Pioneer DJM-T1 User Manual [en, de, fr]

DJ MIXER

DJM-T1

TABLE DE MIXAGE DJ-MISCHPULT

http://www.prodjnet.com/support/

The Pioneer website shown above offers FAQs, information on software and various other types of information and services to allow you to use your product in greater comfort.

Le site Pioneer ci-dessus offre une FAQ, des informations sur le logiciel et divers types d’informations et de services permettant de tirer le meilleur parti de ce produit.

Die oben gezeigte Pioneer-Website enthält häufig gestellte Fragen, Informationen über Software und andere wichtige Informationen und Dienste, die Ihnen helfen, Ihr Produkt optimal zu verwenden.

Operating Instructions Mode d’emploi Bedienungsanleitung

Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference. In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explanatory drawings. However the method of connecting and operating the unit is the same.

IMPORTANT

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel.

IMPORTANT: THE MOULDED PLUG

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 10 amp fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 10 amps and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark or the BSI mark on the body of the fuse.

If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be obtained from your local dealer.

If the fitted moulded plug is unsuitable for your socket outlet, then the fuse shall be removed and the plug cut off and disposed of safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code: Blue : Neutral Brown : Live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows;

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

D3-4-2-1-1_A1_En

D3-4-2-1-2-2*_A2_En

WARNING

This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filled with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture.

D3-4-2-1-3_A1_En

WARNING

Before plugging in for the first time, read the following section carefully.

The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e.g., 230 V or 120 V) written on the side panel.

D3-4-2-1-4*_A1_En

WARNING

To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A1_En

Operating Environment

Operating environment temperature and humidity: +5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light)

D3-4-2-1-7c*_A1_En

VENTILATION CAUTION

When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 5 cm at rear, and 3 cm at each side).

WARNING

Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed.

D3-4-2-1-7b*_A1_En

If the AC plug of this unit does not match the AC outlet you want to use, the plug must be removed and appropriate one fitted. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. If connected to an AC outlet, the cut-off plug can cause severe electrical shock. Make sure it is properly disposed of after removal. The equipment should be disconnected by removing the mains plug from the wall socket when left unused for a long period of time (for example, when on vacation).

D3-4-2-2-1a_A1_En

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement.

S002*_A1_En

CAUTION

The POWER switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation).

D3-4-2-2-2a*_A1_En

Before making or changing the connections, switch off the power and disconnect the power cord from the AC outlet.

D44-9-3_A1_En

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Private households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar new one).

For countries not mentioned above, please contact your local authorities for the correct method of disposal.

By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

K058b_A1_En

Contents

How to read this manual

! The names of displays, menus, and buttons in this manual are enclosed in

brackets. (e.g. [MASTER] channel, [ON/OFF], [File] menu)

! Descriptions of functions and procedures performed on the computer are indi-

TRAKTOR

cated [

! The TRAKTOR 2 Application Reference and TRAKTOR 2 Getting Started

can be viewed from the TRAKTOR help menu after TRAKTOR is installed.

Before start

Features .............................................................................................................................5

What’s in the box ..............................................................................................................5

Quick Start Guide

Operation overview ...........................................................................................................6

Installing the TRAKTOR software ....................................................................................6

Launching TRAKTOR .......................................................................................................7

Making the initial settings using the setup wizard ........................................................7

Performing product activation ........................................................................................8

Installing the driver software ...........................................................................................9

Connecting the input/output terminals ........................................................................11

Setting this unit ...............................................................................................................12

Changing the setting utility’s settings ..........................................................................12

Playing tracks ..................................................................................................................12

Operation

Browse section ...............................................................................................................14

Transport section ............................................................................................................15

Mixer section ...................................................................................................................17

Effect section ...................................................................................................................19

Hot cue/sampler section ................................................................................................21

Global section .................................................................................................................23

MIC/AUX section ............................................................................................................23

MIDI section ....................................................................................................................23

SHIFT section ..................................................................................................................24

Changing the settings

Changing the TRAKTOR Preferences ...........................................................................25

Changing the setting utility’s settings ..........................................................................25

Changing this unit’s settings.........................................................................................27

MIDI assignment map

MIDI assignment map ....................................................................................................28

Additional information

Troubleshooting ..............................................................................................................30

Block Diagram ................................................................................................................31

About trademarks and registered trademarks ............................................................31

Cautions on copyrights ..................................................................................................31

Specifications..................................................................................................................32

Before start

English

Features

This unit is a 2-channel mixer optimally designed for DJ performances using the TRAKTOR SCRATCH DJ software by Native Instruments. Through a collaboration with Native Instruments, it includes the “TRAKTOR SCRATCH DUO 2” DJ software equipped with a number of features required for DJ performances. For the hardware, the unit comes with a built-in controller for operating the many functions of TRAKTOR SCRATCH without hesitation and a sound card for simple connection to a computer. A DVS (Digital Vinyl System) can be created by combining this unit with your DJ player or analog player. Also, this unit carries over the technology of the Pioneer DJM series which has gained a high reputation for both quality and performance, offering powerful support for not only home use but also DJ performances in club scenes. ! An even greater variety of performance functions can be enjoyed by updating to

TRAKTOR SCRATCH PRO 2 (for a fee).

INTERNAL TRAKTOR CONTROLLER

This unit includes a controller optimized for TRAKTOR SCRATCH operations. TRAKTOR SCRATCH can be operated accurately, without procuring a separate controller in addition to this unit. The section for operating the browse and transport functions is located at the top of the mixer section in function of the series of operating procedures from selecting tracks to mixing. The sections for operating the performance functions (EFFECT, LOOP, HOT CUE and SAMPLER) are placed independently at the sides for the different channels in function of the player’s layout for intuitive operation.

PLUG AND PLAY

This unit is equipped with a built-in USB sound card for connecting a computer. A computer can be connected simply using a single USB cable; there is no need to procure a separate sound card in addition to this unit. DJ performances using “TRAKTOR SCRATCH DUO 2” can be started immediately, with no complicated settings.

What’s in the box

! TRAKTOR SCRATCH DUO 2 software DVD-ROM ! TRAKTOR SCRATCH CONTROL CD ×2 ! TRAKTOR SCRATCH CONTROL VINYL ×2 ! Driver software CD-ROM ! USB cable ! Power cord ! Warranty card ! Operating instructions (this document)

HIGH DURABILITY FADER

The crossfader uses a uniquely developed magnetic system. This improves durability, maintaining smooth operation for scratch playing over a long period of time. Furthermore, the operating load, fader curve and cut lag can be adjusted to the user’s tastes. The channel fader uses a sliding structure with the fader knob supported by two metal shafts. This provides smooth operation with no shakiness and approximately 3 times the endurance as compared to previous Pioneer products. In addition, a newly developed fader is used to minimize the influence of any liquids or dust getting inside the fader.

HIGH SOUND QUALITY

Thanks to the built-in sound card, sound output from a computer can be input to this unit in digital format, eliminating any decrease in sound quality. In addition, this unit’s audio input/output circuitry includes a high performance D/A converter and unique analog circuit technology reducing digital noise, faithfully reproducing the original sound to provide powerful, high quality club sound.

Quick Start Guide

This section describes the procedure for using this unit as a DVS (Digital Vinyl System).

! Descriptions of functions and procedures performed on the computer are indicated [

TRAKTOR

Operation overview

1 Installing the TRAKTOR software

= page 6

2 Launching TRAKTOR

= page 7

3 Making the initial settings using the setup wizard

= page 7

4 Performing product activation

= page 8

5 Installing the driver software

= page 9

6 Connecting the input/output terminals

= page 11

7 Setting this unit

= page 12

8 Changing the setting utility’s settings

= page 12

9 Playing tracks

= page 12

Installing the TRAKTOR software

! This unit also supports TRAKTOR SCRATCH PRO 2. If you own TRAKTOR SCRATCH PRO 2, update the software to the latest version.

the computer is in the proper conditions to provide constant high performance (for example by keeping the AC power connected) when using TRAKTOR.

Installation Procedure (Windows)

1 Insert the included TRAKTOR SCRATCH DUO 2 software DVD-ROM into the computer’s DVD drive.

2 From the Windows [Start] menu, double-click the [Computer (or My Computer)] > [Traktor 2] icon.

The contents of the DVD-ROM are displayed.

3 Double-click [Traktor 2 Setup.exe].

The TRAKTOR installer is launched.

4 Once the TRAKTOR installer is launched, click [Next].

— To return to the previous screen: Click [Back]. — To cancel installation: Click [Cancel].

Cautions on installing the TRAKTOR software

Supported operating systems

Mac OS X

7 Home Premium/Professional/Ultimate

Windows

Windows Vista Ultimate (SP1 or later)

Windows

For the latest information on the operating environment and compatibility, and to acquire the latest operating system, please visit the following Native Instruments website: http://www.native-instruments.com/

Minimum operating environment for TRAKTOR

CPU

Required memory

Hard disk Free space of 500 MB or greater DVD drive Optical disc drive on which DVD-ROMs are readable

Internet connection

USB 2.0 port A USB 2.0 port is required to connect the computer with this unit.

! Full functionality is not guaranteed on all computers, even those meeting the operating

environment requirements described above.

! Even with the required memory indicated for the operating environment above, lack of mem-

ory due to resident programs, the number of services, etc., could prevent the software from offering optimal functionality and performance. In such cases, free up sufficient memory. We recommend installing additional memory for stable operation.

! Depending on the computer’s power-saving settings, etc., the CPU and hard disk may not

provide sufficient processing capabilities. For notebook computers in particular, make sure

Home Basic/Home Premium/Business/

XP Home Edition/Professional (SP3 or later) 32-bit version

For Mac OS X

For Windows Windows Vista® and Windows® XP

2 GB or more of RAM

An Internet connection environment is required for user registration with Native Instruments, to update the TRAKTOR software, etc. Use the most recent version of the web browser.

Macintosh computer equipped with an Intel Duo processor

PC/AT compatible computer equipped with a 2.4 GHz or greater Intel® Pentium® 4, Intel® Core™ Duo or AMD Athlon™ 64 processor

10.5

10.6 32-bit version 64-bit version 32-bit version 64-bit version

Core™

5 Read the contents of the [License Agreement] carefully,

and if you agree, check [I accept the terms of the license agreement], then click [Next].

If you do not agree to the terms of the [License Agreement], click [Cancel] to cancel installation.

6 Choose the type of TRAKTOR installation, then click [Next].

Normally install all options, including [Controller Editor] and [Service Center].

7 Choose where to install TRAKTOR, then click [Next].

To choose the normal place of installation, simply click [Next]. To install in a different location, click [Change...], choose the place of installation, then click [Next].

8 Select the Native Instruments hardware driver, then click [Next].

Check the check box for your hardware.

9 To install the Traktor Kontrol X1 or Traktor Kontrol S4 driver, check the check box, then click [Next].

10 When the following screen appears, click [Next].

Installation begins. The installation completed screen appears once installation is completed.

11 Click [Finish].

This completes the installation procedure.

Installation Procedure (Macintosh)

1 Insert the included TRAKTOR SCRATCH DUO 2 software DVD-ROM into the computer’s DVD drive.

The [Traktor 2] icon appears on the screen.

2 Double-click the [Traktor 2] icon.

The contents of the DVD-ROM are displayed.

3 Double-click [Traktor 2 Installer.mpkg].

The TRAKTOR installer is launched.

4 Once the TRAKTOR installer is launched, click [Continue].

English

7 Select the Native Instruments hardware driver, then click [Continue].

Check the check box for your hardware.

8 Choose where to install TRAKTOR, then click [Install].

To choose the normal place of installation, simply click [Install]. To install in a different location, click [Change Install Location...], choose the place of installation, then click [Install]. Installation begins. The installation completed screen appears once installation is completed.

9 Click [Restart].

This completes the installation procedure.

Launching TRAKTOR

For Windows

From the Windows [Start] menu, open [All Programs] > [Native Instruments] > [Traktor 2], then click the [Traktor 2] icon.

5 Read the contents of the license agreement carefully, then click [Continue].

For Mac OS X

In Finder, open the [Application] folder, next open [Native Instruments] > [Traktor 2], then double-click the [Traktor] icon.

