Pioneer DEH-34UB, DEH-3400UB, DEH-2400UB, DEH-24UB User Manual 2

CD RDS RECEIVER AUTORADIO CD RDS REPRODUCTOR DE CD CON RECEPTOR RDS

DEH-3400UB DEH-2400UB DEH-34UB DEH-24UB

English EspañolFrançais

Owner’s Manual

Mode d’emploi

Manual de instrucciones

Section

Before you start

Thank you for purchasing this PIONEER product

To ensureproperuse,please read through this manual before using this product. It is especially important that you read and obser ve WARN-

INGs and CAUTIONs in this manual. Please keep the manual in a safe and accessible place for future reference.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Information to User

Alteration or modifications carried out without appropriate authorization may invalidate the user ’s right to operate the equipment.

Note

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

The Safety of Your Ears is in Your Hands

Get the most out of your equipment by playing it at a safe level—a level that lets the sound come through clearly without annoying blaring or distortion and, most importantly, without affecting your sensitive hearing. Sound can be deceiving. Over time, your hearing “comfort level” adapts to higher volumes of sound, so what sounds “normal” can actually be loud and harmful to your hearing. Guard against this by setting your equipment at a safe level BEFORE your hearing adapts.

ESTABLISH A SAFE LEVEL:

! Set your volume control at a low setting. ! Slowly increase the sound until you can hear

it comfortably and clearly, without distortion.

! Once you have established a comfortable

sound level, set the dial and leave it there.

BE SURE TO OBSERVE THE FOLLOWING GUIDELINES:

! Do not turn up the volume so high that you

can’t hear what’s around you.

! Use caution or temporarily discontinue use

in potentially hazardous situations.

! Do not use headphones while operating a

motorized vehicle; the use of headphones may create a traffic hazard and is illegal in many areas.

About this unit

The tuner frequencies on this unit are allocated for use in North America. Use in other areas may result in poor reception.

WARNING

Handling the cord on this product or cords associated with accessories sold with the product may expose you to chemicals listed on proposition 65 known to the State of California and other governmental entities to cause cancer and birth defect or other reproductive harm. Wash

hands after handling.

CAUTION: USE OF CONTROL OR ADJUSTMENT OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. CAUTION: THE USE OF OPTICAL INSTRUMENTS WITH THIS PRODUCT WILL INCREASE EYE HAZARD.

CAUTION

! Do not allow this unit to come into contact

with liquids. Electrical shock could result. Also, damage to this unit, smoke, and overheating could result from contact with liquids.

! Always keep the volume low enough to hear

outside sounds.

! Avoid exposure to moisture. ! If the battery is disconnected or discharged,

any preset memory will be erased.

Important (Serial number)

The serial number is located on the bottom of this unit. For your own security and convenience, be sure to record this number on the enclosed warranty card.

Note

Function setting operations are completed even if the menu is cancelled before the operations are confirmed.

About this manual

! In the following instructions, USB memories

and USB audio players are collectively referred to as “USB storage device”.

! In this manual, iPod and iPhone will be re-

ferred to as “iPod”.

Demo mode

Important

! Failure to connect the red lead (ACC) of this

unit to a terminal coupled with ignition switch on/off operations may lead to battery drain.

! Remember that if the feature demo contin-

ues operating when the car engine is turned off, it may drain battery power.

The demo starts automatically if you do not operate this unit within about 30 seconds since the unit was last operated or if the ignition switch is set to ACC or ON while the unit is turned off. To cancel the demo mode, you need to display the initial settings. Select DEMO (demo display set- ting) and turn off the demo display. For details, refer to Initial settings on page 9.

b c dea87

Before you start

Operating this unit

Section

After-sales service for Pioneer products

Please contact the dealer or distributor from where you purchased this unit for after-sales service (including warranty conditions) or any other information. In case the necessary information is not available, please contact the companies listed below: Please do not ship your unit to the companies at the addresses listed below for repair without advance contact.

U.S.A.

Pioneer Electronics (USA) Inc. CUSTOMER SUPPORT DIVISION P.O. Box 1760 Long Beach, CA 90801-1760 800-421-1404

CANADA

Pioneer Electronics of Canada, Inc. CUSTOMER SATISFACTION DEPARTMENT 340 Ferrier Street Unit 2 Markham, Ontario L3R 2Z5, Canada 1-877-283-5901 905-479-4411

For warranty information please see the Limited Warranty sheet included with this unit.

In case of trouble

Should this unit fail to operate properly, please contact your dealer or nearest authorized PIONEER Service Station.

Visit our website

http://www.pioneerelectronics.com

in Canada

http://www.pioneerelectronics.ca

! Learn about product updates (such as firm-

ware updates) for your product.

! Register your product to receive notices

about product updates and to safeguard purchase details in our files in the event of loss or theft.

! Access owner ’s manuals, spare parts infor-

mation, service information, and much more.

Head unit

DEH-3400UB and DEH-34UB

12 3 4 5 6

Part Part

1 h (eject) 8

(list) 9 c/d

MULTI-CONTROL

(M.C.)

4 SRC/OFF b 1 to 6

5 Disc loading slot c

6 USB port d

(color) e Detach button

DEH-2400UB and DEH-24UB

12 3 4 5 6

Part Part

1 h (eject) 8

(list) 9 c/d

(back/display)

(iPod

BAND/ control)

(clock)

AUX input jack (3.5 mm stereo jack)

(back/display)

Part Part

MULTI-CONTROL

(M.C.)

4 SRC/OFF b 1 to 6

5 Disc loading slot c

6 USB port d

CAUTION

! Use an optional Pioneer USB cable (CD-

U50E) to connect the USB audio player/USB memory as any device connected directly to the unit will protrude out from the unit and may be dangerous.

! Do not use unauthorized products.

BAND/

e Detach button

(iPod

control)

(clock)

AUX input jack (3.5 mm stereo jack)

Remote control

9 a m l

4 k

Part Operation

f VOLUME

g MUTE

Press to increase or decrease volume.

Press to mute. Press again to unmute.

g h i

English

2 4

Section

Operating this unit

h a/b

i AUDIO

j DISP/SCRL

k e

Display indication

Part Operation

Press to recall preset stations. Press to select the next/previous folder.

Press to select an audio function.

Press to select different displays. Press and hold to turn dimmer on or off.

Press to pause or resume playback.

FUNCTION

LIST/ ENTER

Press to select functions.

Press to display the disc title, track title, folder, or file list depending on the source. Press to display the list depending on the source. While in the operating menu, press to control functions.

Indicator State

Main dis-

play section

3 LOC Local seek tuning is on.

peat)

dom/shuf-

fle)

(sound re-

triever)

control)

! Tuner: band and frequency ! Built-in CD, USB storage

device and iPod: elapsed playback time and text information

The list function is being oper-

(list)

ated.

