Philips tda8752 DATASHEETS

INTEGRATED CIRCUITS

DATA SH EET

TDA8752

Triple high speed Analog-to-Digital
Converter (ADC)

Product specification
Supersedes data of 1998 Aug 11
File under Integrated Circuits, IC02

1999 Mar 09

Philips Semiconductors Product specification

Triple high speed Analog-to-Digital
Converter (ADC)

FEATURES

• Triple 8-bit ADC

• Sampling rate up to 100 MHz

• IC controllable via a serial interface, which can be either

I2C-bus or 3-wire, selected via a TTL input pin

• IC analog voltage input from 0.4 to 1.2 V (p-p) to
produce full-scale ADC input of 1 V (p-p)

• 3 clamps for programming a clamping code between

−63.5 and +64 in steps of1⁄2LSB

• 3 controllable amplifiers: gain controlled via the serial

interface to produce a full scale resolution of
peak-to-peak

• Amplifier bandwidth of 250 MHz

• Low gain variation with temperature

• PLL, controllable via the serial interface to generate the

ADC clock, which can be locked to a line frequency from
15 to 280 kHz

• Integrated PLL divider

• Programmable phase clock adjustment cells

• Internal voltage regulators

• TTL compatible digital inputs and outputs

• Chip enable high-impedance ADC output

• Power-down mode

• Possibility to use up to four ICs in the same system,

using the I2C-bus interface, or more, using the 3-wire
serial interface

• 1 W power dissipation.

1

⁄2LSB

TDA8752

GENERAL DESCRIPTION

The TDA8752 is a triple 8-bit ADC with controllable
amplifiers and clamps for the digitizing of large bandwidth
RGB signals.

The clamp level, the gain and all of the other settings are
controlled via a serial interface (either I
serial bus, selected via a logic input).

The IC also includes a PLL that can be locked on the
horizontal line frequency and generates the ADC clock.
The PLL jitter is minimized for high resolution PC graphics
applications. An external clock can also be input to the
ADC.

It is possible to set the TDA8752 serial bus address
between four fixed values, in the event that several
TDA8752 ICs are used in a system, using the I
interface (for example, two ICs used in an odd/even
configuration).

2

C-bus or 3-wire

2

C-bus

APPLICATIONS

• R, G and B high speed digitizing

• LCD panels drive

• LCD projection systems

• VGA and higher resolutions

• Using two ICs in parallel, higher display resolution can

be obtained; 200 MHz pixel frequency.

ORDERING INFORMATION

TYPE

NUMBER

TDA8752H/6
TDA8752H/8 100

1999 Mar 09 2

NAME DESCRIPTION VERSION

QFP100

plastic quad flat package; 100 leads (lead length 1.95 mm);
body 14 × 20 × 2.8 mm

PACKAGE SAMPLING

FREQUENCY

(MHz)

SOT317-2

60

Philips Semiconductors Product specification

Triple high speed Analog-to-Digital

TDA8752

Converter (ADC)

QUICK REFERENCE DATA

SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT

V

CCA

V

DDD

V

CCD

V

CCO

V

CCA(PLL)

V

CCO(PLL)

I

CCA

I

DDD

I

CCD

I

CCO

I

CCA(PLL)

I

CCO(PLL)

f

CLK

f

ref(PLL)

f

VCO

INL DC integral non linearity from analog input to

DNL DC differential non linearity from analog input to

∆G

amp

B amplifier bandwidth −3 dB; T
t

set

DR

PLL

P

tot

j

PLL(rms)

analog supply voltage for R, G and B channels 4.75 5.0 5.25 V
logic supply voltage for I2C-bus and 3-wire 4.75 5.0 5.25 V
digital supply voltage 4.75 5.0 5.25 V
output stages supply voltage for R, G and B channels 4.75 5.0 5.25 V
analog PLL supply voltage 4.75 5.0 5.25 V
output PLL supply voltage 4.75 5.0 5.25 V
analog supply current − 120 − mA
logic supply current for I2C-bus and 3-wire − 1.0 − mA
digital supply current − 40 − mA
output stages supply current f

= 100 MHz;

