Philips TAB8507 User manual

Soundbar

8000 Series

TAB8507

User manual

Register your product and get support at

www.philips.com/support

Contents

1 Important safety instructions 3

Safety 3
Care for your product 4
Care of the environment 4
Declaration of conformity 5
Help and support 5
FCC information 6

2 Your Soundbar 7

What’s in the box 7
Soundbar 7
Connectors 8
Wireless subwoofer 9
Remote control 9
Prepare the remote control 10
Placement 11
Wall mount 12

3 Connect 13

Dolby Atmos® 13
Connect to HDMI socket 13
Connect to Optical socket 14
Connect to Audio in socket 14
Connect to power 15
Pair up with the subwoofer 15
Connect to Wi-Fi

(Wireless operation) 16

Connect the soundbar to Philips

Play- enabled TV 18

5 Product specications

25

6 Troubleshooting 27

Trademarks: 29

4 Use your soundbar 19

Turn ON and OFF 19

Select modes 20
Adjust the volume 20
Enjoy Dolby Atmos sound 20
Setup menu 20
Play from Bluetooth devices 23
Listen to an external device 23
Play audio through USB 24
Factory reset 24

2 EN

1 Important

safety
instructions

Read and understand all instructions
before you use your product. If damage is
caused by failure to follow instructions, the
warranty does not apply.

Safety

Know these safety symbols

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.

This is CLASS II apparatus with

double insulation, and no
protective earth provided.

AC voltage

Follow the instructions in the user

manual!

WARNING!

Warning: Risk of electric shock!

The exclamatory mark is intended

to alert the user to the presence of
important operating instructions.

Risk of electric shock or re!

• Before you make or change any
connections, make sure that all
devices are disconnected from the
power outlet.

• Never expose the product and
accessories to rain or water. Never

place liquid containers, such as vases,
near the product. If liquids are spilt on

or into the product, disconnect it from
the power outlet immediately. Contact
Consumer Care to have the product
checked before use.

• Never place the product and
accessories near naked ames or other

heat sources, including direct sunlight.

• Never insert objects into the

ventilation slots or other openings
on the product.

• Where the mains plug or an
appliance coupler is used as the
disconnect device, the disconnect
device shall remain readily operable.

• Battery (battery pack or batteries
installed) shall not be exposed to

excessive heat such as sunshine, re

or the like.

• Disconnect the product from the
power outlet before lightning storms.

• When you disconnect the power cord,
always pull the plug, never the cable.

• Use the product in tropical and/or
moderate climates.

Risk of short circuit or re!

• For identication and supply ratings,

see the type plate at the back or
bottom of the product.

• Before you connect the product to the
power outlet, ensure that the power
voltage matches the value printed on
the back or bottom of the product.

Never connect the product to the
power outlet if the voltage is dierent.

Risk of injury or damage to this

product!

• For wall mounting, this product must
be securely attached to the wall in
accordance with the installation
instructions. Use only the supplied
wall mount bracket (if available).
Improper wall mounting may result
in accident, injury or damage. If you
have any query, contact Consumer
Care in your country.

3EN

• Never place the product or any

objects on power cords or on other
electrical equipment.

• If the product is transported in
temperatures below 5°C, unpack
the product and wait until its
temperature matches room
temperature before connecting it to
the power outlet.

• Parts of this product can be made
of glass. Handle with care to avoid
injury and damage.

Risk of overheating!

• Never install this product in a
conned space. Always leave a

space of at least four inches around
the product for ventilation. Ensure
curtains or other objects never cover
the ventilation slots on the product.

Risk of contamination!

• Do not mix batteries (old and new or
carbon and alkaine, etc.).

• CAUTION: Danger of explosion if

batteries are incorrectly replaced.
Replace only with the same or
equivalent type.

• Remove batteries if they are
exhausted or if the remote control is
not to be used for a long time.

• Batteries contain chemical
substances, they should be disposed
of properly.

Note

•

The rating label is pasted on the bottom or back

of the equipment.

Care for your product

Use only microber cloth to clean the

product.

Care of the environment

Disposal of your old product and
battery

Your product is designed and

manufactured with high quality
materials and components, which
can be recycled and reused.

This symbol on a product means

that the product is covered by
European Directive 2012/19/EU.

This symbol means that the

product contains batteries covered
by European Directive 2013/56/EU
which cannot be disposed of with
normal household waste.

Inform yourself about the local separate
collection system for electrical and
electronic products and batteries.
Follow local rules and never dispose of
the product and batteries with normal
household waste. Correct disposal
of old products and batteries helps
prevent negative consequences for the
environment and human health.

Removing the disposable batteries

To remove the disposable batteries, see

battery installation section.

