Pioneer FH-X500UI, FH-X70BT Owner's Manual

CD RDS RECEIVER AUTORADIO CD RDS REPRODUCTOR DE CD CON RECEPTOR RDS

FH-X70BT FH-X500UI

English EspañolFrançais

Owner’s Manual

Mode d’emploi

Manual de instrucciones

Section

Before you start

Thank you for purchasing this PIONEER product

To ensureproperuse,please read through this manual before using this product. It is especially important that you read and obser ve WARN-

INGs and CAUTIONs in this manual. Please keep the manual in a safe and accessible place for future reference.

FCC ID: AJDK054 MODEL NO.: FH-X70BT IC: 775E-K054 This device complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. The Bluetooth antenna cannot be removed (or replaced) by user. This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20 cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles).

MODEL NO.: FH-X500UI This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Information to User

Alteration or modifications carried out without appropriate authorization may invalidate the user ’s right to operate the equipment.

Note

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/ TV technician for help.

The Safety of Your Ears is in Your Hands

Get the most out of your equipment by playing it at a safe level—a level that lets the sound come through clearly without annoying blaring or distortion and, most importantly, without affecting your sensitive hearing. Sound can be deceiving. Over time, your hearing “comfort level” adapts to higher volumes of sound, so what sounds “normal” can actually be loud and harmful to your hearing. Guard against this by setting your equipment at a safe level BEFORE your hearing adapts.

ESTABLISH A SAFE LEVEL:

! Set your volume control at a low setting. ! Slowly increase the sound until you can hear

it comfortably and clearly, without distortion.

! Once you have established a comfortable

sound level, set the dial and leave it there.

BE SURE TO OBSERVE THE FOLLOWING GUIDELINES:

! Do not turn up the volume so high that you

can’t hear what’s around you.

! Use caution or temporarily discontinue use

in potentially hazardous situations.

! Do not use headphones while operating a

motorized vehicle; the use of headphones may create a traffic hazard and is illegal in many areas.

About this unit

The tuner frequencies on this unit are allocated for use in North America. Use in other areas may result in poor reception.

WARNING

Do not attempt to install or service this product by yourself. Installation or servicing of this product by persons without training and experience in electronic equipment and automotive accessories may be dangerous and could expose you to the risk of electric shock, injury or other hazards.

WARNING

Handling the cord on this product or cords associated with accessories sold with the product may expose you to chemicals listed on proposition 65 known to the State of California and other governmental entities to cause cancer and birth defect or other reproductive harm. Wash

hands after handling.

Before you start

Section

CAUTION: USE OF CONTROL OR ADJUSTMENT OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. CAUTION: THE USE OF OPTICAL INSTRUMENTS WITH THIS PRODUCT WILL INCREASE EYE HAZARD.

CAUTION

! Do not allow this unit to come into contact

with liquids. Electrical shock could result. Also, damage to this unit, smoke, and overheating could result from contact with liquids.

! Always keep the volume low enough to hear

outside sounds.

! Avoid exposure to moisture. ! If the battery is disconnected or discharged,

any preset memory will be erased.

CAUTION

This product is a class 1 laser product classified under the Safety of laser products, IEC 60825-1:2007.

Important (Serial number)

The serial number is located on the bottom of this unit. For your own security and convenience, be sure to record this number on the enclosed warranty card.

Note

Function setting operations are completed even if the menu is canceled before the operations are confirmed.

About this manual

! In the following instructions, USB memories

and USB audio players are collectively referred to as “USB storage device”.

! In this manual, iPod and iPhone will be re-

ferred to as “iPod”.

After-sales service for Pioneer products

Please contact the dealer or distributor from where you purchased this unit for after-sales service (including warranty conditions) or any other information. In case the necessary information is not available, please contact the companies listed below: Please do not ship your unit to the companies at the addresses listed below for repair without advance contact.

U.S.A.

Pioneer Electronics (USA) Inc. CUSTOMER SUPPORT DIVISION P.O. Box 1760 Long Beach, CA 90801-1760 800-421-1404

CANADA

Pioneer Electronics of Canada, Inc. CUSTOMER SATISFACTION DEPARTMENT 340 Ferrier Street Unit 2 Markham, Ontario L3R 2Z5, Canada 1-877-283-5901 905-479-4411

For warranty information please see the Limited Warranty sheet included with this unit.

In case of trouble

Should this unit fail to operate properly, please contact your dealer or nearest authorized PIONEER Service Station.

Visit our website

http://www.pioneerelectronics.com

in Canada

http://www.pioneerelectronics.ca

! Learn about product updates (such as firm-

ware updates) for your product.

! Register your product to receive notices

about product updates and to safeguard purchase details in our files in the event of loss or theft.

! Access owner ’s manuals, spare parts infor-

mation, service information, and much more.

English

8 9

7 a c6 b d

8 9

7 a c6 b d

8 a c

Section

Operating this unit

Head unit

FH-X70BT

FH-X500UI

1 h (eject) 8 c/d

3 1/

1 2 4 5

Part Part

FH-X70BT

(phone)

FH-X500UI MIX (MIXTRAX)

to 6/ a

MULTI-CONTROL

(M.C.)

(back)/

DIMMER

(dimmer)

Part Part

4 Disc loading slot b

5 DISP c

6 SRC/OFF d USB port

(iPod

BAND/

control)

CAUTION

! Use an optional Pioneer USB cable (CD-

U50E) to connect the USB storage device as any device connected directly to the unit will protrude out from the unit, which could be dangerous.

! Do not use unauthorized products.

(list)

AUX input jack (3.5 mm stereo jack)

Remote control

Remote controller buttons marked with the same numbers as on the unit operate in the same way as the corresponding unit button regardless of button name.

8 7 l k

f g h

i j

Part Operation

e VOLUME

f MUTE

g a/b

AUDIO

i DISP/SCRL

j e

FUNCTION

LIST/

ENTER

Press to increase or decrease volume.

Press to mute. Press again to unmute.

Press to recall preset stations. Press to select the next/previous folder.

FH-X70BT Press to end a call, reject an incoming call, or reject a call waiting while on another call.

FH-X500UI Press to select an audio function.

Press to select different displays. Press and hold to turn dimmer on or off.

Press to pause or resume playback.

FH-X70BT Press to start talking on the phone while operating a phone.

FH-X500UI Press to select functions.

Press to display the disc title, track title, folder, or file list depending on the source. Press to display the list depending on the source. While in the operating menu, press to control functions.

Display indication

Indicator State

Main infor-

mation section

(auto

answer)

(list)

Sub infor-

mation section

7 LOC Local seek tuning is on.

(sound re-

triever)

! Tuner: band and frequency ! CD player, USB storage de-

vice and iPod: elapsed playback time and text information

Appears when a lower tier of folder or menu exists.

Only for FH-X70BT

Shows when the automatic answering function is on.

Shows when 12H is selected under 12H/24H and CLOCK is selected under INFO DISPLAY.

The list function is being operated.

Sub information is displayed.

The sound retriever function is on.

Operating this unit

Section

Indicator State

Random play is on.

(ran-

The iPod source is selected and the shuffle or shuffle all function is on. The Pandora source is selected and the QuickMix is selected.

(re-

Track or folder repeat is on.

(iPod

This unit’s iPod function is operated from your iPod.

Only for FH-X70BT

Connected to a Bluetooth device. The line is on hold.

dom/shuffle/QuickMix)

peat)

control)

(Bluetooth indicator)

Set up menu

When you turn the ignition switch to ON after installation, set up menu appears on the display. You can set up the menu options below.

1 After installation of this unit, turn the ignition switch to ON. SET UP appears.

2 Turn M.C. to switch to YES.

# If you do not operate for 30 seconds, the set up menu will not be displayed. # If you prefer not to set up at this time, turn M.C. to switch to NO. Press to select. If you select NO, you cannot set up in the set up menu.

3 Press M.C. to select.

4 Complete the procedure outlined below to set the menu.

To proceed to the next menu option, you need to confirm your selection.

CLOCK SET (setting the clock)

1 Turn M.C. to adjust hour. 2 Press M.C. to select minute. 3 Turn M.C. to adjust minute. 4 Press M.C. to confirm the selection.

QUIT appears.

5 To finish your settings, turn M.C. to select YES.

# If you prefer to change your setting again, turn

M.C. to switch to NO. Press to select.

6 Press M.C. to select.

Notes

! You can set up the menu options from the

system menu. For details about the settings, refer to System menu on page 14.

! You can cancel set up menu by pressing

SRC/OFF.

Basic operations

Turning the unit on 1 Press SRC/OFF to turn the unit on.

Turning the unit off 1 Press and hold SRC/OFF until the unit turns

off.

Selecting a source

1 Press SRC/OFF to cycle between:

TUNER (tuner)—CD (CD player)—USB (USB)/ iPod (iPod)—PANDORA (Pandora)—AUX (AUX)—BT AUDIO (Bluetooth audio)

! BT AUDIO is not available for FH-X500UI.

Adjusting the volume 1 Turn M.C. to adjust the volume.

CAUTION

For safety reasons, park your vehicle when removing the front panel.

Note

When this unit’s blue/white lead is connected to the vehicle’s auto-antenna relay control terminal, the vehicle’s antenna extends when this unit’s source is turned on. To retract the antenna, turn the source off.

Use and care of the remote control

Using the remote control 1 Point the remote control in the direction of the

front panel to operate. When using for the first time, pull out the film protruding from the tray.

Replacing the battery 1 Slide the tray out on the back of the remote

control.

2 Insert the battery with the plus (+) and minus

(–) poles aligned properly.

WARNING

! Keep the battery out of the reach of children.