CLK

− 6 − mA

ramp input
analog PLL supply current − 28 − mA
output PLL supply current − 5 − mA
maximum clock frequency TDA8752/6 60 −−MHz

TDA8752/8 100 −−MHz
PLL reference clock frequency 15 − 280 kHz
VCO output clock frequency 12 − 100 MHz

−±0.5 ±1.5 LSB
digital output; full-scale;
ramp input;
f

= 100 MHz

CLK

−±0.5 ±1.0 LSB
digital output; full-scale;
ramp input;

= 100 MHz

f

CLK

/T amplifier gain stability as a function of

temperature

settling time of the ADC block plus AGC input signal settling

V

= 2.5 V with

ref

100 ppm/°C maximum

=25°C 250 −−MHz

amb

time < 1 ns; T

amb

=25°C

−−200 ppm/°C

−−6ns

PLL divider ratio 100 − 4095
total power consumption f

= 100 MHz;

CLK

− 1.0 − W
ramp input

maximum PLL phase jitter (RMS value) f

= 66.67 kHz;

ref

f

= 100 MHz

CLK

− 0.3 − ns

1999 Mar 09 3

This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in

bo

_white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in

white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ...

1999 Mar 09 4

ok, full pagewidth

BLOCK DIAGRAM

Triple high speed Analog-to-Digital

Converter (ADC)

Philips Semiconductors Product specification

RAGC

RGAINC

RIN

RDEC

V

ref

GAGC

GGAINC

GIN

GDEC

BAGC

BGAINC

BIN

BDEC

TDO

TCK
ADD2
ADD1

SEN

SCL

SDA

DIS

2

I

C/3W

V

6
8

12
10

3

14
16

20
18

22
24

28
26

36
35

34
33
38
42
39
37
32

V

CCAR

V

CCAG

11

19

INTERFACE

1, 5, 30, 31, 43 , 44
50, 51, 100

CCAB

V

27

SERIAL

2

I

C-BUS

OR

3-WIRE

DDD

40

V

CCOR

V

79

MUX

V

CCOG

69

CCOB

V

59

HSYNCI

2

I

C-bus; 1-bit

(H level)

90

V

CCA(PLL)

V

CCD

CCO(PLL)

95

99

RED CHANNEL

GREEN CHANNEL

BLUE CHANNEL

TDA8752

REGULATOR

4 2 88 97 98

CLP

85

CLAMP

AGNDR

89

DEC2DEC1HSYNCn.c.

AGNDG

13

PWDWN

AGNDB

21

29

V

SSD

ADC

CP

OGNDR

41

PLL

OGNDG

70

OUTPUTS

CZ

OGNDB

60

AGNDPLL

OGNDPLL

96

48

DGND

86

82

71 to 78

45

17
15

61 to 68

46
87

25
23

49, 52 to 58

47

84
83

81
80

92
91
93
94

MGG363

9
7

RCLP

RBOT

R0 to R7

ROR

GCLP
GBOT

G0 to G7
GOR

OE
BCLP
BBOT

B0 to B7
BOR

CKADCO
CKBO

CKAO
CKREFO

CKEXT
INV
COAST
CKREF

TDA8752

Fig.1 Block diagram.

Philips Semiconductors Product specification

Triple high speed Analog-to-Digital
Converter (ADC)

CLP RAGC CLKADC

handbook, full pagewidth

RCLP

V

ref

RIN

V

P

150

kΩ

3
kΩ

45
kΩ

DAC

5

REGISTER

FINE GAIN ADJUST

I2C-bus; 5 bits

(Fr)

MUX

CLAMP

CONTROL

AGC

V

CCAR

ADC

ADC

8

D

D ≥ R

R

1

1

COARSE GAIN ADJUST

8

7

REGISTER

2

I

C-bus; 7 bits

(Cr)

DAC

REGISTER

2

I

C-bus; 8 bits

(Or)

TDA8752

8

ROR

8

OUTPUTS

SERIAL

2

I

C-BUS

R0 to R7

OE

RBOT

HSYNCI

RGAINC

Fig.2 Red channel diagram.