Making the initial settings using the setup wizard

When TRAKTOR is first launched, the setup wizard appears. Operate following the instructions on the screen to making the initial settings required to operate this unit. ! The setup wizard can also be launched from TRAKTOR [Help] menu >

[Start Setup Wizard].

1 At the [HARDWARE CONTROLLER SETUP] screen, select [Yes], then click [Next].

6 If you agree to the contents of the usage agreement, click [Agree].

If you do not agree to the contents of the usage agreement, click [Disagree] to cancel installation.

2 At the [HARDWARE CONTROLLER SELECTION] screen, select [Pioneer] at [manufacturer], [DJM-T1] at [model], then click [Next].

3 At the [TIMECODE CONTROLLER SELECTION] screen, select [CD(Audio 4/8 DJ)], then click [Next].

Performing product activation

To use TRAKTOR SCRATCH DUO 2, first perform product activation (referred to simply as “activation” below) using Native Instruments SERVICE CENTER (referred to simply as “SERVICE CENTER” below).

Launching the SERVICE CENTER

There are three ways to do this:

— Launching from the dialog displayed when TRAKTOR is started up — Launching from the TRAKTOR [Help] menu — Launching SERVICE CENTER directly

 To launch from the dialog displayed when TRAKTOR is

started up

1 Launch the TRAKTOR.

The screen below appears.

4 At the [DECK SETUP SELECTION] screen, select [2Track Decks + 2Sample Decks(Scratch)], then click [Next].

5 At the [YOUR TRAKTOR SETUP] screen, click [Finish].

! This dialog is displayed each time TRAKTOR is launched until the license is

acquired from SERVICE CENTER.

2 Select the method for acquiring the license, then click.

— [Run Demo]: Launch TRAKTOR in the demo mode. — [Buy]: Purchase TRAKTOR from the Native Instruments online shop. — [Activate]: Acquire the license immediately from the SERVICE CENTER.

 To launch from the TRAKTOR [Help] menu

From the TRAKTOR [Help] menu, click [Launch Service Center].

 To launch the SERVICE CENTER directly

For Windows

From the Windows [Start] menu, click the [Native Instruments] > [Service Center] > [Service Center] icons.

For Mac OS X

In Finder, open the [Application] folder, then double-click the [Service Center] > [Service Center] icons.

Activation procedure

— Online activation: When your computer is connected to the Internet — Offline activation: When your computer is not connected to the Internet

 Online activation

This completes the initial settings.

1 Launch the SERVICE CENTER.

The log-in screen is displayed.

2 Input your e-mail address and password, then click [Log in].

! When logging in for the first time, you must create a new user account. When [Create new User Account] is clicked, the new user account registration

screen appears.

Input the required items (e-mail address, first and last names), select your coun-

try/region, then click [Next].

When the registration information confirmation screen appears, check the

contents, then click [OK].

A password is sent to the e-mail address input on the form. Return to the log-in

screen and log in.

! The personal information input when registering a new user account may

be collected, processed and used based on the privacy policy on the Native Instruments website.

PIONEER CORPORATION does not collect, process or use this personal

information.

3 Input the serial number indicated on the package of the TRAKTOR SCRATCH DUO 2 software DVD-ROM, then click [Activate].

4 Input the serial number indicated on the package of the TRAKTOR SCRATCH DUO 2 software DVD-ROM, then click [Create].

A launch request file is created. Save this file on a USB device, etc.

5 Connect the USB device on which the launch request file is saved to the computer that can be connected to the Internet.

6 Double-click the launch request file on the computer that can be connected to the Internet.

The web browser is launched.

7 Once the product activation screen appears, click [Send].

8 Input your e-mail address and password, then click [SUBMIT].

! When logging in for the first time, you must create a new user account. When [No - I do not have an NI account.] is checked and [SUBMIT] is clicked,

the new user account registration screen appears.

Input the required items (e-mail address, first and last names, street address,

city and postal code), select your country/region, then click [NEXT].

When a survey screen appears, select answers to the various questions, then

click [SUBMIT].

A password is sent to the e-mail address input on the form. Return to the log-in

screen and log in.

! The personal information input when registering a new user account may

be collected, processed and used based on the privacy policy on the Native Instruments website.

PIONEER CORPORATION does not collect, process or use this personal

information.

9 When the [Service Center Activation Page] appears, click [NEXT].

10 Check that [Product] is [TRAKTOR SCRATCH DUO 2] and [Status] is [OK], then click [NEXT].

A launch return file is created. Save this file on a USB device, etc.

11 Launch the SERVICE CENTER on the computer on which TRAKTOR SCRATCH DUO 2 is to be installed.

12 Click [Offline] at [Continue without connecting to the internet].

13 Click [Open] at [Open Activation Return File].

The launch return file is loaded.

14 Check in the SERVICE CENTER that product activation has completed.

English

4 Once the product license registration successful screen appears, click [Exit].

 Offline activation

To activate TRAKTOR SCRATCH DUO 2 installed on a computer that is not connected to the Internet, use SERVICE CENTER in the offline mode. With this procedure, a second computer that can be connected to the Internet is required.

1 Launch the SERVICE CENTER on the computer on which TRAKTOR SCRATCH DUO 2 is to be installed.

2 Click [Offline] at [Continue without connecting to the internet].

3 Click [Create] at [Create Activation Request File].

Installing the driver software

This driver software is designed exclusively for inputting and outputting sound from the computer. To use this unit connected to a computer on which a Windows or Mac OS is installed, first install this driver software on the computer.

Software end user license agreement

This Software End User License Agreement (“Agreement”) is between you (both the individual installing the Program and any single legal entity for which the individual is acting) (“You” or “Your”) and PIONEER CORPORATION (“Pioneer”). TAKING ANY STEP TO SET UP OR INSTALL THE PROGRAM MEANS THAT YOU ACCEPT ALL OF THE TERMS OF THIS LICENSE AGREEMENT. PERMISSION TO DOWNLOAD AND/OR USE THE PROGRAM IS EXPRESSLY CONDITIONED ON YOUR FOLLOWING THESE TERMS. WRITTEN OR ELECTRONIC APPROVAL IS NOT REQUIRED TO MAKE THIS AGREEMENT VALID AND ENFORCEABLE. IF YOU DO NOT AGREE TO ALL OF THE TERMS OF THIS AGREEMENT, YOU ARE NOT AUTHORIZED TO USE THE PROGRAM AND MUST STOP INSTALLING IT OR UNINSTALL IT, AS APPLICABLE.

1 Definitions

1 “Documentation” means written documentation, specifications and help

content made generally available by Pioneer to aid in installing and using the Program.

2 “Program” means all or any part of Pioneer’s software licensed to You by

Pioneer under this Agreement.

2 Program license

1 Limited License. Subject to this Agreement’s restrictions, Pioneer grants to

You a limited, non-exclusive, nontransferable, license (without the right to sublicense): a To install a single copy of the Program on the hard disk drive of Your

computer, to use the Program only for Your personal purpose complying with this Agreement and the Documentation (“Authorized Use”);

b To use the Documentation in support of Your Authorized Use; and c To make one copy of the Program solely for backup purposes, provided

that all titles and trademark, copyright and restricted rights notices are reproduced on the copy.

2 Restrictions. You will not copy or use the Program or Documentation except

as expressly permitted by this Agreement. You will not transfer, sublicense, rent, lease or lend the Program, or use it for third-party training, commercial time-sharing or service bureau use. You will not Yourself or through any third party modify, reverse engineer, disassemble or decompile the Program, except to the extent expressly permitted by applicable law, and then only after You have notified Pioneer in writing of Your intended activities. You will not use the Program on multiple processors without Pioneer’s prior written consent.

3 Ownership. Pioneer or its licensor retains all right, title and interest in and to

all patent, copyright, trademark, trade secret and other intellectual property rights in the Program and Documentation, and any derivative works thereof. You do not acquire any other rights, express or implied, beyond the limited license set forth in this Agreement.

4 No Support. Pioneer has no obligation to provide support, maintenance,

upgrades, modifications or new releases for the Program or Documentation under this Agreement.

3 Warranty disclaimer

THE PROGRAM AND DOCUMENTATION ARE PROVIDED “AS IS” WITHOUT ANY REPRESENTATIONS OR WARRANTIES, AND YOU AGREE TO USE THEM AT YOUR SOLE RISK. TO THE FULLEST EXTENT PERMISSIBLE BY LAW, PIONEER EXPRESSLY DISCLAIMS ALL WARRANTIES OF ANY KIND WITH RESPECT TO THE PROGRAM AND DOCUMENTATION, WHETHER EXPRESS, IMPLIED, STATUTORY, OR ARISING OUT OF COURSE OF PERFORMANCE, COURSE OF DEALING OR USAGE OF TRADE, INCLUDING ANY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, SATISFACTORY QUALITY, ACCURACY, TITLE OR NON-INFRINGEMENT.

4 Damages and remedies for breach

You agree that any breach of this Agreement’s restrictions would cause Pioneer irreparable harm for which money damages alone would be inadequate. In addition to damages and any other remedies to which Pioneer may be entitled, You agree that Pioneer may seek injunctive relief to prevent the actual, threatened or continued breach of this Agreement.

5 Termination

Pioneer may terminate this Agreement at any time upon Your breach of any provision. If this Agreement is terminated, You will stop using the Program, permanently delete it from the computer where it resides, and destroy all copies of the Program and Documentation in Your possession, confirming to Pioneer in writing that You have done so. Sections 2.2, 2.3, 2.4, 3, 4, 5 and 6 will continue in effect after this Agreement’s termination.

6 General terms

1 Limitation of Liability. In no event will Pioneer or its subsidiaries be liable

in connection with this Agreement or its subject matter, under any theory of liability, for any indirect, incidental, special, consequential or punitive damages, or damages for lost profits, revenue, business, savings, data, use, or cost of substitute procurement, even if advised of the possibility of such damages or if such damages are foreseeable. In no event will Pioneer’s liability for all damages exceed the amounts actually paid by You to Pioneer or its subsidiaries for the Program. The parties acknowledge that the liability limits and risk allocation in this Agreement are reflected in the Program price and are essential elements of the bargain between the parties, without which Pioneer would not have provided the Program or entered into this Agreement.

2 The limitations or exclusions of warranties and liability contained in this

Agreement do not affect or prejudice Your statutory rights as consumer and shall apply to You only to the extent such limitations or exclusions are permitted under the laws of the jurisdiction where You are located.

3 Severability and Waiver. If any provision of this Agreement is held to be

illegal, invalid or otherwise unenforceable, that provision will be enforced to the extent possible or, if incapable of enforcement, deemed to be severed and deleted from this Agreement, and the remainder will continue in full force and effect. The waiver by either party of any default or breach of this Agreement will not waive any other or subsequent default or breach.

4 No Assignment. You may not assign, sell, transfer, delegate or otherwise

dispose of this Agreement or any rights or obligations under it, whether voluntarily or involuntarily, by operation of law or otherwise, without Pioneer’s prior written consent. Any purported assignment, transfer or delegation by You will be null and void. Subject to the foregoing, this Agreement will be binding upon and will inure to the benefit of the parties and their respective successors and assigns.

5 Entire Agreement. This Agreement constitutes the entire agreement between

the parties and supersedes all prior or contemporaneous agreements or representations, whether written or oral, concerning its subject matter. This Agreement may not be modified or amended without Pioneer’s prior and express written consent, and no other act, document, usage or custom will be deemed to amend or modify this Agreement.

6 You agree that this Agreement shall be governed and construed by and

under the laws of Japan.

Before installing the driver software

! Read Software end user license agreement carefully. ! Turn off this unit’s power switch, then disconnect the USB cable connecting this

unit and the computer.

! If any other programs are running on the computer, quit them. ! To install or uninstall the driver software, you need to be authorized by the

administrator of your computer. Log on as the administrator of your computer before proceeding with the installation.

! If you connect this unit to your computer without installing the driver soft-

ware first, an error may occur on your computer depending on the system environment.

! If installation of the driver software is interrupted after it has started, start the

installation procedure over again from the beginning.

! The provided CD-ROM includes installation programs in the following 12

languages.