Should the battery be swallowed, consult a doctor immediately.

! Batteries (battery pack or batteries installed)

must not be exposed to excessive heat such as sunshine, fire or the like.

CAUTION

! Use one CR2025 (3 V) lithium battery. ! Remove the battery if the remote control is

not used for a month or longer.

! There is a danger of explosion if the battery is

incorrectly replaced. Replace only with the same or equivalent type.

! Do not handle the battery with metallic tools. ! Do not store the battery with metallic ob-

jects.

! If the battery leaks, wipe the remote control

completely clean and install a new battery.

! When disposing of used batteries, comply

with governmental regulations or environmental public institutions’ rules that apply in your country/area.

! “Perchlorate Material – special handling may

apply. See

www.dtsc.ca.gov/hazardouswaste/ perchlorate. (Applicable to California, U.S.A.)”

Important

! Do not store the remote control in high tem-

peratures or direct sunlight.

! The remote control may not function properly

in direct sunlight.

! Do not let the remote control fall onto the

floor, where it may become jammed under the brake or accelerator pedal.

English

Section

Operating this unit

Frequently used menu operations

Returning to the previous display Returning to the previous list (the folder one level higher)

/DIMMER.

1 Press

Returning to the ordinary display Canceling the main menu 1 Press BAND/

Returning to the ordinary display from the list 1 Press BAND/

Tuner

Basic operations

Selecting a band

1 Press BAND/

FM2, FM3 for FM or AM) is displayed.

Switching preset stations 1 Press c or d. ! Select PCH (preset channel) under SEEK to

use this function. For details about the settings, refer to SEEK (left/right key setting) on page 6.

! Use the a and b on the remote control to

switch between preset stations.

until the desired band (FM1,

Manual tuning (step by step) 1 Press c or d. ! Select MAN (manual tuning) under SEEK to

use this function. For details about the settings, refer to SEEK (left/right key setting) on page 6.

Seeking 1 Press and hold c or d, and then release.

You can cancel seek tuning by briefly pressing c or d. While pressing and holding c or d, you can skip stations. Seek tuning starts as soon as you release c or d.

Storing and recalling stations for each band

Using preset tuning buttons

1 When you find a station that you want to store in memory, press one of the preset tuning buttons (1/ the preset number stops flashing.

2 Press one of the preset tuning buttons (1/

to 6/ ) to select the desired station.

to 6/ ) and hold until

Switching the display

Selecting the desired text information 1 Press DISP to cycle between the following:

! BRDCST INFO (program service name/

song title/artist name)

! FREQUENCY (frequency) ! CLOCK (source name and clock)

Notes

! BRDCST INFO text information will change

automatically.

! Depending on the band, text information can

be changed.

! Text information items that can be changed

depend on the area.

Function settings

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select FUNCTION.

3 Turn M.C. to select the function.

Once selected, the following functions can be adjusted.

BSM (best stations memory)

BSM (best stations memory) automatically stores the six strongest stations in the order of their signal strength. 1 Press M.C. to turn BSM on.

To cancel, press M.C. again.

LOCAL (local seek tuning)

Local seek tuning lets you tune in to only those radio stations with sufficiently strong signals for good reception. 1 Press M.C. to select the desired setting.

FM: OFF—LV 1 —LV2 —LV3 —LV4 AM: OFF—LV 1 —LV2 The highest level setting allows reception of only the strongest stations, while lower levels allow the reception of weaker stations.

SEEK (left/right key setting)

You can assign a function to the left and right keys of the unit. Select MAN (manual tuning) to tune up or down manually or select PCH (preset channel) to switch between preset channels. 1 Press M.C. to select MAN or PCH.

CD/CD-R/CD-RW and USB storage devices

Basic operations

Playing a CD/CD-R/CD-RW 1 Insert the disc into the disc loading slot with

the label side up.

Ejecting a CD/CD-R/CD-RW 1 Press h.

Playing songs on a USB storage device

1 Open the USB port cover. 2 Plug in the USB storage device using a USB

cable. Playback is performed automatically.

Stopping playback of files on a USB storage device 1 Youmay disconnect the USB storage device at

any time. The unit stops playback.

Selecting a folder 1 Press 1/

Selecting a track 1 Press c or d.

Fast forwarding or reversing 1 Press and hold c or d. ! When playing compressed audio, there is no

Returning to root folder 1 Press and hold BAND/

Switching between compressed audio and CD-DA 1 Press BAND/

Switching between playback memory devices You can switch between playback memory devices on USB storage devices with more than one Mass Storage Device-compatible memory device. 1 Press BAND/ ! You can switch between up to 32 different

or 2/ .

sound during fast forward or reverse.

memory devices.

Operating this unit

Section

Note

Disconnect USB storage devices from the unit when not in use.

Operations using the MIXTRAX button

Turning MIXTRAX on or off You can use this function when USB is selected as the source. 1 FH-X70BT

Press 3/MIX to turn MIXTRAX on or off. FH-X500UI Press MIX to turn MIXTRAX on or off.

! For more details about MIXTRAX, refer to

About MIXTRAX on page 15.

! For more details about MIXTRAX functions,

refer to MIXTRAX menu on page 15.

! When MIXTRAX is in use, the sound retriever

function is disabled.

Switching the display

Selecting the desired text information 1 Press DISP to cycle between the following:

CD-DA

! ELAPSED TIME (track number and play-

back time)

! CLOCK (source name and clock) ! SPEANA (spectrum analyzer)

CD-TEXT

! TRACK INFO (track title/track artist/disc

title)

! ELAPSED TIME (track number and play-

back time)

! CLOCK (source name and clock) ! SPEANA (spectrum analyzer)

MP3/WMA/WAV

! TRACK INFO (track title/artist name/album

title)

! FILE INFO (file name/folder name) ! ELAPSED TIME (track number and play-

back time)

! CLOCK (source name and clock) ! SPEANA (spectrum analyzer)

Notes

! TRACK INFO and FILE INFO text information

will change automatically.

! Depending on the version of iTunes used to

write MP3 files to a disc or media file types, incompatible text stored within an audio file may be displayed incorrectly.

! Text information items that can be changed

depend on the media.

Selecting and playing files/ tracks from the name list

1 Press to switch to the file/track name list mode.

2 Use M.C. to select the desired file name (or folder name).

Selecting a file or folder 1 Turn M.C.

Playing 1 When a file or track is selected, press M.C.

Viewing a list of the files (or folders) in the selected folder 1 When a folder is selected, press M.C.

Playing a song in the selected folder 1 When a folder is selected, press and hold M.C.

Operations using special buttons

Selecting a repeat play range 1 Press 6/

Playing tracks in random order 1 Press 5/

! To change songs during random play, press d

to cycle between the following:

CD/CD-R/CD-RW

! ALL – Repeat all tracks ! ONE – Repeat the current track ! FLD – Repeat the current folder

USB storage device

! ALL – Repeat all files ! ONE – Repeat the current file ! FLD – Repeat the current folder

to turn random play on or off. Tracks in a selected repeat range are played in random order.

to switch to the next track. Pressing c restarts playback of the current track from the beginning of the song.

Pausing playback 1 Press 4/PAUSE to pause or resume.

Enhancing compressed audio and restoring rich sound (sound retriever)

Only for FH-X500UI

1 Press 3/S.Rtrv to cycle between:

1—2—OFF (off) 1 is effective for low compression rates, and 2

is effective for high compression rates.

! Key operation is disabled when MIXTRAX is

on.

Function settings

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select FUNCTION.

Once selected, the function below can be adjusted.

! S.RTRV is not available when MIXTRAX is

turned on.

S.RTRV (sound retriever)

Automatically enhances compressed audio and restores rich sound. 1 Press M.C. to select the desired setting.

For details, refer to Enhancing compressed

audio and restoring rich sound (sound retriever)

on page 7.

English

Section

Operating this unit

iPod

Basic operations

Playing songs on an iPod

1 Open the USB port cover. 2 Connect an iPod to the USB cable using an

iPod Dock Connector. Playback is performed automatically.

Selecting a song (chapter) 1 Press c or d.

Selecting an album 1 Press 1/

Fast forwarding or reversing 1 Press and hold c or d.

Notes

! The iPod cannot be turned on or off when the

! Disconnect headphones from the iPod be-

! The iPod will turn off about two minutes after

Operations using the MIXTRAX button

Turning MIXTRAX on or off 1 FH-X70BT

! For more details about MIXTRAX, refer to

! For more details about MIXTRAX functions,

or 2/ .

control mode is set to CONTROL AUDIO.

fore connecting it to this unit.

the ignition switch is set to OFF.

Press 3/MIX to turn MIXTRAX on or off. FH-X500UI Press MIX to turn MIXTRAX on or off.

About MIXTRAX on page 15.

refer to MIXTRAX menu on page 15.

Switching the display

Selecting the desired text information

1 Press DISP to cycle between the following:

CONTROL AUDIO/CONTROL iPod

! TRACK INFO (track title/artist name/album

title)

! ELAPSED TIME (track number and play-

back time)

! CLOCK (source name and clock) ! SPEANA (spectrum analyzer)

CONTROL APP

! CONTROL APP (APP MODE is displayed) ! CLOCK (source name and clock) ! SPEANA (spectrum analyzer)

Note

TRACK INFO text information will change automatically.

Browsing for a song

1 Press to switch to the top menu of list search.

2 Use M.C. to select a category/song.

Changing the name of the song or category 1 Turn M.C.

Playlists—artists—albums—songs—podcasts —genres—composers—audiobooks

Playing 1 When a song is selected, press M.C.

Viewing a list of songs in the selected category 1 When a category is selected, press M.C.