1999 Mar 09 5

MGG364

Philips Semiconductors Product specification

Triple high speed Analog-to-Digital
Converter (ADC)

handbook, full pagewidth

CKREF

edge selector

2

I

C-bus;
1 bit
(edge)

2

I

C-bus; 1 bit

(V level)

COAST

PHASE

FREQUENCY

DETECTOR

2

I

C-bus; 5 bits

(Ip, Up, Do)

DIV N (100 to 4095)

2

I

C-bus; 12 bits (Di)

C

z

CZ CP

loop filter

2

I

C-bus;

3 bits (Z)

2 bits (VCO)

C

p

VCO

2

I

C-bus;

12 to

100 MHz

phase selector A

2

I

C-bus;

5 bits (Pa)

phase selector B

2

I

C-bus; 5 bits (Pb)

CKEXT INV

MUX

2

I

C-bus;

1 bit (Cka)

0°/180°

CLK
ADC

TDA8752

2

C-bus;

I

1 bit (Ckb)

CKADCO

CKBO

CKAO

Fig.3 PLL diagram.

SYNCHRO

CKREFO

MGG370

1999 Mar 09 6

Philips Semiconductors Product specification

Triple high speed Analog-to-Digital

TDA8752

Converter (ADC)

PINNING

SYMBOL PIN DESCRIPTION

n.c. 1 not connected
DEC2 2 main regulator decoupling input
V

ref

DEC1 4 main regulator decoupling input
n.c. 5 not connected
RAGC 6 red channel AGC output
RBOT 7 red channel ladder decoupling input (BOT)
RGAINC 8 red channel gain capacitor input
RCLP 9 red channel gain clamp capacitor input
RDEC 10 red channel gain regulator decoupling input
V

CCAR

RIN 12 red channel gain analog input
AGNDR 13 red channel gain analog ground
GAGC 14 green channel AGC output
GBOT 15 green channel ladder decoupling input (BOT)
GGAINC 16 green channel gain capacitor input
GCLP 17 green channel gain clamp capacitor input
GDEC 18 green channel gain regulator decoupling input
V

CCAG

GIN 20 green channel gain analog input
AGNDG 21 green channel gain analog ground
BAGC 22 blue channel AGC output
BBOT 23 blue channel ladder decoupling input (BOT)
BGAINC 24 blue channel gain capacitor input
BCLP 25 blue channel gain clamp capacitor input
BDEC 26 blue channel gain regulator decoupling input
V

CCAB

BIN 28 blue channel gain analog input
AGNDB 29 blue channel gain analog ground
n.c. 30 not connected
n.c. 31 not connected
I2C/3W 32 selection input between I2C-bus (active HIGH) and 3-wire serial bus (active LOW)
ADD1 33 I2C-bus address control input 1
ADD2 34 I2C-bus address control input 2
TCK 35 scan test mode (active HIGH)

3 gain stabilizer voltage reference input

11 red channel gain analog power supply

19 green channel gain analog power supply

27 blue channel gain analog power supply

1999 Mar 09 7

Philips Semiconductors Product specification

Triple high speed Analog-to-Digital
Converter (ADC)

SYMBOL PIN DESCRIPTION

TDO 36 scan test output
DIS 37 I2C and 3W disable control input (disable at HIGH level)
SEN 38 select enable for 3-wire serial bus input (see Fig.10)
SDA 39 I2C/3W serial data input
V

DDD

V

SSD

SCL 42 I
n.c. 43 not connected
n.c. 44 not connected
ROR 45 red channel ADC output bit out of range
GOR 46 green channel ADC output bit out of range
BOR 47 blue channel ADC output bit out of range
OGNDB 48 blue channel ADC output ground
B0 49 blue channel ADC output bit 0 (LSB)
n.c. 50 not connected
n.c. 51 not connected
B1 52 blue channel ADC output bit 1
B2 53 blue channel ADC output bit 2
B3 54 blue channel ADC output bit 3
B4 55 blue channel ADC output bit 4
B5 56 blue channel ADC output bit 5
B6 57 blue channel ADC output bit 6
B7 58 blue channel ADC output bit 7 (MSB)
V

