Pioneer DJS-1000 User Manual

DJ SAMPLER

DJS-1000

pioneerdj.com/support/

For FAQs and other support information for this product, visit the above site.

Operating Instructions (Quick Start Guide)

IMPORTANT

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

NOTE

THE NO USER-SERVICEABLE PARTS COMPARTMENT WARNING IS LOCATED ON THE APPLIANCE BOTTOM.

The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.

D3-4-2-1-1b_A1_En

D3-7-13-68_A1_En

IMPORTANT

ATTENTION

DANGER D´ELECTROCUTION

NE PAS OUVRIR

Ce symbole de l’éclair, placé dans un
triangle équilatéral, a pour but d’attirer
l’attention de l’utilisateur sur la présence, à
l’intérieur du coffret de l’appareil, de
“tensions dangereuses” non isolées d’une
grandeur suffisante pour représenter un
risque d’électrocution pour les êtres
humains.

ATTENTION :

POUR ÉVITER TOUT RISQUE
D’ÉLECTROCUTION, NE PAS ENLEVER LE
COUVERCLE (NI LE PANNEAU ARRIÈRE).
AUCUNE PIÈCE RÉPARABLE PAR
L’UTILISATEUR NE SE TROUVE À
L’INTÉRIEUR. CONFIER TOUT ENTRETIEN À
UN PERSONNEL QUALIFIÉ UNIQUEMENT.

Ce point d’exclamation, placé dans un
triangle équilatéral, a pour but d’attirer
l’attention de l’utilisateur sur la présence,
dans les documents qui accompagnent
l’appareil, d’explications importantes du
point de vue de l’exploitation ou de
l’entretien.

D3-4-2-1-1b_A1_Fr

REMARQUE

L’AVERTISSEMENT DE PIÈCES NON RÉPARABLES PAR L’ UTILISATEUR SE TROUVE SUR LE DESSOUS DE L’APPAREIL.

D3-7-13-68_A1_

11)

Read these instructions.

1)

Keep these instructions.

2)

Heed all warnings.

3)

Follow all instructions.

4)

Do not use this apparatus near water.

5)

Clean only with dry cloth.

6)

Do not block any ventilation openings. Install in

7)

Only use attachments/accessories specified by
the manufacturer.

12)

Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.

accordance with the manufacturer’s
instructions.
Do not install near any heat sources such as

8)

radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
Do not defeat the safety purpose of the polarized

9)
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or

10)
pinched particularly at plugs, convenience

13)

Unplug this apparatus during lightning storms
or when unused for long periods of time.

14)

Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,

does not operate normally, or has been dropped.
receptacles, and the point where they exit from
the apparatus.

D3-7-13-69_En

Fr

En

2

WARNING

This equipment is not waterproof. To prevent a fire or

AVERTISSEMENT

shock hazard, do not place any container filled with
liquid near this equipment (such as a vase or flower
pot) or expose it to dripping, splashing, rain or
moisture.

WARNING

This product equipped with a three-wire grounding
(earthed) plug - a plug that has a third (grounding) pin.
This plug only fits a grounding-type power outlet. If you
are unable to insert the plug into an outlet, contact a
licensed electrician to replace the outlet with a properly
grounded one. Do not defeat the safety purpose of the
grounding plug.

WARNING

To prevent a fire hazard, do not place any naked flame
sources (such as a lighted candle) on the equipment.

VENTILATION CAUTION

When installing this unit, make sure to leave space
around the unit for ventilation to improve heat radiation
(at least 5 cm at rear, and 5 cm at each side).

WARNING

Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product,
and to protect it from overheating. To prevent fire
hazard, the openings should never be blocked or
covered with items (such as newspapers, table-cloths,
curtains) or by operating the equipment on thick carpet
or a bed.

Operating Environment

Operating environment temperature and humidity:
+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light).

CAUTION

This product is evaluated in moderate climate
condition. D3-8-2-1-7b_A1_En

The graphical symbol placed on the product
means alternating current.
The graphical symbol placed on the product
means direct current.
The graphical symbol placed on the product
means Class II equipment.

CAUTION

The switch on this unit will not completely shut off
all power from the AC outlet. Since the power cord
serves as the main disconnect device for the unit,
you will need to unplug it from the AC outlet to shut
down all power. Therefore, make sure the unit has
been installed so that the power cord can be easily
unplugged from the AC outlet in case of an accident.
To avoid fire hazard, the power cord should also be
unplugged from the AC outlet when left unused for a
long period of time (for example, when on vacation).

When using this product, confirm the safety
information shown on the bottom of the unit.