Playing a song in the selected category 1 When a category is selected, press and hold

M.C.

Searching the list by alphabet 1 When a list for the selected category is dis-

played, press mode. ! You also can switch to alphabet search

mode by turning M.C. twice.

2 Turn M.C. to select a letter. 3 Press M.C. to display the alphabetical list.

! To cancel searching, press

to switch to alphabet search

/DIMMER.

Notes

! You can play playlists created with the com-

puter application (MusicSphere). The application will be available on our website.

! Playlists that you created with the computer

application (MusicSphere) are displayed in abbreviated form.

Operations using special buttons

Selecting a repeat play range 1 Press 6/

! When the control mode is set to CONTROL

Selecting a random play range (shuffle) 1 Press 5/

to cycle between the following:

! ONE – Repeat the current song ! ALL – Repeat all songs in the selected list

iPod/CONTROL APP,the repeat play range will be same as what is set for the connected iPod.

to cycle between the following:

! SNG – Play back songs in the selected list

in random order.

! ALB – Play back songs from a randomly se-

lected album in order.

! OFF – Not play back in random order.

Playing all songs in random order (shuffle all) 1 Press and hold 5/ ! To turn off shuffle all, select OFF in shuffle. For

details, refer to Selecting a random play range (shuffle) on page 8.

Pausing playback 1 Press 4/PAUSE to pause or resume.

Enhancing compressed audio and restoring rich sound (sound retriever)

Only for FH-X500UI

1 Press 3/S.Rtrv to cycle between:

1—2—OFF (off) 1 is effective for low compression rates, and 2

is effective for high compression rates.

to turn shuffle all on.

Playing songs related to the currently playing song

You can play songs from the following lists.

• Album list of the currently playing artist

• Song list of the currently playing album

• Album list of the currently playing genre

1 Press and hold mode.

2 Turn M.C. to change the mode; press to select.

! ARTIST – Plays an album of the artist cur-

rently being played.

! ALBUM – Plays a song from the album cur-

rently being played.

! GENRE – Plays an album from the genre cur-

rently being played.

The selected song/album will be played after the currently playing song.

Notes

! The selected song/album may be canceled if

you operate functions other than link search (e.g. fast forward and reverse).

to switch to link play

Operating this unit

Section

! Depending on the song selected to play, the

end of the currently playing song and the beginning of the selected song/album may be cut off.

Operating this unit’s iPod function from your iPod

This unit's iPod function can be operated from a connected iPod. If you switch to APP Mode, you can have the sound from your iPod applications be output from your car's speakers. CONTROL iPod is not compatible with the following iPod models.

! iPod nano 1st generation ! iPod with video

CONTROL APP is compatible with the following iPod models.

! iPod touch 4th generation ! iPod touch 3rd generation ! iPod touch 2nd generation ! iPod touch 1st generation ! iPhone 4S ! iPhone 4 ! iPhone 3GS ! iPhone 3G ! iPhone

% Press BAND/

mode.

! CONTROL iPod – This unit’s iPod function

can be operated from the connected iPod.

! CONTROL APP – This unit’s iPod function

can be operated from the connected iPod. The unit will play back the sound from your iPod applications.

! CONTROL AUDIO – This unit’s iPod function

can be operated from this unit.

to switch the control

Notes

! Switching the control mode to

CONTROL iPod/CONTROL APP pauses song playback. Operate the iPod to resume playback.

! The following operations are still accessible

from the unit even if the control mode is set to CONTROL iPod/CONTROL APP.

— Pausing — Fast forward/reverse — Selecting a song (chapter)

! The volume can only be adjusted from this

unit.

Function settings

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select FUNCTION.

3 Turn M.C. to select the function.

Once selected, the following functions can be adjusted.

! AUDIO BOOK is not available when

CONTROL iPod/CONTROL APP is selected in

the control mode. For details, refer to Operating this unit’s iPod function from your iPod on

page 9.

AUDIO BOOK (audiobook speed)

1 Press M.C. to display the setting mode. 2 Turn M.C. to select your favorite setting.

! FASTER – Playback at a speed faster than

normal

! NORMAL – Playback at normal speed ! SLOWER – Playback at a speed slower

than normal

S.RTRV (sound retriever)

Automatically enhances compressed audio and restores rich sound. 1 Press M.C. to select the desired setting.

For details, refer to Enhancing compressed

audio and restoring rich sound (sound retriever)

on page 8.

Using Pandora

IMPORTANT:

Requirements to access Pandora using the Pioneer car audio/video products:

! iPhone compatibility

Apple iPhone (first generation), iPhone 3G, iPhone 3GS, iPhone 4, iPhone 4S, iPod touch 1G, iPod touch 2G, iPod touch 3G or iPod touch 4G (firmware version 3.0 or later) Certain firmware versions for the iPhone may not be compatible with the Pandora application. If this appears to be the case, please update the firmware to a version that is compatible with Pandora.

! Latest version of the Pandora application, down-

loaded to your device (Search Apple iTunes App Store for “Pandora”).

! Current Pandora account (if you do not have a

Pandora account, create one for free at http://www.pandora.com or with the mobile application.)

! Data Plan

Note: If the Data Plan for your iPhone does not provide for unlimited data usage, additional charges from your carrier may apply for accessing the Pandora service via 3G and/or EDGE networks.

! Connection to the Internet via 3G, EDGE or Wi-Fi

network.

! Optional Pioneer adapter cable connecting your

iPhone to the Pioneer car audio/video products.

Limitations:

! Access to the Pandora service will depend on the

availability of a cellular and/or Wi-Fi network for purposes of allowing your device to connect to the Internet.

! Ability of the Pioneer car audio/video products to

access the Pandora service is subject to change without notice and could be affected by any of the following: compatibility issues with future firmware versions of iPhone; compatibility issues with future firmware versions of the Pandora application for the iPhone; changes to the Pandora music service by Pandora; discontinuation of the Pandora music service by Pandora.

! Certain functions of the Pandora service are not

available when accessing the service through the Pioneer car audio/video products, including, but not limited to, creating new stations, deleting stations, emailing current stations, buying tracks from iTunes, viewing additional text information, logging in to Pandora, and adjusting Cell Network Audio Quality.

Pandora internet radio is a music service not affiliated with Pioneer. More information is available at http://www.pandora.com.

You can play Pandora by connecting your iPhone with the Pandora application installed.

Basic operations

Playing tracks 1 Connect an iPhone to the USB cable using an

iPhone Dock Connector.

2 Start up the Pandora application installed on

the iPhone.

Giving a Thumbs Up 1 Press 1/

to give a “Thumbs Up” for the track

currently playing.

English

Section

Operating this unit

Giving a Thumbs Down 1 Press 2/

Skipping tracks 1 Press d.

to give a “Thumbs Down” for the track currently playing and to skip to the next track.

Switching the display

Selecting the desired text information 1 Press DISP to cycle between the following:

! TRACK INFO (station name/track title/ar-

tist name/album title)

! ELAPSED TIME (playback time) ! CLOCK (source name and clock) ! SPEANA (spectrum analyzer)

Notes

! TRACK INFO text information will change au-

tomatically.

! Depending on the station, text information

can be changed.

Selecting and playing the QuickMix/station list

The device name that appears on the screen may not be the same as the device name of the connected device.

1 Press station list mode.

(list) to switch to the QuickMix/

2 Use M.C. to select the QuickMix or desired station.

Changing the sort order 1 Press

! ABC – You can sort the items in the list alpha-

! DATE – You can sort the items in the list in

Changing QuickMix or stations 1 Turn M.C.

Playing 1 When QuickMix or the station is selected,

(list).

betically

order of the dates on which the items were created

press M.C.

Operations using special buttons

Pausing playback 1 Press 4/PAUSE to pause or resume.

Function settings

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select FUNCTION.

3 Turn M.C. to select the function.

Once selected, the following functions can be adjusted.

BOOKMARK (bookmark)

1 Press M.C. to store track information.

S.RTRV (sound retriever)

Automatically enhances compressed audio and restores rich sound.

1 Press M.C. to select the desired setting.

1—2—OFF (off) 1 is effective for low compression rates, and 2

is effective for high compression rates.

Using Bluetooth wireless technology

Only for FH-X70BT

Using Bluetooth telephone

Important

! Since this unit is on standby to connect with

your cellular phone via Bluetooth wireless technology, using it without the engine running can drain the battery power.

! Operations may vary depending on the kind

of cellular phone.

! Advanced operations that require attention

such as dialing numbers on the monitor, using the phone book, etc., are prohibited while driving. Park your vehicle in a safe place when using these advanced operations.

! Be sure to park your vehicle in a safe place

and apply the parking brake when per forming this operation.

Setting up for hands-free phoning

Before you can use the hands-free phoning function you must set up the unit for use with your cellular phone.

1 Connection

Operate the Bluetooth telephone connection menu. Refer to Connection menu operation on page 11.

2 Function settings

Operate the Bluetooth telephone function menu. Refer to Phone menu operation on page

12.

Basic operations

Making a phone call 1 Refer to Phone menu operation on page 12.

Answering an incoming call 1 When a call is received, press

Ending a call 1 Press

Rejecting an incoming call 1 When a call is received, press and hold

Answering a call waiting 1 When a call is received, press

Switching between callers on hold 1 Press M.C.

Canceling call waiting 1 Press and hold

Adjusting the other party’s listening volume 1 Press c or d while talking on the phone. ! When private mode is on, this function is not

Turning private mode on or off 1 Press BAND/

available.

while talking on the phone.

Notes

! If private mode is selected on the cellular

phone, hands-free phoning may not be available.

Operating this unit

Section

! The estimated call time appears in the dis-

play (this may differ slightly from the actual call time).