(re-

Track or folder repeat is on.

Random play is on.

(ran-

The iPod source is selected and the shuffle or shuffle all function is on.

The sound retriever function is on.

(iPod

This unit’s iPod function is operated from your iPod.

If you select NO, you cannot set up in the set up menu.

3 Perform the following procedures to set the menu.

To proceed to the next menu option, you need to confirm your selection.

CLOCK SET (setting the clock)

1 Turn M.C. to adjust hour. 2 Press M.C. to select minute. 3 Turn M.C. to adjust minute. 4 Press M.C. to confirm the selection.

DEMO (demo display setting)

1 Turn M.C. to set the demo display to on or off. 2 Press M.C. to confirm the selection.

QUIT appears.

4 To finish your settings, turn M.C. to select YES. Press to select.

# If you prefer to change your setting again, turn

M.C. to switch to NO. Press to select.

! To avoid damaging the device or vehicle inte-

rior, remove any cables and devices attached to the front panel before detaching it.

Removing the front panel to protect your unit from theft 1 Press the detach button to release the front

panel.

2 Push the front panel upward (M) and then pull

it toward (N) you.

3 Always keep the detached front panel in a pro-

tection device such as a protection case.

Re-attaching the front panel 1 Slide the front panel to the left.

Make sure to insert the tabs on the left side of the head unit into the slots on the front panel.

Notes

Set up menu

When you turn the ignition switch to ON after installation, set up menu appears on the display. You can set up the menu options below.

1 After installation of this unit, turn the

65 73

ignition switch to ON. SET UP appears.

2 Turn M.C. to switch to YES. Press M.C. to select.

# If you do not operate for 30 seconds, the set up menu will not be displayed. # If you prefer not to set up at this time, turn M.C. to switch to NO. Press to select.

! You can set up the menu options in the initial

settings. For details about the settings, refer to Initial settings on page 9.

! You can cancel set up menu by pressing

SRC/OFF.

Basic operations

Important

! Handle gently when removing or attaching

the front panel.

! Avoid subjecting the front panel to excessive

shock.

! Keep the front panel out of direct sunlight

and high temperatures.

2 Press the right side of the front panel until it is

firmly seated. If you cannot attach the front panel to the head unit successfully, make sure that you are placing the front panel onto the head unit correctly. Forcing the front panel into place may result in damage to the front panel or head unit.

Turning the unit on 1 Press SRC/OFF to turn the unit on.

Turning the unit off 1 Press and hold SRC/OFF until the unit turns

off.

Operating this unit

Section

Selecting a source

1 Press SRC/OFF to cycle between:

TUNER (tuner)—CD (built-in CD player)—USB

(USB)/iPod (iPod)—AUX (AUX)

Adjusting the volume 1 Turn M.C. to adjust the volume.

CAUTION

For safety reasons, park your vehicle when removing the front panel.

Note

When this unit’s blue/white lead is connected to the vehicle’s auto-antenna relay control terminal, the vehicle’s antenna extends when this unit’s source is turned on. To retract the antenna, turn the source off.

Use and care of the remote control

Using the remote control 1 Point the remote control in the direction of the

front panel to operate. When using for the first time, pull out the film protruding from the tray.

Replacing the battery 1 Slide the tray out on the back of the remote

control.

2 Insert the battery with the plus (+) and minus

(–) poles aligned properly.

WARNING

! Keep the battery out of the reach of children.

Should the battery be swallowed, consult a doctor immediately.

! Batteries (battery pack or batteries installed)

must not be exposed to excessive heat such as sunshine, fire or the like.

CAUTION

! Use one CR2025 (3 V) lithium battery. ! Remove the battery if the remote control is

not used for a month or longer.

! There is a danger of explosion if the battery is

incorrectly replaced. Replace only with the same or equivalent type.

! Do not handle the battery with metallic tools. ! Do not store the battery with metallic ob-

jects.

! If the battery leaks, wipe the remote control

completely clean and install a new battery.

! When disposing of used batteries, comply

with governmental regulations or environmental public institutions’ rules that apply in your country/area.

! “Perchlorate Material – special handling may

apply. See

www.dtsc.ca.gov/hazardouswaste/ perchlorate. (Applicable to California, U.S.A.)”

Important

! Do not store the remote control in high tem-

peratures or direct sunlight.

! The remote control may not function properly

in direct sunlight.

! Do not let the remote control fall onto the

floor, where it may become jammed under the brake or accelerator pedal.

Menu operations identical for set up menu/function settings/audio adjustments/ initial settings/lists

Returning to the previous display Returning to the previous list (the folder one level higher)

1 Press

Returning to the ordinary display Canceling the initial setting menu/set up menu 1 Press BAND/

Returning to the ordinary display from the list 1 Press BAND/

Tuner

Basic operations

Selecting a band

1 Press BAND/

F3 for FM or AM) is displayed.

Recalling preset stations 1 Press c or d. ! If MAN (manual tuning) is selected in SEEK,

you cannot recall preset stations. You need to select PCH (preset channel) in SEEK. For details about the settings, refer to SEEK (left/right key setting) on the next page.

until the desired band (F1, F2,

Manual tuning (step by step) 1 Press c or d. ! If PCH (preset channel) is selected in SEEK,

you cannot tune up or down manually. You need to select MAN (manual tuning) in SEEK. For details about the settings, refer to SEEK (left/right key setting) on the next page.

Seeking 1 Press and hold c or d, and then release.

You can cancel seek tuning by briefly pressing c or d. While pressing and holding c or d, you can skip stations. Seek tuning starts as soon as you release c or d.

Storing and recalling stations for each band

Using preset tuning buttons

1 When you find a station that you want to store in memory, press one of the preset tuning buttons (1 to 6) and hold until the preset number stops flashing.

2 Press one of the preset tuning buttons (1 to 6) to select the desired station.

Switching the display

Selecting the desired text information

1 Press

Program service name/frequency—song title/ artist name—entertainment—frequency

! Depending on the band, text information can

be changed.

! Text information items that can be changed

depend on the area.

English

Function settings

1 Press M.C. to display the main menu.

Section

Operating this unit

2 Turn M.C. to change the menu option and press to select FUNCTION.

3 Turn M.C. to select the function.

After selecting, perform the following procedures to set the function.

BSM (best stations memory)

BSM (best stations memory) automatically stores the six strongest stations in the order of their signal strength. 1 Press M.C. to turn BSM on.

To cancel, press M.C. again.

LOCAL (local seek tuning)

Local seek tuning lets you tune in to only those radio stations with sufficiently strong signals for good reception. 1 Press M.C. to select the desired setting.

FM: OFF—LV 1 —LV2 —LV3 —LV4 AM: OFF—LV 1 —LV2 The highest level setting allows reception of only the strongest stations, while lower levels allow the reception of weaker stations.

