only qualified persons should install this product
Install only in accordance with the relevant building code

Indirect exposure (blue glow)

is not harmful

Read instructions carefully, including the safety warnings

Introduction to UVC Mini Kits

UVC MINI KITS are an innovative application of UV disinfection in Mini Splits

Air System Preparation Before Installation

and other space-limited systems.
It is normally used to disinfect an air conditioning system, by halting any

bio-growth on fan, coils and other surfaces, and related bad odors. It helps

1. Remove the cabinet cover

Disconnect Power Supply

Detach filters

substantially to maintain a clean, fresh air conditioner system, improve the
indoor air quality, extends life span, and reduces maintenance cost.

Dismantle the LED display assembly

Open the control box cover

Because space is tight and sufficient exposure of surfaces are required, the
UVC MINI KITS is best installed inside the supply vent with the light shining
onto the blower wheel (which is prone to contain concentrated mold growth).

2a. Detach drain pan to access
the area behind it.

UVC

1491.54 mm

2b. For systems with non-removable
drain pan, remove the louvers and
grills to access.

Cutaway View of Typical Installation of UVC MINI KITS in Mini Split

CAUTION UV LED LIGHT

3. Unless not required, drill a 2/3 hole
to pass connector cable to the back.

Prolonged exposure to direct LED UV light may be harmful to eyes & skin.

Disconnect power before servicing. Indirect exposure (blue glow) is not harmful.

(By the side of the control box)

IMPORTANT!

Install LED strip so that the light shines into the air system, not into the room.

IMPORTANT!

Disconnect the power supply before you do anything on the installation!

Mounting the UVC LED Strip

Install the Light Shield Strip

UVC light shield strip is designed by the manufacturer and recommended

1. Determine best location

Clean with cloth for any dust/dirt

to be installed with the UV LED strip. It is adhesive with a special material,
to shield these lights which may be exposed INTO THE ROOM.

Clean out with alcohol wipe

To install, simply peel off the paper
from the adhesive side and stick
firmly to the UV LED strip, with an
angle of 90°, upright.

2. If needed, cut the strip into the length
that best ts into the space. (Cut-to-length
instruction is provided in this manual)

3.Pass the connector cable through

1491.54 mm

Electric Installation Preparation

Remote Control

(Optional)

Wired Control

(Optional)

the drilled hole

UVC LED Strip

RF Emitter

3.Peel off paper from the adhesive
backing on the LED strip. Do this a
few at a time and press it down

Mini Split

RF Receiver

firmly onto the clean surfaces.

Note:
Remote and wired control cannot be used

Place the LED strip so the light will shine onto the blower wheel

Cut the strip only following the instructions by manufacturer

DON'T AIM THE UV LIGHT INTO THE ROOM

together

UV LED DRIVER

Red

Input: 85-265 V~

Blue

Output: 12 Vac, 2A

Electrical Installation

Electrical Installation

3. Tuck the power cable into the line chase

1. Remove the control box cover and
connect the UV LED Driver power cable
with the following:

on the back of the unit or place it under the
control box or other secure location.

UV LED DRIVER

Blue Wire: “L”
Red Wire: “N”

UV LED DRIVER

Notice: UVC MINI KIT comes with a wide voltage 85-265VAC power supply.

2a. Connect the UV LED DRIVER cable connector to the strip directly, only

a. Press once to
turn on/off

b. Long Press to

if the model is not equipped with either wired or remote controller.

LED Strip Cable

Driver Cable

change strength

1491.54 mm

Or

4. T urn on the power supply and confirm
that the UVC MINI KIT is working.

2b. If equipped with a wired control, connect the UV LED DRIVER cable to

Press once
to turn on/off

one end of the wired control, and the other end to the UV LED Strip.

Wired Control Cable

LED Strip Cable

Driver Cable

5. Apply the UV Warning Sticker to a proper location.

2c. If equipped with a wireless controller, connect the UV LED DRIVER cable
to one end of the RF receiver, and the other end to the UV LED Strip.

CAUTION

UV LED LIGHT

Prolonged exposure to direct LED UV light

Driver Cable

may be harmful to eyes & skin.

RF Receiver

This unit is equipped with an LED UV light disinfection system.

Disconnect power before servicing.

LED Strip Cable

Indirect exposure (blue glow) is not harmful

Cut-to-length Instruction

Bacterial Disinfection

EASY

Concepts to know

INSTALLA

for Ductless Mini-Split Systems

TION

UVC

One UV modular cycle is 10cm,
which includes UVC(1)+UVA(4)

Prevents bio-growth & related odors

Actual Length = air outlet vent length
which determines the required actual "L".

UV Module Design

on fan, coil and other interior surfaces!

Locate the best cutting point

First Cut Point(Most Recommended)

Closed Elec. Cycle

End with bushing

Benefits

Features

■ Prevent mold and bacteria growth

■ Ensure a clean mini-split system

■ Extend life of a mini split system

■ Super compact / High intensity

■ Easy fit with simple installation

■ 85-265 VAC wide range power supply

Cycle Point

1491.54 mm

■ Improve indoor air quality

■ Reduce maintenance cost

■ Cut-to-length LED strip design

■ Water resistance / Heat dissipation

■ 50,000 hours+ expected LED life

1. Determine how long you need to cut.
10 cm is a LED Modular Cycle.

Kits Include:

■ LED Strip (UVA/UVC)

■ Three years system warranty

■ Designed to fit major brands

■ For Wall-Mount, Floor-Ceiling & Cassette

■ Adhesive Sticker

2. Cut from the end without the cable!
Take off the bushing and prepare to cut.

■ LED Driver

■ Strip Cabinet

■ Bushing Block

■ Hardware

■ User Manual

■ Cleaning Cloth

3. Cut from the rst cut point
(two copper n) if >=10cm.If < 10cm,

cut at the second point.

4. Seal the end with the bushing,
tightly, make sure not to wrinkle
the inner LED strip circuit.

Parker Davis HVAC International, Inc.

3250 NW 107th Avenue
Doral, FL 33172
https://www.pdhvac.com

Factory Pre-Cut Services are not available at this time.

Phone: [phone]
Toll Free: [phone]