Philips TDA8786G-C2-S1, TDA8786G-C2, TDA8786G-C1-R5, TDA8786G-C1-S1, TDA8786G-C1 Datasheet

...
DATA SH EET
Product specification Supersedes data of 1997 May 20 File under Integrated Circuits, IC02
1997 Nov 17
INTEGRATED CIRCUITS
TDA8786; TDA8786A
1997 Nov 17 2
Philips Semiconductors Product specification
10-bit analog-to-digital interface for CCD cameras
TDA8786; TDA8786A
FEATURES
Correlated Double Sampling (CDS), AGC, soft clipper, pre-blanking, 10-bit ADC and reference regulator included
Fully programmable via a 3-wire serial interface
Sampling frequency up to 18 MHz
AGC gain from 3.5 to 33.5 dB (in 0.1 dB steps)
Programmable soft clipper for white compression
(starting at 40% of the input signal)
Standby mode available for each block for power saving applications (19 mW)
6 dB fixed gain analog output for analog iris control
8-bit and 10-bit DAC included for analog settings
Low power consumption of only 475 mW (typ.)
5 V operation and 2.5 to 5 V operation for the digital
outputs
CDS control pulse: TDA8786 = HIGH; TDA8786A = LOW
TTL compatible inputs, TTL and CMOS compatible outputs.
GENERAL DESCRIPTION
The TDA8786; TDA8786A is a 10-bit analog-to-digital interface for CCD cameras. The device includes a correlated double sampling circuit, AGC, a soft clipper circuit and a low power 10-bit Analog-to-Digital Converter (ADC) together with its reference voltage regulator.
The AGC and soft clipper circuits are controlled by on-chip DACs via a serial interface.
A 10-bit DAC controls the ADC input clamp level. A pre-blanking function is also included. An additional DAC is provided for additional system
controls; its output voltage range is 1.4 V (p-p) which is available at pin OFDOUT.
APPLICATIONS
CCD camera systems.
QUICK REFERENCE DATA
ORDERING INFORMATION
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
V
CCA
analog supply voltage 4.5 4.75 5.5 V
V
CCD
digital supply voltage 4.5 4.75 5.5 V
V
CCO
digital outputs supply voltage 2.5 2.6 5.5 V
I
CCA
analog supply current 83 mA
I
CCD
digital supply current 16 mA
I
CCO
digital outputs supply current f
CLK
= 18 MHz;
CL= 20 pF; ramp input
1 mA
ADC
res
ADC resolution 10 bits
V
i(CDS)(p-p)
CDS input voltage (peak-to-peak value) 400 1200 mV
G
CDS
CDS output amplifier gain 6 dB
f
CLK(max)
maximum clock frequency 18 −−MHz
AGC
dyn
AGC dynamic range 30 dB
N
tot(rms)
total noise from CDS input to ADC output (RMS value)
gain = 3.5 dB 0.5 LSB
P
tot
total power consumption 475 mW
TYPE
NUMBER
PACKAGE
NAME DESCRIPTION VERSION
TDA8786G
LQFP48 plastic low profile quad flat package; 48 leads; body 7 × 7 × 1.4 mm SOT313-2
TDA8786AG
1997 Nov 17 3
Philips Semiconductors Product specification
10-bit analog-to-digital interface for CCD cameras
TDA8786; TDA8786A
BLOCK DIAGRAM
Fig.1 Block diagram.