Storing and recalling phone numbers

1 If you find a phone number that you want to store to memory, press and hold down one of the preset tuning buttons (1/ to 6/ ) to store it to the relevant preset tuning button.

The functions below can be used to store phone numbers to the memory. For details, refer to Phone menu operation on page 12.

! MISSED (missed call history) ! DIALED (dialed call history) ! RECEIVED (received call history) ! PHONE BOOK (phone book)

2 Press one of the preset tuning buttons

to 6/ ) to recall the desired phone

(1/ number.

3 Press M.C. to make a call.

Switching the display

Selecting the desired text information You can change the display during a call. 1 Press DISP to cycle between the following:

! Call time ! Name of other party ! Number of other party

Using voice recognition

This feature can be used on an iPod equipped with voice recognition that is connected by Bluetooth with the source set to iPod or BT AUDIO.

% Press and hold M.C. to switch to voice recognition mode.

The commands available with this unit are listed below.

! Song playback ! Making a phone call

Note

For details on voice recognition features, check the manual for the iPod you are using.

Connection menu operation

Important

! Be sure to park your vehicle in a safe place

and apply the parking brake when per forming this operation.

! Connected devices may not operate properly

if more than one Bluetooth device is connected at a time (e.g. a phone and a separate audio player are connected simultaneously).

1 Press and hold tion menu.

# You cannot operate this step during a call.

2 Turn M.C. to select the function.

Once selected, the following functions can be adjusted.

to display the connec-

DEVICELIST (connecting or disconnecting a de-

vice from the device list)

! When no device is selected in the device list,

this function is not available.

1 Press M.C. to display the setting mode. 2 Turn M.C. to select the name of a device you

want to connect/disconnect. ! Press and hold M.C. to switch the

Bluetooth device address and device name.

3 Press M.C. to connect/disconnect the selected

device. If the connection is established, * is indicated on the device name.

DEL DEVICE (deleting a device from the device list)

! When no device is selected in the device list,

this function is not available.

1 Press M.C. to display the setting mode. 2 Turn M.C. to select the name of a device you

want to delete. ! Press and hold M.C. to switch the

Bluetooth device address and device name.

3 Press M.C. to display DELETE YES. 4 Press M.C. to delete a device information from

the device list.

! While this function is in use, do not turn off

the engine.

ADD DEVICE (connecting a new device)

1 Press M.C. to start searching.

! To cancel, press M.C. while searching. ! If this unit fails to find any available cellular

phones, NOT FOUND is displayed.

2 Turn M.C. to select a device from the device

list. ! If the desired device is not displayed, select

RE-SEARCH.

! Press and hold M.C. to switch the

Bluetooth device address and device name.

3 Press M.C. to connect the selected device.

! To complete the connection, check the de-

vice name (Pioneer BT Unit) and enter the PIN code on your device.

! PIN code is set to 0000 as the default. You

can change this code.

! 6-digit number appears on the display of

this unit. Once the connection is established, this number disappears.

! If you are unable to complete the connec-

tion using this unit, use the device to connect to the unit.

! If three devices are already paired, DEVICE-

FULL is displayed and it is not possible to

perform this operation. In this case, delete a paired device first.

A. CONN (connecting to a Bluetooth device automatically)

1 Press M.C. to turn automatic connection on or

off.

VISIBLE (setting the visibility of this unit)

To check the availability of this unit from other devices, Bluetooth visibility of this unit can be turned on. 1 Press M.C. to turn the visibility of this unit on

or off.

PIN CODE (PIN code input)

English

Section

Operating this unit

To connect your device to this unit via Bluetooth wireless technology, you need to enter a PIN code on your device to verify the connection. The default code is 0000, but you can change it with this function.

1 Press M.C. to display the setting mode. 2 Turn M.C. to select a number. 3 Press M.C. to move the cursor to the next posi-

tion.

4 After inputting PIN code, press and hold M.C.

! After inputting, pressing M.C. returns you

to the PIN code input display, and you can change the PIN code.

DEV. INFO (Bluetooth device address display)

1 Press M.C. to display the setting mode. 2 Turn M.C. to display the device information.

Device name—Bluetooth device address

Phone menu operation

Important

Be sure to park your vehicle in a safe place and apply the parking brake when per forming this operation.

1 Press

2 Turn M.C. to select the function.

Once selected, the following functions can be adjusted.

MISSED (missed call history) DIALED (dialed call history) RECEIVED (received call history)

1 Press M.C. to display the phone number list. 2 Turn M.C. to select a name or phone number. 3 Press M.C. to make a call.

PHONE BOOK (phone book)

to display the phone menu.

! The phone book in your cellular phone will be

transferred automatically when the phone is connected to this unit.

! Depending on the cellular phone, the phone

book may not be transferred automatically. In this case, operate your cellular phone to transfer the phone book. The visibility of this unit should be on. Refer to VISIBLE (setting the visi- bility of this unit) on page 11.

1 Press M.C. to display SEARCH (alphabetical

list).

2 Turn M.C. to select the first letter of the name

you are looking for.

3 Press M.C. to display a registered name list. 4 Turn M.C. to select the name you are looking

for.

5 Press M.C. to display the phone number list. 6 Turn M.C. to select a phone number you want

to call.

7 Press M.C. to make a call.

PRESET1-6 (preset phone numbers)

1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired preset number. 3 Press M.C. to make a call.

! You can also use the preset number but-

PHONE FUNC (phone function)

You can set A. ANSR, R.TONE and PB INVT from this menu. For details, refer to Function and opera- tion on page 12.

to 6/ to recall a preset phone

tons 1/ number. For more details about storing phone numbers, refer to Storing and recalling phone numbers on page 11.

Function and operation

1 Display PHONE FUNC.

Refer to PHONE FUNC (phone function) on page

12.

2 Press M.C. to display the function menu.

3 Turn M.C. to select the function.

Once selected, the following functions can be adjusted.

A. ANSR (automatic answering)

1 Press M.C. to turn automatic answering on or

off.

R.TONE (ring tone select)

1 Press M.C. to turn the ring tone on or off.

PB INVT (phone book name view)

1 Press M.C. to invert the order of names in the

phone book.

Bluetooth Audio

Important

! Depending on the Bluetooth audio player

connected to this unit, the available operations will be limited to the following two levels:

— A2DP profile (Advanced Audio Distribution

Profile): You can only playback songs on your audio player. You cannot use the A2DP connection when iPod or PANDORA is selected as a source.

— AVRCP profile (Audio/Video Remote Control

Profile): You can perform playback, pause playback, select songs, etc.

! Since there are a number of Bluetooth audio

players available on the market, available operations will vary extensively. When operating your player with this unit, refer to the instruction manual that came with your Bluetooth audio player as well as this manual.

! As the signal from your cellular phone may

cause noise, avoid using it when you are listening to songs on your Bluetooth audio player.

! When a call is in progress on the cellular

phone connected to this unit via Bluetooth wireless technology, the sound of the Bluetooth audio player connected to this unit is muted.

! When the Bluetooth audio player is in use,

you cannot connect to a Bluetooth telephone automatically.

! Playback continues even if you switch from

your Bluetooth audio player to another source while listening to a song.

! Depending on the type of Bluetooth audio

player you have connected to this unit, operation and information display may not be available for some functions.

Setting up for Bluetooth audio

Before you can use the Bluetooth audio function you must set up the unit for use with your Bluetooth audio player. This entails establishing a Bluetooth wireless connection between this unit and your Bluetooth audio player, and pairing your Bluetooth audio player with this unit.

1 Connection

Operate the Bluetooth telephone connection menu. Refer to Connection menu operation on page 11.

Basic operations

Fast forwarding or reversing 1 Press and hold c or d.

Selecting a track 1 Press c or d.

Starting playback 1 Press BAND/

Operating this unit

Section

Switching the display

Selecting the desired text information 1 Press DISP to cycle between the following:

! DEVICE INFO (device name) ! TRACK INFO (track title/artist name/album

title)

! ELAPSED TIME (track number and play-

back time)

! CLOCK (source name and clock) ! SPEANA (spectrum analyzer)

Notes

! TRACK INFO text information will change au-

tomatically.

! Depending on the device, text information

can be changed.

Operations using special buttons

Selecting a repeat play range 1 Press 6/

Playing tracks in random order 1 Press 5/

Pausing playback 1 Press 4/PAUSE to pause or resume.

to select a repeat play range from one or all. ! This function may not be available depend-

ing on the type of Bluetooth audio player connected.

! The repeat play range varies depending on

the Bluetooth audio player in use.

to turn random play on or off.

! The random play range varies depending

on the Bluetooth audio player in use.

Function settings

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select FUNCTION.

3 Turn M.C. to select the function.

Once selected, the following functions can be adjusted.

PLAY (play)

1 Press M.C. to start playback.

STOP (stop)

1 Press M.C. to stop the playback.

S.RTRV (sound retriever)

Automatically enhances compressed audio and restores rich sound.

1 Press M.C. to select the desired setting.

1—2—OFF (off) 1 is effective for low compression rates, and 2

is effective for high compression rates.

Audio adjustments

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select AUDIO.

3 Turn M.C. to select the audio function.

Once selected, the following audio functions can be adjusted.

! FADER is not available when SUB.W/SUB.W

is selected in SP-P/O MODE. For details, refer to SP-P/O MODE (rear output and preout set- ting) on page 16.

! SUB.W and SUB.W CTRL are not available

when REAR/REAR is selected in

SP-P/O MODE. For details, refer to SP-P/O MODE (rear output and preout set-

ting) on page 16.

