Philips V315B1-L05, V320B1-L05, V470H1-L03 Serivce Manual

Colour Television Module

CMO (CHI MEI OPT.) LCD 2k7

V315B1-L05
V320B1-L05
V470H1-L03

Contents Page

1. Technical Specifications, Connections, and Chassis
Overview 2

2. Safety Instructions, Warnings, and Notes 3

3. Directions for Use 4

4. Mechanical Instructions 5

5. Service Modes, Error Codes, and Fault Finding 10

6. Block Diagrams, Test Point Overviews, and
Waveforms 11

7. Circuit Diagrams and PWB Layouts 11

8. Alignments 11

9. Circuit Descriptions, Abbreviation List, and IC Data
Sheets 11

10. Spare Parts List 11

11. Revision List 11

©

Copyright 2007 Philips Consumer Electronics B.V. Eindhoven, The Netherlands.
All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system or transmitted, in any form or by any means, electronic,
mechanical, photocopying, or otherwise without the prior permission of Philips.

Published by MW 0770 BU CD Customer Service Printed in the Netherlands Subject to modification EN 3122 785 16921

EN 2 LCD CMO 2K71.

Technical Specifications, Connections, and Chassis Overview

1. Technical Specifications, Connections, and Chassis Overview

Index of this chapter:

1.1 Introduction

1.2 General

1.3 Specifications

Note:

• Specifications are indicative (subject to change).

1.1 Introduction

In this Service Manual you will find all necessary information to
perform the Board Level Repair (= board swap) scenario on
LCD panels. The LCD repair manuals are created per brand,
and they will contain all necessary information for the different
panels used in Philips flat LCD TVs.

1.2 General

CHI MEI

OPTOELECTRONICS

(a) Model Name: V320B1-L05
(b) Revision: Rev. XX, for example: A0, A1… B1, B2… or C1, C2…etc.
(c) Serial ID: X X X X X X X Y M D L N N N N

Serial ID includes the information as below:

(a) Manufactured Date: Year: 0~9, for 2000~2009

Day: 1~9, A~Y, for 1

(b) Revision Code: Cover all the change
(c) Serial No.: Manufacturing sequence of product
(d) Product Line: 1 -> Line1, 2 -> Line 2, …etc.

V320B1 -L05 Rev. XX

X X X X X X X Y M D L N N N N

Month: 1~9, A~C, for Jan. ~ Dec.

st

to 31st, exclude I ,O, and U.

E207943

MADE IN TAIWAN

Serial No.
Product Line

Year, Month, Date
CMO Internal Use

CMO Internal Use

Revision

CMO Internal Use

H_16920_023.eps

200407

Figure 1-1 CMO module label

1.3 Specifications

Below find attached the data sheets of the different LCD
panels. Click on the “model number” to open.

• Model V315B1-L05

• Model V320B1-L05

• Model V470H1-L03

Safety Instructions, Warnings, and Notes

2. Safety Instructions, Warnings, and Notes

EN 3LCD CMO 2K7 2.

Index of this chapter:

2.1 General

2.2 Safety Precautions

2.3 Servicing Precautions

2.1 General

Notes:

• Only authorised persons should perform servicing of this
module.

• When using/handling this unit, pay special attention to the
LCD Module: it should not be enforced into any other way
then next rules, warnings, and/or cautions.

• "Warning" indicates a hazard that may lead to death or
injury if the warning is ignored and the product is handled
incorrectly.

• "Caution" indicates a hazard that can lead to injury or
damage to property if the caution is ignored and the
product is handled incorrectly.

2.2 Safety Precautions

2.2.1 Warning

• Do not supply a voltage higher than specified to this
product. This may damage the product or can create
hazardous situations.

• Do not use this product in locations where the humidity is
extremely high, where it may be splashed with water, or
where flammable materials surround it.

• Do not install or use the product in a location that does no
satisfy specified environmental conditions. This may
damage the product or can create hazardous situations.

• If a foreign substance (such as water, metal, or liquid) gets
inside the product, immediately turn “OFF” the power.
Continuing to use the product may cause electric shock or
can create hazardous situations.

• If the product emits smoke and abnormal smell, or makes
an abnormal sound, immediately turn “OFF” the power.
Continuing to use the product may cause electric shock or
can create hazardous situations.

• Do not (dis)connect the connector while power to the
product is “ON”. It takes some time for the voltage to drop
to a sufficiently low level after the power has been turned
“OFF”. Confirm that the voltage has dropped to a safe level
before (dis)connecting the connector.

• Do not pull out or insert the power cable from/to an outlet
with wet hands. It may cause electric shock.

• If the power cable is damaged, or if the connector is loose,
do not use the product, otherwise, this can lead to
hazardous situations or may cause electric shock.

• The LCD Backlight Inverter unit uses a high voltage for the
lamps. Keep the cautions concerning electric shock and do
not touch the device circuitry handling the inverter unit. And
because the capacitors of the device circuitry may remain
charged at the moment of Power “OFF”, standing for 1
minute is required in order to discharge the device circuitry.

2.2.2 Caution

• Do not place this product in a location that is subject to
heavy vibration, or an unstable surface such as an inclined
surface. The product may fall off or fall over, causing
injuries.

• Before disconnecting cable from the product, be sure to
turn off the power. Be sure to hold the connector when
disconnecting cables. Pulling a cable with excessive force
may cause the core of the cable to be exposed or break the
cable, and this can lead to fire or electric shock.

