Pioneer DEH-P800PRS User Manual

Note:

• This unit is for vehicles with a 12-volt battery and
negative grounding. Before installing it in a recre­ational vehicle, truck, or bus, check the battery
voltage.

• To avoid shorts in the electrical system, be sure to
disconnect the ≠ battery cable before beginning
installation.

• Refer to the owner’s manual for details on con­necting the power amp and other units, then make
connections correctly.

• Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.

• Route and secure all wiring so it cannot touch any
moving parts, such as the gear shift, handbrake and
seat rails. Do not route wiring in places that get hot,
such as near the heater outlet. If the insulation of
the wiring melts or gets torn, there is a danger of
the wiring short-circuiting to the vehicle body.

• Don’t pass the yellow lead through a hole into the
engine compartment to connect to the battery.
This will damage the lead insulation and cause a
very dangerous short.

• Do not shorten any leads. If you do, the protection
circuit may fail to work when it should.

• Never feed power to other equipment by cutting
the insulation of the power supply lead of the unit
and tapping into the lead. The current capacity of
the lead will be exceeded, causing overheating.

• When replacing the fuse, be sure to only use a
fuse of the rating prescribed on the fuse holder.

• Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded
or the left and right ≠ speaker leads are common.

• If the RCA pin jack on the unit will not be used,
do not remove the caps attached to the end of the
connector.

• Speakers connected to this unit must be high­power with minimum rating of 50 W and imped­ance of 4 to 8 ohms. Connecting speakers with
output and/or impedance values other than those
noted here may result in the speakers catching
fire, emitting smoke or becoming damaged.

• When connecting tweeters, please confirm the
tweeter’s usable frequency range. When you set
the cut-off frequency, set higher than the lowest
usable frequency of the tweeter.

• Auto TA uses higher range than 10 kHz for mea­surement. Therefore, using the tweeter that cannot
reproduce 10 kHz frequency range may damage
the tweeter. When Auto TA&EQ is operated, be
sure to set the appropriate cut-off frequency. Also,
use the tweeter that can reproduce 10 kHz at the
lowest usable frequency.

• When this product’s source is switched ON, a
control signal is output through the blue/white
lead. Connect to an external power amp’s system
remote control or the car’s Auto-antenna relay
control terminal (max. 300 mA 12 V DC). If the
car features a glass antenna, connect to the anten­na booster power supply terminal.

• When an external power amp is being used with
this system, be sure not to connect the blue/white
lead to the amp’s power terminal. Likewise, do
not connect the blue/white lead to the power ter­minal of the auto-antenna. Such connection could
cause excessive current drain and malfunction.

• To avoid a short-circuit, cover the disconnected
lead with insulating tape. Insulate the unused
speaker leads without fail. There is a possibility of
a short-circuit if the leads are not insulated.

• To prevent incorrect connection, the input side of
the IP-BUS connector is blue, and the output side
is black. Connect the connectors of the same col­ors correctly.

• If this unit is installed in a vehicle that does not
have an ACC (accessory) position on the ignition
switch, the red lead of the unit should be connect­ed to a terminal coupled with ignition switch
ON/OFF operations. If this is not done, the vehi­cle battery may be drained when you are away
from the vehicle for several hours. (Fig. 1)

Fig. 1

• The black lead is ground. Please ground this lead
separately from the ground of high-current prod­ucts such as power amps.
If you ground the products together and the
ground becomes detached, there is a risk of dam­age to the products or fire.

No ACC positionACC position

INSTALLATION MANUAL

MANUEL D’INSTALLATION

<KMMZX> <07J00000>

DEH-P800PRS

Printed in Thailand
Imprimé en Thaïlande

<CRD4266-A/N> UC

Connecting the Units <ENGLISH>

Fig. 2

Power cable connection diagram

C

C

A

O

F

N

F

O

S

T

A

R

T

O

F

N

F

O

S

T

A

R

T

15 cm
(5-7/8 in.)

Antenna jack

Yellow/black
If you use an equipment with Mute
function, wire this lead to the Audio
Mute lead on that equipment.
If not, keep the Audio Mute lead free of
any connections.

Translucent with yellow stripe
To terminal always supplied with
power regardless of ignition switch
position.

Red
To electric terminal controlled by
ignition switch (12 V DC) ON/OFF.

Orange/white
To lighting switch terminal.

Black (ground)
To vehicle (metal) body.

This product

Fuse holder
(10 A)

Fuse resistor

Fuse resistor

RCA cable connector
(Refer to Fig. 3 to 6.)

IP-BUS input
(Blue)

IP-BUS cable

Front speaker

Middle range speaker

Rear speaker

High range speaker

Jack for the Wired Remote Control Adaptors
Please see the Instruction Manual for the
Wired Remote Control Adaptors (sold separately).