CCOB

OGNDG 60 green channel ADC output ground
G0 61 green channel ADC output bit 0 (LSB)
G1 62 green channel ADC output bit 1
G2 63 green channel ADC output bit 2
G3 64 green channel ADC output bit 3
G4 65 green channel ADC output bit 4
G5 66 green channel ADC output bit 5
G6 67 green channel ADC output bit 6
G7 68 green channel ADC output bit 7 (MSB)
V

CCOG

OGNDR 70 red channel ADC output ground
R0 71 red channel ADC output bit 0 (LSB)

40 logic I2C/3W digital power supply
41 logic I2C/3W digital ground

2

C/3W serial clock input

59 blue channel ADC output power supply

69 green channel ADC output power supply

TDA8752

1999 Mar 09 8

Philips Semiconductors Product specification

Triple high speed Analog-to-Digital
Converter (ADC)

SYMBOL PIN DESCRIPTION

R1 72 red channel ADC output bit 1
R2 73 red channel ADC output bit 2
R3 74 red channel ADC output bit 3
R4 75 red channel ADC output bit 4
R5 76 red channel ADC output bit 5
R6 77 red channel ADC output bit 6
R7 78 red channel ADC output bit 7 (MSB)
V

CCOR

CKREFO 80 reference output clock resynchronized horizontal pulse
CKAO 81 PLL clock output 3 (in phase with reference output clock)
OGNDPLL 82 PLL digital ground
CKBO 83 PLL clock output 2
CKADCO 84 PLL clock output 1 (in phase with internal ADC clock)
V

CCO(PLL)

DGND 86 digital ground
OE 87 output enable not (when OE is HIGH, the outputs are in high-impedance)
PWDWN 88 power-down control input (IC is in power-down mode when this pin is HIGH)
CLP 89 clamp pulse input (clamp active HIGH)
HSYNC 90 horizontal synchronization input pulse
INV 91 PLL clock output inverter command input (invert when HIGH)
CKEXT 92 external clock input
COAST 93 PLL coast command input
CKREF 94 PLL reference clock input
V

CCD

AGNDPLL 96 PLL analog ground
CP 97 PLL filter input
CZ 98 PLL filter input
V

CCAPLL

n.c. 100 not connected

79 red channel ADC output power supply

85 PLL output power supply

95 digital power supply

99 PLL analog power supply

TDA8752

1999 Mar 09 9

Philips Semiconductors Product specification

Triple high speed Analog-to-Digital
Converter (ADC)

handbook, full pagewidth

n.c.

DEC2

V

ref

DEC1

n.c.
RAGC
RBOT

RGAINC

RCLP

RDEC

V

CCAR

RIN

AGNDR

GAGC

GBOT

GGAINC

GCLP
GDEC

V

CCAG

GIN

AGNDG

BAGC
BBOT

BGAINC

BCLP

BDEC

V

CCAB

BIN

AGNDB

n.c.

CCA(PLL)

n.c.

V

CZCPAGNDPLL

99989796959493929190898887868584838281

100

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15
16
17
18
19

20
21
22
23
24
25
26
27
28
29
30

CCD

V

CKREF

COAST

CKEXT

INV

HSYNC

TDA8752

CLP

PWDWNOEDGND

CCO(PLL)

V

CKADCO

CKBO

OGNDPLL

CKAO

80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51

CKREFO
V

CCOR

R7
R6
R5
R4
R3
R2
R1
R0
OGNDR

V

CCOG

G7
G6
G5
G4
G3
G2
G1
G0
OGNDG

V

CCOB

B7
B6
B5
B4
B3
B2
B1
n.c.

TDA8752

31323334353637383940414243444546474849

n.c.

C/3W

2

I

ADD1

ADD2

TCK

TDO

DIS

SEN

SDA

V

Fig.4 Pin configuration.

1999 Mar 09 10

DDD

SSD

V

SCL

n.c.

n.c.

ROR

GOR

BOR

B0

OGNDB

50

n.c.