• This product contains glass. If shock, vibration, heat or
distortion is applied to the product, the glass may be
broken.

• If glass surface of the display breaks or is scratched, do not
touched the broken pieces or the scratched with bare
hands. You may be injured.

• LCD Module requires to be handled with special care. LCD
Module is not to be touched with metal or hard materials.
Must not be stressed by heat or mechanical impact.

• There are some particular components on the rear panel of
this product. Skin contact with these components may
cause an electric shock. So, handle with care.

• While moving the product, be sure to turn off the power,
disconnect all cables and watch your step. Dropping the
product may cause injuries from electric shock. So, while
moving the product handle with care.

• When cleaning the panel is necessary, wipe it with a soft
and moistened cloth a neural detergent. Caution on
connector area. Do not use chemicals such as thinner or
benzene.

• LCD Module emits heat from the Lamp, Backlight lamp,
and component parts. Therefore, the environmental
temperature must not exceed 50 deg. C. LCD Module
Backlight Inverter system is driven by high voltage, so it
must avoid conductive materials.

• If repairing components with a lead line, high voltage or
high temperature components must be put out from a lead
line and fix.

• Do not place an object on the surface of the display. The
glass may break or be scratched.

• This product may be damaged if it is subject to excessive
stresses (such as excessive voltage, current, or
temperature). The absolute maximum ratings specify the
limits of these stresses.

• Do not cover or wrap with any covering materials while
power is applied to the product.

• This product is made from various materials such as glass,
metal, and plastic. When discarding it, be sure to contact a
purchase place.

• If a discrepancy occurs due to any arbitrary modification or
disassembly, supplier is not responsible for function,
quality or other items.

• Within the warranty period, general faults may be charged
for depending on responsibility for the faults. You handle
with care

2.3 Servicing Precautions

A colour TFT LCD Module can easily be damaged by both
electrical and mechanical stresses. Users therefore, are
requested to follow the “Servicing precautions of colour TFT
LCD Module” on the following.

2.3.1 System Assembler

• Follow the power sequence: An abnormal power
sequence may cause critical malfunction or electrical
damage.

• Prevent physical stress.

• Prevent overheat:
– High temperatures on the surface of the screen may

cause poor quality. Please use the LCD Module on the
specified temperatures.

– Low temperatures (under 10 deg. C) makes the LCD

Module respond slowly, make the Backlight worse
operated, and will shorten very much the lifetime
accordingly.

• Keep LCD Module dust-free: The LCD Module is
sensitive against dust; it can cause visual or functional
problems.

EN 4 LCD CMO 2K73.

Directions for Use

• Do not touch TCP area: Do not touch TCP area at any

case. It can cause Driver IC cracks, film cracks, etc. The
TCP is the weakest point of the LCD Module.

• Do not pull Backlight wire: Please do not pull the

Backlight wire, as it can cause the wire to become
disconnected or damaged.

• Check the connections of the Inverter & Backlight
connectors: Incomplete connection can cause burnt in
Backlight connectors or damage the inverter.

• Handle with care:
– Please do not drop, bend, or hit the LCD Module.
– Physical stress can cause defects as broken panels.

• Keep mounting screw length and motor driver’s
torque: Strong motor driver’s torque can make a
mechanical defect on LCD Module. Please keep within the
specifications.

• Do not operate for a long time under the same pattern:
Operating the LCD Module for a long time with the same
video pattern can cause image persistence and can
eventually damage it.

• Defective panels must also be handled with care:
– To prevent making other defects, please handle the

defective LCD Module as a good one.

– Defective LCD Modules must be repaired.

• Do not stack LCD Modules: The LCD Module consists of
fragile components such as TCPs or Glasses. Stacking the
LCD Modules can cause undesired defects.

• Do not provide strong pressure at connecting: Strong
pressure can transfer the force to the TCP, which is the
weakest part of the LCD Module. It eventually can make
the TCP crack or lead to other unexpected defects.

• Let the Backlight Wire at the backside of the LCD
Module: If let the Backlight wire in front of the LCD Module,
the Backlight connector can hurt the surface of the
polariser.

• Never (dis)connect at power “ON”: The LCD Module

consists of CMOS components, which are known as weak
components against EOS. It can damage the product.

• Electro-static discharge can make damage:

– Semi-assembled product should be handled with wrist

strap.
– Earth human body when handle the LCD Module.
– Please do not touch the interface connector pin.

2.3.2 System Assembler/End User

• Keep clean the surface:

– Please wear rubber gloves when you touch the surface

of the LCD Module screen.
– Please use soft and anti-static material with n-Hexane

as cleaner.

• Be careful not to make polariser scratch:

– Surface of polariser is soft, so it’s easily scratched.
– Please do not touch, press or rub on polariser surface

with materials over HB hardness.

• Be careful with swift temperature and humidity
changes: Swift temperature and or humidity change can
make dew condensation or ice, which can cause non­conformance such as malfunctioning.

• Keep out of water:
– Water on in the LCD Module can cause electrical short

or corrosion.

– Please wipe out or dry water carefully.

• Keep the LCD Module free from corrosive gasses:
Corrosive gas can chemically damage the polariser and
the circuitry parts and eventually will cause defects.

• Keep the suitable temperature and humidity: High
temperatures and high humidity will shorten the lifetime

3. Directions for Use

Not applicable.