English, French, German, Italian, Dutch, Spanish, Portuguese, Russian, Chinese

(simplified characters), Chinese (traditional characters), Korean, Japanese.

When using an operating system in any language besides the ones listed above,

select [English] during the installation procedure.

Supported operating systems

Windows® 7 Home Premium/Professional/Ultimate

Windows Vista Ultimate

Windows Mac OS X 10.4.8 or later 32-bit version

Mac OS X 10.6

! Windows

Home Basic/Home Premium/Business/

XP Home Edition/Professional (SP2 or later) 32-bit version

XP Professional x64 Edition is not supported.

32-bit version 64-bit version 32-bit version 64-bit version

32-bit version 64-bit version

Installation Procedure (Windows)

1 Insert the included driver software CD-ROM into the computer’s DVD drive.

2 Once the CD-ROM’s menu is displayed, double-click [DJMT1_X.XXX.exe].

3 Proceed with installation according to the instructions on the screen.

If [Windows Security] appears on the screen while the installation is in progress, click [Install this driver software anyway] and continue with the installation. ! When installing on Windows XP If [Hardware Installation] appears on the screen while the installation is in

progress, click [Continue Anyway] and continue with the installation.

! When the installation program is completed, a completion message appears.

Installation Procedure (Macintosh)

1 Insert the included driver software CD-ROM into the computer’s DVD drive.

2 Double-click [CD_menu].

3 Double-click [DJM-T1AudioDriver.dmg].

4 Double-click [DJM-T1AudioDriver.pkg].

5 Proceed with installation according to the instructions on the screen.

Connecting the input/output terminals

Analog player DJ player Analog player DJ player

Be sure to turn off the power and unplug the power cord from the power outlet whenever making or changing connections. Connect the power cord after all the connections between devices have been completed. Be sure to use the included power cord. Refer to the operating instructions for the component to be connected. ! When creating a DVS (Digital Vinyl System) combining a computer, audio interface, etc., be careful in connecting the audio interface to this unit’s input terminals and in

the settings of the input selector switches.

Also refer to the operating instructions of the DJ software and audio interface.

Rear panel, front panel

Headphones

English

POWER

220 - 240V

AC IN

To power outlet

OFF ON

CH 2

PHONO CD

2 3

BOOTH

TRS

Power amplifier

SIGNAL GND

MASTER 1

3.COLD

(for booth monitor)

1 POWER button

Turns this unit’s power on and off.

2 PHONO terminals

Connect to a phono level (MM cartridge) output device. Do not input line level signals. To connect a device to the [PHONO] terminals, remove the short-circuit pin plug inserted in the terminals. Insert this short-circuit pin plug into the [PHONO] terminals when nothing is connected to them to cut external noise.

3 CD terminals

Connect to a DJ player or a line level output component.

4 SIGNAL GND terminal

Connect an analog player’s ground wire here. This helps reduce noise when the analog player is connected.

5 Cord hook

Hook the USB cable here. ! The sound will be interrupted if the USB cable is disconnected during

playback.

6 Kensington security slot

7 USB port

Connect to a computer.

! Connect this unit and the computer directly using the included USB cable. ! A USB hub cannot be used.

8 MASTER2 terminals

Connect to a power amplifier, etc.

9 MASTER ATT.

Sets the attenuation level of the sound output from the [MASTER1] and [MASTER2] terminals. When set to [–6 dB], the audio level output from the [MASTER1] and [MASTER2] terminals is decreased by half.

a MASTER1 terminals

Connect to a power amplifier, etc.

CH 1

PHONOCD

2 3

1.GND 2.HOT

MASTER

ATT.

Power amplifierPower amplifier

MASTER 2

RLL

USB

Computers

PHONES

d e

MIC

Microphones

AUX

Portable

audio device

b BOOTH terminals (page 18)

Output terminals for a booth monitor, compatible with balanced or unbalanced output for a TRS connector. ! The sound will be distorted if the level is raised too high when using unbal-

anced outputs.

c AC IN

Connect to a power outlet using the included power cord. Wait until all connections between the equipment are completed before connecting the power cord. Be sure to use the included power cord.

d PHONES terminal (page 18)

Connect headphones here.

e MIC terminal (page 23)

Connect a microphone here.

f AUX IN terminals (page 23)

Connect to the output terminal of an external device (sampler, portable audio device, etc.)

 Cord hook

The USB cable is fastened in place by catching it on the cord hook. This prevents the USB cable from being pulled accidentally and its plug getting disconnected from the port. ! The sound will be interrupted if the USB cable is disconnected during playback.

USB

USB cable

TER 2

Setting this unit

Be sure to install this unit’s exclusive driver software before connecting this unit and the a computer by USB cable.

1 Switch the [CD, PHONO, USB] input selector switch.

Set it to [USB].

USBCD

PHONO

2 Connect this unit to your computer via a USB cable.

This unit functions as an audio device conforming to the ASIO standards.

! This operation does not work with computers that do not support USB 2.0. ! When using applications supporting ASIO, [USB 1/2], [USB 3/4] and [USB 5/6]

can be used as inputs.

! The computer’s recommended operating environment depends on the DJ appli-

cation. Be sure to check the recommended operating environment for the DJ application you are using.

! When another USB audio device is connected to the computer at the same time,

it may not operate or be recognized normally. We recommend only connecting the computer and this unit. ! When connecting the computer and this unit, we recommend connecting

directly to this unit’s USB port.

3 Press [POWER] button.

Turn on the power of this unit. ! The message [Installing device driver software] may appear when this unit is

first connected to the computer or when it is connected to a different USB port

on the computer. Wait a while until the message [Your devices are ready for

use] appears. ! When installing on Windows XP

— [Can Windows connect to Windows Update to search for software?]

may appear while the installation is in progress. Select [No, not this time], then click [Next] to continue installation.

— [What do you want the wizard to do?] may appear while the instal-

lation is in progress. Select [Install the software automatically (Recommended)], then click [Next] to continue installation.

— If [Windows Security] appears on the screen while the installation is in

progress, click [Install this driver software anyway] and continue with the installation.

Changing the setting utility’s settings

1 Displaying the setting utility

! For Windows

Click [Start] menu > [All Programs] > [Pioneer] > [DJM-T1] > [DJM-T1

Setting Utility]. ! For Mac OS X Click [Macintosh HD] icon > [Application] > [Pioneer] > [DJM-T1] >

[DJM-T1 Setting Utility].

2 Click the [MIXER OUTPUT] tab.

3 Click the [Mixer Audio Output] pull-down menu.

Set as shown below, according to the devices connected to this unit.

When using a DJ player (CONTROL CD)

USB 1/2 CH1 Timecode CD CH1 Timecode PHONO

USB 3/4 CH2 Timecode CD CH2 Timecode PHONO

When using an analog player (CONTROL VINYL)

Playing tracks

1 Set the CONTROL CD in the DJ player.

! To use an analog player, set the CONTROL VINYL.

2 Set TRAKTOR to the [Scratch Control] mode.

TRAKTOR

Check that the right section of the [d] button in TRAKTOR is displayed as shown below.

! If [CUE] and [CUP] are displayed, operate the computer to switch TRAKTOR to

the [Scratch Control] mode.

3 Press the [f (REL.)] or [CUE (ABS.)] button while pressing the [SHIFT] button.

Select the Relative or Absolute mode.

— Press the [f (REL.)] button while pressing the [SHIFT] button: Switches to

the Relative mode.

The Relative mode is a mode that ignores the playback position of the

CONTROL CD/CONTROL VINYL.

— Press the [CUE (ABS.)] button while pressing the [SHIFT] button: Switches to

the Absolute mode.

The Absolute mode is a mode that reflects the playback position of the

CONTROL CD/CONTROL VINYL on the playback position of the track.

4 Turn the rotary selector.

Select the track.

BROWSE VIEW

TREE FLD OPEN

5 Press the [LOAD (DUPLICATE)] button.

The selected track is loaded in the deck.

LOAD

DUPLICATE

! For detailed instructions on selecting tracks and loading tracks in decks, see

Browse section on page 14.

6 Play the CONTROL CD.

Playback of the track loaded in the TRAKTOR deck begins. ! To use an analog player, play the CONTROL VINYL.

7 Check the time code signal status.

Check that TRAKTOR is properly recognizing the time code signals (signals recorded on CONTROL CD/CONTROL VINYL). ! The time code signal status can be checked at the deck’s scope screen. To display the scope screen, select [Scope] from the pull-down menu for

the deck on which the CONTROL CD/CONTROL VINYL is to be used from [Preferences] > [Decks] > [Platter / Scope].

When TRAKTOR is recognizing the time code signals properly, a double circle is

displayed on the scope screen, as shown on the diagram below.

! For details on the scope screen, also see “12 Setting Up TRAKTOR Scratch” in

the TRAKTOR 2 Application Reference.

PUSH

LOAD

DUPLICATE

Operation

MIDI

ON/OFF

CH1 CH2

SNAP

QUANTIZE

GROUP

/ SINGLE

LFO

SELECT

LFO

DECK A /C

FX1

UTILITY

WAKE UP

DRY/WET

1221

LOAD

DUPLICATE

DUPLICATE DUPLICATE

DECK ADECK B

DECK A

CUE

CUE CUE

BROWSE VIEW

REL. REL.ABS. ABS.

FX ASSIGN

FX1 FX2 SYNC

BEND BEND

PHONO

TRIM

LOW

TREE FLD OPEN

TREE

FLD OPEN

SYNC

MASTER MASTER

MASTER

MASTER1

OVER

USBCD

MID

HEADPHONES

MIXING

MASTERCUE

LEVEL

LOAD

DUPLICATE

DECK B

PUSH

FX ASSIGN

FX1 FX2

PHONO

TRIM

MID

LOW

English

POWER

MASTER

BOOTH MONITOR

CUE

USBCD

BOOTH MONITOR

FX2

DRY/WET

DECK B /D

SELECT

GROUP

/ SINGLE

LFO

LOOP

MOVE

HOT CUESAMPLER

SAMPLE

LEVEL

AUTO LOOP

SELECT

CROSS.F. CONTROL

DEL DEL

DEL DEL DEL DEL

ACTIVE

PLAY MODE

PLAY MODE PLAY MODE

PHONES

LRAUX

CUE

TAP

10 9

9 8

8 7

7 6

6 5

5 4

4 3

3 2

2 1

1 0

CH 1CH 2

MIC AUXOFF

SHIFT

LOCK

2 CHANNEL TRAKTOR MIXER

DJM -T1

CUE

TAP

FEELING ADJ.

SAMPLE

LEVEL

9 8

8 7

7 6

6 5

5 4

4 3

3 2

2 1

1 0

LOWLEVELINPUT SELECTMIC

EQ HI

AUTO LOOP

SELECT

CROSS.F. CONTROL

SAMPLER HOT CUE

DEL DEL

PLAY MODE

CROSS F.

REVERSE

CROSS F. CURVE

THRU

CROSS F. REVERSE

ON OFF

LOOP

MOVE

ACTIVE

121212120

1 Browse section (page 14)

2 Transport section (page 15)

3 Mixer section (page 17)

4 Effect section (page 19)

5 Hot cue/sampler section (page 21)

6 Global section (page 23)

7 MIDI section (page 23)

8 MIC/AUX section (page 23)

9 SHIFT section (page 24)

1 UTILITY (WAKE UP) button

! Press: The standby mode is canceled (page 27). ! Press for over 1 second: Switches to the mode for changing this unit’s settings (page 27).

2 POWER indicator

Lights when this unit’s power is on.

Browse section

DECK ADECK B

LOAD

REL. REL.

BROWSE VIEW

PUSH

DUPLICATE DUPLICATE

CUE ABS. CUEABS.TREE FLD OPEN

(SHIFT)+

2 2

1 LOAD (DUPLICATE) button

! Press: The track selected with the cursor is loaded in the respective deck. ! [SHIFT] + press: The track loaded in the one deck is copied and loaded into the other deck.

2 Rotary selector

! Turn: The cursor in the [TRACK] area moves. ! Press: The [BROWSE] area’s magnified display turns on and off. ! [SHIFT] + turn: The cursor in the [TREE] area moves. ! [SHIFT] + press: The folder opens/closes. * Description of areas

— [TREE] area: Section 1 on the diagram above is called the [TREE] area.