! SUB.W CTRL is not available when SUB.W is

selected in OFF. For details, refer to SUB.W (subwoofer on/off setting) on page 13.

FADER (fader adjustment)

1 Press M.C. to display the setting mode. 2 Turn M.C. to adjust the front/rear speaker bal-

ance.

BALANCE (balance adjustment)

1 Press M.C. to display the setting mode. 2 Turn M.C. to adjust the left/right speaker bal-

ance.

EQ SETTING (equalizer recall)

1 Press M.C. to display the setting mode. 2 Turn M.C. to select the equalizer.

POWERFUL—NATURAL—VOCAL—CUSTOM1—CUSTOM2—FLAT—SUPER BASS

The equalizer band and equalizer level can be customized when CUSTOM1 or CUSTOM2 is selected. If selecting CUSTOM1 or CUSTOM2, complete the procedures outlined below. If selecting other options, press M.C. to return to the previous display. ! CUSTOM1 can be set separately for each

source. However, USB, iPod and PANDORA are all set to the same setting automatically.

! CUSTOM2 is a shared setting used in com-

mon for all sources.

3 Press M.C. to display the setting mode. 4 Press M.C. to cycle between the following:

Equalizer band—Equalizer level

5 Turn M.C. to select the desired setting.

Equalizer band: 80HZ—250HZ—800HZ—

2.5KHZ—8KHZ Equalizer level: +6 to –6

LOUDNESS (loudness)

Loudness compensates for deficiencies in the lowfrequency and high-frequency ranges at low volume.

1 Press M.C. to select the desired setting.

OFF (off)—LOW (low)—MID (mid)—HI (high)

SUB.W (subwoofer on/off setting)

This unit is equipped with a subwoofer output which can be turned on or off.

1 Press M.C. to select the desired setting.

NOR (normal phase)—REV (reverse phase)— OFF (subwoofer off)

SUB.W CTRL (subwoofer adjustment)

Only frequencies lower than those in the selected range are outputted from the subwoofer.

1 Press M.C. to display the setting mode. 2 Press M.C. to cycle between the following:

Cut-off frequency—Output level—Slope level Rates that can be adjusted will flash.

3 Turn M.C. to select the desired setting.

Cut-off frequency: 50HZ—63HZ—80HZ—

100HZ—125HZ—160HZ—200HZ

Output level: –24 to +6 Slope level: –6— –12

BASS BOOST (bass boost)

1 Press M.C. to display the setting mode. 2 Turn M.C. to select a desired level.

0 to +6 is displayed as the level is increased or decreased.

HPF SETTING (high pass filter adjustment)

English

Section

Operating this unit

When you do not want low sounds from the subwoofer output frequency range to play from the front or rear speakers, turn on the HPF (high pass filter). Only frequencies higher than those in the selected range are output from the front or rear speakers.

1 Press M.C. to display the setting mode. 2 Press M.C. to cycle between the following:

Cut-off frequency—Slope level

3 Turn M.C. to select the desired setting.

Cut-off frequency: OFF—50HZ—63HZ—80HZ

—100HZ—125HZ—160HZ—200HZ

Slope level: –6— –12

SLA (source level adjustment)

SLA (Source level adjustment) lets you adjust the

volume level of each source to prevent radical changes in volume when switching between sources. ! Settings are based on the FM volume level,

which remains unchanged.

! The AM volume level can also be adjusted with

this function.

! When selecting FM as the source, you cannot

switch to SLA.

! USB, iPod and PANDORA are all set to the

same setting automatically.

1 Press M.C. to display the setting mode. 2 Turn M.C. to adjust the source volume.

Adjustment range: +4 to –4

System menu

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select SYSTEM.

3 Turn M.C. to select the system menu function.

Once selected, the following system menu functions can be adjusted.

! BT AUDIO, BT MEM CLEAR and

BT VERSION are not available for FH-X500UI.

CLOCK SET (setting the clock)

1 Press M.C. to display the setting mode. 2 Press M.C. to select the segment of the clock

display you wish to set. Hour—Minute

3 Turn M.C. to adjust the clock.

12H/24H (time notation)

1 Press M.C. to select the desired setting.

12H (12-hour clock)—24H (24-hour clock)

INFO DISPLAY (sub information)

The type of text information displayed in the sub information section can be toggled.

1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting.

SPEANA—LEVEL METER—SOURCE—CLOCK —OFF

! The signal bar indicator displays for SPEANA

or LEVEL METER when the source is set to

TUNER.

AUX (auxiliary input)

Activate this setting when using an auxiliary device connected to this unit.

1 Press M.C. to turn AUX on or off.

BT AUDIO (Bluetooth audio activation)

You need to activate the BT AUDIO source in order to use a Bluetooth audio player. 1 Press M.C. to turn the BT AUDIO source on or

off.

BT MEM CLEAR (clearing the Bluetooth device data stored on this unit)

Bluetooth device data stored on this unit can be cleared. To protect personal information, we recommend that you clear this data before transferring this unit to other persons. The following types of data on this unit will be cleared in such cases.

! Device list ! PIN code ! Call history ! Phone book ! Preset phone numbers

1 Press M.C. to show the confirmation display.

YES is displayed. Clearing memory is now on

standby. If you do not want to clear the Bluetooth device data stored on this unit, turn M.C. to display CANCEL and press it again to select.

2 Press M.C. to clear the memory.

CLEARED is displayed and the Bluetooth de-

vice data is cleared. ! While this function is in use, do not turn

off the engine.

BT VERSION (Bluetooth version display)

You can display the system versions of this unit and of Bluetooth module. 1 Press M.C. to display the information.

Selecting the key color

You can select desired colors for the keys of this unit.

1 Press M.C. to display the main menu.

2 Turn M.C. to display ILLUMI and press to select.

3 Turn M.C. to display KEY COLOR and press to select.

4 Turn M.C. to select the illumination color.

You can select any one of the options in the following list:

! Preset colors (ranging from WHITE to ROSE) ! SCAN (cycle through all colors) ! Sets of colors (WARM, AMBIENT, CALM) ! CUSTOM (customized illumination color)

Notes

! When SCAN is selected, the system auto-

matically cycles through the preset colors.

! When WARM is selected, the system auto-

matically cycles through the warm colors.

! When AMBIENT is selected, the system au-

tomatically cycles through the ambient colors.

! When CALM is selected, the system auto-

matically cycles through the calm colors.

! When CUSTOM is selected, the customized

color saved is selected.

Selecting the display color

You can select the desired colors for the display of this unit.

1 Press M.C. to display the main menu.

2 Turn M.C. to display ILLUMI and press to select.

3 Turn M.C. to display DISP COLOR and press to select.

4 Turn M.C. to select the illumination color.

You can select any one of the options in the following list:

! Preset colors (ranging from WHITE to ROSE) ! SCAN (cycle through all colors) ! Sets of colors (WARM, AMBIENT, CALM) ! CUSTOM (customized illumination color)

Operating this unit

Section

Note

For details about colors on the list, refer to Selecting the key color on page 14.

Selecting key and display color

You can select the desired colors for the keys and display of this unit.

1 Press M.C. to display the main menu.

2 Turn M.C. to display ILLUMI and press to select.

3 Turn M.C. to display BOTH COLOR and press to select.

4 Turn M.C. to select the illumination color.

You can select any one of the options in the following list:

! Preset colors (ranging from WHITE to ROSE) ! SCAN (cycle through all colors)

Notes

! Once you select a color in this function, col-

ors on the keys and display of this unit automatically switch to the color you selected.

! For details about colors on the list, refer to

Selecting the key color on page 14.

Selecting the key colors displayed when a call is received

Only for FH-X70BT

You can select the desired key colors to display when an incoming call is received.

1 Press M.C. to display the main menu.

2 Turn M.C. to display ILLUMI and press to select.

3 Turn M.C. to display PHONE COLOR and press to select.

4 Turn M.C. to select the illumination color.

You can select any one of the options in the following list:

! FLASHING – The color selected from

KEY COLOR flashes.

! FLASH MODE1 to FLASH MODE6 – The sys-

tem automatically cycles through all available key colors for this unit. Select the desired mode.

! OFF – No change in key color made when in-

coming calls are received.

Switching the dimmer setting

You can adjust the brightness of illumination.

1 Press M.C. to display the main menu.

2 Turn M.C. to display ILLUMI and press to select.

3 Turn M.C. to display DIMMER and press to select the desired setting. OFF (off)—ON (on)

! You can also change the dimmer setting by

pressing and holding

/DIMMER.

Customizing the illumination color

You can create custom illumination colors for both KEY COLOR and DISP COLOR.

1 Press M.C. to display the main menu.

2 Turn M.C. to display ILLUMI and press to select.

3 Turn M.C. to display KEY COLOR or DISP COLOR. Press to select.

4 Press M.C. and hold until the customizing illumination color setting appears in the display.

5 Press M.C. to select the primary color. R (red)—G (green)—B (blue)

6 Turn M.C. to adjust the brightness level. Adjustment range: 0 to 60

# You cannot select a level below 20 for all three of R (red), G (green), and B (blue) at the same time.

# You can also perform the same operation on other colors.

Note

You cannot create a custom illumination color while SCAN, WARM, AMBIENT or CALM is selected.

About MIXTRAX

MIXTRAX technology is used to insert a variety of sound effects in between songs, allowing you to experience your music as a nonstop mix complete with visual and lighting effects.

Notes

! Depending on the file/song, sound effects

may not be added.

! MIXTRAX includes a MIXTRAX flashing color

mode that when switched on turns the flashing colors on and off in time with the audio track. If you find the feature distracting while driving, please turn MIXTRAX off. Refer to Op- erations using the MIXTRAX button on page 7.