SEEK (left/right key setting)

You can assign a function to the left and right keys of the unit. Select MAN (manual tuning) to tune up or down manually or select PCH (preset channel) to switch between preset channels. 1 Press M.C. to select MAN or PCH.

CD/CD-R/CD-RW and USB storage devices

Basic operations

Playing a CD/CD-R/CD-RW 1 Insert the disc into the disc loading slot with

the label side up.

Ejecting a CD/CD-R/CD-RW 1 Press h.

Playing songs on a USB storage device

1 Open the USB port cover. 2 Plug in the USB storage device using a USB

cable. A song will be played automatically.

Stopping playback of files on a USB storage device 1 You may disconnect the USB storage device at

any time. The unit stops playback.

Selecting a folder 1 Press 1/

Selecting a track 1 Press c or d.

Fast forwarding or reversing 1 Press and hold c or d. ! When playing compressed audio, there is no

Returning to root folder 1 Press and hold BAND/

Switching between compressed audio and CD-DA 1 Press BAND/

Switching between playback memory devices You can switch between playback memory devices on USB storage devices with more than one Mass Storage Device-compatible memory device. 1 Press BAND/ ! You can switch between up to 32 different

or 2/ .

sound during fast forward or reverse.

memory devices.

Note

Disconnect USB storage devices from the unit when not in use.

Displaying text information

Selecting the desired text information

1 Press ! Depending on the version of iTunes used to

write MP3 files to a disc or media file types, incompatible text stored within an audio file may be displayed incorrectly.

! Text information items that can be changed

depend on the media.

Selecting and playing files/ tracks from the name list

1 Press to switch to the file/track name list mode.

2 Use M.C. to select the desired file name (or folder name).

Changing the file or folder name 1 Turn M.C.

Playing 1 When a file or track is selected, press M.C.

Viewing a list of the files (or folders) in the selected folder 1 When a folder is selected, press M.C.

Playing a song in the selected folder 1 When a folder is selected, press and hold M.C.

Advanced operations using special buttons

Selecting a repeat play range 1 Press 6/

Playing tracks in random order 1 Press 5/

! To change songs during random play, press d

Pausing playback 1 Press 4/PAUSE to pause or resume.

Enhancing compressed audio and restoring rich sound (sound retriever) 1 Press 3/S.Rtrv to cycle between:

to cycle between the following:

CD/CD-R/CD-RW

! ALL – Repeat all tracks ! ONE – Repeat the current track ! FLD – Repeat the current folder

USB audio player/USB memory

! ALL – Repeat all files ! ONE – Repeat the current file ! FLD – Repeat the current folder

to turn random play on or off. Tracks in a selected repeat range are played in random order.

to switch to the next track. Pressing c restarts playback of the current track from the beginning of the song.

1—2—OFF (off) 1 is effective for low compression rates, and 2

is effective for high compression rates.

Function settings

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select FUNCTION.

3 Turn M.C. to select the function.

After selecting, perform the following procedures to set the function.

Operating this unit

Section

REPEAT (repeat play)

1 Press M.C. to select a repeat play range.

For details, refer to Selecting a repeat play range on the previous page.

RANDOM (random play)

1 Press M.C. to turn random play on or off.

PAUSE (pause)

1 Press M.C. to pause or resume.

S.RTRV (sound retriever)

Automatically enhances compressed audio and restores rich sound. 1 Press M.C. to select the desired setting.

For details, refer to Enhancing compressed

audio and restoring rich sound (sound retriever)

on the previous page.

iPod

Basic operations

Playing songs on an iPod

1 Open the USB port cover. 2 Connect an iPod to the USB cable using an

iPod Dock Connector. A song will be played automatically.

Selecting a song (chapter) 1 Press c or d.

Selecting an album 1 Press 1/ ! The album may not be selected correctly if the

Fast forwarding or reversing 1 Press and hold c or d.

or 2/ .

iPod has more than one album with the same title on it. Select the album you want to listen to using list search. For details, refer to Brows- ing for a song on this page.

Notes

! The iPod cannot be turned on or off when the

control mode is set to CTRL AUDIO.

! Disconnect headphones from the iPod be-

fore connecting it to this unit.

! The iPod will turn off about two minutes after

the ignition switch is set to OFF.

Displaying text information

Selecting the desired text information

1 Press

Browsing for a song

1 Press to switch to the top menu of list search.

2 Use M.C. to select a category/song.

Changing the name of the song or category 1 Turn M.C.

Playlists—artists—albums—songs—podcasts —genres—composers—audiobooks

Playing 1 When a song is selected, press M.C.

Viewing a list of songs in the selected category 1 When a category is selected, press M.C.

Playing a song in the selected category 1 When a category is selected, press and hold

M.C.

Searching the list by alphabet 1 When a list for the selected category is dis-

played, press mode. ! You also can switch to alphabet search

mode by turning M.C. twice.

2 Turn M.C. to select a letter. 3 Press M.C. to display the alphabetical list.

! To cancel searching, press

to switch to alphabet search

Notes

! You can play playlists created with the PC ap-

plication (MusicSphere). The application will be available on our website.

! Playlists that you created with the PC appli-

cation (MusicSphere) are displayed in abbreviated form.

Advanced operations using special buttons

Selecting a repeat play range 1 Press 6/

! You cannot select OFF when CTRL AUDIO is

Playing all songs in random order (shuffle all) 1 Press 5/ ! When the control mode is set to CTRL iPod/

Pausing playback 1 Press 4/PAUSE to pause or resume.

Enhancing compressed audio and restoring rich sound (sound retriever) 1 Press 3/S.Rtrv to cycle between:

to cycle between the following:

! OFF – Repeat off ! ONE – Repeat the current song ! ALL – Repeat all songs in the selected list

selected. Refer to Operating this unit’siPod function from your iPod on this page.

to turn shuffle all on.

CTRL APP,shuffle play is on.

1—2—OFF (off) 1 is effective for low compression rates, and 2

is effective for high compression rates.

Playing songs related to the currently playing song

You can play songs from the following lists.

• Album list of the currently playing artist

• Song list of the currently playing album

• Album list of the currently playing genre

1 Press and hold M.C. to switch to link play mode.

2 Turn M.C. to change the mode; press to select.

! ARTIST – Plays an album of the artist cur-

rently being played.

! ALBUM – Plays a song from the album cur-

rently being played.

! GENRE – Plays an album from the genre cur-

rently being played.

The selected song/album will be played after the currently playing song.

Notes

! The selected song/album may be canceled if

you operate functions other than link search (e.g. fast forward and reverse).

! Depending on the song selected to play, the

end of the currently playing song and the beginning of the selected song/album may be cut off.