handbook, full pagewidth
MGE361
SOFT
CLIPPER
OPTICAL
BLACK CLAMP
TRACK-
AND-HOLD
TRACK-
AND-HOLD
TRACK-
AND-HOLD
TRACK-
AND-HOLD
TRACK-
AND-HOLD
CLAMP
ref2
ref1
CLAMP
CLAMP
8-BIT DAC
4-BIT DAC
10-BIT DAC
9-BIT DAC
+
6 dB
AGC
CLOCK
GENERATOR
10-BIT ADC
REGULATOR
SERIAL
INTERFACE
OUTPUTS
BUFFER
5
4
1
1
2
7
8
6
9 10
14
11
12
13 15 16 17 18
20
21
22
23
24
36
3
25
26
27
28
29
30
31
32
33
34
35
3738394041424344
454846
47
IN2
IN1 AGND3
V
CCA3
CDSP2 CDSP1 CLPCDS CLK
DGND2
V
CCD2
OE
V
CCO
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0 DGND1 OFDOUT
OGND
V
CCD1
STDBY
SEN
SCLK
SDATA
DEC1
V
RT
V
RB
V
CCA2
DACOUT
V
ref
CLPADC
AGND2
ADCIN
PBOUT
V
CCA1
PBIN
AGCOUT
PBK
CLPOPB
AGND1
19
STGE
AMPOUT
TDA8786
TDA8786A
1
1997 Nov 17 4
Philips Semiconductors Product specification
10-bit analog-to-digital interface for CCD cameras
TDA8786; TDA8786A
PINNING
SYMBOL PIN DESCRIPTION
CLPOPB 1 optical black clamp control pulse input (active HIGH for TDA8786, active LOW for TDA8786A) PBK 2 pre-blanking control pulse input; if PBK is HIGH (LOW) the signal is replaced by the optical
black level for TDA8786 (TDA8786A) OFDOUT 3 analog output of the additional 8-bit control DAC (controlled via the serial interface) AMPOUT 4 CDS amplifier output (fixed gain = +6 dB) AGND1 5 analog ground 1 V
CCA1
6 analog supply voltage 1 AGCOUT 7 AGC and soft clipper amplifier signal output PBIN 8 optical black clamp and pre-blanking block signal input (from AGCOUT via a capacitor) PBOUT 9 optical black clamp and pre-blanking block signal output ADCIN 10 ADC analog signal input (from PBOUT or AGCOUT via a capacitor) CLPADC 11 clamp control input for ADC analog input signal clamp (active HIGH for TDA8786 and active
LOW for TDA8786A)
V
ref
12 ADC input clamp reference voltage (normally connected to pin VRB or DACOUT) DACOUT 13 DAC output for ADC clamp level AGND2 14 analog ground 2 V
CCA2
15 analog supply voltage 2 V
RB
16 ADC reference voltage (BOTTOM) code 0 V
RT
17 ADC reference voltage (TOP) code 1023 DEC1 18 decoupling 1 (decoupled to ground via a capacitor) STGE 19 CDS offset storage SDATA 20 serial data input for the 4 control DACs (9-bit DAC for AGC gain, 4-bit DAC for soft clipper;
additional 8-bit DAC for OFD output voltage; 10-bit DAC for ADC clamp level and the stand-by
mode per block; see Table 1) SCLK 21 serial clock input for the control DACs and their serial interface; see Table 1 SEN 22 enable input for the serial interface shift register (active when SEN = logic 0); see Table 1 STDBY 23 stand-by control pin (active HIGH); all the output bits are logic 0 when stand-by is enabled V
CCD1
24 digital supply voltage 1 DGND1 25 digital ground1 D0 26 ADC digital output 0 (LSB) D1 27 ADC digital output 1 D2 28 ADC digital output 2 D3 29 ADC digital output 3 D4 30 ADC digital output 4 D5 31 ADC digital output 5 D6 32 ADC digital output 6 D7 33 ADC digital output 7 D8 34 ADC digital output 8 D9 35 ADC digital output 9 (MSB) OGND 36 digital output ground
1997 Nov 17 5
Philips Semiconductors Product specification
10-bit analog-to-digital interface for CCD cameras
TDA8786; TDA8786A
V
CCO
37 digital output supply voltage OE 38 output enable (LOW: digital outputs active; HIGH: digital outputs high impedance) V
CCD2
39 digital supply voltage 2 DGND2 40 digital ground2 CLK 41 ADC clock input CLPCDS 42 CDS clamp control input (active HIGH for TDA8786; active LOW for TDA8786A) CDSP1 43 CDS control pulse input 1 (active HIGH for TDA8786; active LOW for TDA8786A) CDSP2 44 CDS control pulse input 2 (active HIGH for TDA8786; active LOW for TDA8786A) V
CCA3
45 analog supply voltage 3 IN1 46 input signal 1 from CCD (usually black channel) IN2 47 input signal 2 from CCD (usually video channel) AGND3 48 analog ground 3
SYMBOL PIN DESCRIPTION
Fig.2 Pin configuration.
