Philips UDA1331H Datasheet

INTEGRATED CIRCUITS

DATA SH EET

UDA1331H

Universal Serial Bus (USB) Audio Playback Peripheral (APP)

Preliminary speciﬁcation Supersedes data of 1998 Apr 16 File under Integrated Circuits, IC01

1998 Oct 06

Philips Semiconductors Preliminary speciﬁcation

Universal Serial Bus (USB) Audio Playback Peripheral (APP)

FEATURES General

• Universal Serial Bus (USB) stereo Audio Playback Peripheral (APP) system with adaptive (5 to 55 kHz) 20-bits digital-to-analog conversion and filtering

• USB-compliant audio and Human Interface Device (HID)

• Supports 12 Mbits/s full-speed serial data transmission

• Supports multiple audio data formats (8, 16 and 24 bits)

• Supports headphone and line output

• Fully automatic ‘Plug-and-Play’ operation

• High linearity

• Wide dynamic range

• Superior signal-to-noise ratio (typical 95 dB)

• Low total harmonic distortion (typical 90 dB)

• 3.3 V power supply

• Efficient power management

• Low power consumption

• On-chip master clock oscillator, only an external crystal

is required

• Partly programmable USB descriptors and configuration

C-bus.

via I

Sound processing

• Separate digital volume control for left and right channel

• Soft mute

• Digital bass and treble tone control

• External Digital Sound Processor (DSP) option possible

via standard I

• Selectable clipping prevention

• Selectable Dynamic Bass Boost (DBB)

• On-chip digital de-emphasis.

S-bus or Japanese digital I/O format

UDA1331H

Document references

•

“USB Specification”

•

“USB Common Class Specification”

•

“USB Device Class Definition for Audio Devices”

•

“Device Class Definition for Human Interface Devices (HID)”

•

“USB HID Usage Table”

APPLICATIONS

• USB monitors

• USB speakers

• USB headsets

• USB telephone/answering machines

• USB links in consumer audio devices.

GENERAL DESCRIPTION

The UDA1331H is a stereo CMOS digital-to-analog bitstream converter designed for USB-compliant audio playback devices and multimedia audio applications. The UDA1331H is an adaptive asynchronous sink USB audio device with a continuous sampling frequency (f range from 5 to 55 kHz. It contains a USB interface, an embedded microcontroller and an Asynchronous Digital-to-Analog Converter (ADAC).

The USB interface is the interface between the USB, the ADAC and the microcontroller. The USB interface consists of an analog front-end and a USB processor. The analog front-end transforms the differential USB data to a digital data stream. The USB processor buffers the input and output data from the analog front-end and handles all low-level USB protocols. The USB processor selects the relevant data from the universal serial bus, performs an extensive error detection and separates control information (input and output) and audio information (input only).

)

1998 Oct 06 2

Philips Semiconductors Preliminary speciﬁcation

Universal Serial Bus (USB) Audio

UDA1331H

Playback Peripheral (APP)

The control information becomes accessible at the microcontroller. The audio information becomes available at the digital I/O output or is fed directly to the ADAC.

The microcontroller handles the high-level USB protocols, translates the incoming control requests and manages the user interface via General Purpose (GP) pins and an I2C-bus. The firmware for the microcontroller must be located in an external (E)PROM.

The ADAC enables the wide and continuous range of input sampling frequencies. By means of a Sample Frequency Generator (SFG), the ADAC is able to reconstruct the average sample frequency from the incoming audio samples. The ADAC also performs the sound processing. The ADAC consists of FIFO registers, a unique audio

QUICK REFERENCE DATA

SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT

Supplies

DD(tot)

DD(ps)

supply voltage note 1 3.0 3.3 3.6 V total supply current − 50 − mA supply current in power-save

mode

Dynamic performance DAC

THD N+

---------------------- S

total harmonic distortion-plus-noise to signal

fs= 44.1 kHz; RL=5kΩ

at input signal of 1 kHz (0 dB) −−90

ratio

at input signal of 1 kHz (−60 dB) −−30

S/N

signal-to-noise ratio at bipolar

A-weighted at code 0000H 90 95 − dBA

zero

o(FS)(rms)

full-scale output voltage

VDD= 3.3 V − 0.66 − V

(RMS value)

General characteristics

i(sample)

amb

audio sample input frequency 5 − 55 kHz operating ambient temperature 0 25 70 °C

feature processing DSP, the SFG, digital up-sampling filters, a variable hold register, a Noise Shaper (NS) and a Filter Stream DAC (FSDAC) with integrated filter and line output drivers. The audio information is applied to the ADAC via the USB processor or via the digital I/O input.