Operating this unit’s iPod function from your iPod

You can listen to the sound from your iPod applications using your car ’s speakers, when CTRL APP is selected. ! This function is not compatible with iPod

nano 1st generation. APP Mode is compatible with the following iPod models.

! iPhone 4 (software version 4.1 or later) ! iPhone 3GS (software version 3.0 or later) ! iPhone 3G (software version 3.0 or later) ! iPhone (software version 3.0 or later) ! iPod touch 4th generation (software version

4.1 or later)

! iPod touch 3rd generation (software version

3.0 or later)

! iPod touch 2nd generation (software version

3.0 or later)

English

Section

Operating this unit

! iPod touch 1st generation (software version

3.0 or later)

% Press BAND/ mode.

! CTRL iPod – This unit’s iPod function can be

operated from the connected iPod.

! CTRL APP – Play back the sound from your

iPod applications.

! CTRL AUDIO – This unit’s iPod function can

be operated from this unit.

to switch the control

Notes

! Switching the control mode to CTRL iPod/

CTRL APP pauses song playback. Operate

the iPod to resume playback.

! The following functions are still accessible

from the unit even if the control mode is set to CTRL iPod/CTRL APP.

— Pausing — Fast forward/reverse — Selecting a song (chapter)

! When the control mode is set to CTRL iPod,

operations are limited as follows:

— The function settings are not available. — The browse function cannot be operated from

this unit.

Function settings

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select FUNCTION.

3 Turn M.C. to select the function.

After selecting, perform the following procedures to set the function.

! When the control mode is set to CTRL iPod/

CTRL APP, only PAUSE or S.RTRV is avail-

able.

REPEAT (repeat play)

1 Press M.C. to select a repeat play range.

For details, refer to Selecting a repeat play range on the previous page.

SHUFFLE (shuffle)

1 Press M.C. to select your favorite setting.

! SNG – Play back songs in the selected list

in random order.

! ALB – Play back songs from a randomly se-

lected album in order.

! OFF – Cancel random play.

SHUFFLE ALL (shuffle all)

1 Press M.C. to turn shuffle all on.

To turn off, set SHUFFLE in the FUNCTION menu to off.

LINK PLAY (link play)

1 Press M.C. to display the setting mode. 2 Turn M.C. to change the mode; press to select.

For details about the settings, refer to Playing songs related to the currently playing song on

the previous page.

PAUSE (pause)

1 Press M.C. to pause or resume.

AUDIO BOOK (audiobook speed)

1 Press M.C. to display the setting mode. 2 Turn M.C. to select your favorite setting.

! FASTER – Playback at a speed faster than

normal

! NORMAL – Playback at normal speed ! SLOWER – Playback at a speed slower

than normal

3 Press M.C. to confirm the selection.

S.RTRV (sound retriever)

Automatically enhances compressed audio and restores rich sound. 1 Press M.C. to select the desired setting.

For details, refer to Enhancing compressed

audio and restoring rich sound (sound retriever)

on the previous page.

Audio adjustments

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select AUDIO.

3 Turn M.C. to select the audio function.

After selecting, perform the following procedures to set the audio function.

FAD/BAL (fader/balance adjustment)

1 Press M.C. to display the setting mode. 2 Press M.C. to cycle between fader (front/rear)

and balance (left/right). 3 Turn M.C. to adjust speaker balance. ! When the rear output and RCA output setting

are SW, you cannot adjust front/rear speaker

balance. Refer to REAR-SP (rear output setting)

on the next page. Refer to PREOUT (preout set-

ting) on the next page.

PRESET EQ (equalizer recall)

1 Press M.C. to display the setting mode. 2 Turn M.C. to select the equalizer.

DYNAMIC—VOCAL—NATURAL—CUSTOM

—FLAT—POWERFUL

3 Press M.C. to confirm the selection.

! You can also switch the equalizer by pressing

repeatedly (DEH-2400UB and DEH-24UB).

TONE CTRL (equalizer adjustment)

! Adjusted equalizer curve settings are stored in

CUSTOM.

1 Press M.C. to display the setting mode. 2 Press M.C. to select BASS (bass)/MID (mid)/

TREBLE (treble).

3 Turn M.C. to adjust the level.

Adjustment range: +6 to –6

LOUD (loudness)

Loudness compensates for deficiencies in the lowfrequency and high-frequency ranges at low volume.

1 Press M.C. to select the desired setting.

OFF (off)—LOW(low)—HI (high)

SUB.W (subwoofer on/off setting)

This unit is equipped with a subwoofer output which can be turned on or off. ! This function is not available for DEH-2400UB

and DEH-24UB.

1 Press M.C. to select the desired setting.

NOR (normal phase)—REV (reverse phase)— OFF (subwoofer off)

SUB.W CTRL (subwoofer adjustment)

Operating this unit

Section

The cut-off frequency and output level can be adjusted when the subwoofer output is on. Only frequencies lower than those in the selected range are outputted from the subwoofer. ! This function is not available for DEH-2400UB

and DEH-24UB.

! When you select OFF in SUB.W,you cannot se-

lect this function. For details, refer to SUB.W (subwoofer on/off setting) on the previous page.

1 Press M.C. to display the setting mode. 2 Press M.C. to cycle between the cut-off fre-

quency and output level of the subwoofer. Cut-off frequency (Cut-off frequency display flashes.)—Output level (Output level display flashes.)

3 Turn M.C. to select the desired setting.

Cut-off frequency: 50HZ—63HZ—80HZ—

100HZ—125HZ Output level: –24 to +6

SLA (source level adjustment)

SLA (Source level adjustment) lets you adjust the

volume level of each source to prevent radical changes in volume when switching between sources. ! Settings are based on the FM volume level,

which remains unchanged.

! The AM volume level can also be adjusted with

this function.

! When selecting FM as the source, you cannot

switch to SLA.

1 Press M.C. to display the setting mode. 2 Turn M.C. to adjust the source volume.

Adjustment range: +4 to –4

3 Press M.C. to confirm the selection.

Initial settings

1 Press and hold SRC/OFF until the unit turns off.

2 Press M.C. and hold until function name appears in the display.

3 Turn M.C. to select the initial setting.

After selecting, perform the following procedures to set the initial setting.

CLOCK SET (setting the clock)

1 Press M.C. to display the setting mode. 2 Press M.C. to select the segment of the clock

display you wish to set. Hour—Minute

3 Turn M.C. to adjust the clock.

AUX (auxiliary input)

Activate this setting when using an auxiliary device connected to this unit.

1 Press M.C. to turn AUX on or off.

USB PNP (plug and play)

This setting allows you to switch your source to USB/iPod automatically. 1 Press M.C. to turn the plug and play function

on or off. ON – When a USB storage device/iPod is con- nected, depending on the type of device, the source is automatically switched to USB/iPod when you turn on the engine. If you disconnect your USB storage device/iPod, this unit’s source is turned off. OFF – When a USB storage device/iPod is con- nected, the source is not switched to USB/ iPod automatically. Please change the source to USB/iPod manually.