— [TRACK] area: Section 2 on the diagram above is called the [TRACK]

area.

— [FAVORITES] area: Section 3 on the diagram above is called the

[FAVORITES] area.

— [BROWSE] area: Sections 1, 2 and 3 on the diagram above are collec-

tively called the [BROWSE] area.

Importing tracks to TRAKTOR

TRAKTOR

From Explorer or Finder, drag & drop music files or folders containing music files to [Track Collection] in TRAKTOR’s [TREE] area.

! Right-click [Track Collection] (on Mac OS X, click [Track Collection] while

pressing the [control] key), then select [Import Music Folders] from the menu. All the music files in your system’s [My Music] or [Music] folder are imported.

 Creating playlists

1 Right-click [Playlists] in TRAKTOR’s [TREE] area.

! For Mac OS X, click it while pressing the [control] key.

2 From the menu, select [Create Playlist].

3 Input the playlist name, then click [OK].

The playlist you have created is displayed at [Playlists].

4 Drag & drop music files to the playlist you have created to add them.

(Press)

Loading tracks to decks

1 Turn the rotary selector while pressing the [SHIFT] button.

Select the playlist or folder.

2 Press the rotary selector while pressing the [SHIFT] button.

The folder opens/closes. ! Items without the [+] mark cannot be opened/closed.

3 Release the [SHIFT] button and turn the rotary selector.

Select the track.

4 Press the [LOAD (DUPLICATE)] button.

The selected track is loaded in the deck. ! When a track is loaded while the [BROWSE] area is enlarged, the [BROWSE]

area returns to its regular size.

 Playing iTunes music files

If you are managing music files with iTunes, the iTunes library and playlists can be accessed directly with the TRAKTOR browser.

1 Turn the rotary selector while pressing the [SHIFT] button.

Select the [iTunes] folder.

2 Press the rotary selector while pressing the [SHIFT] button.

The folder opens/closes.

3 Browsing the library and playlists in the same way as with iTunes

! The iTunes library and playlists cannot be edited with the TRAKTOR browser. ! When played from the TRAKTOR browser, iTunes music files are automatically

imported to the TRAKTOR [Track Collection] list.

Using the duplicate function

This function allows you to easily copy tracks that are loaded in one of the decks onto the other deck. ! The following describes the procedure for copying a track from deck [A] onto

deck [B].

1 Select the track, then press the [LOAD (DUPLICATE)] button of the deck [A].

The track is loaded into deck [A].

2 Press the [LOAD (DUPLICATE)] button of the deck [B] while pressing the [SHIFT] button.

The track loaded in deck [A] is copied and loaded into deck [B].

 Creating a FAVORITES

Drag and drop a playlist folder to an open slot in the [FAVORITES] area.

Transport section

DECK ADECK B

FX ASSIGN

FX1 FX2 SYNC

BROWSE VIEW

PUSH

FX ASSIGN

FX1 FX2SYNC

TREE FLD OPEN

MASTER MASTER

REL. REL.ABS. ABS.

CUE CUE

BEND BEND

English

1 2

4 4

3 3

Internal Playback mode

(SHIFT)+

1 f (REL.) button

! Press: Use this to play/pause tracks. ! [SHIFT] + press: The TRAKTOR playback tracking mode switches to the Relative mode. The Relative mode is a mode that ignores the playback position of the

CONTROL CD/CONTROL VINYL.

2 CUE (ABS.) button

While pausing ! Press: A cue point is set at the paused position.

— When the [SNAP] function of TRAKTOR is off: The cue point is set to the currently paused position, regardless of the

[Beat Grid]. — When the [SNAP] function of TRAKTOR is on: The cue point is set to the same position as the nearest [Beat Grid].

During playback ! Press: Playback returns to the set cue point and cues, and playback pauses (back

cue).

If the [CUE (ABS.)] button is pressed and held in after returning to the cue

point, playback continues as long as the button is held.

! [SHIFT] + press: The TRAKTOR playback tracking mode switches to the Absolute mode. The Absolute mode is a mode that reflects the playback position of the

CONTROL CD/CONTROL VINYL on the playback position of the track.

3 FX ASSIGN (s BEND t) button

! Press the [FX 1] button: TRAKTOR effect unit [FX 1] is assigned to the deck whose button is pressed. ! Press the [FX 2] button: TRAKTOR effect unit [FX 2] is assigned to the deck whose button is pressed.

* When using TRAKTOR SCRATCH DUO 2, the assignment is fixed: [FX 1]

to deck [A], [FX 2] to deck [B]. If you upgrade to TRAKTOR SCRATCH PRO 2, [FX 1] and [FX 2] can be

assigned freely to the desired deck.

! Press the [SHIFT] + [FX 1] buttons: The track’s playing speed temporarily slows down. ! Press the [SHIFT] + [FX 2] buttons: The track’s playing speed temporarily speeds up.

4 SYNC (MASTER) button

! Press: The [BPM] and [Beat Grid] of the track for the deck whose button was

pressed are synchronized to the master for synchronization.

! [SHIFT] + press: The deck whose button was pressed is set as the master for synchronization.

Scratch Control mode

(SHIFT)+

Playback

Press the [f (REL.)] button.

 Pausing

During playback, press the [f (REL.)] button.

Set the cue

1 During playback, press the [f (REL.)] button.

Playback is paused.

2 Press the [CUE (ABS.)] button.

Cue point [a] is set at the position at which playback was paused. No sound is output at this time. ! When a new Cue Point is set, the previously set Cue Point is deleted.

 Returning to Cue Point (Back Cue)

During playback, press the [CUE (ABS.)] button.

The set immediately returns to the currently set cue point and pauses. ! When the [f (REL.)] button is pressed, playback starts from the cue point.

 Checking Cue Point (Cue Point Sampler)

Press and hold the [CUE (ABS.)] button after returning to the cue point.

Playback starts from the set cue point. Playback continues while the [CUE (ABS.)] button is pressed.

Bending the pitch

Press the [FX 1] or [FX 2] button while pressing the [SHIFT] button.

— Press the [SHIFT] + [FX 1] buttons: The track’s playing speed temporarily slows down. — Press the [SHIFT] + [FX 2] buttons: The track’s playing speed temporarily speeds up.

Synchronizing the playing speed with other decks (beat sync)

1 Press the [SYNC (MASTER)] button while pressing the [SHIFT] button on the currently playing deck.

The deck whose button was pressed is set as the master for synchronization.

2 Press the [SYNC (MASTER)] button on the deck not set as the master for synchronization.

The [BPM] and [Beat Grid] of the track for the deck not set as the master for synchronization are synchronized to the [BPM] and [Beat Grid] of the track for the deck set to the master for synchronization.

! For information about setting the master for synchronization, see Setting the

master for synchronization on page 16.

! The beat sync function may not operate properly in the following cases.

— When the loop length is under 1 beat. — When the track has not been analyzed.

 Setting the master for synchronization

TRAKTOR

Click [ ].

The master for synchronization can be selected from one of the two types below.

— [MASTER]: The BPM value input by the user or the BPM value set by tapping

is set as the master.

— [AUTO]: The master is set automatically. When two decks are playing and

the deck set as the master is paused, the other deck is automatically set as the master.

! When using TRAKTOR SCRATCH DUO 2, this is always set to [AUTO]. If you

upgrade to TRAKTOR SCRATCH PRO 2, you can select [MASTER] or [AUTO].

Mixer section

CUE

USBCD

PHONO

USBCD

PHONO

HEADPHONES

MASTER1

OVER

TAP

CUE

TAP

SHIFT

LOCK

CH 1CH 2

FEELING ADJ.

DJM -T1

2 CHANNEL TRAKTOR MIXER

SAMPLE

LEVEL

CRO

CROSS F. REVERSE

SAMP

PLAY MO

TRIM

MID

LOW

TRIM

MID

LOW

LEVEL

MIXING

MASTERCUE

BOOTH MONITOR

MASTER

English

CROSS F. CURVE

THRU

CROSS F. REVERSE

ON OFF

1 MASTER LEVEL control

Adjusts the audio level output from the [MASTER1] and [MASTER2] terminals.

2 BOOTH MONITOR control

Adjusts the level of audio signals output from the [BOOTH] terminal.

3 CD, PHONO, USB input selector switch

Select the input source of each channel from the components connected to this unit.

— [CD]: Selects the DJ player connected to the [CD] terminals. — [PHONO]: Selects the analog player connected to the [PHONO] terminals. — [USB]: Selects the sound of the computer connected to the [USB] port.

4 TRIM control

Adjusts the level of audio signals input in each channel.

5 EQ (HI, MID, LOW) controls

These adjust the sound quality of the respective channels. These adjust the [HI] (high range), [MID] (middle range) and [LOW] (low range), respectively.

6 CUE (TAP) button

7 Channel fader

8 Crossfader

9 Channel Level Indicator

! Press: Press the [CUE (TAP)] button for the channel you want to monitor. ! [SHIFT] + press: The BPM value shown on the TRAKTOR tempo display can be set by pressing

four times in beat with the track’s tempo.

Adjusts the level of audio signals output in each channel.

The sound of the respective channels is output according to the curve characteristics selected with the [CROSS F. CURVE (THRU,

Displays the sound level of the respective channels before passing through the channel faders.

a Master Level Indicator

Displays the audio level output from the [MASTER1] and [MASTER2] terminals.

b HEADPHONES MIXING control

Adjusts the monitor volume balance between the sound of the channel whose [CUE (TAP)] button is pressed and the [MASTER] channel sound.

c HEADPHONES LEVEL control

Adjusts the audio level output from the [PHONES] terminal.

d FEELING ADJ. adjustment hole

This can be used to adjust the crossfader’s operating load.

e CROSS F. REVERSE indicator

Lights when the [CROSS F. REVERSE] switch is on.

f CROSS F. CURVE (THRU, , ) selector switch

This switches the crossfader curve characteristics.

g CROSS F. REVERSE switch

Turns the crossfader reverse function on and off.

Do not pull on the channel fader and crossfader knobs with excessive force. The knobs are not designed to be removed. Pulling the knobs strongly may result in damaging the unit.

Outputting sound

Set the volume of the power amplifiers connected to the [MASTER1] and [MASTER2] terminals to a suitable level. Note that loud sound will be produced if the volume is set too high.

1 Switch the [CD, PHONO, USB] input selector switch.

Select the input source of each channel from the components connected to this unit.

2 Turn the [TRIM] control.

Adjusts the level of audio signals input in each channel.

3 Move the channel fader away from you.

Adjusts the level of audio signals output in each channel.

4 Set the crossfader.

Switch the channel whose sound is output from the speakers.

, )] selector switch.

— Left edge: The [CH 1] sound is output. — Center position: The sound of [CH 1] and [CH 2] is mixed and output. — Right edge: The [CH 2] sound is output.

! This operation is not necessary when the [CROSS F. CURVE (THRU, , )]

selector switch is set to [THRU].

5 Turn the [MASTER LEVEL] control.

Audio signals are output from the [MASTER1] and [MASTER2] terminals.

Adjusting the sound quality

Turn the [EQ (HI, MID, LOW)] controls for the respective channels.

Refer to Specifications on page 32 for the range of sound that can be adjusted by each control.

Monitoring sound with headphones

1 Connect headphones to the [PHONES] terminal.

2 Press the [CUE (TAP)] button for the channel you want to monitor.

3 Turn the [HEADPHONES MIXING] control.

Adjusts the monitor volume balance between the sound of the channel whose [CUE (TAP)] button is pressed and the [MASTER] channel sound. ! To monitor only the sound of the [MASTER] channel, turn the

[HEADPHONES MIXING] control clockwise from the center position.

4 Turn the [HEADPHONES LEVEL] control.

The sound of the channel whose [CUE (TAP)] button is pressed and the sound of the [MASTER] channel are mixed and output from the headphones. ! Monitoring is canceled when the [CUE (TAP)] button is pressed again.

Select the crossfader curve characteristics

Switch the [CROSS F. CURVE (THRU, , )] selector switch.

— [THRU]: Choose this when you do not want to use the crossfader. — [

]: Set here for a curve that rises gradually.

