Thank you for buying this Pioneer product.
Please read through these operating instructions so you
will know how to operate your model properly.
After you have finished reading the instructions, put them
away in a safe place for future reference.
CAUTION: This product satisfies FCC regulations when
shielded cables and connectors are used to connect the unit to
other equipment. To prevent electromagnetic interference with
electric appliances such as radios and televisions, use shielded
cables and connectors for connections.
IMPORTANT NOTICE:
RECORD THE MODEL NUMBER AND SERIAL NUMBER
OF THIS EQUIPMENT BELOW. THE NUMBERS ARE ON
THE REAR PANEL.
MODEL NO.DJM-500
SERIAL NO.
KEEP THESE NUMBERS FOR FUTURE USE.
IMPORTANT
The lightning flash with arrowhead, within an equilateral
triangle, is intended to alert the user to the presence of
uninsulated "dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
SAFETY INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
READ INSTRUCTIONS – All the safety and operating
instructions should be read before the appliance is
operated.
RETAIN INSTRUCTIONS – The safety and operating
instructions should be retained for future
reference.
HEED WARNING – All warnings on the appliance and
in the operating instructions should be adhered to.
FOLLOW INSTRUCTIONS – All operating and use in-
structions should be followed.
WATER AND MOISTURE – The appliance should not
be used near water – for example, near a bathtub,
washbowl, kitchen sink, laundry tub, in a wet
basement, or near a swimming pool, etc.
LOCATION – The appliance should be installed in a
stable location.
WALL OR CEILING MOUNTING – The appliance
should not be mounted to a wall or ceiling.
VENTILATION – The appliance should be situated so
that its location or position does not interfere with
its proper ventilation. For example, the appliance
should not be situated on a bed, sofa, rug, or
similar surface that may block the ventilation
openings; or, placed in a built-in installation, such
as a bookcase or cabinet that may impede the
flow of air through the ventilation openings.
HEAT – The appliance should be situated away from
heat sources such as radiators, heat registers,
stoves, or other appliances (including amplifiers)
that produce heat.
POWER SOURCES – The appliance should be con-
nected to a power supply only of the type described in the operating instructions or as marked
on the appliance.
POWER-CORD PROTECTION – Power-supply cords
should be routed so that they are not likely to be
walked on or pinched by items placed upon or
against them. Pay particular attention to cords at
plugs, convenience receptacles, and the point
where they exit from the appliance.
GROUNDING-TYPE PLUG – This product is equipped
with a three-wire grounding-type plug, a plug
having a third (grounding) pin.
This plug will only fit into a grounding-type power
outlet. This is a safety feature. If you are unable to
insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the grounding-type
plug.
CLEANING – The appliance should be cleaned only
with a polishing cloth or a soft dry cloth. Never
clean with furniture wax, benzine, insecticides or
other volatile liquids since they may corrode the
cabinet.
POWER LINES – An outdoor antenna should be located
away from power lines.
NONUSE PERIODS – The power cord of the appliance
should be unplugged from the outlet when left unused for a long period of time.
OBJECT AND LIQUID ENTRY – Care should be taken
so that objects do not fall and liquids are not spilled
into the enclosure through openings.
DAMAGE REQUIRING SERVICE – The appliance
should be serviced by a Pioneer authorized service
center or qualified service personnel when:
÷ The power-supply cord or the plug has been
damaged.
÷ Objects have fallen, or liquid has been spilled into
the appliance.
÷ The appliance has been exposed to rain.
÷ The appliance does not appear to operate normally
or exhibits a marked change in performance.
÷ The appliance has been dropped or the enclosure
damaged.
SERVICING – The user should not attempt to service
the appliance beyond that described in the
operating instructions. All other servicing should
be referred to qualified service personnel.
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
GROUND CLAMPS
POWER SERVICE GROUNDING
FIG. A
ELECTRODE SYSTEM
(NEC ART 250, PART H)
OUTDOOR ANTENNA GROUNDING – If an outside
antenna is connected to the antenna terminal, be
sure the antenna system is grounded so as to
provide some protection against voltage surges
and built-up static charges.