REAR-SP (rear output setting)

The rear speaker leads output can be used for fullrange speaker or subwoofer connection. If you switch to SW, you can connect a rear speaker lead directly to a subwoofer without using an auxiliary amp. Initially, REAR-SP is set for rear full-range speaker connection (FUL).

1 Press M.C. to select the desired setting.

FUL—SW

! Even if you change this setting, there will

be no output if you select OFF in SUB.W (Refer to SUB.W (subwoofer on/off setting) on the previous page).

! If you change this setting, subwoofer out-

put in the audio menu will return to the factory settings.

PREOUT (preout setting)

The RCA outputs can be used for rear speaker or subwoofer connection. If you switch to SW, you can connect a rear speaker lead directly to a subwoofer without using an auxiliary amp. Initially, PREOUT is set for rear full-range speaker connection (SW).

1 Press M.C. to select the desired setting.

SW—REA

! Even if you change this setting, there will

be no output if you select OFF in SUB.W (Refer to SUB.W (subwoofer on/off setting) on the previous page).

! If you change this setting, subwoofer out-

put in the audio menu will return to the factory settings.

DEMO (demo display setting)

1 Press M.C. to turn the demo display on or off.

SCROLL (scroll mode setting)

When ever scroll is set to ON, recorded text information scrolls continuously in the display. Set to OFF if you prefer the information to scroll just once. 1 Press M.C. to turn the ever scroll on or off.

Selecting the illumination color

Only for DEH-3400UB and DEH-34UB. This unit is equipped with multiple-color illumination. You can select desired colors for the keys and display of this unit. You also can customize the colors you want to use.

Selecting the key color from the illumination color list

Only for DEH-3400UB and DEH-34UB. You can select desired colors for the keys of this unit.

1 Press

2 Turn M.C. to display KEY COLOR and press to select.

3 Turn M.C. to select the illumination color.

You can select one option from the following list.

4 Press M.C. to confirm the selection.

Notes

! When SCAN is selected, the system auto-

! When WARM is selected, the system auto-

! 30 preset colors (WHITE to ROSE) ! SCAN (cycle through all colors) ! 3 sets of colors (WARM, AMBIENT, CALM) ! CUSTOM (customized illumination color)

matically cycles through the 30 preset colors.

matically cycles through the warm colors.

English

Section

Operating this unit

! When AMBIENT is selected, the system au-

tomatically cycles through the ambient colors.

! When CALM is selected, the system auto-

matically cycles through the calm colors.

! When CUSTOM is selected, the customized

color saved is selected.

! To cancel selecting the illumination color,

press

Selecting the display color from the illumination color list

Only for DEH-3400UB and DEH-34UB. You can select the desired colors for the display of this unit.

1 Press

2 Turn M.C. to display DISP COLOR and press to select.

3 Turn M.C. to select the illumination color.

You can select one option from the following list.

4 Press M.C. to confirm the selection.

Note

For details about colors on the list, refer to Selecting the k ey color from the illumination color list on the previous page.

! 30 preset colors (WHITE to ROSE) ! SCAN (cycle through all colors) ! 3 sets of colors (WARM, AMBIENT, CALM) ! CUSTOM (customized illumination color)

Selecting key and display color from the illumination color list

Only for DEH-3400UB and DEH-34UB. You can select the desired colors for the keys and display of this unit.

1 Press

2 Turn M.C. to display BOTH COLOR and press to select.

3 Turn M.C. to select the illumination color.

You can select one option from the following list.

! 30 preset colors (WHITE to ROSE) ! SCAN (cycle through all colors)

4 Press M.C. to confirm the selection.

Notes

! You cannot select 3 sets of preset colors and

CUSTOM in this function.

! Once you select a color in this function, col-

ors on the keys and display of this unit automatically switch to the color you selected.

! For details about colors on the list, refer to

Selecting the key color from the illumination color list on the previous page.

Customizing the illumination color

Only for DEH-3400UB and DEH-34UB.

1 Press

2 Turn M.C. to display KEY COLOR or DISP COLOR. Press to select.

3 Press M.C. and hold until the customizing illumination color setting appears in the display.

4 Press M.C. to select the primary color. R (red)—G (green)—B (blue)

5 Turn M.C. to adjust the brightness level. Adjustment range: 0 to 60

# You cannot select a level below 10 for all three of R (red), G (green), and B (blue) at the same time.

# You can also perform the same operation on other colors.

Notes

! You cannot create a custom illumination

color when SCAN or a set of colors (WARM, AMBIENT,orCALM) is selected.

! You can create custom illumination colors

for both KEY COLOR and DISP COLOR.

Switching the dimmer setting

You can adjust the brightness of illumination.

% Press and hold

Using an AUX source

1 Insert the stereo mini plug into the AUX input jack.

2 Press SRC/OFF to select AUX as the source.

Note

AUX cannot be selected unless the auxiliary setting is turned on. For more details, refer to AUX (auxiliary input) on the previous page.

Turning the clock display on or off

% Press to turn the clock display on or off.

# The clock display disappears temporarily when you perform other operations, but the clock display appears again after 25 seconds.

4 56

4 5

Installation

Section

Connections

WARNING

! Use speakers over 50 W (output value) and

between 4 W to 8 W (impedance value). Do not use 1 W to 3 W speakers for this unit.

! The black cable is ground. When installing

this unit or power amp (sold separately), make sure to connect the ground wire first. Ensure that the ground wire is properly connected to metal parts of the car ’s body. The ground wire of the power amp and the one of this unit or any other device must be connected to the car separately with different screws. If the screw for the ground wire loosens or falls out, it could result in fire, generation of smoke or malfunction.

Ground wire

Other devices (Another electronic device in the car)

Important

! When installing this unit in a vehicle without

an ACC (accessory) position on the ignition switch, failure to connect the red cable to the terminal that detects operation of the ignition key may result in battery drain.

ACC position No ACC position

! Use this unit with a 12-volt battery and nega-

tive grounding only. Failure to do so may result in a fire or malfunction.

Metal parts of car’s bod

POWER AMP

! To prevent a short-circuit, overheating or mal-

function, be sure to follow the directions below.

— Disconnect the negative terminal of the bat-

tery before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. Wrap adhesive tape around wiring that comes into contact with metal parts to protect the wiring.

— Place all cables away from moving parts,

such as the shift lever and seat rails.

— Place all cables away from hot places, such

as near the heater outlet.

— Do not connect the yellow cable to the battery

by passing it through the hole to the engine compartment.

— Cover any disconnected cable connectors

with insulating tape.