1 2 3 4 5 6 7 8
9 10 11
36 35 34 33 32 31 30 29 28 27 26
13
14
15
16
17
18
19
20
21
22
23
48
47
46
45
44
43
42
41
40
39
38
12
24 37
25
TDA8786
TDA8786A
MGE360
OGND D9 D8 D7
D5 D4 D3 D2 D1 D0 DGND1
CLPOPB
PBK OFDOUT AMPOUT
AGND1 V
CCA1
PBIN
PBOUT
CLPADC
V
ref
D6
IN2
IN1
V
CCA3
CDSP2
CDSP1
CLPCDS
DGND2
V
CCD2
OE
V
CCO
AGND3
CLK
AGCOUT
ADCIN
AGND2
V
CCA2
V
RB
V
RT
DEC1
STGE
SDATA
SEN
STDBY
V
CCD1
DACOUT
SCLK
1997 Nov 17 6
Philips Semiconductors Product specification
10-bit analog-to-digital interface for CCD cameras
TDA8786; TDA8786A
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134).
Note
1. The supply voltages V
CCA
, V
CCD
and V
CCO
may have any value between 0.3 and +7.0 V provided that the supply
voltage difference VCC remains as indicated.
HANDLING
Inputs and outputs are protected against electrostatic discharges in normal handling. However, to be totally safe, it is desirable to take normal precautions appropriate to handling integrated circuits.
THERMAL CHARACTERISTICS
SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT
V
CCA
analog supply voltage note 1 0.3 +7.0 V
V
CCD
digital supply voltage note 1 0.3 +7.0 V
V
CCO
output stages supply voltage note 1 0.3 +7.0 V
V
CC
supply voltage difference
between V
CCA
and V
CCD
1.0 +1.0 V
between V
CCA
and V
CCO
1.0 +4.0 V
between V
CCD
and V
CCO
1.0 +4.0 V
V
i
input voltage referenced to V
SSA
0.3 +7.0 V
V
CLK(p-p)
AC input voltage for switching (peak-to peak-value)
referenced to V
SSD
V
CCD
V
I
o
output current 10 mA
T
stg
storage temperature 55 +150 °C
T
amb
operating ambient temperature 20 +75 °C
T
j
junction temperature 150 °C
SYMBOL PARAMETER CONDITIONS VALUE UNIT
R
th(j-a)
thermal resistance from junction to ambient in free air 76 K/W
1997 Nov 17 7
Philips Semiconductors Product specification
10-bit analog-to-digital interface for CCD cameras
TDA8786; TDA8786A
CHARACTERISTICS
V
CCA=VCCD
= 4.75 V; V
CCO
= 2.6 V; f
CLK
= 18 MHz; T
amb
=25°C; unless otherwise specified.
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Supplies
V
CCA
analog supply voltage 4.5 4.75 5.5 V
V
CCD
digital supply voltage 4.5 4.75 5.5 V
V
CCO
digital outputs supply voltage
2.5 2.6 5.5 V
I
CCA
analog supply current 83 mA
I
CCD
digital supply current 16 mA
I
CCO
digital outputs supply current
CL= 20 pF on all data outputs; ramp input
1 mA
Digital inputs
C
LOCK INPUT: CLK (REFERENCED TO DGND)
V
IL
LOW-level input voltage 0 0.8 V
V
IH
HIGH-level input voltage 2.0 V
CCD
V
I
IL
LOW-level input current V
CLK
= 0.8 V 1 +1 µA
I
IH
HIGH-level input current V
CLK
= 2.0 V −−20 µA
Z
i
input impedance f
CLK
= 18 MHz 2 k
C
i
input capacitance f
CLK
= 18 MHz 2 pF INPUTS: CDSP1 AND CDSP2 V
IL
LOW-level input voltage 0 0.6 V
V
IH
HIGH-level input voltage 2.2 V
CCD
V
I
IL
LOW-level input current VIL= 0.6 V −−100 −µA
I
IH
HIGH-level input current VIH= 2.2 V 0 −µA INPUTS: SEN, STDBY, CLPCDS, CLPOPB, PBK AND CLPADC V
IL
LOW-level input voltage 0 0.6 V V
IH
HIGH-level input voltage 2.2 V
CCD
V
I
i
input current 2 +2 µA INPUTS: SEN, SDATA AND SCLK (see Fig.14) t
su1
SEN set-up time compared
to SCLK rising edge
4 ns
t
su2
SDATA set-up time
compared to SCLK rising
edge
4 ns
t
su3
SEN set-up time compared
to SCLK falling edge
4 ns
t
hd3
SEN hold time compared
to SCLK rising edge
4 ns
t
hd4
SDATA hold time
compared to SCLK rising
edge
4 ns
1997 Nov 17 8
Philips Semiconductors Product specification
10-bit analog-to-digital interface for CCD cameras
TDA8786; TDA8786A
Correlated Double Sampling; CDS
V
i(CDS)(p-p)
CDS input amplitude
(peak-to-peak value)
400 1200 mV
I
STGE,IN1,IN2
input current pins 19, 46
and 47
2 +2 µA
t
CDS(min)
CDS control pulses
minimum active time
(HIGH for TDA8786,
LOW for TDA8786A)
f
i(CDS1,2)=fCLK(pix)
V
i(CDS)(p-p)
= 1200 mV black-to-white transition in one pixel (±1 LSB typ.)