An external DSP can be used for adding extra sound processing features via the digital I/O-bus.

The UDA1331H supports the standard I2S-bus data input format and the LSB-justified serial data input format with word lengths of 16, 18 and 20 bits.

The wide dynamic range of the bitstream conversion technique used in the UDA1331H guarantees a high audio sound quality.

− 18 − mA

(2)

−80 dB

− 0.0032 0.01 %

(2)

−20 dB

− 3.2 10 %

Notes

1. V

is the supply voltage on pins V

DDA

, V

DDE

, V

DDI

and V

. VSS is the ground on pins V

DDX

SSA

, V

SSE

, V

SSI

and V

All VDD and VSS pins must be connected to the same supply or ground respectively.

2. The audio information from the USB interface is fed directly to the ADAC.

ORDERING INFORMATION

TYPE

NUMBER

NAME DESCRIPTION VERSION

PACKAGE

UDA1331H QFP64 plastic quad ﬂat package; 64 leads (lead length 1.95 mm); body 14 × 20 × 2.8 mm SOT319-2

1998 Oct 06 3

SSX

Philips Semiconductors Preliminary speciﬁcation

Universal Serial Bus (USB) Audio Playback Peripheral (APP)

BLOCK DIAGRAM

handbook, full pagewidth

RTCB

SHTCB

GP4/BCKO

GP3/WSO

GP2/DO

GP1/DI

GP0/BCKI

GP5/WSI

61 15

14 13

10 7

64 2

TEST

CONTROL

BLOCK

SAMPLE FREQUENCY GENERATOR

D+

D−

20 17

ANALOG FRONT-END

USB-PROCESSOR

DIGITAL I/O

FIFO REGISTERS

AUDIO FEATURE

PROCESSING DSP

UP-SAMPLE FILTERS

MICRO-

CONTROLLER

UDA1331H

SCL

3 4

SDA EA

6 8

PSEN ALE

P2.0 P2.1

12 18

P2.2 P2.3

19 21

P2.4 P2.5

22 23

P2.6 P2.7

24 56

P0.0 P0.1

57 58

P0.2

P0.3 P0.4

60 62

P0.5 P0.6

P0.7

64f

SSX XTAL1 XTAL2

DDX

VOUTL

TIMING

OSC

38 39

VARIABLE HOLD REGISTER

128f

3rd-ORDER

NOISE SHAPER

LEFT

DAC

REFERENCE

VOLTAGE

42 V

Fig.1 Block diagram.

1998 Oct 06 4

ref

RIGHT

DAC

UDA1331H

32 30 29 25 51 49 45 44

MBK529

DDE

SSE

SSI

DDI

DDO

SSO

DDA

SSA

VOUTR

Philips Semiconductors Preliminary speciﬁcation

Universal Serial Bus (USB) Audio

UDA1331H

Playback Peripheral (APP)