— Do not shorten any cables. — Never cut the insulation of the power cable of

this unit in order to share the power with other devices. The current capacity of the cable is limited.

— Use a fuse of the rating prescribed. — Never wire the negative speaker cable directly

to ground.

— Never band together negative cables of multi-

ple speakers.

! When this unit is on, control signals are sent

through the blue/white cable. Connect this cable to the system remote control of an external power amp or the vehicle’s auto-antenna relay control terminal (max. 300 mA 12 V DC). If the vehicle is equipped with a glass antenna, connect it to the antenna booster power supply terminal.

! Never connect the blue/white cable to the

power terminal of an external power amp. Also, never connect it to the power terminal of the auto antenna. Doing so may result in battery drain or a malfunction.

This unit

DEH-3400UB and DEH-34UB

DEH-2400UB and DEH-24UB

1 Power cord input 2 Rear output or subwoofer output 3 Front output 4 Antenna input 5 Fuse (10 A) 6 Wired remote input

Hard-wired remote control adaptor can be connected (sold separately).

Power cord

Perform these connections when not connecting a rear speaker lead to a subwoofer.











e f





c d



Perform these connections when using a subwoofer without the optional amplifier.









1 To power cord input 2 Left 3 Right 4 Front speaker 5 Rear speaker 6 White 7 White/black 8 Gray 9 Gray/black a Green b Green/black c Violet d Violet/black e Black (chassis ground)

Connect to a clean, paint-free metal location.

f Yellow

Connect to the constant 12 V supply terminal.

g Red

Connect to terminal controlled by ignition switch (12 V DC).

h Blue/white

Connect to system control terminal of the power amp or auto-antenna relay control terminal (max. 300 mA 12 V DC).

i Subwoofer (4 Ω)

c d

f g

k l













English

Section

Installation

j When using a subwoofer of 70 W (2 Ω), be

sure to connect the subwoofer to the violet and violet/black leads of this unit. Do not connect anything to the green and green/ black leads.

k Not used. l Subwoofer (4 Ω)× 2

Notes

! With a 2 speaker system, do not connect any-

thing to the speaker leads that are not connected to speakers.

! Change the initial setting of this unit. Refer

to REAR-SP (rear output setting) on page 9. Refer to PREOUT (preout setting) on page 9. The subwoofer output of this unit is monaural.

Power amp (sold separately)

Perform these connections when using the optional amplifier. DEH-3400UB and DEH-34UB





DEH-2400UB and DEH-24UB



1 System remote control

Connect to Blue/white cable.

2 Power amp (sold separately) 3 Connect with RCA cables (sold separately)

4 To Front output 5 Front speaker 6 To Rear output or subwoofer output 7 Rear speaker or subwoofer

Installation

Important

! Check all connections and systems before

final installation.

! Do not use unauthorized parts as this may

cause malfunctions.

! Consult your dealer if installation requires

drilling of holes or other modifications to the vehicle.

! Do not install this unit where:

— it may interfere with operation of the vehicle. — it may cause injury to a passenger as a result

of a sudden stop.

! The semiconductor laser will be damaged if

it overheats. Install this unit away from hot places such as near the heater outlet.

! Optimum performance is obtained when the

unit is installed at an angle of less than 60°.

DIN front/rear mount

This unit can be properly installed using either front-mount or rear-mount installation. Use commercially available parts when installing.

60°

DIN Front-mount

1 Insert the mounting sleeve into the dashboard.

For installation in shallow spaces, use the supplied mounting sleeve. If there is enough space, use the mounting sleeve that came with the vehicle.

2 Secure the mounting sleeve by using a screwdriver to bend the metal tabs (90°) into place.

1 Dashboard 2 Mounting sleeve

3 Install the unit as illustrated.

1 Nut 2 Firewall or metal support 3 Metal strap 4 Screw 5 Screw (M4 × 8)

# Make sure that the unit is installed securely in place. An unstable installation may cause skipping or other malfunctions.

DIN Rear-mount

1 Determine the appropriate position where the holes on the bracket and the side of the unit match.

2 Tighten two screws on each side.

1 Screw 2 Mounting bracket 3 Dashboard or console

! Use either truss (5 mm × 8 mm) or flush sur-

face (5 mm × 9 mm) screws, depending on the bracket screw holes.

Removing the unit

1 Remove the trim ring.

1 Trim ring 2 Notched tab

! Releasing the front panel allows easier ac-

cess to the trim ring.

! When reattaching the trim ring, point the

side with the notched tab down.

Installation

Additional information

Section

2 Insert the supplied extraction keys into both sides of the unit until they click into place.

3 Pull the unit out of the dashboard.

Removing and re-attaching the front panel

You can remove the front panel to protect your unit from theft. Press the detach button and push the front panel upward and pull it toward you. For details, refer to Removing the front panel to

protect your unit from theft and Re-attaching the front panel on page 4.

Securing the front panel

The front panel can be secured with the supplied screw.

1 Screw

Troubleshooting

Symptom Cause Action

The display illumination turns on and off at random.

The display automatically returns to the ordinary display.

The repeat play range changes unexpectedly.

A subfolder is not played back.

NO XXXX appears when a display is changed (NO TITLE, for example).

Demo mode is on.

You did not perform any operation within about 30 seconds.

Depending on the repeat play range, the selected range may change when another folder or track is being selected or during fast forwarding/reversing.

Subfolders cannot be played when FLD (folder repeat) is selected.

There is no embedded text information.

Turn off the demo display setting.

Perform operation again.

Select the repeat play range again.

Select another repeat play range.

Switch the display or play another track/file.

Symptom Cause Action

The unit is malfunctioning. There is interference.

You are using a device, such as a cellular phone, that transmits electric waves near the unit.

Move electrical devices that may be causing the interference away from the unit.

Error messages

When you contact your dealer or your nearest Pioneer Service Center, be sure to note the error message.

Built-in CD Player

Message Cause Action

ERROR-07, 11, 12, 17, 30

ERROR-07, 10, 11, 12, 15, 17, 30, A0

ERROR-15 Theinserted

ERROR-23 Unsupported

FRMT READ Sometimes

The disc is dirty. Clean the disc. The disc is

scratched. There is an elec-

trical or mechanical error.

disc is blank.

CD format.

there is a delay between the start of playback and when you start to hear any sound.

Replace the disc.

Turn the ignition switch OFF and back ON, or switch to a different source, then back to the CD player.

Replace the disc.

Wait until the message disappears and you hear sound.

English

Appendix

Additional information

Message Cause Action

NO AUDIO The inserted

SKIPPED The inserted

PROTECT All the files on

USB storage device/iPod

Message Cause Action

NO DEVICE When plug and

FRMT READ Sometimes

NO AUDIO There are no

disc does not contain any playable files.

disc contains DRM protected files.

the inserted disc are embedded with DRM.

play is off, no USB storage device or iPod is connected.

there is a delay between the start of playback and when you start to hear any sound.

songs.