— [ ]: Sets an abruptly rising curve. (When the crossfader is moved away

from the edge on the [CH 1] side, the sound of the [CH 2] side is output immediately.)

Adjusting the crossfader’s operating load

The load (resistance) when the crossfader is operated can be adjusted using a flathead screwdriver. ! The crossfader’s attenuation curve and the play at the two edges of the fader (the

cut lag) can be adjusted. For details, see Changing this unit’s settings on page 27.

1 Move the crossfader to the right ([CH 2]) edge.

2 Insert the flathead screwdriver into the [FEELING ADJ.] adjustment hole and turn it.

— Turn clockwise: The load decreases (the resistance of fader movement gets

weaker).

— Turn counterclockwise: The load increases (the resistance of fader move-

ment gets stronger).

Using the fader reverse function

The crossfader’s operating direction can be reversed by turning the [CROSS F. REVERSE] switch on.

Set the [CROSS F. REVERSE] switch to [ON].

Audio is output from the [BOOTH] terminal

Turn the [BOOTH MONITOR] control.

Adjusts the level of audio signals output from the [BOOTH] terminal.

! The unit can also be set so that the sound of the microphone is not output from

the [BOOTH] terminal. For details, see Changing this unit’s settings on page 27.

Using the TAP function

The BPM value shown on the TRAKTOR tempo display can be set using the TAP function.

1 Load the track in the deck.

For details, see Loading tracks to decks on page 14.

2 Play the track.

For details, see Playback on page 15.

3 In beat with the track’s tempo, press the [CUE (TAP)] button four times while pressing the [SHIFT] button.

The average interval at which the [CUE (TAP)] button was pressed is set as the BPM value. ! This operation does not change the track’s tempo (playing speed).

Effect section

English

FX1

DRY/WET

1 3

2 4

GROUP / SINGLE

LFO

SELECT

LFO

1 ON (GROUP/SINGLE) button

When using in the [Group] mode ! Press: Does not function. ! [SHIFT] + press: Switches the effect panel mode. [Group] mode h [Single] mode When using in the [Single] mode ! Press: Turns the effect on and off. ! [SHIFT] + press: Switches the effect panel mode. [Group] mode h [Single] mode

— [Group] mode: Up to three effects can be selected and operated simultaneously per

effect panel. — [Single] mode: The parameters of the selected effect can be operated in detail. The [Single] mode cannot be selected with TRAKTOR SCRATCH DUO 2. If you upgrade to TRAKTOR SCRATCH PRO 2, the effect panel can be

switched to the [Single] mode.

2 Effect control buttons

When using in the [Group] mode ! Press: Turns the effects on and off. ! [SHIFT] + press:

— When [Generic Controller Mode] is turned on in this unit’s settings: Switches the effect type. — When [Generic Controller Mode] is turned off in this unit’s settings: Turns the LFO CONTROL function on and off.

When using in the [Single] mode ! Press the [1] button: Restores the parameters of all the effects to the base settings. ! Press the [2] or [3] button: Turns the respective effect parameter on and off. The type of parameter dif-

fers according to the effect.

! Press the [SHIFT] + [1] buttons:

! Press the [SHIFT] + [2] or [SHIFT] + [3] buttons:

— When [Generic Controller Mode] is turned on in this unit’s settings: Does not function. — When [Generic Controller Mode] is turned off in this unit’s settings: Turns the LFO CONTROL function on and off.

3 DRY/WET control

When using in the [Group] mode ! Turn: Adjusts the balance between the effect sound and original sound. ! [SHIFT] + turn: Does not function. When using in the [Single] mode ! Turn: Adjusts the balance between the effect sound and original sound. ! [SHIFT] + turn: Switches the effect type.

Group mode

(SHIFT)+2 (SHIFT)+

Single mode

3 2

1 4

(SHIFT)+2 (SHIFT)+

4 Effect control dials

When using in the [Group] mode ! Turn: Adjusts the degree of the respective effect. ! [SHIFT] + turn: Switches the effect type. * When the LFO CONTROL function is on

— Turn: Adjusts the cycle for changing the degree of each effects. — [SHIFT] + turn:

Does not function. When using in the [Single] mode ! Turn: Adjusts the respective parameter. ! [SHIFT] + turn: Does not function. * When the LFO CONTROL function is on

— Turn:

Adjusts the cycle at which the respective parameter changes.

— [SHIFT] + turn:

Does not function.

Using the effect function

! The following section describes the procedure for operating the effect function

in the [Group] mode.

1 Press the [FX 1] or [FX 2] button.

The TRAKTOR effect unit is assigned to the deck. ! When using TRAKTOR SCRATCH DUO 2, the assignment is fixed: [FX 1] to deck

[A], [FX 2] to deck [B].

If you upgrade to TRAKTOR SCRATCH PRO 2, [FX 1] and [FX 2] can be assigned

freely to the desired deck.

2 Turn an effect control dial while pressing the [SHIFT] button.

This selects the type of effect. ! When [Generic Controller Mode] is turned on in this unit’s settings, the type of

effect can also be selected by pressing an effect control button while pressing the [SHIFT] button.

3 Turn the effect control dial.

Adjusts the degree of the effect sound.

4 Press the effect control button.

This turns the effect on. ! When the button is pressed again, the effect is turned off.

5 Turn the [DRY/WET] control.

Adjust the balance between the effect sound for all of the effects together and the original sound.

Using the LFO CONTROL function

When the LFO CONTROL function is on, the parameter value of the effect sent to TRAKTOR can be changed at the specified speed. This function allows you to create unique effect sounds not possible through manual operation. With the LFO CONTROL function, effect control buttons [1] – [3] can each be set separately.

! First turn off [Generic Controller Mode] in this unit’s settings. For details, see

Changing this unit’s settings on page 27.

! The following section describes the procedure for operating the LFO CONTROL

function in the [Group] mode.

1 Turn an effect control dial while pressing the [SHIFT] button.

This selects the type of effect.

2 Press an effect control button while pressing the [SHIFT] button.

The LFO CONTROL function turns on. If the effect is off, it turns on simultaneously. ! When the same button is pressed again, the LFO CONTROL function turns off

and the effect turns back on.

3 Turn the effect control dial.

Adjusts the cycle for changing the degree of each effects.

4 Turn the [DRY/WET] control.

Adjust the balance between the effect sound for all of the effects together and the original sound.

Hot cue/sampler section

HOT CUE mode

DECK A /C

English

LOOP MOVE

AUTO LOOP

CROSS.F. CONTROL

HOT CUESAMPLER

DEL DEL

ACTIVE

SELECT

SAMPLE

LEVEL

PLAY MODE

SAMPLER mode

1 AUTO LOOP (LOOP MOVE/SAMPLE VOLUME) control

When using with the hot cue function ! Turn: Changes the loop size. ! Press: Turns loop playback on and off. ! [SHIFT] + turn: Moves the position of the loop. ! [SHIFT] + press: Does not function. When using with the sampler function ! [SHIFT] + turn: Adjusts the volume of the sample deck. ! [SHIFT] + press: Resets the volume of the sample deck to the base setting.

2 SELECT button

! Press: Switches the function of the hot cue/sampler section with each press. Hot cue function h Sampler function ! [SHIFT] + press: Turns the CROSS FADER CONTROL function on and off.

3 SELECT indicator

Lights or flashes according to the hot cue/sampler section’s function.

— When the hot cue function is set: Lights green. — When the sampler function is set: Lights orange. — When the CROSS FADER CONTROL function is on: Flashes green or orange.

4 HOT CUE/SAMPLER button

When using with the hot cue function ! Press:

— When no hot cue is set during playack or while pausing: A hot cue is set at the position at which the button is pressed. — When a hot cue is set during playback or while pausing:

Calls out the hot cue. ! [SHIFT] + press: Deletes the hot cue.

TRAKTOR

[CUE TYPE] (the type of hot cue) can be changed by clicking [b] to the

left of the [ ] icon. When using with the sampler function For details, see Table of HOT CUE/SAMPLER button operations on page 22.

5 ACTIVE button

When using with the hot cue function ! Press: Switches the playing mode of the loop registered at the hot cue. Loop is played h Loop is not played When using with the sampler function ! Press: Switches the button mode of the sample deck’s [HOT CUE/SAMPLER]

button. Sample play mode h Trigger play mode For details, see Table of HOT CUE/SAMPLER button operations on page 22.

(SHIFT)+

! [SHIFT] + press: Switches the loop mode of the sample on the sample deck. Loop play mode h One shot play mode

— [ ] Loop play mode: When the end of the sample is reached, sample playback returns to the

beginning and continues. — [ ] One shot play mode: When the end of the sample is reached, sample playback stops.

Using the hot cue function

1 Press the [SELECT] button.

The hot cue/sampler section switches to the hot cue function. Switches to the mode in which the [SELECT] indicator, [HOT CUE/SAMPLER] button and [ACTIVE] button light green.

2 Press the [HOT CUE/SAMPLER] button.

The hot cue is set to the position playing when the button is pressed. ! When the [HOT CUE/SAMPLER] button is pressed during loop playback, the

currently playing loop can be stored at the hot cue button.

! This operation is not necessary if a hot cue is already stored at the [HOT CUE/

SAMPLER] button.

3 During playback or while pausing, press the [HOT CUE/ SAMPLER] button.

The hot cue is called out. ! If a loop is stored at the [HOT CUE/SAMPLER] button, press the [ACTIVE] button

to switch the loop playback mode.

Using the sampler function

Samples can be loaded into the sample deck [C] and sample deck [D] sampler slots and played. ! When operating sample deck [C]:

— The deck [A] track is loaded into the sampler slot. — The [HOT CUE/SAMPLER] buttons on this unit’s [CH 1] side support the

respective sampler slots.

! When operating sample deck [D]:

— The deck [B] track is loaded into the sampler slot. — The [HOT CUE/SAMPLER] buttons on this unit’s [CH 2] side support the

respective sampler slots.

! The operation of the [HOT CUE/SAMPLER] buttons differ according to the

sample’s loop mode and the [HOT CUE/SAMPLER] button’s button mode. For details, see Table of HOT CUE/SAMPLER button operations.

! The following section explains the procedure for loading the deck [A] track in the

sample deck [C] sampler slot and playing it.

Operate the hot cue/sampler section on this unit’s [CH 1] side.

1 Load the track in deck [A].

2 Press the [SELECT] button.

Switch the hot cue/sampler section to the sampler function.

Switches to the mode in which the [SELECT] indicator, [HOT CUE/SAMPLER] button and [ACTIVE] button light orange.

3 Press the [HOT CUE/SAMPLER] button.

The track loaded in deck [A] is loaded into the sampler slot on sample deck [C].

! The section of the track starting from the position playing when the button was

pressed and equal to the auto loop’s loop size is sampled and loaded in the sampler slot.

! The track selected with the cursor in the [TRACK] area can be loaded into the

sampler slot by pressing the [HOT CUE/SAMPLER] button while pressing the [SHIFT] button. (Tracks with a playing time longer than 48 seconds cannot be loaded.)

4 Press the [ACTIVE] button while pressing the [SHIFT] button.

The sample’s loop mode switches.

— [ ] Loop play mode: When the end of the sample is reached, sample playback returns to the

beginning and continues. — [ ] One shot play mode: When the end of the sample is reached, sample playback stops.

5 Press the [ACTIVE] button.

The [HOT CUE/SAMPLER] button’s button mode switches.

— Sample play mode: The sample is played or muted each time the button is pressed. — Trigger play mode: When the button is pressed, the sample is played from the beginning, and

stops when the button is released.

! For details, see Table of HOT CUE/SAMPLER button operations on page 22.

6 Press the [HOT CUE/SAMPLER] button or press and hold the [HOT CUE/SAMPLER] button.

The sample is played.

! When the [HOT CUE/SAMPLER] button is pressed again or the [HOT CUE/

SAMPLER] button is release, output of the sample’s sound stops.

Using the CROSS FADER CONTROL function

CROSS FADER CONTROL is a function allowing you to call out hot cues and start playing samples in association with operation of the crossfader. ! First make the following preparations.

— Turn off [Generic Controller Mode] in this unit’s settings.

= See Changing this unit’s settings on page 27. — Register a hot cue in deck [A] or [B].