MIXTRAX menu

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select MIXTRAX.

3 Turn M.C. to select the MIXTRAX function.

Once selected, the following MIXTRAX functions can be adjusted. The function is enabled when MIXTRAX is on.

SHORT PLAYBACK (short playback mode)

You can select the length of the playback time.

1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting.

1.0 MIN (1.0 minute)—1.5 MIN (1.5 minutes)—

2.0 MIN (2.0 minutes)—2.5 MIN (2.5 minutes) —3.0 MIN (3.0 minutes)—OFF (off)

! Turn this option OFF if you want to play a selec-

tion all the way through from start to finish.

FLASH AREA (flash area)

You can select areas for flashing colors.

1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting.

KEY/DISPLAY (key and display)—KEY (key)— OFF (off)

! When OFF is selected, the color set under IL-

LUMI is used as the display color.

FLASH PATTERN (flash pattern)

English

Section

Operating this unit

You can select flashing color patterns.

1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting.

You can select any one of the options in the following list: ! SOUND LEVEL 1 to SOUND LEVEL 6 –

Flashing colors will flash on and off in synchronization with the sound level in a song. Select the desired mode.

! LOW PASS 1 to LOW PASS 6 – Flashing

colors will flash on and off in synchronization with the bass level in a song. Select the desired mode.

! RANDOM 1 – The pattern for the flashing

colors is randomly selected from the sound level mode and low pass mode.

! RANDOM 2 – The pattern for the flashing

colors is randomly selected from the sound level mode.

! RANDOM 3 – The pattern for the flashing

colors is randomly selected from the low pass mode.

DISPLAY FX (display effect)

The MIXTRAX special effects display can be turned on or off.

1 Press M.C. to select the desired setting.

ON (MIXTRAX special effects display)—OFF

(normal display)

CUT IN FX (manual cut-in effect)

You can turn on or off the MIXTRAX sound effects while manually changing tracks.

1 Press M.C. to select the desired setting.

ON (on)—OFF (off)

Initial menu

1 Press and hold SRC/OFF until the unit turns off.

2 Press and hold M.C. until the main menu appears in the display.

3 Turn M.C. to change the menu option and press to select INITIAL.

4 Turn M.C. to select the initial menu function.

Once selected, the following initial menu functions can be adjusted.

! S/W UPDATE is not available for FH-X500UI.

SP-P/O MODE (rear output and preout setting)

The rear speaker leads output and the RCA output of this unit can be used to connect a full-range speaker or subwoofer. Select a suitable option for your connection.

1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting.

You can select any one of the options in the following list: ! REAR/SUB.W – Select when there is a full-

range speaker connected to the rear speaker leads output and there is a subwoofer connected to the RCA output.

! SUB.W/SUB.W – Select when there is a

subwoofer connected directly to the rear speaker leads output without any auxiliary amp and there is a subwoofer connected to the RCA output.

! REAR/REAR – Select when there is a full-

range speaker connected to the rear speaker leads output and the RCA output. If there is a full-range speaker connected to the rear speaker leads output and the RCA output is not used, you may select either

REAR/SUB.W or REAR/REAR.

S/W UPDATE (updating the software)

This function is used to update this unit with the latest Bluetooth software. For about Bluetooth software and updating, refer to our website. ! Never turn the unit off while the Bluetooth soft-

ware is being updated.

1 Press M.C. to display the data transfer mode.

Follow the on-screen instructions to finish updating the Bluetooth software.

System menu

1 Press and hold SRC/OFF until the unit turns off.

2 Press and hold M.C. until the main menu appears in the display.

3 Turn M.C. to change the menu option and press to select SYSTEM.

4 Turn M.C. to select the system menu function.

For details, refer to System menu on page 14.

Using an AUX source

1 Insert the stereo mini plug into the AUX input jack.

2 Press SRC/OFF to select AUX as the source.

Note

AUX cannot be selected unless the auxiliary setting is turned on. For more details, refer to AUX (auxiliary input) on page 14.

Switching the display

Selecting the desired text information 1 Press DISP to cycle between the following:

! Source name ! Source name and clock

If an unwanted display appears

Turn off the unwanted display using the procedures listed below.

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select SYSTEM.

3 Turn M.C. to display DEMO OFF and press to select.

4 Turn M.C. to switch to YES.

5 Press M.C. to select.

6 78

Installation

Section

Connections

WARNING

! Use speakers over 50 W (output value) and

between 4 W to 8 W (impedance value). Do not use 1 W to 3 W speakers for this unit.

! The black cable is ground. When installing

this unit or power amp (sold separately), make sure to connect the ground wire first. Ensure that the ground wire is properly connected to metal parts of the car ’s body. The ground wire of the power amp and the one of this unit or any other device must be connected to the car separately with different screws. If the screw for the ground wire loosens or falls out, it could result in fire, generation of smoke or malfunction.

Ground wire

Other devices (Another electronic device in the car)

Important

! When installing this unit in a vehicle without

an ACC (accessory) position on the ignition switch, failure to connect the red cable to the terminal that detects operation of the ignition key may result in battery drain.

ACC position No ACC position

Metal parts of car’s body

POWER AMP

! Use this unit with a 12-volt battery and nega-

tive grounding only. Failure to do so may result in a fire or malfunction.

! To prevent a short-circuit, overheating or mal-

function, be sure to follow the directions below.

— Disconnect the negative terminal of the bat-

tery before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. Wrap adhesive tape around wiring that comes into contact with metal parts to protect the wiring.

— Place all cables away from moving parts,

such as the shift lever and seat rails.

— Place all cables away from hot places, such

as near the heater outlet.

— Do not connect the yellow cable to the battery

by passing it through the hole to the engine compartment.

— Cover any disconnected cable connectors

with insulating tape.

— Do not shorten any cables. — Never cut the insulation of the power cable of

this unit in order to share the power with other devices. The current capacity of the cable is limited.

— Use a fuse of the rating prescribed. — Never wire the negative speaker cable directly

to ground.

— Never band together negative cables of multi-

ple speakers.

! When this unit is on, control signals are sent

through the blue/white cable. Connect this cable to the system remote control of an external power amp or the vehicle’s auto-antenna relay control terminal (max. 300 mA 12 V DC). If the vehicle is equipped with a glass antenna, connect it to the antenna booster power supply terminal.

! Never connect the blue/white cable to the

power terminal of an external power amp. Also, never connect it to the power terminal of the auto antenna. Doing so may result in battery drain or a malfunction.

This unit

132

1 Power cord input 2 Microphone input (FH-X70BT only) 3 Microphone (FH-X70BT only)

4 m (13 ft. 1 in.)

4 Rear output or subwoofer output 5 Front output 6 Antenna input 7 Fuse (10 A) 8 Wired remote input

Hard-wired remote control adapter can be connected (sold separately).

Power cord

Perform these connections when not connecting a rear speaker lead to a subwoofer.











e f





c d



Perform these connections when using a subwoofer without the optional amplifier.









1 To power cord input 2 Left 3 Right 4 Front speaker 5 Rear speaker 6 White 7 White/black 8 Gray 9 Gray/black a Green b Green/black c Violet d Violet/black e Black (chassis ground)

Connect to a clean, paint-free metal location.

f Yellow

Connect to the constant 12 V supply terminal.

g Red

Connect to terminal controlled by ignition switch (12 V DC).

h Blue/white

Connect to system control terminal of the power amp or auto-antenna relay control terminal (max. 300 mA 12 V DC).

i Subwoofer (4 W)

c d

f g

k l













English

5cmcm

Section

Installation

j When using a subwoofer of 70 W (2 W), be

sure to connect the subwoofer to the violet and violet/black leads of this unit. Do not connect anything to the green and green/ black leads.

k Not used. l Subwoofer (4 W)×2

Notes

! With a 2 speaker system, do not connect any-

thing to the speaker leads that are not connected to speakers.

! Change the initial menu of this unit. Refer to

SP-P/O MODE (rear output and preout setting) on page 16.

The subwoofer output of this unit is monaural.

Power amp (sold separately)

Perform these connections when using the optional amplifier.



1 System remote control

Connect to Blue/white cable.

2 Power amp (sold separately) 3 Connect with RCA cables (sold separately) 4 To Front output 5 Front speaker 6 To Rear output or subwoofer output 7 Rear speaker or subwoofer



Installation

Important

! Check all connections and systems before

final installation.

! Do not use unauthorized parts as this may

cause malfunctions.

! Consult your dealer if installation requires

drilling of holes or other modifications to the vehicle.

! Do not install this unit where:

— it may interfere with operation of the vehicle. — it may cause injury to a passenger as a result

of a sudden stop.

! The semiconductor laser will be damaged if

it overheats. Install this unit away from hot places such as near the heater outlet.

! Optimum performance is obtained when the

unit is installed at an angle of less than 60°.

60°

! When installing, to ensure proper heat dis-

persal when using this unit, make sure you leave ample space behind the rear panel and wrap any loose cables so they are not blocking the vents.

Leave ample

5 cm

space

5 cm

! Use commercially available parts when in-

stalling.

Installation using the screw holes on the side of the unit

% Fastening the unit to the factory radiomounting bracket.

Position the unit so that its screw holes are aligned with the screw holes of the bracket, and tighten the screws at 3 locations on each side.

1 If the pawl gets in the way, bend it down. 2 Factory radio mounting bracket 3 Use either truss (5 mm × 8 mm) or flush sur-

face (5 mm × 9 mm) screws, depending on the bracket screw holes.

4 Dashboard or console

Installing the microphone

Only for FH-X70BT

CAUTION

It is extremely dangerous to allow the microphone lead to become wound around the steering column or shift lever. Be sure to install the unit in such a way that it will not obstruct driving.