PINNING

SYMBOL PIN I/O DESCRIPTION

n.c. 1 − not connected GP5/WSI 2 I/O general purpose pin 5 or word select input SCL 3 I/O serial clock input (I SDA 4 I/O serial data input/output (I P0.7 5 I/O Port 0.7 of the microcontroller EA 6 I/O external access (active LOW) GP1/DI 7 I/O general purpose pin 1 or data input PSEN 8 I/O program store enable (active LOW) ALE 9 I/O address latch enable (active HIGH) GP2/DO 10 I/O general purpose pin 2 or data output for extra DSP chip P2.0 11 I/O Port 2.0 of the microcontroller P2.1 12 I/O Port 2.1 of the microcontroller GP3/WSO 13 I/O general purpose pin 3 or master word select output for extra DSP chip GP4/BCKO 14 I/O general purpose pin 4 or master bit clock output for extra DSP chip SHTCB 15 I shift clock TCB input (active HIGH) n.c. 16 − not connected D− 17 I/O negative data line of the differential data bus conform to the USB-standard P2.2 18 I/O Port 2.2 of the microcontroller P2.3 19 I/O Port 2.3 of the microcontroller D+ 20 I/O positive data line of the differential data bus conform to the USB-standard P2.4 21 I/O Port 2.4 of the microcontroller P2.5 22 I/O Port 2.5 of the microcontroller P2.6 23 I/O Port 2.6 of the microcontroller P2.7 24 I/O Port 2.7 of the microcontroller V

DDI

25 − digital supply voltage core n.c. 26 − not connected n.c. 27 − not connected n.c. 28 − not connected V V

SSI SSE

29 − digital ground core

30 − digital ground I/O pins n.c. 31 − not connected V

DDE

32 − digital supply voltage I/O pins n.c. 33 − not connected n.c. 34 − not connected n.c. 35 − not connected V

SSX

36 − crystal oscillator ground XTAL1 37 I crystal oscillator input 1 XTAL2 38 O crystal oscillator output 2 V

DDX

39 − crystal oscillator supply voltage n.c. 40 − not connected

C-bus)

1998 Oct 06 5

Philips Semiconductors Preliminary speciﬁcation

Universal Serial Bus (USB) Audio Playback Peripheral (APP)

SYMBOL PIN I/O DESCRIPTION

n.c. 41 − not connected V

ref

n.c. 43 − not connected V

SSA

DDA

VOUTR 46 O right channel output voltage n.c. 47 − not connected n.c. 48 − not connected V

SSO

n.c. 50 − not connected V

DDO

n.c. 52 − not connected VOUTL 53 O left channel output voltage n.c. 54 − not connected TC 55 I test control input (active HIGH) P0.0 56 I/O Port 0.0 of the microcontroller P0.1 57 I/O Port 0.1 of the microcontroller P0.2 58 I/O Port 0.2 of the microcontroller P0.3 59 I/O Port 0.3 of the microcontroller P0.4 60 I/O Port 0.4 of the microcontroller RTCB 61 I asynchronous reset input for test control box (active HIGH) P0.5 62 I/O Port 0.5 of the microcontroller P0.6 63 I/O Port 0.6 of the microcontroller GP0/BCKI 64 I/O general purpose pin 0 or master bit clock input

42 O reference output voltage

44 − analog ground

45 − analog supply voltage

49 − operational ampliﬁer ground

51 − operational ampliﬁer supply voltage

UDA1331H

1998 Oct 06 6

Philips Semiconductors Preliminary speciﬁcation

Universal Serial Bus (USB) Audio Playback Peripheral (APP)

handbook, full pagewidth

P0.6

P0.5

n.c.

GP5/WSI

SCL SDA P0.7

GP1/DI

PSEN

ALE

GP2/DO

P2.0 P2.1

GP3/WSO

GP4/BCKO

SHTCB

n.c.

D− P2.2 P2.3

GP0/BCKI

64 1 2 3 4 5 6 7 8 9

10 11 12 13 14 15 16 17 18 19

RTCB 61

P0.4

P0.3

UDA1331H

P0.2 58

P0.1 57

P0.0 56

TC 55

n.c.

VOUTL 53

UDA1331H

DDO

n.c.

SSO

n.c.

VOUTR

DDA

SSA

n.c.

REF

n.c.

DDX

XTAL2

XTAL1

SSX

n.c.

D+

P2.4

P2.5

P2.6

P2.7

DDI

Fig.2 Pin configuration.

1998 Oct 06 7

n.c.

28 n.c.

SSI

SSE

n.c.