= See Using the hot cue function on page 21. — Load a sample in sample deck [C] or [D].

= See Using the sampler function on page 21.

! The section operated differs according to the decks to be associated.

— To associate deck [A] and sample deck [C]: Operate the hot cue/sampler section on this unit’s [CH 1] side. — To associate deck [B] and sample deck [D]: Operate the hot cue/sampler section on this unit’s [CH 2] side.

! When the [CROSS F. REVERSE] switch is on, the crossfader’s direction of opera-

tion is inverted.

1 Press the [SELECT] button while pressing the [SHIFT] button.

The CROSS FADER CONTROL function turns on. The [SELECT] indicator flashes. ! When the [SELECT] button is pressed again while pressing the [SHIFT] button,

the CROSS FADER CONTROL function turns off.

2 Press the [SELECT] button.

Select the function to be associated with the CROSS FADER CONTROL function (the hot cue function or the sampler function).

— To associate the hot cue function: Switches to the mode in which the [SELECT] indicator, [HOT CUE/SAMPLER]

button and [ACTIVE] button light and flash green. — To associate the sampler function: Switches to the mode in which the [SELECT] indicator, [HOT CUE/SAMPLER]

button and [ACTIVE] button light and flash orange.

! It is also possible to associate both the hot cue function and the sampler func-

tion with operation of the crossfader. (The hot cue and sample to be associated with the crossfader must be selected separately for each function.)

3 Press the [HOT CUE/SAMPLER] button.

Select the hot cue and sample to be associated with operation of the crossfader.

— To select a hot cue: Press the [HOT CUE/SAMPLER] button at which the hot cue is set. Only one

of hot cues [1] – [4] can be selected. — To select a sample: Press the [HOT CUE/SAMPLER] button at which the sample is loaded. Up to

four of samples [1] – [4] can be selected.

! With this procedure, the hot cue and sample are not played. ! When the [HOT CUE/SAMPLER] button is pressed again, the selection is

canceled.

4 Move the crossfader.

Move the crossfader to the side opposite the side to which the hot cue or sample to be associated with the CROSS FADER CONTROL function is set.

5 Move the crossfader.

When the crossfader is moved to the right from the [CH 1] edge, the deck [B] hot cue and sample deck [D] sample are played. When the crossfader is moved to the left from the [CH 2] edge, the deck [A] hot cue and sample deck [C] sample are played.

Table of HOT CUE/SAMPLER button operations

! Press:

Sampler slot

When no sample is loaded The music file loaded in the deck is loaded into the sampler slot as a sample.

When a sample is loaded Playback of the sample begins.

While playing a sample

1 The mode can be switched using the [ACTIVE] button (page 21). 2 When the sample is muted, muting is canceled.

Loop play mode Sample play mode

The sample is muted. When pressed for over 1 second, playback of the sample stops.

! [SHIFT] + press:

Sampler slot

When no sample is loaded The music file selected in the [TRACK] area is loaded in the sampler slot as a sample. When a sample is loaded The sample is deleted. While playing a sample The sample is deleted.

1 The mode can be switched using the [ACTIVE] button (page 21).

Loop play mode Sample play mode

Trigger play mode

The sample is played while the button is pressed. When the button is released, playback of the sample stops.

The sample is cued and playback continues.

Trigger play mode

One shot play mode Sample play mode

Playback of the sample begins.

Playback of the sample stops.

One shot play mode Sample play mode

Trigger play mode

The sample is played while the button is pressed. When the button is released, playback of the sample stops.

The sample is cued and playback continues.

Trigger play mode

Global section

MIDI section

English

SNAP

QUANTIZE

(SHIFT)+

1 SNAP (QUANTIZE) button

! Press: Turns the TRAKTOR snap function on and off. When the snap function is on, the cue and loop points are set to the same

position as the nearest [Beat Grid]. ! [SHIFT] + press: Turns the TRAKTOR quantize function on and off. When the quantize function is on, movement to the cue and loop points is

synchronized with the timing of the beats.

MIC/AUX section

MIC AUXOFF

21 3

LOWLEVELINPUT SELECT

1 INPUT SELECT switch

Switches the audio input between the external device and the microphone.

— [AUX]: The external device connected to the [AUX] terminals is selected. — [OFF]: The [MIC/AUX] channel is turned off. — [MIC]: The microphone connected to the [MIC] terminal is selected.

! The sound input to the [MIC] and [AUX] terminals is mixed with the [CH 1]

and [CH 2] sound that has passed through the crossfader.

2 LEVEL control

Adjusts the audio level input to the [MIC] and [AUX] terminals.

3 EQ (HI, LOW) controls

These adjust the tone of the [MIC/AUX] channel.

Inputting the sound of a microphone or external device

EQ HI

121212120

MIDI

ON/OFF

CH1 CH2

This unit outputs the operation information of buttons and controls in universal MIDI format. When connected by USB cable to a computer on which a MIDI-compatible DJ software program is installed, the DJ software can be operated from this unit.

Operating DJ software using the MIDI function

Install the DJ software on your computer in advance. Also, adjust the audio and MIDI settings for the DJ software.

! For MIDI channel setting instructions, see Setting the MIDI channel on page 26. ! For the messages output by this unit, see MIDI assignment map on page 28.

1 Connect this unit’s [USB] terminal to the computer.

For instructions on connections, see Connecting the input/output terminals on page 11.

2 Launch the DJ software.

3 Press the [CH 1] button.

The MIDI functions of the [CH 1] side’s [TRIM] control, [EQ (HI, MID, LOW)] controls, [CUE (TAP)] button, channel fader and crossfader A are activated. ! Crossfader A is the [CH 1] volume adjustment function extracted from the cross-

fader’s volume adjustment function.

! When the [CH 1] button is pressed again, the above MIDI functions are

deactivated.

4 Press the [CH 2] button.

The MIDI functions of the [CH 2] side’s [TRIM] control, [EQ (HI, MID, LOW)] controls, [CUE (TAP)] button, channel fader and crossfader B are activated. ! Crossfader B is the [CH 2] volume adjustment function extracted from the cross-

fader’s volume adjustment function.

! When the [CH 2] button is pressed again, the above MIDI functions are

deactivated.

5 Operate a button or control in the mixer section.

The MIDI message for the button or control being operated is sent.

6 Operate a button or control other than one in the mixer section.

The MIDI message for the button or control being operated is sent. ! The MIDI functions for the buttons and controls in the browse, transport, effect,

hot cue/sampler and global sections are always activated, regardless of the [CH

1] and [CH 2] buttons.

1 Connect the external device to the [MIC] or [AUX] terminal.

2 Switch the [INPUT SELECT] switch.

3 Turn the [LEVEL] control.

Adjust the audio level input to the [MIC] or [AUX] terminal.

! Pay attention that rotating to the extreme right position outputs a very loud

sound.

 Adjusting the sound quality

Turn the [EQ (HI, LOW)] controls.

Refer to Specifications on page 32 for the range of sound that can be adjusted by each control.

SHIFT section

SHIFT

LOCK

1 SHIFT button

! Press another button while pressing the [SHIFT] button: The other function (the second function) assigned to the pressed button or

control is called out. ! Press the [SHIFT] button twice: The [SHIFT] button is locked in the pressed status. To unlock it, press the

[SHIFT] button again. ! While locked, press another button while still pressing the [SHIFT] button: When the ADVANCED SHIFT function is on, the third function assigned to

the pressed button or control is called out. To cancel the ADVANCED SHIFT function, release your finger from the

[SHIFT] button.

Using the ADVANCED SHIFT function

By using the ADVANCED SHIFT function, you can callout the third function assigned to buttons or controls. When using together with DJ software, third MIDI codes different from the ones for when the [SHIFT] button is on or off can be input or output. ! Before using the ADVANCED SHIFT function, update this unit’s firmware to

version 2.00 or later. For instructions on checking the firmware version, see Checking the firmware version on page 27.

! You can freely assign functions as the third functions that are called out using

the ADVANCED SHIFT function. You can also use Pioneer’s recommended settings.

To use the ADVANCED SHIFT function with the recommended settings,

download the settings file from the Pioneer website and import the settings to TRAKTOR.

! For instructions on updating the firmware and acquiring and importing the set-

tings file, see the following Pioneer website:

http://www.prodjnet.com/support/ Firmware version 2.00 and a settings file supporting the ADVANCED SHIFT func-

tion are scheduled to be available in early September, 2011.

1 Press the [SHIFT] button twice.

The [SHIFT] button lights.

2 With the [SHIFT] button lit, keep pressing the [SHIFT] button.

The [SHIFT] button starts flashing.

3 Operate buttons or controls while still pressing the [SHIFT] button.

The third function assigned to the button or control is called out. With the ADVANCED SHIFT function, a third function can be assigned to the buttons or controls within the dotted lines on the diagram below. ! Three or more functions can be assigned to some buttons and controls. For details

on assigning functions (MIDI codes), see MIDI assignment map on page 28.

POWER

MIDI

ON/OFF

CH1 CH2

SNAP

QUANTIZE

FX1

GROUP

/ SINGLE

LFO

SELECT

LFO

DECK A /C

LOOP

MOVE

AUTO LOOP

SELECT

CROSS.F. CONTROL

HOT CUESAMPLER

DEL DEL

DEL DEL DEL DEL

ACTIVE

PHONES

LOAD

DUPLICATE

DUPLICATE DUPLICATE

UTILITY

DECK ADECK B

DECK A

WAKE UP

REL. REL.ABS. ABS.

FX ASSIGN

FX1 FX2 SYNC

BEND BEND

DRY/WET

PHONO

TRIM

LOW

SAMPLE

LEVEL

10 9

9 8

8 7

7 6

6 5

5 4

4 3

3 2

2 1

1 0

CH 1 CH 2

PLAY MODE

PLAY MODE PLAY MODE

PUSH

CUE

CUE CUE

BROWSE VIEW

TREE

FLD OPEN

TREE FLD OPEN

SYNC

MASTER

MASTER MASTER

MASTER1

OVER

USBCD

HEADPHONES

MID

MIXING

MASTERCUE

LEVEL

CUE

SHIFT

CUE

SHIFT

TAP

LOCK

2 CHANNEL TRAKTOR MIXER

DJM -T1

LOAD

DUPLICATE

DECK B

FX ASSIGN

FX1 FX2

PHONO

TRIM

MID

LOW

CUE

TAP

FEELING ADJ.

POWER

CUE

USBCD

10 9

BOOTH MONITOR

DRY/WET

SAMPLE

LEVEL

CROSS.F. CONTROL

SAMPLER HOT CUE

PLAY MODE

CROSS F.

REVERSE

MASTER

FX2

DECK B /D

AUTO LOOP

SELECT

DEL DEL

GROUP

/ SINGLE

LFO

SELECT

LFO

LOOP

MOVE

ACTIVE

Changing the settings

English

Changing the TRAKTOR Preferences

Change TRAKTOR’s environmental settings according to the usage conditions of your hardware. For details on the TRAKTOR environment settings, see TRAKTOR 2 Application Reference. ! If you wish to restore the changes to the environmental settings to their defaults,

please check the following website.

http://www.prodjnet.com/support/

1 Click the TRAKTOR [ (Preferences Button)] button.

Open the TRAKTOR settings menu.

2 Select the category and make the settings.

Updating the TRAKTOR software

When the computer is connected to the Internet, TRAKTOR software can be updated by accessing the Native Instruments SERVICE CENTER (referred to simply as “SERVICE CENTER” below).

1 Launch the SERVICE CENTER and log in.

For instructions on launching the SERVICE CENTER and logging in, see Launching the SERVICE CENTER on page 8.

2 Click the [Update] tab.

Available updates are checked.

3 Check the check box.

Specify the update to be downloaded.

Category Descriptions

Controller Manager

Traktor Kontrol X1

Traktor Kontrol S4

Assign TRAKTOR functions to this unit’s controls and buttons. Set this when using Native Instruments Traktor Kontrol X1. Set this when using Native Instruments Traktor Kontrol S4.

Changing the setting utility’s settings

The setting utility can be used to make the checks and settings described below.

— Checking the status of this unit’s [CD, PHONO, USB] input selector switch — Setting the source of audio data output from this unit to the computer — Adjusting the buffer size (when using Windows ASIO) — Setting the MIDI channel — Checking the version of the driver software

Displaying the setting utility

! When using TRAKTOR, be sure to quit the settings utility.