MGG362

Philips Semiconductors Product specification

Triple high speed Analog-to-Digital
Converter (ADC)

FUNCTIONAL DESCRIPTION

This triple high-speed 8-bit ADC is designed to convert
RGB signals, from a PC or work station, into data used by
a LCD driver (pixel clock up to 200 MHz, using 2 ICs).

IC analog video inputs

The video inputs are internally DC polarized. These inputs
are AC coupled externally.

Clamps

Three independent parallel clamping circuits are used to
clamp the video input signals on the black level and to
control the brightness level. The clamping code is
programmable between code −63.5 and +64 in steps of

1

⁄2LSB. The programming of the clamp value is achieved

via an 8-bit DAC. Each clamp must be able to correct an
offset from±0.1 V to±10 mV within 300 ns, and correct the
total offset in 10 lines.

The clamps are controlled by an external TTL positive
going pulse (pin CLP). The drop of the video signal is
<1 LSB.

Normally, the circuit operates with a 0 code clamp,
corresponding to the 0 ADC code. This clamp code can be
changed from −63.5 to +64 as represented in Fig.7,
in steps of1⁄2LSB. The digitized video signal is always
between code 0 and code 255 of the ADC.

TDA8752

The output of the multiplexer is either the normal video
signal or the 0.156 V reference signal (during HSYNC).

The corresponding ADC outputs are then compared to a
pre-set value loaded in a register. Depending on the result
of the comparison, the gain of the variable gain amplifiers
is adjusted (coarse gain control; see Figs 2 and 8).
The three 7-bit registers receive data via a serial interface
to enable the gain to be programmed.

The pre-set value loaded in the 7-bit register is chosen
between approximately 67 codes to ensure the full-scale
input range (see Fig.8). A contrast control can be achieved
using these registers. In this case care should be taken to
stay within the allowed code range (32 to 99).

A fine correction using three 5-bit DACs, also controlled via
the serial interface, is used to finely tune the gain of the
three channels (fine gain control; see Figs 2 and 9) and to
compensate the channel-to-channel gain mismatch.

With a full scale ADC input, the resolution of the fine
register corresponds to

To use these gain controls correctly, it is recommended to
fix the coarse gain (to have a full-scale ADC input signal)
to within 4LSB and then adjust it with the fine gain.
The gain is adjusted during HSYNC. During this time the
output signal is not related to the amplified input signal.
The outputs, when the coarse gain system is stable, is
related to the programmed coarse code (see Fig.8).

1

⁄2LSB peak-to-peak variation.

Variable gain amplifier

Three independent variable gain amplifiers are used to
provide, to each channel, a full-scale input range signal to
the 8-bit ADC. The gain adjustment range is designed so
that, for an input range varying from 0.4 to 1.2 V (p-p), the
output signal corresponds to the ADC full-scale input of
1 V (p-p).

To ensure that the gain does not vary over the whole
operating temperature range, an external reference of
+2.5 V DC, (V
supplied externally, is used to calibrate the gain at the
beginning of each video line before the clamp pulse using
the following principle.

A differential of 0.156 V (p-p) (1⁄16V
generated internally from the reference voltage (V
During the synchronization part of the video line, the
multiplexer, controlled by the TTL synchronization signal
(HSYNCI, coming from HSYNC; see Fig.1) with a width
equal to one of the video synchronization signals
(e.g. signal coming from a synchronization separator), is
switched between the two amplifiers.

1999 Mar 09 11

with a 100 ppm/°C maximum variation)

ref

) reference signal is

ref

ref

).

ADCs

The ADCs are 8-bit with a maximum clock frequency of
100 Msps. The ADCs input range is 1 V (p-p) full-scale.
One out of range bit exists per channel (ROR, GOR and
BOR). It will be at logic 1 when the signal is out of range of
the full scale of the ADCs.

Pipeline delay in the ADCs is 1 clock cycle from sampling
to data output.

The ADCs reference ladders regulators are integrated.

ADC outputs

ADC outputs are straight binary. An output enable pin
(

OE; active LOW) enables the output status between
active and high-impedance (OE = HIGH) to be switched;
it is recommended to load the outputs with a 10 pF
capacitive load. The timing must be checked very carefully
if the capacitive load is more than 10 pF.