DDE

MBK528

Philips Semiconductors Preliminary speciﬁcation

Universal Serial Bus (USB) Audio Playback Peripheral (APP)

FUNCTIONAL DESCRIPTION All bold-faced parameters given in this data sheet

such as ‘bAlternateSetting’ are part of the USB specification as described in

Definition for Audio Devices”

The Universal Serial Bus (USB)

Data and power are transferred via the USB by a 4-wire cable. The signalling occurs via two wires and point-to-point segments. The signals on each segment are differentially driven into a cable of 90 Ω intrinsic impedance. The differential receiver features input sensitivity of at least 200 mV and sufficient common mode rejection.

The analog front-end

The analog front-end is an on-chip generic USB transceiver. It is designed to allow voltage levels up to V from standard or programmable logic to interface with the physical layer of the USB. It is capable of receiving and transmitting serial data at full speed (12 Mbits/s).

The USB processor

The USB processor forms the interface between the analog front-end, the ADAC and the microcontroller. The USB processor consists of:

• The Philips Serial Interface Engine (PSIE)

• The Memory Management Unit (MMU)

• The Audio Sample Redistribution (ASR) module.

“USB Device Class

UDA1331H

The PSIE is the digital front-end of the USB processor. This module recovers the 12 MHz USB clock, detects the USB sync word and handles all low-level USB protocols and error checking.

The MMU is the digital back-end of the USB processor. It handles the temporary data storage of all USB packets that are received or sent over the bus. Three types of packets are defined on the USB. These are:

• Token packets

• Data packets

• Handshake packets.

The token packet contains information about the destination of the data packet. The audio data is transferred via an isochronous data sink endpoint and consequently no handshaking mechanism is used. The MMU also generates a 1 kHz clock that is locked to the USB Start-Of-Frame (SOF) token.

HE AUDIO SAMPLE REDISTRIBUTION (ASR) MODULE

The ASR module reads the audio samples from the MMU and distributes these samples equidistant over a 1 ms frame period. The distributed audio samples are translated by the digital I/O module to standard I2S-bus format or Japanese digital I/O format. The ASR module generates the bit clock and the word select signal of the digital I/O. The digital I/O formats the received audio samples to one of the four speciﬁed serial digital audio formats (standard I2S-bus, 16, 18 or 20 bits LSB-justiﬁed).

The microcontroller

HE PHILIPS SERIAL INTERFACE ENGINE AND MEMORY

MANAGEMENT UNIT (PSIE AND MMU) The PSIE and MMU translate the electrical USB signals

into bytes and signals. Depending upon the USB device address and the USB endpoint address, the USB data is directed to the correct endpoint buffer on the PSIE and MMU interface. The data transfer could be of the bulk, isochronous, control or interrupt type. The USB device address is conﬁgured during the enumeration process. The UDA1331H has three endpoints. These are:

• Control endpoint 0

• Status interrupt endpoint

• Isochronous data sink endpoint.

The amount of bytes per packet on the control endpoint is limited by the PSIE and MMU hardware to 8 bytes per packet.

1998 Oct 06 8

The microcontroller receives the control information selected from the USB by the USB processor. It handles the high-level USB protocols and the user interfaces.

The major task of the software process, that is mapped upon the microcontroller, is to control the different modules of the UDA1331H in such a way that it behaves as a USB device. Therefore the microcontroller:

• Interprets the USB requests and maps them upon the UDA1331H application

• Controls the internal operation of the UDA1331H and the digital I/O pins

• Communicates with the external world (EEPROM) using

the I

C-bus facility and the general purpose I/O pins.

The firmware must be located in an external (E)PROM. The UDA1331H will be delivered with standard USB compliant firmware.

Philips Semiconductors Preliminary speciﬁcation

Universal Serial Bus (USB) Audio Playback Peripheral (APP)

The Asynchronous Digital-to-Analog Converter (ADAC)

The ADAC receives USB audio information from the USB processor or from the digital I/O-bus. The ADAC is able to reconstruct the sample clock from the rate at which the audio samples arrive and handles the audio sound processing. After processing, the audio signal is up-sampled, noise-shaped and converted to analog output voltages capable of driving a line output. The ADAC consists of:

• A Sample Frequency Generator (SFG)

• First-In First-Out (FIFO) registers

• An audio feature processing DSP

• Two digital up-sample filters

• A variable hold register

• A digital Noise Shaper (NS)

• A Filter Stream DAC (FSDAC) with integrated filter and

line output drivers.