For Windows

Click [Start] menu > [All Programs] > [Pioneer] > [DJM-T1] > [DJM-T1 Setting Utility].

For Mac OS X

Click [Macintosh HD] icon > [Application] > [Pioneer] > [DJM-T1] > [DJM-T1 Setting Utility].

Checking the status of this unit’s [CD, PHONO, USB] input selector switch

Display the setting utility before starting.

Click the [MIXER INPUT] tab.

4 Click [Download].

Updating begins.

List of TRAKTOR SCRATCH DUO 2 setting items

Category Descriptions

Audio Setup

Output Routing

Input Routing

Timecode Setup

Transport

Decks

Mixer

Global Settings

Effects

Mix Recorder

Browser Details

File Management

Select the audio devices to be used for audio input/output. Set the audio latency when using a Macintosh computer.

Select [Mixing Mode]. — [Internal]: Select this to control TRAKTOR mixer section from this

unit. — [External]: Select this to use this unit. Set the association between the TRAKTOR deck’s audio outputs and this unit’s input channels.

Set the association between the TRAKTOR deck’s audio inputs and this unit’s output channels.

Set this to use time codes (CONTROL CD/CONTROL VINYL). Set the conditions and functions for loading tracks to the decks. Make the settings related to the tempo and key lock functions. Set the TRAKTOR deck section’s display method. Set auto gain to on or off.

Set the TRAKTOR mixer section’s display method. Set whether or not to display the global section. Set the types of effects to be displayed when selecting effects. Make the settings related to TRAKTOR recording functions. Make the settings related to the [BROWSE] area and fonts. Make the settings for track importing, auto analysis, the analysis BPM

range, etc.

Setting the source of audio data output from this unit to the computer

Display the setting utility before starting.

1 Click the [MIXER OUTPUT] tab.

2 Click the [Mixer Audio Output] pull-down menu.

Select and set the audio data to be output to the computer from the flow of audio signals inside this unit.

USB 1/2 USB 3/4 USB 5/6

CH1 Timecode PHONO

CH1 Timecode CD

— — — — — — — —

1: The sound output from [USB 1/2] and [USB 3/4] is output with the same volume as input to this unit, regardless of the [USB Output Level] setting.

3 Click the [USB Output Level] pull-down menu.

Adjust the volume of the audio data output from [USB 5/6].

! If not enough volume can be achieved with the DJ software’s volume adjustment

alone, change the [USB Output Level] setting to adjust the volume of the audio data output from this unit. Note that the sound will be distorted if the volume is raised too high.

CH2 Timecode PHONO

CH2 Timecode CD

Post CH1 Fader

Post CH2 Fader

Cross Fader A

Cross Fader B

MIC/AUX Post EQ

REC OUT

Adjusting the buffer size (when using Windows ASIO)

If an application using this unit as the default audio device (DJ software, etc.) is running, quit that application before adjusting the buffer size. Display the setting utility before starting.

Click the [ASIO] tab.

! If the buffer size is made large, drops in audio data (breaks in the sound)

occur less easily, but the time lag due to the delay in the transfer of the audio data (latency) increases.

Checking the version of the driver software

Display the setting utility before starting.

Click the [About] tab.

Setting the MIDI channel

Display the setting utility before starting.

1 Click the [MIDI] tab.

2 Click the [MIDI CHANNEL] pull-down menu.

Select the desired MIDI channel.

Checking the latest information on the driver software

For the latest information on the driver software for exclusive use with this unit, visit our website shown below. http://www.prodjnet.com/support/ ! Operation cannot be guaranteed when multiple units of this mixer are con-

nected to a single computer.

Changing this unit’s settings

English

1 Press the [UTILITY (WAKE UP)] button for over 1 second.

The [UTILITY (WAKE UP)] indicator and the top of the [CH 1] channel level indicator flash.

2 Press the [LOAD (DUPLICATE) B] button.

The setting item changes each time the [LOAD (DUPLICATE) B] button is pressed. The flashing position of the [CH 1] channel level indicator moves downwards. ! When the [LOAD (DUPLICATE) A] button is pressed, the selection returns to the

previous setting item.

The flashing position of the [CH 1] channel level indicator moves upwards.

3 Turn the rotary selector.

Change the setting value.

! When the setting value can be switched on and off

— On: The green section of the [CH 2] channel level indicator lights. — Off: The green section of the [CH 2] channel level indicator turns off.

! When the setting value can be switched in steps

— One’s place of setting value: Value indicated by the number of segments

of the [CH 2] channel level indicator that are lit.

— Ten’s place of setting value: Value indicated by the number of segments

of the master level indicator that are lit.

4 Press the rotary selector.

The settings are stored in this unit. The [UTILITY (WAKE UP)] button flashes rapidly. Do not turn this unit’s power off while the settings are being stored. ! Storing is completed when the [UTILITY (WAKE UP)] button switches from

flashing rapidly to flashing normally.

! Press the [UTILITY (WAKE UP)] button to return to normal operation.

About the auto standby function

When [Auto Standby] is set to [ON], the standby mode is set automatically if 4 hours pass with all of the conditions shown below met.

— That none of this unit’s buttons or controls are operated. — That no audio signals are input to this unit’s input terminals. — That no computer is connected by USB.

! When the [UTILITY (WAKE UP)] button is pressed, the standby mode is

canceled.

! This unit is shipped with the auto standby function turned on. If you do not want

to use the auto standby function, set [Auto Standby] to [OFF].

Checking the firmware version

1 Press the [UTILITY (WAKE UP)] button for over 1 second.

2 Press the [LOAD (DUPLICATE) A] button.

The firmware version is indicated by the segments of the channel level and master level indicators that light.

— Number of segments of the [CH 1] channel level indicator lit: One’s place — Number of segments of the master channel level indicator lit: First decimal

place

— Number of segments of the [CH 2] channel level indicator lit: Second deci-

mal place

Example: When version “1.07” is indicated

! If the top segment of the [CH 1] channel level indicator flashes, the firmware

version is one earlier than 2.00.

MASTER1

OVER

Setting preferences

Options settings

Cross Fader Cut Lag

Cross Fader Curve Slow A

Cross Fader Curve Slow B

Cross Fader Curve Fast A

Cross Fader Curve Fast B

Generic Controller Mode

Mic Output To Booth Monitor

Auto Standby

1 If the setting value is extremely small, the sound may not be completely muted even when the crossfader is positioned at the very edge. 2 If the setting value is small, the attenuation will have a gentle curve characteristic. If the setting value is large, the attenuation will have an abrupt curve characteristic.

Flashing position of [CH 1] channel level indicator

Setting value Default value Descriptions

Very top 0 to 52

Second from top 0 to 32

Third from top 0 to 32

Fourth from top 0 to 32

Fifth from top 0 to 32

Sixth from top ON/OFF

Seventh from top ON/OFF

Eighth from top ON/OFF

OFF

Adjusts the play at the edges of the crossfader (the cut lag). The cut lag can be adjusted between 0.74 mm and 5.94 mm, in 0.1 mm units.1

Adjusts the [CH 1] side attenuation curve characteristics when the [CROSS F. CURVE (THRU,

Adjusts the [CH 2] side attenuation curve characteristics when the [CROSS F. CURVE (THRU,

Adjusts the [CH 1] side attenuation curve characteristics when the [CROSS F. CURVE (THRU,

Adjusts the [CH 2] side attenuation curve characteristics when the [CROSS F. CURVE (THRU,

Turns on and off the function for selecting effects using the effect control buttons. When off, the LFO CONTROL and CROSS FADER CONTROL functions can be used.

Sets whether or not to output the microphone’s audio signals from [BOOTH] terminals.

, )] switch is set to [ ].2

Turns the auto standby function on and off.

MIDI assignment map

With TRAKTOR, MIDI messages for assigning TRAKTOR functions to MIDI are expressed “Note1 + English scale2” or “CC3 + control number”. On the table below, the MIDI messages output from this unit’s buttons and controls are indicated in the same way as in TRAKTOR.

1 “Note” is a MIDI term used when pressing or releasing notes on a piano or other keyboard. 2 The English scale indicates the tones using letters C, D, E, F, G, A and B and “#” indicating halftones. 3 “CC” is the abbreviation of “control change”. A control change is a type of MIDI signal used to transmit various types of control information, such as timbre, volume, etc.

On this unit, values from 0 to 127 are output as CC mainly when controls and faders are operated. CC are also output when certain buttons are operated.

MIDI assignment map

MIDI assignment

Category Button/control

Rotary selector (press) Note C-1 Note E4 Note F#8 — — — OFF=0, ON=127

Rotary selector (turn) CC 000 CC 064 CC 027 — — —

DECK A LOAD (DUPLICATE) button Note C#-1 Note F4 Note G8 — — — OFF=0, ON=127 DECK B LOAD (DUPLICATE) button Note D-1 Note F#4 Note G#8 — — — OFF=0, ON=127 DECK A f (REL.) button DECK B f (REL.) button

Transport section

Effect section

Mixer section

Global section SNAP (QUANTIZE) button Note C#3 Note F8 Note G9 Note C#3 Note F8 Note G9 OFF=0, ON=127

DECK A SYNC (MASTER) button Note F-1 Note A4 Note B8 Note F-1 Note A4 Note B8 OFF=0, ON=127 DECK B SYNC (MASTER) button Note F#-1 Note A#4 Note C9 Note F#-1 Note A#4 Note C9 OFF=0, ON=127 DECK A FX ASSIGN FX1 button Note G-1 Note B4 Note C#9 Note G-1 Note B4 Note C#9 OFF=0, ON=127 DECK B FX ASSIGN FX1 button Note G#-1 Note C5 Note D9 Note G#-1 Note C5 Note D9 OFF=0, ON=127 DECK A FX ASSIGN FX2 button Note A-1 Note C#5 Note D#9 Note A-1 Note C#5 Note D#9 OFF=0, ON=127 DECK B FX ASSIGN FX2 button Note A#-1 Note D5 Note E9 Note A#-1 Note D5 Note E9 OFF=0, ON=127 DECK A CUE (ABS.) button Note B-1 Note D#5 Note F9 Note B-1 Note D#5 Note F9 OFF=0, ON=127 DECK B CUE (ABS.) button Note C0 Note E5 Note F#9 Note C0 Note E5 Note F#9 OFF=0, ON=127 FX1 DRY/WET control CC 001 CC 065 CC 028 — — — 0-127 FX2 DRY/WET control CC 002 CC 066 CC 029 — — — 0-127 FX1 ON (GROUP/SINGLE) button Note C#0 Note F5 CC 030 Note C#0 Note F5 CC 030 OFF=0, ON=127 FX2 ON (GROUP/SINGLE) button Note D0 Note F#5 CC 031 Note D0 Note F#5 CC 031 OFF=0, ON=127 FX1 EFFECT1 control CC 003 CC 067 CC 032 — — — 0-127 FX2 EFFECT1 control CC 004 CC 068 CC 033 — — — 0-127 FX1 EFFECT1 button Note D#0 Note G5 CC 034 Note D#0 Note G5 CC 034 OFF=0, ON=127 FX2 EFFECT1 button Note E0 Note G#5 CC 035 Note E0 Note G#5 CC 035 OFF=0, ON=127 FX1 EFFECT2 control CC 005 CC 069 CC 036 — — — 0-127 FX2 EFFECT2 control CC 006 CC 070 CC 037 — — — 0-127 FX1 EFFECT2 button Note F0 Note A5 CC 038 Note F0 Note A5 CC 038 OFF=0, ON=127 FX2 EFFECT2 button Note F#0 Note A#5 CC 039 Note F#0 Note A#5 CC 039 OFF=0, ON=127 FX1 EFFECT3 control CC 007 CC 071 CC 040 — — — 0-127 FX2 EFFECT3 control CC 008 CC 072 CC 041 — — — 0-127 FX1 EFFECT3 button Note G0 Note B5 CC 042 Note G0 Note B5 CC 042 OFF=0, ON=127 FX2 EFFECT3 button Note G#0 Note C6 CC 043 Note G#0 Note C6 CC 043 OFF=0, ON=127 CH 1 TRIM control CC 013 CC 077 CC 089 — — — 0-127 CH 2 TR