12 −−ns
t
hd1
hold time IN1 compared to control pulse CDSP1
see Fig.15 1 ns
t
hd2
hold time of IN2 compared to control pulse CDSP2
see Fig.15 −−0.5 ns
Amplifier outputs
G
AMPOUT
output amplifier gain 6 dB
Z
AMPOUT
output amplifier impedance
300 −Ω
V
AMPOUT(p-p)
output amplifier dynamic voltage level (peak-to-peak value)
2.4 V
V
AMPOUT(bl)
output amplifier black level voltage
1.1 V
V
AGCOUT(p-p)
AGC output amplifier dynamic voltage level (peak-to-peak value)
1800 mV
V
AGCOUT
AGC output amplifier black level voltage
1.1 V
Z
AGCOUT
AGC output amplifier output impedance
at 10 kHz 5 −Ω
I
AGCOUT
AGC output static drive current
static −−1mA
V
OPB(p-p)
optical black clamp and blanking block output dynamic voltage (peak-to-peak value)
1.8 V
V
OPB
optical black clamp and blanking block output black level voltage
1.4 V
Z
OPB
optical black clamp and blanking block output impedance
at 10 kHz −−5
I
OPB
OPB output current drive static −−1mA
I
PBIN
input current pin 8 2 +2 µA
G
AGC(min)
minimum gain of AGC circuit
AGC DAC input code = 00 (9-bit control)
3.5 dB
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
1997 Nov 17 9
Philips Semiconductors Product specification
10-bit analog-to-digital interface for CCD cameras
TDA8786; TDA8786A
G
AGC(max)
maximum gain of AGC circuit
AGC DAC input code = 319 (9-bit control)
33.5 dB
V
AGCOUT
AGC output amplifier black level voltage
1.1 V
V
inflex(p-p)
voltage at soft clipper inflexion point (peak-to-peak value)
soft clipper 4-bit control DAC input code = 00
40% V
AGCOUT(p-p)
V
soft clipper 4-bit control DAC input code = 15
100% V
AGCOUT(p-p)
V
CR
sc
soft clipper compression ratio
V
i(sc)<Vinflex
1.0
V
i(sc)>Vinflex
0.66
CLAMPS
g
mADC
ADC clamps transconductance
at clamp level 60 mS
g
mPBK
PBK clamp transconductance
at clamp level 60 mS
g
mCDS
CDS clamps transconductance
at clamp level 5.5 mS
V
PBIN(clamp)
clamp voltage at PBIN input
1.4 V
Analog-to-Digital Converter; ADC
f
CLK(max)
maximum clock frequency 18 −−MHz
t
CPH
clock pulse width HIGH 15 −−ns
t
CPL
clock pulse width LOW 15 −−ns
SR
CLK
clock input slew rate (rising and falling edge)
10 to 90% 0.5 −−V/ns
V
i(ADC)(p-p)
ADC input voltage level (peak-to-peak value)
1.8 V
V
RB
ADC reference voltage output code 0
1.4 V
V
RT
ADC reference voltage output code 1023
3.2 V
I
ADCIN
input current pin 10 2 +2 µA
ILE integral linearity error f
CLK
= 18 MHz; ramp input −±1.0 ±2.0 LSB
DLE differential linearity error f
CLK
= 18 MHz; ramp input −±0.4 ±0.75 LSB
t
d(s)
sampling delay time −−5ns
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Loading...
+ 19 hidden pages