Note

Install the microphone in a position and orientation that will enable it to pick up the voice of the person operating the system.

When installing the microphone on the sun visor

1 Fit the microphone lead into the groove.

1 Microphone lead 2 Groove

2 Install the microphone clip on the sun visor.

With the sun visor up, install the microphone clip. (Lowering the sun visor reduces the voice recognition rate.)

Installation

Additional information

Section

1 Microphone clip 2 Clamp

Use separately sold clamps to secure the lead where necessary inside the vehicle.

When installing the microphone on the steering column

1 Detach the microphone base from the microphone clip.

To detach the microphone base from the microphone clip, slide the microphone base.

1 Microphone 2 Microphone clip 3 Microphone base

2 Install the microphone on the steering column.

1 Double-sided tape 2 Install the microphone on the rear side of the

steering column.

3 Clamp

Use separately sold clamps to secure the lead where necessary inside the vehicle.

Adjusting the microphone angle

The microphone angle can be adjusted.

Troubleshooting

Symptom Cause Action

The display automatically returns to the ordinary display.

The repeat play range changes unexpectedly.

A subfolder is not played back.

NO XXXX appears when a display is changed (NO TITLE, for example).

The unit is malfunctioning. There is interference.

You did not perform any operation within about 30 seconds.

Depending on the repeat play range, the selected range may change when another folder or track is being selected or during fast forwarding/reversing.

Subfolders cannot be played when FLD (folder repeat) is selected.

There is no embedded text information.

You are using a device, such as a cellular phone, that transmits electric waves near the unit.

Perform operation again.

Select the repeat play range again.

Select another repeat play range.

Switch the display or play another track/file.

Move electrical devices that may be causing the interference away from the unit.

Symptom Cause Action

The sound from the Bluetooth audio source is not played back.

There is a call in progress on a Bluetooth connected cellular phone.

A Bluetooth connected cellular phone is currently being operated.

A call was made with a Bluetooth connected cellular phone and then immediately terminated. As a result, communication between this unit and the cellular phone was not terminated properly.

The sound will be played back when the call is terminated.

Do not operate the cellular phone at this time.

Reconnect the Bluetooth connection between this unit and the cellular phone.

Error messages

When you contact your dealer or your nearest Pioneer Service Center, be sure to note the error message.

English

Appendix

Additional information

Common

Message Cause Action

AMP ERROR Unit fails to op-

CD player

Message Cause Action

ERROR-07, 11, 12, 17, 30

ERROR-07, 10, 11, 12, 15, 17, 30, A0

ERROR-15 The inserted

ERROR-23 Unsupported

FORMAT READ

erate or speaker connection is incorrect; protective circuit is activated.

The disc is dirty. Clean the disc. The disc is

scratched. There is an elec-

trical or mechanical error.

disc is blank.

CD format. Sometimes

there is a delay between the start of playback and when you start to hear any sound.

Check the speaker connection. If the message fails to disappear even after the engine is switched off/on, contact your dealer or an authorized Pioneer Service Station for assistance.

Replace the disc.

Turn the ignition switch OFF and back ON, or switch to a different source, then back to the CD player.

Replace the disc.

Wait until the message disappears and you hear sound.

Message Cause Action

NO AUDIO The inserted

SKIPPED The inserted

PROTECT All the files on

USB storage device/iPod

Message Cause Action

FORMAT READ

NO AUDIO There are no

SKIPPED The connected

disc does not contain any playable files.

disc contains DRM protected files.

the inserted disc are embedded with DRM.

Sometimes there is a delay between the start of playback and when you start to hear any sound.

songs.

The connected USB storage device has security enabled.

USB storage device contains DRM protected files.

Replace the disc.

The protected files are skipped.

Replace the disc.

Wait until the message disappears and you hear sound.

Transfer the audio files to the USB storage device and connect.

Follow the USB storage device instructions to disable the security.

The protected files are skipped.

Message Cause Action

PROTECT All the files on

N/A USB The connected

CHECK USB The USB con-

CHECK USB The connected

the connected USB storage device are embedded with DRM.

USB device is not supported by this unit.

nector or USB cable has shortcircuited.

USB storage device consumes more than maximum allowable current.

Replace the USB storage device.

! Connect a USB Mass Storage Class compliant device. ! Disconnect your device and replace it with a compatible USB storage device.

Check that the USB connector or USB cable is not caught in something or damaged.

Disconnect the USB storage device and do not use it. Turn the ignition switch to OFF, then to ACC or ON and then connect only compliant USB storage devices.

Message Cause Action

CHECK USB The iPod oper-

ERROR-19 Communication

ERROR-23 USB storage de-

ates correctly but does not charge.

failed.

iPod failure. Disconnect the

vice was not formatted with FAT12, FAT16 or FAT32.

Make sure the connection cable for the iPod has not shorted out (e.g., not caught in metal objects). After checking, turn the ignition switch OFF and back ON, or disconnect the iPod and reconnect.

Perform one of the following operations. –Turn the ignition switch OFF and back ON. –Disconnect the USB storage device. –Change to a different source. Then, return to the USB source.

cable from the iPod. Once the iPod’s main menu is displayed, reconnect the iPod and reset it.

USB storage device should be formatted with FAT12, FAT16 or FAT32.

Additional information

Appendix

Additional information

Message Cause Action

ERROR-16 The iPod firm-

STOP There are no

NOT FOUND No related

Bluetooth device

Message Cause Action

ERROR-10 The power failed

ware version is old.

iPod failure. Disconnect the

songs in the current list.

songs.

for the Bluetooth module of this unit.

Update the iPod version.

cable from the iPod. Once the iPod’s main menu is displayed, reconnect the iPod and reset it.

Select a list that contains songs.

Transfer songs to the iPod.

Turn the ignition switch OFF and then to ACC or ON. If the error message is still displayed after performing the above action, please contact your dealer or an authorized Pioneer Service Station.

Pandora

Message Cause Action

ERROR-19 Communication

START UP APP

INOPERABLE The operation

TRY AGAIN Communica-

MAINTENANCE

SKIP LIMIT Skip limit

CHECK APP This version of

failed.

The Pandora application has not started running yet.

was disabled.

tions failed. Pandora system

is undergoing maintenance.

reached.

the Pandora application is not supported.

Disconnect the cable from the iPhone. Once the iPhone’s main menu is displayed, reconnect the iPhone and reset it.

Start up the Pandora application from your iPhone.

Run the same command for another track.

Try again later.

! Do not exceed the skip limit. ! Pandora limits the number of tracks you may skip per station and per day.

Connect an iPhone that has a compatible version of the Pandora application installed.

Message Cause Action

CHECK DEVICE

NO STATION No station

NO ACTIVESTNo station se-

Device error message displayed in Pandora Application. Unable to play music from Pandora.

found.

lected.

Please check your iPhone.

Create a station in the Pandora application on your iPhone.

Select a station.

Handling guidelines

Discs and player

Use only discs that feature either of the following two logos.

Use 12-cm discs. Do not use 8-cm discs or an adapter for 8-cm discs.

Use only conventional, fully circular discs. Do not use shaped discs.

Do not use cracked, chipped, warped, or otherwise damaged discs as they may damage the player.

Unfinalized CD-R/RW discs cannot be played back.

Do not touch the recorded surface of the discs.

Store discs in their cases when not in use.

Do not attach labels, write on or apply chemicals to the surface of the discs.

To clean a CD, wipe the disc with a soft cloth outward from the center.

Condensation may temporarily impair the player ’s performance. Let it rest for about one hour to adjust to a warmer temperature. Also, wipe any damp discs off with a soft cloth.

Playback of discs may not be possible because of disc characteristics, disc format, recorded application, playback environment, storage conditions, and so on.

Road shocks may interrupt disc playback.

Read the precautions for discs before using them.

When using discs that can be printed on label surfaces, check the instructions and the warnings of the discs. Depending on the discs, inserting and ejecting may not be possible. Using such discs may result in damage to this equipment.

Do not attach commercially available labels or other materials to the discs. ! The discs may warp making the disc unplay-

able.

! The labels may come off during playback and

prevent ejection of the discs, which may result in damage to the equipment.

English

Do not insert anything other than a CD into the CD loading slot.

Appendix

Additional information

USB storage device

Address any questions you have about your USB storage device to the manufacturer of the device.

Connections via USB hub are not supported.

Do not connect anything other than a USB storage device.

Firmly secure the USB storage device when driving. Do not let the USB storage device fall onto the floor, where it may become jammed under the brake or accelerator pedal.

Depending on the USB storage device, the following problems may occur.

! Operations may vary. ! The storage device may not be recognized. ! Files may not be played back properly. ! The device may generate noise in the radio.

iPod

Do not leave the iPod in places with high temperatures.

To ensure proper operation, connect the dock connector cable from the iPod directly to this unit.

Firmly secure the iPod when driving. Do not let the iPod fall onto the floor, where it may become jammed under the brake or accelerator pedal.

About iPod settings ! When an iPod is connected, this unit changes

the EQ (equalizer) setting of the iPod to off in order to optimize the acoustics. When you disconnect the iPod, the EQ returns to the original setting.

! You cannot set Repeat to off on the iPod when

using this unit. Repeat is automatically changed to All when the iPod is connected to this unit.

Incompatible text saved on the iPod will not be displayed by the unit.