IM control CC 014 CC 078 CC 090 — — — 0-127 CH 1 HI control CC 015 CC 079 CC 091 — — — 0-127 CH 2 HI control CC 016 CC 080 CC 092 — — — 0-127 CH 1 MID control CC 017 CC 081 CC 093 — — — 0-127 CH 2 MID control CC 018 CC 082 CC 094 — — — 0-127 CH 1 LOW control CC 019 CC 083 CC 095 — — — 0-127 CH 2 LOW control CC 020 CC 084 CC 096 — — — 0-127 CH 1 CUE (TAP) button Note B2 Note D#8 Note D4 — Note D#8 Note D4 OFF=0, ON=127 CH 2 CUE (TAP) button Note C3 Note E8 Note D#4 — Note E8 Note D#4 OFF=0, ON=127 CH 1 channel fader CC 021 CC 085 CC 097 — — — 0-127 CH 2 channel fader CC 022 CC 086 CC 098 — — — 0-127 CROSS FADER A CC 023 CC 087 CC 099 — — — 0-127 CROSS FADER B CC 024 CC 088 CC 100 — — — 0-127

(this unit d computer)

SHIFT OFF SHIFT ON

Note D#-1 Note G4 Note A8 Note D#-1 Note G4 Note A8 OFF=0, ON=127 Note E-1 Note G#4 Note A#8 Note E-1 Note G#4 Note A#8 OFF=0, ON=127

ADVANCED

SHIFT

MIDI assignment

(computer d this unit)

SHIFT OFF SHIFT ON

ADVANCED

SHIFT

Transmitted data

Turn clockwise: 0 – +30 / Turn counterclockwise: -1 – -30

Category Button/control

DECK A AUTO LOOP (LOOP MOVE/SAMPLE

VOLUME) control (press) DECK A AUTO LOOP

(LOOP MOVE/SAMPLE

VOLUME) control (turn) DECK B AUTO LOOP

(LOOP MOVE/SAMPLE VOLUME) control (press)

DECK B AUTO LOOP (LOOP MOVE/SAMPLE VOLUME) control (turn)

DECK A SELECT button — Note C#1 Note F6 CC 050 — — — OFF=0, ON=127 DECK B SELECT button — Note D1 Note F#6 CC 051 — — — OFF=0, ON=127

DECK A HOT CUE1 button

Hot cue/sampler section

DECK B HOT CUE1 button

DECK A HOT CUE2 button

DECK B HOT CUE2 button

DECK A HOT CUE3 button

DECK B HOT CUE3 button

DECK A HOT CUE4 button

DECK B HOT CUE4 button

DECK A ACTIVE button

DECK B ACTIVE button

MIDI assignment

Section

function

Hot cue function Note A0 Note C#6 CC 044 — — —

Sampler function Note A#0 Note D6 CC 046 — — —

Hot cue function CC 009 CC 073 CC 045 — — —

Sampler function CC 010 CC 074 CC 025 — — —

Hot cue function Note B0 Note D#6 CC 047 — — —

Sampler function Note C1 Note E6 CC 049 — — —

Hot cue function CC 011 CC 075 CC 048 — — —

Sampler function CC 012 CC 076 CC 026 — — —

Hot cue function Note D#1 Note G6 CC 052 Note D#1 Note G6 CC 052 OFF=0, ON=127 Sampler function Note E1 Note G#6 Note D3 Note E1 Note G#6 Note D3 OFF=0, ON=127 Hot cue function Note F1 Note A6 CC 053 Note F1 Note A6 CC 053 OFF=0, ON=127 Sampler function Note F#1 Note A#6 Note D#3 Note F#1 Note A#6 Note D#3 OFF=0, ON=127 Hot cue function Note G1 Note B6 CC 054 Note G1 Note B6 CC 054 OFF=0, ON=127 Sampler function Note G#1 Note C7 Note E3 Note G#1 Note C7 Note E3 OFF=0, ON=127 Hot cue function Note A1 Note C#7 CC 055 Note A1 Note C#7 CC 055 OFF=0, ON=127 Sampler function Note A#1 Note D7 Note F3 Note A#1 Note D7 Note F3 OFF=0, ON=127 Hot cue function Note B1 Note D#7 CC 056 Note B1 Note D#7 CC 056 OFF=0, ON=127 Sampler function Note C2 Note E7 Note F#3 Note C2 Note E7 Note F#3 OFF=0, ON=127 Hot cue function Note C#2 Note F7 CC 057 Note C#2 Note F7 CC 057 OFF=0, ON=127 Sampler function Note D2 Note F#7 Note G3 Note D2 Note F#7 Note G3 OFF=0, ON=127 Hot cue function Note D#2 Note G7 CC 058 Note D#2 Note G7 CC 058 OFF=0, ON=127 Sampler function Note E2 Note G#7 Note G#3 Note E2 Note G#7 Note G#3 OFF=0, ON=127 Hot cue function Note F2 Note A7 CC 059 Note F2 Note A7 CC 059 OFF=0, ON=127 Sampler function Note F#2 Note A#7 Note A3 Note F#2 Note A#7 Note A3 OFF=0, ON=127 Hot cue function Note G2 Note B7 Note A#3 Note G2 Note B7 Note A#3 OFF=0, ON=127 Sampler function Note G#2 Note C8 Note B3 Note G#2 Note C8 Note B3 OFF=0, ON=127 Hot cue function Note A2 Note C#8 Note C4 Note A2 Note C#8 Note C4 OFF=0, ON=127 Sampler function Note A#2 Note D8 Note C#4 Note A#2 Note D8 Note C#4 OFF=0, ON=127

(this unit d computer)

SHIFT OFF SHIFT ON

ADVANCED

SHIFT

MIDI assignment

(computer d this unit)

SHIFT OFF SHIFT ON

ADVANCED

SHIFT

Transmitted data

OFF=0, ON=127

Turn clockwise: 0 – +30 / Turn counterclockwise: -1 – -30

OFF=0, ON=127

Turn clockwise: 0 – +30 / Turn counterclockwise: -1 – -30

English

Additional information

Troubleshooting

! Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this component, check the points below. Sometimes the

trouble may lie in another component. Inspect the other components and electrical appliances being used. If the trouble cannot be rectified after checking the items below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.

! The player may not operate properly due to static electricity or other external influences. In such cases, normal operation may be restored by unplugging the power cord

then plugging it back in.

Problem Check Remedy

The power is not turned on. Is the power cord properly connected? Plug in the power cord to an AC outlet. This unit is not recognized. Is the [ON/OFF] switch for power supply set to [ON]? Set the [ON/OFF] switch for power supply to [ON].

Is the included USB cable properly connected? Connect the included USB cable properly. (page 11) Is [CTRL] lit in TRAKTOR? Press any button other than one in this unit’s mixer section and check that [CTRL] lights in

— Check that [Pioneer. DJM-T1] is selected at [Preferences] > [Controller Manager] >

Music files cannot be played. Are the music files damaged? Play music files that are not damaged. No tracks are displayed in the [TRACK] area. Have the music files been properly imported? Import the music files properly. (page 14)

Have you selected a [Playlists] or [FAVORITES] slot that does not contain any tracks?

Volume of device connected to [AUX IN] terminals is low.

Distorted sound. Are the [MAIN VOL] and [GAIN] controls of TRAKTOR set

Sound being played is interrupted. Are the included power cord and the included USB cable

Sound of an external device or microphone cannot be output.

No sound is produced. Are the connection cables properly connected? Connect the connection cables properly. (page 11)

No sound or small sound. Is the [CD, PHONO, USB] input selector switch set to the

BPM or overall waveform is not displayed. Has the music file been analyzed? Put a check at [Preferences] > [File Management] >

[SYNC] function does not work. Have the music files been properly imported? Reimport the music files and load them in the decks. (page 14)

[SYNC] function does not work even when files are analyzed.

Deck area display is small. — Double-click the track information display section (the part where the track name, BPM, etc.,

[SINGLE/GROUP] selector button does not work.

Is the [LEVEL] control on the front panel set to the proper position?

to the proper positions? Is the audio level being input to the [AUX IN] and [MIC]

terminals set to a suitable level? Is the sound level output from the [MASTER] channel

appropriately set?

Is the level of audio input to each channel properly set? Adjust the [TRIM] control so that the channel level indicator lights at about [0 dB] at the peak

properly connected?

Is the audio latency value suitable? When using Windows, open the [ASIO] tab in the settings utility and set the audio latency to

Is the [INPUT SELECT] switch on the front panel set to the [OFF] position?

Is the included USB cable properly connected? Connect the computer and this unit directly using the included USB cable. USB hubs cannot

Are terminals or plugs dirty? Wipe any dirt off terminals and plugs before connecting. Is the [UTILITY (WAKE UP)] button’s indicator flashing at

4-second intervals? Are [Audio Setup], [Output Routing] and

[Input Routing] in TRAKTOR properly set?

Are the connected components and amplifiers properly set?

proper position? Is [MASTER ATT.] set to [–6 dB]? Set [MASTER ATT.] to [0 dB]. (page 11)

Has the music file been analyzed? If music files cannot be analyzed automatically, input the [Beat Grid] manually. Is [BEAT MARKER (Grid)] set for hot cue? Set at least one [BEAT MARKER] to [Grid].

— The [Single] mode cannot be selected with TRAKTOR SCRATCH DUO 2.

TRAKTOR.

[Device Setup] > [Device]. (page 25)

Select a [Playlists] or [FAVORITES] slot that contains tracks.

Adjust the [LEVEL] control on the front panel according to the connected device. (page 23)

Adjust the [MAIN VOL] and [GAIN] controls while watching the [MAIN] level indicator in TRAKTOR.

Set the audio level input to the terminals to a suitable level for the connected devices.

Adjust the [MASTER LEVEL] control so that the master channel level indicator lights at around [0 dB] at the peak level. (page 17)

If the sound is distorted even when the [MASTER LEVEL] control is adjusted, set [MASTER ATT.] to [–6 dB]. (page 11)

level. (page 17) The sound will be interrupted if the included power cord or the included USB cable is discon-

nected from the main unit during playback. Properly fasten the included USB cable to the cord hook on the main unit. (page 11)

a suitable value. (page 26) When using a Macintosh computer, set [Preferences] > [Audio Setup] > [Latency] in TRAKTOR to a suitable value.

Set the [INPUT SELECT] switch to the [AUX] position when using an external device, to the [MIC] position when using a microphone. (page 23)

be used. (page 11)

Install the driver software properly on the computer. (page 9)

Check that [Preferences] is set as shown below. (Page 25) [Audio Setup] > [Audio Device] > [PIONEER DJM-T1 (Core Audio)] (Mac OS X) or [PIONEER DJM-T1 ASIO (ASIO)] (Windows) [Output Routing] > [Output Deck A] [L] > [1.PIONEER DJM-T1 OUT 1] and [R] > [2.PIONEER DJM-T1 OUT 2] [Output Routing] > [Output Deck B] [L] > [3.PIONEER DJM-T1 OUT 3] and [R] > [4.PIONEER DJM-T1 OUT 4] [Input Routing] > [Input Deck A] [L(Mono)] > [1.PIONEER DJM-T1 IN 1] and [R] > [2.PIONEER DJM-T1 IN 2] [Input Routing] > [Input Deck B] [L(Mono)] > [3.PIONEER DJM-T1 IN 3] and [R] > [4.PIONEER DJM-T1 IN 4] When using Mac OS X, replace the numbers following [X.PIONEER DJM-T1 OUT] and [X.PIONEER DJM-T1 IN] above with numbers [0] to [3] when making the settings.

Set the external input selection and volume on the components and amplifiers properly.

Switch the [CD, PHONO, USB] input selector switch and switch the channel’s input source. (page 17)

[Analyze new tracks when loading into deck], then reload the track in the deck.

Put a check at [Preferences] > [File Management] > [Set Beat-Grid when detecting BPM], then reload the track in the deck.

are displayed) in the deck area.

If you upgrade to TRAKTOR SCRATCH PRO 2, the effect panel can be switched to the [Single] mode.

+ 70 hidden pages