THE SAMPLE FREQUENCY GENERATOR (SFG) The SFG controls the timing signals for the asynchronous

digital-to-analog conversion. By means of a digital PLL, the SFG automatically recovers the applied sampling frequency and generates the accurate timing signals for the audio feature processing DSP and the up-sample ﬁlters.

IRST-IN FIRST-OUT (FIFO) REGISTERS

F The FIFO registers are used to store the audio samples

temporarily coming from the USB processor or from the digital I/O input. The use of a FIFO register (in conjunction with the SFG) is necessary to remove all jitter present on the incoming audio signal.

HE AUDIO FEATURE PROCESSING DSP

A DSP processes the sound features. The control and mapping of the sound features is explained in Section “Controlling the USB Audio Playback Peripheral (APP)”. Depending on the sampling rate (fs) the DSP has four frequency domains in which the treble and bass are regulated (see Table 1). The domain is chosen automatically.

HE UP-SAMPLE FILTERS AND VARIABLE HOLD REGISTER

After the audio feature processing DSP two up-sample filters and a variable hold register increase the oversampling rate to 128fs.

UDA1331H

Table 1 Frequency domains for audio processing

DOMAIN SAMPLE FREQUENCY (kHz)

1 5 to 12 212to25 325to40 440to55

HE NOISE SHAPER

T A 3rd-order noise shaper converts the oversampled data

to a noise-shaped bitstream for the FSDAC. The in-band quantization noise is shifted to frequencies well above the audio band.

HE FILTER STREAM DAC (FSDAC)

The FSDAC is a semi-digital reconstruction filter that converts the 1-bit data stream of the noise shaper to an analog output voltage. The filter coefficients are implemented as current sources and are summed at virtual ground of the output operational amplifier. In this way very high signal-to-noise performance and low clock jitter sensitivity is achieved. A post filter is not needed because of the inherent filter function of the DAC. On-board amplifiers convert the FSDAC output current to an output voltage signal capable of driving a line output.

USB Audio Playback Peripheral (APP) descriptors

In a typical USB environment the USB host has to know which kind of devices are connected. For this purpose each device contains a number of USB descriptors. These descriptors describe, from different points of view (USB configuration, USB interface and USB endpoint), the capabilities of a device. Each of them can be requested by the host. The collection of descriptors is denoted as a descriptor map. This descriptor map will be reported to the USB host during enumeration and on request.

The full descriptor map is implemented in the firmware exploiting the full functionality of the UDA1331H. The USB descriptors and their most important fields, in relationship to the characteristics of the UDA1331H are briefly explained below.

ENERAL DESCRIPTORS

The UDA1331H supports one configuration containing a control interface, an audio interface and a HID interface. The descriptor map that describes this configuration is partly fixed and partly programmable.

1998 Oct 06 9

Philips Semiconductors Preliminary speciﬁcation

Universal Serial Bus (USB) Audio Playback Peripheral (APP)

handbook, full pagewidth

INPUT TERMINAL

Fig.3 Audio function topology.

The programmable part can be retrieved from one of four configuration maps located in the (E)PROM or from an I2C-bus EEPROM. At start-up one of four configuration maps can be selected depending on the logical combination of GP3 and GP0. It is possible to overwrite this configuration map with a configuration map loaded from an I2C-bus EEPROM.

UDIO DEVICE CLASS SPECIFIC DESCRIPTORS

The audio device class is partly specified with standard descriptors and partly with specific audio device class descriptors. The standard descriptors specify the number and the type of the interface or endpoint. The UDA1331H supports 7 different audio modes:

• 8-bit Pulse Code Modulation (PCM) mono or stereo audio data

• 16-bit PCM mono or stereo audio data

• 24-bit PCM mono or stereo audio data

• Zero bandwidth mode.