In the U.S.A. section 810 of the National Electrical
Code, ANSI/NFPA 70, provides information with
respect to proper grounding of the mast and
supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit,
connection to grounding electrodes, and
requirements for the grounding electrode. See
Fig. A.
CART – An appliance and cart combination should be
moved with care. Quick stops, excessive force,
and uneven surfaces may cause the appliance and
cart combination to overturn.
NEC – NATIONAL ELECTRIC CODE
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810 – 20)
GROUNDING CONDUCTORS
(NEC SECTION 810 – 21)
[For Canadian model]
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
[Pour le modèle Canadien]
Cet appareil numerique de la Classe B respecte toutes les exigences du Reglement sur le material brouilleur du Canada.
Information to User
Alteration or modifications carried out without appropriate authorization may invalidate the user's right to operate the
equipment.
2
<DRB1192>
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
•
A
S
S
O
C
I
A
T
I
O
N
•
E
L
E
C
T
R
O
N
I
C
I
N
D
U
S
T
R
I
E
S
EST 1924
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
I
N
C
I
D
N
U
O
S
R
T
T
R
C
I
E
E
S
L
E
•
•
EST 1924
A
N
S
O
S
I
O
T
C
A
I
We
Want You
LISTENING
For A Lifetime
We Want You Listening For A Lifetime
Used wisely, your new sound equipment will provide a lifetime of
fun and enjoyment. Since hearing damage from loud noise is often
undetectable until it is too late, this manufacturer and the Electronic
Industries Association’s Consumer Electronics Group recommend
you avoid prolonged exposure to excessive noise. This list of sound
levels is included for your protection.
Selecting fine audio equipment such as the unit you’ve just
purchased is only the start of your musical enjoyment. Now it’s time
to consider how you can maximize the fun and excitement your
equipment offers. This manufacturer and the Electronic Industries
Association’s Consumer Electronics Group want you to get the most
out of your equipment by playing it at a safe level. One that lets the
sound come through loud and clear without annoying blaring or
distortion-and, most importantly, without affecting your sensitive
hearing.
Sound can be deceiving. Over time your hearing “comfort level”
adapts to higher volumes of sound. So what sounds “normal” can
actually be loud and harmful to your hearing. Guard against this by
setting your equipment at a safe level BEFORE your hearing adapts.
To establish a safe level:
÷ Start your volume control at a low setting.
÷ Slowly increase the sound until you can hear it comfortably and
clearly, and without distortion.
Decibel
LevelExample
30Quiet library, soft whispers
40Living room, refrigerator, bedroom away from traffic
50Light traffic, normal conversation, quiet office
60Air conditioner at 20 feet, sewing machine
70Vacuum cleaner, hair dryer, noisy restaurant
80Average city traffic, garbage disposals, alarm clock
at two feet.
THE FOLLOWING NOISES CAN BE DANGEROUS
UNDER CONSTANT EXPOSURE
90Subway, motorcycle, truck traffic, lawn mower
100Garbage truck, chain saw, pneumatic drill
120Rock band concert in front of speakers, thunderclap
140Gunshot blast, jet plane
180Rocket launching pad
Information courtesy of the Deafness Research Foundation.
Once you have established a comfortable sound level:
÷ Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing
damage or loss in the future. After all, we want you listening for a
lifetime.
We
Want You
LISTENING
For A Lifetime
<DRB1192>
3
CAUTIONS REGARDING HANDLING
CHECKING ACCESSORIES
Location
Install the unit in a well-ventilated location where it will
not be exposed to high temperatures or humidity.
Do not install the unit in a location which is exposed to
direct rays of the sun, or near stoves or radiators. Excessive heat can adversely affect the cabinet and internal components. Installation of the unit in a damp or dusty environment may also result in a malfunction or accident. (Avoid
installation near cookers etc., where the unit may be exposed to oily smoke, steam or heat.)