D3-4-2-1-3_A1_En

D3-4-2-1-6_A1_En

D3-4-2-1-7a_A1_En

D3-4-2-1-7b*_A1_En

D3-4-2-1-7c*_A2_En

D3-8-2-4_A1_En

D3-4-2-2-2a*_A1_En

D3-4-2-2-4_B1_En

Cet appareil n’est pas étanche. Pour éviter les risques
d’incendie et de décharge électrique, ne placez près de lui
un récipient rempli d’eau, tel qu’un vase ou un pot de
fleurs, et ne l’exposez pas à des gouttes d’eau, des
éclaboussures, de la pluie ou de l’humidité.

AVERTISSEMENT

Cet appareil est muni d’une fiche de mise à la terre
(masse) à trois fils. Comme la fiche présente une
troisième broche (de terre), elle ne peut se brancher
que sur une prise de courant, prévue pour une mise à
la terre. Si vous n’arrivez pas à insérer la fiche dans la
prise de courant, contactez un électricien qualifié pour
faire remplacer la prise par une qui soit mise à la terre.
N’annulez pas la fonction de sécurité que procure cette
fiche de mise à la terre.

AVERTISSEMENT

Pour éviter les risques d’incendie, ne placez aucune flamme
nue (telle qu’une bougie allumée) sur l’appareil.

D3-4-2-1-7a_A1_Fr

PRÉCAUTION DE VENTILATION

Lors de l’installation de l’appareil, veillez à laisser un
espace suffisant autour de ses parois de manière à
améliorer la dissipation de chaleur (au moins 5 cm à
l’arrière et 5 cm de chaque côté).

AVERTISSEMENT

Les fentes et ouvertures du coffret sont prévues pour la
ventilation, pour assurer un fonctionnement stable de l’appareil
et pour éviter sa surchauffe. Pour éviter les risques d’incendie,
ne bouchez jamais les ouvertures et ne les recouvrez pas
d’objets, tels que journaux, nappes ou rideaux, et n’utilisez pas
l’appareil posé sur un tapis épais ou un lit.

D3-4-2-1-7b*_A1_Fr

Milieu de fonctionnement

Température et humidité du milieu de fonctionnement :
De +5 °C à +35 °C (de +41 °F à +95 °F) ; Humidité relative
inférieure à 85 % (orifices de ventilation non obstrués)

N’installez pas l’appareil dans un endroit mal ventilé ou
un lieu soumis à une forte humidité ou en plein soleil
(ou à une forte lumière artificielle).

ATTENTION

Ce produit a été testé dans des conditions de climat
tempéré.

Le symbole graphique indiqué sur le produit
représente le courant alternatif.
Le symbole graphique indiqué sur le produit
représente le courant continu.
Le symbole graphique indiqué sur le produit
représente un équipement de Classe II.

ATTENTION

L’interrupteur de cet appareil ne coupe pas
complètement celui-ci de sa prise secteur. Comme le
cordon d’alimentation fait office de dispositif de
déconnexion du secteur, il devra être débranché au niveau
de la prise secteur pour que l’appareil soit complètement
hors tension. Par conséquent, veillez à installer l’appareil
de telle manière que son cordon d’alimentation puisse être
facilement débranché de la prise secteur en cas
d’accident. Pour éviter tout risque d’incendie, le cordon
d’alimentation sera débranché au niveau de la prise
secteur si vous prévoyez une période prolongée de non
utilisation (par exemple avant un départ en vacances).

Lorsque vous utilisez ce produit, vérifiez les informations
concernant la sécurité sous l’appareil.

D3-4-2-1-7c*_A1_Fr

D3-8-2-1-7b_A1_Fr

D3-4-2-2-2a*_A1_Fr

D3-4-2-2-4_B1_Fr

D3-4-2-1-3_A1_Fr

D3-4-2-1-6_A1_Fr

D3-8-2-4_A1_Fr

En

3

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

D8-10-1-2_A1_En

FEDERAL COMMUNICATIONS COMMISSION DECLARATION OF CONFORMITY

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Product Name: DJ SAMPLER
Model Number: DJS-1000
Responsible Party Name: PIONEER ELECTRONICS (USA) INC.
SERVICE SUPPORT DIVISION
Address: 1925 E. DOMINGUEZ ST. LONG BEACH, CA 90810-1003, U.S.A.
Phone: [phone]
URL: http://www.pioneerelectronics.com

[Supplied power cord]

The supplied power cord is designed specifically for
120 V. Do not use it with a voltage other than 120 V.
Doing so may cause a fire or electric shock.