Each mode is defined as an alternate setting of the audio interface, selectable with the standard audio streaming interface descriptor bAlternateSetting field.

The seven alternate settings are described in more detail by the specific audio device class descriptors.

The UDA1331H supports the Input Terminal (IT), Output Terminal (OT) and the Feature Unit (FU) descriptors.

The input and output terminals are not controllable via the USB. The feature unit provides the basic manipulation of the incoming logical channels.

The supported sound features are:

• Volume control

• Mute control

• Treble control

• Bass control

• Bass boost control.

FEATURE UNIT

UDA1331H

OUTPUT TERMINAL

MBK530

Table 2 Audio bandwidth at each audio mode

AUDIO MODE wMaxPacketSize

8-bit PCM; mono 56 ( 8-bit PCM; stereo 112 ( 16-bit PCM; mono 112 ( 16-bit PCM; stereo 224 ( 24-bit PCM; mono 168 ( 24-bit PCM; stereo 336 (

The maximum number of audio data samples within a USB packet arriving on the isochronous sink endpoint is restricted by the buffer capacity of this isochronous endpoint. The maximum buffer capacity is 336 bytes/ms.

For each alternate setting with audio, a maximum bandwidth is claimed as indicated in the standard isochronous audio data endpoint descriptor wMaxPacketSize field. To allow a small overshoot in the number of audio samples per packet, the top sample frequency of 55 kHz is taken in the calculation of the bandwidth for each alternate setting. For each alternate setting, with its own isochronous audio data endpoint descriptor, wMaxPacketSize field is then defined as described in Table 2.

Although in a specific UDA1331H application no endpoint control properties can be used upon the isochronous adaptive sink endpoint, the descriptors are still necessary to inform the host about the definition of this endpoint: isochronous, adaptive, sink, continuous sampling frequency (at input side of this endpoint) with lower bound of 5 kHz and upper bound of 55 kHz.

The audio class specific descriptors can be requested with the ‘Get descriptor: configuration request’, which returns all the descriptors, except the device descriptor.

⁄8× 1 × 56)

⁄8× 2 × 56)

⁄8× 1 × 56)

⁄8× 2 × 56)

⁄8× 1 × 56)

⁄8× 2 × 56)

1998 Oct 06 10

Philips Semiconductors Preliminary speciﬁcation

Universal Serial Bus (USB) Audio Playback Peripheral (APP)

HUMAN INTERFACE DEVICE SPECIFIC DESCRIPTORS The inputs defined on the UDA1331H are transmitted via

the USB to the host according to the HID class. The host responds with the appropriate settings via the audio device class for the audio related parts or via the HID class for the HID related inputs and outputs of the UDA1331H.

A HID descriptor is necessary to inform the host about the conception of the user interface. The host communicates via the HID device driver using either the control pipe or the interrupt pipe. The UDA1331H uses USB endpoint 0 (control pipe) to respond to the HID specific ‘Get/set report request’ to receive or transmit data from or to the UDA1331H. The UDA1331H uses the status interrupt endpoint as interrupt pipe for polling asynchronous data.

The UDA1331H is a high-speed device. The maximum transaction size is 64 bytes per USB frame and the polling rate is defined at a maximum of every 1 ms.

The host requests the configuration descriptor which includes the standard interface descriptor, the HID endpoint descriptor and the HID descriptor. The HID device driver of the host then requests the report descriptor.

Report descriptors are composed of pieces of information about the device. Each piece of information is called an item. All items have a 1-byte prefix that contains the item tag, type and size. In the UDA1331H only the short item basic type is used.

The hosts HID device driver will parse the report descriptor and the defined items. By examining all of these items, the HID class driver is able to determine the size and composition of data reports from the device.

The main items of the UDA1331H are input and output reports. Input reports are sent via the interrupt pipe (UDA1331H USB address 3). Input and output reports can be requested by the host via the control endpoint (USB address 0).

The UDA1331H supports a maximum of three pushbuttons, which represents a certain feature of the UDA1331H. If pressed by the user the pushbutton will go to its ‘ON’ state, if not pressed the pushbutton will go back to its ‘OFF’ state. The UDA1331H supports a maximum of two outputs for e.g. user LEDs.