Multi-CD player
(sold separately)

Blue/white
To system control terminal of the power amp or
Auto-antenna relay control terminal (max. 300
mA 12 V DC).

Speaker leads
(For more details, refer to Fig. 3 to 6.)

Left Right

or

or

+

≠

+

≠

FL +

FL –

RL +

RL –

FR +

FR –

RR +

RR –

With a 2 speaker system, do not
connect anything to the speaker leads
that are not connected to speakers.

+

≠

Middle range speaker

+

≠

High range speaker

Front speaker

Rear speaker

or

or

Connecting the Units <ENGLISH>

h

the

ustration

belo

.

S

h

the

ustration

belo

.

Fig. 3 Fig. 4

Connection diagram for standard mode with internal amp Connection diagram for standard mode without internal amp

Note:

• If using this system, we recommend that this unit’s internal amp is turned off.
For more details, refer to operation manual.

Antenna jack

This product

DSP switch
Switc
ill

23 cm (9 in.)

DSPswitch as

w

Subwoofer output
(LOW/SUBWOOFER
OUTPUT)

Connecting cords with RCA pin
plugs (sold separately)

Power amp

(sold separately)

Antenna jack

This product

DSP switch

witc

ill

23 cm (9 in.)

15 cm (5-7/8 in.)

15 cm (5-7/8 in.)

DSPswitch as

w

Subwoofer output
(LOW/SUBWOOFER
OUTPUT)

Rear output
(HIGH/REAR OUTPUT)

Front output
(MID/FRONT OUTPUT)

Connecting cords with RCA pin
plugs (sold separately)

Power amp

(sold separately)

Power amp

(sold separately)

Power amp

(sold separately)

System remote control

Left

Front speaker

Rear speaker

Subwoofer

+

≠

+

≠

+

≠

+

≠

+

≠

+

≠

Right

Front speaker

Rear speaker

Subwoofer

Power cable
(For details, refer to Fig. 2.)

Left Right

Front speaker

Rear speaker Rear speaker

+

≠

+

≠

FL +

FL –

RL +

RL –

FR +

FR –

RR +

RR –

+

≠

+

≠

Front speaker

System remote control

Blue/white
To system control terminal of the power amp or
Auto-antenna relay control terminal (max. 300
mA 12 V DC).

Subwoofer

Perform this connection when using the optional amplifier.

+

≠

+

≠

Subwoofer

Power cable
(For details, refer to Fig. 2.)

FL +

FL –
RL +

RL –

Blue/white
To system control terminal of the power amp or
Auto-antenna relay control terminal (max. 300

mA 12 V DC).
Speaker leads
Not used.

FR +

FR –

RR +

RR –

Connecting the Units <ENGLISH>

h

the

ustration

belo

.

Connection diagram for 3-way network mode with internal amp

Fig. 5

ustration

belo

.

Connection diagram for 3-way network mode without internal amp

Note:

• If using this system, we recommend that this unit’s internal amp is turned off.
For more details, refer to operation manual.

Fig. 6

Antenna jack

This product

Power cable
(For details, refer to Fig. 2.)

Left Right

Middle range speaker

High range speaker High range speaker

+

≠

+

≠

FL +

FL –

RL +

RL –

FR +

FR –

RR +

RR –

DSP switch
Switc
ill

+

≠

+

≠

23 cm (9 in.)

DSPswitch as

w

Middle range speaker

Connecting cords with RCA pin
plugs (sold separately)

Low range output
(LOW/SUBWOOFER
OUTPUT)

System remote control

Blue/white
To system control terminal of the power amp or
Auto-antenna relay control terminal (max. 300
mA 12 V DC).

Left Right

Low range speaker

Perform this connection when using the optional amplifier.

+

≠

+

Low range speaker

≠

Power amp

(sold separately)

Antenna jack

This product

Power cable
(For details, refer to Fig. 2.)

FL +

FL –
RL +

RL –

Speaker leads
Not used.

RR +

DSP switch

SwitchtheDSPswitch as

ill

Blue/white
To system control terminal of the power amp or
Auto-antenna relay control terminal (max. 300
mA 12 V DC).

FR +

FR –

RR –

23 cm (9 in.)

15 cm (5-7/8 in.)

15 cm (5-7/8 in.)

w

Low range output
(LOW/SUBWOOFER
OUTPUT)

High range output
(HIGH/REAR OUTPUT)

Middle range output
(MID/FRONT OUTPUT)

System remote control

Left

Middle range speaker

High range speaker

Connecting cords with RCA pin
plugs (sold separately)

Power amp

(sold separately)

+

≠

+

≠

+

≠

Right

+

Middle range speaker

≠

+

High range speaker

≠

+

Low range speakerLow range speaker

≠

Power amp

(sold separately)

Power amp

(sold separately)