DualDiscs

DualDiscs are two-sided discs that have a recordable CD for audio on one side and a recordable DVD for video on the other. Since the CD side of DualDiscs is not physically compatible with the general CD standard, it may not be possible to play the CD side with this unit. Frequent loading and ejecting of a DualDisc may result in scratches on the disc. Serious scratches can lead to playback problems on this unit. In some cases, a DualDisc may become stuck in the disc loading slot and will not eject. To prevent this, we recommend you refrain from using DualDisc with this unit. Please refer to the information from the disc manufacturer for more detailed information about DualDiscs.

Compressed audio compatibility (disc, USB)

WMA

File extension: .wma

Bit rate: 48 kbps to 320 kbps (CBR), 48 kbps to 384 kbps (VBR)

Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz

Windows Media Audio Professional, Lossless, Voice/DRM Stream/Stream with video: Not compatible

MP3

File extension: .mp3

Bit rate: 8 kbps to 320 kbps (CBR), VBR

Sampling frequency: 8 kHz to 48 kHz (32 kHz,

44.1 kHz, 48 kHz for emphasis)

Compatible ID3 tag version: 1.0, 1.1, 2.2, 2.3, 2.4 (ID3 tag Version 2.x is given priority over Version

1.x.)

M3u playlist: Not compatible

MP3i (MP3 interactive), mp3 PRO: Not compatible

WAV

File extension: .wav

Quantization bits: 8 and 16 (LPCM), 4 (MS ADPCM)

Sampling frequency: 16 kHz to 48 kHz (LPCM),

22.05 kHz and 44.1 kHz (MS ADPCM)

Supplemental information

Only the first 32 characters can be displayed as a file name (including the file extension) or a folder name.

This unit may not operate correctly depending on the application used to encode WMA files.

There may be a slight delay at the start of playback of audio files embedded with image data or audio files stored on a USB storage device that has numerous folder hierarchies.

Disc

Playable folder hierarchy: up to eight tiers (A practical hierarchy is less than two tiers.)

Playable folders: up to 99

Playable files: up to 999

File system: ISO 9660 Level 1 and 2, Romeo, Joliet

Multi-session playback: Compatible

Packet write data transfer: Not compatible

Regardless of the length of blank sections between the songs from the original recording, compressed audio discs play with a short pause between songs.

USB storage device

Playable folder hierarchy: up to eight tiers (A practical hierarchy is less than two tiers.)

Playable folders: up to 500

Playable files: up to 15 000

Playback of copyright-protected files: Not compatible

Partitioned USB storage device: Only the first partition can be played.

There may be a slight delay when starting playback of audio files on a USB storage device with numerous folder hierarchies.

CAUTION

! Pioneer cannot guarantee compatibility with

all USB mass storage devices and assumes no responsibility for any loss of data on media players, smart phones, or other devices while using this product.

! Do not leave discs or a USB storage device

in any place that is subject to high temperatures.

iPod compatibility

This unit supports only the following iPod models. Supported iPod software versions are shown below. Older versions may not be supported. Made for ! iPod touch 4th generation (software version

5.1.1)

Additional information

Appendix

Additional information

! iPod touch 3rd generation (software version

5.1.1)

! iPod touch 2nd generation (software version

4.2.1)

! iPod touch 1st generation (software version

3.1.3)

! iPod classic 160GB (software version 2.0.4) ! iPod classic 120GB (software version 2.0.1) ! iPod classic (software version 1.1.2) ! iPod with video (software version 1.3.0) ! iPod nano 6th generation (software version

1.2)

! iPod nano 5th generation (software version

1.0.2)

! iPod nano 4th generation (software version

1.0.4)

! iPod nano 3rd generation (software version

1.1.3)

! iPod nano 2nd generation (software version

1.1.3)

! iPod nano 1st generation (software version

1.3.1)

! iPhone 4S (software version 5.1.1) ! iPhone 4 (software version 5.1.1) ! iPhone 3GS (software version 5.1.1) ! iPhone 3G (software version 4.2.1) ! iPhone (software version 3.1.2)

Depending on the generation or version of the iPod, some functions may not be available.

Operations may vary depending on the software version of iPod.

When using an iPod, an iPod Dock Connector to USB Cable is required.

A Pioneer CD-IU51 interface cable is also available. For details, consult your dealer.

About the file/format compatibility, refer to the iPod manuals.

Audiobook, Podcast: Compatible

CAUTION

Pioneer accepts no responsibility for data lost on the iPod, even if that data is lost while this unit is used.

Sequence of audio files

The user cannot assign folder numbers and specify playback sequences with this unit.

Example of a hierarchy

 

 

Level 1 Level 2 Level 3 Level 4

Disc

Folder selection sequence or other operation may differ depending on the encoding or writing software.

USB storage device

Playback sequence is the same as recorded sequence in the USB storage device. To specify the playback sequence, the following method is recommended. 1 Create a file name that includes numbers

that specify the playback sequence (e.g., 001xxx.mp3 and 099yyy.mp3).

2 Put those files into a folder. 3 Save the folder containing files on the USB

storage device. However,depending on the system environment, you may not be able to specify the playback sequence.



audio file



01 to 05: Folder number 1 to 6: Playback sequence

: Folder

: Compressed

For USB portable audio players, the sequence is different and depends on the player.

Bluetooth profiles

In order to use Bluetooth wireless technology, devices must be able to interpret certain profiles. This unit is compatible with the following profiles.

! GAP (Generic Access Profile) ! OPP (Object Push Profile) ! HFP (Hands Free Profile) 1.5 ! HSP (Head Set Profile) ! PBAP (Phone Book Access Profile) ! A2DP (Advanced Audio Distribution Profile) ! AVRCP (Audio/Video Remote Control Profile)

1.3

Bluetooth

The Bluetoothâword mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by PIONEER CORPORATION is under license. Other trademarks and trade names are those of their respective owners.

iTunes

Apple and iTunes are trademarks of Apple Inc., registered in the U.S. and other countries.

MP3

Supply of this product only conveys a license for private, non-commercial use and does not convey a license nor imply any right to use this product in any commercial (i.e. revenue-generating) real time broadcasting (terrestrial, satellite, cable and/or any other media), broadcasting/

streaming via internet, intranets and/or other networks or in other electronic content distribution systems, such as pay-audio or audio-on-demand applications. An independent license for such use is required. For details, please visit http://www.mp3licensing.com.

WMA

Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product includes technology owned by Microsoft Corporation and cannot be used or distributed without a license from Microsoft Licensing, Inc.

iPod & iPhone

iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. “Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulator y standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance.

Pandora®internet radio

PANDORA, the PANDORA logo, and the Pandora trade dress are trademarks or registered trademarks of Pandora Media, Inc. Used with permission.

MIXTRAX

MIXTRAX is a trademark of the PIONEER CORPORATION.

English

Appendix

Additional information

Specifications

General

Power source ................... 14.4 V DC (10.8 V to 15.1 V al-

Grounding system ............ Negative type

Maximum current consumption

................................... 10.0 A

Dimensions (W × H × D):

Chassis .............. 178 mm × 100 mm ×

Nose .................. 170mm × 96mm ×

Weight ............................. 1.2 kg (2.6 lbs)

Audio

Maximum power output ... 50 W × 4

Continuous power output

................................... 22 W × 4 (50 Hz to 15000 Hz,

Load impedance .............. 4 W (4 W to 8 W allowable)

Preout maximum output level

................................... 2.0 V

Loudness contour ............ +10dB (100 Hz), +6.5 dB

Equalizer (5-Band Graphic Equalizer):

Frequency ................. 80 Hz/250 Hz/800 Hz/

Equalization range .... ±12 dB (2 dB step)

Subwoofer (mono):

Frequency ................. 50 Hz/63 Hz/80 Hz/100 Hz/

Slope ........................ –6 dB/oct, –12 dB/oct

Gain ......................... +6dB to –24 dB

Phase ....................... Normal/Reverse

CD player

System ............................ Compact disc audio system

Usable discs .................... Compact disc

Signal-to-noise ratio ......... 94 dB (1 kHz) (IHF-A network)

Number of channels ........ 2 (stereo)

MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3

WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch

lowable)

165 mm (7 in.× 3-7/8 in.× 6-1/2 in.)

17 mm (6-3/4 in.× 3-3/4 in.× 5/8 in.)

70 W × 1/2 W (for subwoofer)

5 % THD, 4 W load, both channels driven)

(10 kHz) (volume: –30 dB)

2.5 kHz/8 kHz

125 Hz/160 Hz/200 Hz

audio) (Windows Media Player)

WAV signal format ........... Linear PCM & MS ADPCM

USB

USB standard specification

................................... USB 2.0 full speed

Maximum current supply

................................... 1 A

USB Class ....................... MSC (Mass Storage Class)

File system ....................... FAT12, FAT16, FAT32

MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3

WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch

WAV signal format ........... Linear PCM & MS ADPCM

FM tuner

Frequency range .............. 87.9 MHz to 107.9 MHz

Usable sensitivity ............. 9 dBf (0.8 µV/75 W, mono, S/N:

Signal-to-noise ratio ......... 72 dB (IHF-A network)

AM tuner

Frequency range .............. 530 kHz to 1 710 kHz

Usable sensitivity ............. 25 µV (S/N: 20 dB)

Signal-to-noise ratio ......... 62 dB (IHF-A network)

Bluetooth (FH-X70BT only)

Version ............................ Bluetooth 3.0 certified

Output power ................... +4 dBm Maximum

(Non-compressed)

audio) (Windows Media Player)

(Non-compressed)

30 dB)

(Power class 2)

CEA2006 Specifications

Power output ................... 14 W RMS × 4 Channels (4 W

S/N ratio .......................... 91 dBA (reference: 1 W into

and ≦ 1 % THD+N)

4 W)

Note

Specifications and the design are subject to modifications without notice.

+ 56 hidden pages