The connected USB storage device has security enabled.

Replace the disc.

! Turn the plug and play on. ! Connect a compatible USB storage device/iPod.

Wait until the message disappears and you hear sound.

Transfer the audio files to the USB storage device and connect.

Follow the USB storage device instructions to disable the security.

Message Cause Action

SKIPPED The connected

PROTECT All the files in

N/A USB The USB device

USB storage device contains files embedded with Windows Mediaä DRM 9/

10.

the USB storage device are embedded with Windows Media DRM 9/10.

connected to is not supported by this unit.

Play an audio file not embedded with Windows Media DRM 9/10.

Transfer audio files not embedded with Windows Media DRM 9/10 to the USB storage device and connect.

! Connect a USB Mass Storage Class compliant device. ! Disconnect your device and replace it with a compatible USB storage device.

Message Cause Action

CHECK USB The USB con-

nector or USB cable has shortcircuited.

The connected USB storage device consumes more than 500 mA (maximum allowable current).

The iPod operates correctly but does not charge.

Check that the USB connector or USB cable is not caught in something or damaged.

Disconnect the USB storage device and do not use it. Turn the ignition switch to OFF, then to ACC or ON and then connect only compliant USB storage devices.

Make sure the connection cable for the iPod has not shorted out (e.g., not caught in metal objects). After checking, turn the ignition switch OFF and back ON, or disconnect the iPod and reconnect.

Message Cause Action

ERROR-19 Communication

ERROR-23 USB storage de-

ERROR-16 TheiPod firm-

STOP There are no

failed.

iPod failure. Disconnect the

vice was not formatted with FAT12, FAT16 or FAT32.

ware version is old.

iPod failure. Disconnect the

songs in the current list.

Perform one of the following operations. –Turn the ignition switch OFF and back ON. –Disconnect the USB storage device. –Change to a different source. Then, return to the USB source.

cable from the iPod. Once the iPod’s main menu is displayed, reconnect the iPod and reset it.

USB storage device should be formatted with FAT12, FAT16 or FAT32.

Update the iPod version.

cable from the iPod. Once the iPod’s main menu is displayed, reconnect the iPod and reset it.

Select a list that contains songs.

Additional information

Appendix

Additional information

Message Cause Action

NOT FOUND No related

songs.

Transfer songs to the iPod.

Handling guidelines

Discs and player

Use only discs that feature either of the following two logos.

Use 12-cm discs. Do not use 8-cm discs or an adapter for 8-cm discs.

Use only conventional, fully circular discs. Do not use shaped discs.

Do not insert anything other than a CD into the CD loading slot.

Do not use cracked, chipped, warped, or otherwise damaged discs as they may damage the player.

Unfinalized CD-R/RW discs cannot be played back.

Do not touch the recorded surface of the discs.

Store discs in their cases when not in use.

Do not attach labels, write on or apply chemicals to the surface of the discs.

To clean a CD, wipe the disc with a soft cloth outward from the center.

Condensation may temporarily impair the player ’s performance. Let it rest for about one hour to adjust to a warmer temperature. Also, wipe any damp discs off with a soft cloth.

Playback of discs may not be possible because of disc characteristics, disc format, recorded application, playback environment, storage conditions, and so on.

Road shocks may interrupt disc playback.

When using discs that can be printed on label surfaces, check the instructions and the warnings of the discs. Depending on the discs, inserting and ejecting may not be possible. Using such discs may result in damage to this equipment.

Do not attach commercially available labels or other materials to the discs. ! The discs may warp making the disc unplay-

able.

! The labels may come off during playback and

prevent ejection of the discs, which may result in damage to the equipment.

USB storage device

Connections via USB hub are not supported.

Do not connect anything other than a USB storage device.

Firmly secure the USB storage device when driving. Do not let the USB storage device fall onto the floor, where it may become jammed under the brake or accelerator pedal.

Depending on the USB storage device, the following problems may occur.

! Operations may vary. ! The storage device may not be recognized. ! Files may not be played back properly. ! The device may generate noise in the radio.

iPod

Do not leave the iPod in places with high temperatures.

To ensure proper operation, connect the dock connector cable from the iPod directly to this unit.

Firmly secure the iPod when driving. Do not let the iPod fall onto the floor, where it may become jammed under the brake or accelerator pedal.

About iPod settings ! When an iPod is connected, this unit changes

the EQ (equalizer) setting of the iPod to off in order to optimize the acoustics. When you disconnect the iPod, the EQ returns to the original setting.

! You cannot set Repeat to off on the iPod when

using this unit. Repeat is automatically changed to All when the iPod is connected to this unit.

Incompatible text saved on the iPod will not be displayed by the unit.

DualDiscs

DualDiscs are two-sided discs that have a recordable CD for audio on one side and a recordable DVD for video on the other. Since the CD side of DualDiscs is not physically compatible with the general CD standard, it may not be possible to play the CD side with this unit. Frequent loading and ejecting of a DualDisc may result in scratches on the disc. Serious scratches can lead to playback problems on this unit. In some cases, a DualDisc may become stuck in the disc loading slot and will not eject. To prevent this, we recommend you refrain from using DualDisc with this unit. Please refer to the information from the disc manufacturer for more detailed information about DualDiscs.

Compressed audio compatibility (disc, USB)

WMA

File extension: .wma

Bit rate: 48 kbps to 320 kbps (CBR), 48 kbps to 384 kbps (VBR)

Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz

Windows Media Audio Professional, Lossless, Voice/DRM Stream/Stream with video: Not compatible

MP3

File extension: .mp3

Bit rate: 8 kbps to 320 kbps (CBR), VBR

Sampling frequency: 8 kHz to 48 kHz (32 kHz,

44.1 kHz, 48 kHz for emphasis)

English

Appendix

Additional information

Compatible ID3 tag version: 1.0, 1.1, 2.2, 2.3, 2.4 (ID3 tag Version 2.x is given priority over Version 1. x.)

M3u playlist: Not compatible

MP3i (MP3 interactive), mp3 PRO: Not compatible

WAV

File extension: .wav

Quantization bits: 8 and 16 (LPCM), 4 (MS ADPCM)

Sampling frequency: 16 kHz to 48 kHz (LPCM),

22.05 kHz and 44.1 kHz (MS ADPCM)

Supplemental information

Only the first 32 characters can be displayed as a file name (including the file extension) or a folder name.

This unit may not operate correctly depending on the application used to encode WMA files.

There may be a slight delay at the start of playback of audio files embedded with image data or audio files stored on a USB storage device that has numerous folder hierarchies.

Disc

Playable folder hierarchy: up to eight tiers (A practical hierarchy is less than two tiers).