UDA1331H

Controlling the USB Audio Playback Peripheral (APP)

This section describes the functionality of the feature unit of the UDA1331H. The mapping of this functionality onto USB descriptors is as implemented in the firmware.

The sound features as defined in the

Definition for Audio Devices”

UDA1331H specific feature registers by the microcontroller. These specific sound features are:

• Volume control (separate for left and right stereo channels, no master channel)

• Mute control (only master channel)

• Treble control (only master channel)

• Bass control (only master channel)

• Dynamic bass boost control (only master channel).

These specific features can be activated via the host (audio device class requests) or via the GP pins (HID plus audio device class requests). Via the I2C-bus the user is able to download the necessary configuration data for different applications (definition of the function of the GP pins, with or without digital I/O functionality, etc.). The mapping and control of the standard USB audio features and UDA1331H specific features is described below.

OLUME CONTROL

Volume control is possible via the host or via predefined GP pins. The setting of 0 dB is always referenced to the maximum available volume setting. Table 3 gives the mapping of wVolume value (as defined in the

are mapped on the

Device Class Definition for Audio Devices”

actual volume setting of the USB APP. When using the UDA1331H, the range is 0 down to −60 dB (in steps of 1 dB) and −∞ dB. Independant control of ‘left’/’right’ volume is possible. It should be noted that wVolume bits B7 to B0 are not used. Values above 0 dB are returned as 0 dB. The volume value at start-up of the device is defined in the selected configuration map.

Balance control is possible via the separate volume control option of both channels. Therefore the characteristics of the balance control are equal to the volume control characteristics.

“USB Device Class

“USB

) upon the

For more information about the input and output functions of the UDA1331H see the application documentation of the device.

1998 Oct 06 11

Philips Semiconductors Preliminary speciﬁcation

Universal Serial Bus (USB) Audio

UDA1331H

Playback Peripheral (APP)

Table 3 Volume control characteristics

wVOLUME

B15 B14 B13 B12 B11 B10 B9 B8

00000000 0 0 11111111 −1 −1 11111110 −2 −2 11111101 −3 −3 11111100 −4 −4 11111011 −5 −5 11111010 −6 −6 11111001 −7 −7 11111000 −8 −8 11110111 −9 −9 11110110 −10 −10

... ... ... ... ... ... ... ... ... ...

11000101 −59 −59 11000100 −60 −60 11000011 −61 −∞ 11000010 −62 −∞

... ... ... ... ... ... ... ... ... ...

10000000 −∞ −∞

VOLUME USB SIDE

(dB)

VOLUME USB APP

(dB)

MUTE CONTROL Mute is one of the sound features as defined in the

Device Class Definition for Audio Devices”

control request data bMute controls the position of the mute switch. The position can be either on or off. When bMute is true the feature unit is muted. When bMute is false the feature unit is not muted.

When the mute is active for the master channel, the value of the sample is decreased smoothly to zero following a raised cosine curve. There are 32 coefficients used to step down the value of the data, each one being used 32 times before stepping to the next.

. The mute

“USB

This amounts to a mute transition of 23 ms at

= 44.1 kHz. When the mute is released, the samples are

returned to the full level again following a raised cosine curve with the same coefficients being used in reversed order. The mute, on the master channel is synchronized to the sample clock, so that operation always takes place on complete samples.

A mute can be given via the host or by pressing a predefined GP pin.

1998 Oct 06 12

+ 28 hidden pages

Philips UDA1331H Datasheet

Specifications and Main Features

Frequently Asked Questions

User Manual

Sound processing

Document references

APPLICATIONS

GENERAL DESCRIPTION

QUICK REFERENCE DATA

ORDERING INFORMATION

BLOCK DIAGRAM

PINNING

The Universal Serial Bus (USB)

The analog front-end

The USB processor

The microcontroller

The Asynchronous Digital-to-Analog Converter (ADAC)

USB Audio Playback Peripheral (APP) descriptors

Controlling the USB Audio Playback Peripheral (APP)