Condensation
When this unit is brought into a warm room from previously cold surroundings or when the room temperature
rises sharply, condensation may form inside, and the unit
may not be able to attain its full performance. In cases like
this, allow the unit to stand for about an hour or raise the
room temperature gradually.
Cleaning the unit
• Use a polishing cloth to wipe off dust and dirt.
• When the surfaces are very dirty, wipe with a soft cloth
dipped in some neutral cleanser diluted five or six times
with water and wrung out well, then wipe again with a
dry cloth. Do not use furniture wax or cleaners.
• Never use thinners, benzene, insecticide sprays or other
chemicals on or near this unit, since these will corrode
the surfaces.
• Power cord
• Short-circuit pin plug (four)
These are inserted in the PHONO 1 and PHONO 2 terminals at the rear.
• Operating instructions
4
<DRB1192>
FEATURES
BPM Counter
The auto BPM counter provided allows the tempo of songs
to be checked visually. This counter can be switched between real-time and average.
BPM Level Display (Beat meter display)
Displays the level of sound components determining the
BPM.
The beat can be checked visually.
Peak Level Meter
The peak level meter provided is equipped with 15-bit LED
indicators for all channels. This meter can be switched between BPM and peak.
Fader Start
The CD player can be started by increasing the level of the
cross fader or channel fader, which is selected using the
cross fader switch. (This function can be used only when
the Pioneer CD player CDJ-500 series is connected.)
3-Band Equalizer & Kill
A 3-band equalizer corresponding to the HI, MID, and LOW
channels. The attenuation level also serves as a kill function which can decrease the level to –20 dB.
Digital Display of Effector
Loads the master tempo incorporated in Pioneer CD players. Key changes by the rotary type linear control can give
new performance effects to the mixer.
Variety of Effects
Both external effects and internal effects can be imposed
on all channels, the microphone, and master.
A variety of effects such as delay, echo, auto pan, flanger,
reverb, and pitch shifter can be enjoyed.
Enhanced Input/Output Terminals
In addition to the 9 inputs, 2 CD and 2 LINE systems, 3
PHONO (for MM only) systems, and 2 microphone systems,
three outputs including the pro-specifications XLR output,
and booth monitor output are provided independently.
SEND/RETURN terminals are also provided for the external effectors.
<DRB1192>
5
CONNECTIONS
When connecting the units or changing their connections,
be sure to turn off the power switch and disconnect the
power cord from the outlet.
1. Connection of Input Equipment
DAT, etc.
~AC IN
R
MASTER
OUT 1
L
R
CD2
CD1
CDJ-500G/
CDJ-500
Control cord
Can be connected to CDJ-
L
R
L
L
R
CH - 3
LINEPHONO 2
R
MASTER OUT 3
R
SIGNAL
GND
L
R
L
MASTER
LEVEL
ATT.
CH - 4
PHONO 3
L
R
L
BOOTH
MONITOR
MASTER
OUT 2
L
R
L
R
CH - 2
CD 2/ LINEPHONO 1
RL
SEND
R
CH - 1
L
R
CH - 2
PLAYER CONTROL
RL
(MONO)
RETURN
L
L
R
CD 1LINE
CH - 1
(MONO)
R
500G and CDJ-500 .
CH - 4
SUBMIC
L
DJM-500
AC 120V, 60Hz
Player 3
Player 2
To connect the analog player, remove the short-circuit pin
plugs (four) inserted in the PHONO terminals (PHONO 1,
PHONO 2) of CH2 and CH3. These short-circuit pin plugs
serve to cut fine noises to provide high performance when
not connecting the analog player. Be sure to keep them
carefully after removal. When removed for connecting the
analog player, insert them back as before after use.
6
<DRB1192>
Player 1
Cassette deck, etc.
Connecting audio cords
Use cords with red and white pin plugs.
Connect the white plug to (L) and the red plug to (R). Be
sure to insert completely.
L
R
White plug
Red plug
Loading...
+ 14 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.