Playable folders: up to 99

Playable files: up to 999

File system: ISO 9660 Level 1 and 2, Romeo, Joliet

Multi-session playback: Compatible

Packet write data transfer: Not compatible

Regardless of the length of blank sections between the songs from the original recording, compressed audio discs play with a short pause between songs.

USB storage device

Playable folder hierarchy: up to eight tiers (A practical hierarchy is less than two tiers).

Playable folders: up to 500

Playable files: up to 15 000

Playback of copyright-protected files: Not compatible

Partitioned USB storage device: Only the first partition can be played.

There may be a slight delay when starting playback of audio files on a USB storage device with numerous folder hierarchies.

CAUTION

Do not leave discs or a USB storage device in any place that is subject to high temperatures.

iPod compatibility

This unit supports only the following iPod models. Supported iPod software versions are shown below. Older versions may not be supported. Made for

! iPhone 4 (software version 4.1) ! iPhone 3GS (software version 3.0.1) ! iPhone 3G (software version 2.0) ! iPhone (software version 1.1.1) ! iPod nano 6th generation (software version

1.0)

! iPod nano 5th generation (software version

1.0.1)

! iPod nano 4th generation (software version

1.0)

! iPod nano 3rd generation (software version

1.0)

! iPod nano 2nd generation (software version

1.1.2)

! iPod nano 1st generation (software version

1.2.0)

! iPod touch 4th generation (software version

4.1)

! iPod touch 3rd generation (software version

3.1.1)

! iPod touch 2nd generation (software version

2.1.1)

! iPod touch 1st generation (software version

1.1)

! iPod classic 160GB (software version 2.0.2) ! iPod classic 120GB (software version 2.0) ! iPod classic (software version 1.0)

Depending on the generation or version of the iPod, some functions may not be available.

Operations may vary depending on the software version of iPod.

When using an iPod, an iPod Dock Connector to USB Cable is required.

A Pioneer CD-IU50 interface cable is also available. For details, consult your dealer.

About the file/format compatibility, refer to the iPod manuals.

Audiobook, Podcast: Compatible

CAUTION

Pioneer accepts no responsibility for data lost on the iPod, even if that data is lost while this unit is used.

Sequence of audio files

The user cannot assign folder numbers and specify playback sequences with this unit.

Example of a hierarchy

 

 

Level 1 Level 2 Level 3 Level 4

Disc

Folder selection sequence or other operation may differ depending on the encoding or writing software.

USB storage device

Playback sequence is the same as recorded sequence in the USB storage device. To specify the playback sequence, the following method is recommended. 1 Create a file name that includes numbers

that specify the playback sequence (e.g., 001xxx.mp3 and 099yyy.mp3).

2 Put those files into a folder.



audio file



01 to 05: Folder number 1 to 6: Playback sequence

: Folder

: Compressed

Additional information

Appendix

Additional information

3 Save the folder containing files on the USB

storage device. However,depending on the system environment, you may not be able to specify the playback sequence. For USB portable audio players, the sequence is different and depends on the player.

iTunes

Apple and iTunes are trademarks of Apple Inc., registered in the U.S. and other countries.

MP3

Supply of this product only conveys a license for private, non-commercial use and does not convey a license nor imply any right to use this product in any commercial (i.e. revenue-generating) real time broadcasting (terrestrial, satellite, cable and/or any other media), broadcasting/ streaming via internet, intranets and/or other networks or in other electronic content distribution systems, such as pay-audio or audio-on-demand applications. An independent license for such use is required. For details, please visit http://www.mp3licensing.com.

WMA

Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product includes technology owned by Microsoft Corporation and cannot be used or distributed without a license from Microsoft Licensing, Inc.

iPod & iPhone

iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.

“Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulator y standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance.

Specifications

General

Power source ................... 14.4 V DC (10.8 V to 15.1 V al-

Grounding system ............ Negative type

Maximum current consumption

................................... 10.0 A

Dimensions (W × H × D):

DIN

Chassis .............. 178 mm × 50 mm ×

Nose .................. 188mm × 58mm ×

Chassis .............. 178 mm × 50 mm ×

Nose .................. 170mm × 46mm ×

Weight ............................. 1.1 kg (2.4 lbs)

Audio

Maximum power output ... 50 W × 4

Continuous power output

................................... 22 W × 4 (50 Hz to 15000 Hz,

Load impedance .............. 4 W (4 W to 8 W allowable)

Preout maximum output level

................................... 2.0 V

Tone controls:

Bass

Frequency .......... 100Hz

Gain .................. ±12dB

Mid

Frequency .......... 1 kHz

Gain .................. ±12dB

Treble

Frequency .......... 10 kHz

Gain .................. ±12dB

Subwoofer (mono):

Frequency ................. 50 Hz/63 Hz/80 Hz/100 Hz/

Slope ........................ –18 dB/oct

Gain ......................... +6dB to –24 dB

Phase ....................... Normal/Reverse

CD player

System ............................ Compact disc audio sys tem

lowable)

165 mm (7 in. × 2 in. × 6-1/2 in.)

16 mm (7-3/8 in.× 2-1/4 in.× 5/8 in.)

165 mm (7 in.× 2 in.× 6-1/2 in.)

16 mm (6-3/4 in.× 1-3/4 in.× 5/8 in.)

70 W × 1/2 W (for subwoofer)

5 % THD, 4 W load, both channels driven)

125 Hz

Usable discs .................... Compact disc

Signal-to-noise ratio ......... 94 dB (1 kHz) (IHF-A network)

Number of channels ........ 2 (stereo)

MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3

WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2ch

WAV signal format ........... Linear PCM & MS ADPCM

USB

USB standard specification

................................... USB 2.0 full speed

Maximum current supply

................................... 1 A

USB Class ....................... MSC (Mass Storage Class)

File system ....................... FAT12, FAT16, FAT32

MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3

WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2ch

WAV signal format ........... Linear PCM & MS ADPCM

FM tuner

Frequency range .............. 87.9 MHz to 107.9 MHz

Usable sensitivity ............. 9 dBf (0.8 µV/75 W, mono, S/N:

Signal-to-noise ratio ......... 72 dB (IHF-A network)

AM tuner

Frequency range .............. 530 kHz to 1 710 kHz

Usable sensitivity ............. 25 µV (S/N: 20 dB)

Signal-to-noise ratio ......... 62 dB (IHF-A network)

audio) (Windows Media Player)

(Non-compressed)

audio) (Windows Media Player)

(Non-compressed)

30 dB)

CEA2006 Specifications

Power output ................... 14 W RMS × 4 Channels (4 W

S/N ratio .......................... 91 dBA (reference: 1 W into

Note

Specifications and the design are subject to modifications without notice.

and ≦ 1 % THD+N)

4 W)

English

+ 39 hidden pages