D3-7-14_PDJ_A1_En

Information to User

Alterations or modifications carried out without
appropriate authorization may invalidate the user’s
right to operate the equipment.

D8-10-2_A1_En

[Cordon d’alimentation fourni]

Le cordon d’alimentation fourni est conçu spécialement
pour une tension de 120 V. Ne l’utilisez pas avec une
tension autre que 120 V.
Cela pourrait provoquer un incendie ou un choc électrique.

The Safety of Your Ears is in Your Hands

Get the most out of your equipment by playing it at a safe level
– a level that lets the sound come through clearly without
annoying blaring or distortion and, most importantly, without
affecting your sensitive hearing. Sound can be deceiving. Over

D8-10-4*_C1_En

D3-7-14_PDJ_A1_Fr

time, your hearing “comfort level” adapts to higher volumes of

CAUTION

This product satisfies FCC regulations when shielded
cables and connectors are used to connect the unit
to other equipment. To prevent electromagnetic
interference with electric appliances such as radios
and televisions, use shielded cables and connectors
for connections.

D8-10-3a_A1_En

sound, so what sounds “normal” can actually be loud and
harmful to your hearing. Guard against this by setting your
equipment at a safe level BEFORE your hearing adapts.

ESTABLISH A SAFE LEVEL:

• Set your volume control at a low setting.

• Slowly increase the sound until you can hear it
comfortably and clearly, without distortion.

• Once you have established a comfortable sound
level, set the dial and leave it there.

IMPORTANT NOTICE

THE MODEL NUMBER AND SERIAL NUMBER OF
THIS EQUIPMENT ARE ON THE REAR OR BOTTOM.
RECORD THESE NUMBERS ON PAGE 15 FOR
FUTURE REFERENCE.

D36-AP9-3*_A1_En

Recording equipment and copyright: You may use

this product only to reproduce or copy materials for
which you own the copyright or have obtained
permission to copy from the copyright owner or for
which you otherwise have a legal right to reproduce
or copy. Unless you own the copyright or have
obtained permission from the copyright owner or
otherwise have a legal right to reproduce or copy, you
may be violating the law, including copyright law, and
may be subject to payment of damages and other
remedies.

K018US_A1_En

BE SURE TO OBSERVE THE FOLLOWING
GUIDELINES:

• Do not turn up the volume so high that you can’t
hear what’s around you.

• Use caution or temporarily discontinue use in
potentially hazardous situations.

• Do not use headphones while operating a motorized
vehicle; the use of headphones may create a traffic
hazard and is illegal in many areas.

S001a_A1_En

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the plug by
tugging the cord and never touch the power cord when your
hands are wet as this could cause a short circuit or electric
shock. Do not place the unit, a piece of furniture, etc., on the
power cord, or pinch the cord. Never make a knot in the cord or
tie it with other cords. The power cords should be routed such
that they are not likely to be stepped on. A damaged power
cord can cause a fire or give you an electrical shock. Check the
power cord once in a while. When you find it damaged, ask
your nearest service center or your dealer for a replacement.

S002*_A1_En

En

4

Contents

How to read this manual

Thank you for purchasing this Pioneer DJ product.
Read this manual and the Operating Instructions that is available on the
Pioneer DJ site before using the product. Both contain important infor­mation that you should understand to properly use the product.
After you finish reading through the documents, keep them in a safe
place for future reference.
This manual provides brief descriptions of the part names and the con­nection between the unit and peripherals. For more instructions on how
to use this product, refer to the Operating Instructions for this product.
For obtaining the Operating Instructions for this product, see Obtaining
the Operating Instructions (p. 6 ).

Before start

Features ....................................................................................................... 6

Obtaining the Operating Instructions....................................................... 6

Accessories ................................................................................................. 6

Supported media ........................................................................................ 6

Part names

Top panel ..................................................................................................... 7

Front panel .................................................................................................. 8

Connections

Connecting to the input/output terminals................................................ 9

Example of connections ........................................................................... 10

Operation

Playing a demo project............................................................................. 11

Creating a new project ............................................................................. 11

Loading a sample to a track ..................................................................... 11

Creating a pattern ..................................................................................... 12

Connecting a USB device ........................................................................ 12

Disconnecting a USB device ................................................................... 12

Additional information

Troubleshooting ........................................................................................ 13

Changing the settings .............................................................................. 13

Cleaning the touch display ...................................................................... 13

Trademarks and registered trademarks ................................................. 13

Cautions on copyrights ............................................................................ 13

Specifications............................................................................................ 13

En

5