4 EN

EN

For 5G Wi-Fi Device

The device for operation in the

band 5150–5350 MHz is only for
indoor use to reduce the potential
for harmful interference to co­channel mobile satellite systems.

FR

Pour un appareil Wi-Fi 5G

les dispositifs fonctionnant dans
la bande 5150-5350 MHz sont
réservés uniquement pour une

utilisation à l’intérieur an de

réduire les risques de brouillage
préjudiciable aux systèmes de
satellites mobiles utilisant les
mêmes canaux.

Declaration of conformity

This product complies with the radio

interference requirements of the
European community.

Hereby, MMD Hong Kong Holding

Limited declares that the product
is in compliance with the essential
requirements and other relevant
provisions of RED Directive 2014/53/EU

and UK Radio Equipment Regulations
SI 2017 No 1206. You can nd the

Declaration of Conformity on
www.philips.com/support.

Help and support

For extensive online support, visit

www.philips.com/support to:

• download the user manual and the
quick start guide

• watch video tutorials (available only
for selected models)

• nd answers to frequently answered
questions (FAQs)

• email us a question

• chat with our support representative.

Follow the instructions on the website
to select your language, and then enter
your product model number.

Alternatively, you can contact Consumer
Care in your country. Before you contact,
note down the model number and serial

number of your product. You can nd

this information on the back or bottom
of your product.

5EN

FCC information

NOTE: This equipment has been tested

and found to comply with the limits
for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits

are designed to provide reasonable
protection against harmful interference

in a residential installation. This

equipment generates, uses and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.

However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio
or television reception, which can be
determined by turning the equipment

o and on, the user is encouraged to

try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving
antenna.

• Increase the separation between the
equipment and receiver.

• Connect the equipment into an

outlet on a circuit dierent from that

to which the receiver is connected.

• Consult the dealer or an experienced

radio / TV technician for help.

FCC&IC Warning:

• This equipment should be installed

and operated with minimum
distance 20cm between the radiator
& your body.

• Changes or modications to this unit

not expressly approved by the party
responsible for compliance could
void the user’s authority to operate
the equipment.

FCC & IC Attention

• Cet appareil est conforme à FCC et

IC l’exposition aux rayonnements

limites xées pour un environnement

non contrôlé. Cet appareil doit être
installé et utilisé avec une distance
minimale de 20 cm entre le radiateur
et votre corps. Cet transmetteur ne
doit pas être co-situé ou opérant en
liaison avec toute autre antenne ou
transmetteur.

• Des câbles blindés doivent être
utilisés avec cet apparei l pour
assurer la conformité avec les
limites de la classe B de la FCC.

fonctionnement de I’appareil.

IC-Canada: CAN ICES-003(B)/NMB-003(B)

This device contains licence-exempt

transmitter(s) / receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt
RSS(s). Operation is subject to the

following two conditions:

1. This device may not cause
interference.

2. This device must accept any interference,
including interference that may cause
undesired operation of the device.

Avis d’Industrie Canada: CAN ICES-003(B)/

NMB-003(B)

L’émetteur/récepteur exempt de licence
contenu dans le présent appareil est

conforme aux CNR d’Innovation, Sciences

et Développement économique Canada
applicables aux appareils radio exempts
de licence. L’exploitation est autorisée

aux deux conditions suivantes :

1. L’appareil ne doit pas produire de

brouillage;

2. L’appareil doit accepter tout

brouillage radioélectrique subi, même
si le brouillage est susceptible d’en

compromettre le fonctionnement.

6 EN

2 Your Soundbar

s

Congratulations on your purchase,

and welcome to Philips! To fully
benet from the support that Philips
oers, register your soundbar at

www.philips.com/support.

• Power cord quantity and plug type
vary by regions.

• Images, illustrations and drawings
shown on this User Manual are for
reference only, actual product may
vary in appearance.

Soundbar

What’s in the box

Check and identify the items in the

package:

• Soundbar x 1

• Remote control x 1

(AAA batteries x 2)

• Wireless subwoofer x 1

• Wall mount kit x 1

(Brackets x2 / Bracket screws x2 /
Wall mounting screws x2 / Wall anchors x2)

• Quick start guide / Warranty card /

Safety sheet x 1

• Wall mount template x 1

• Power cord* x 2

Soundbar

Wall mount kit

(brackets x2 / bracket screws x2 /

wall mounting screws x2 / wall anchors x2)

UL

Remote control

(AAA batteries x 2)

ation
form
n

ety I

Saf

2 X

2 X

2 X

Quick start guide

Warranty card/Safety sheet

TISI BS SAA

CCC

Wireless subwoofer

Headphones

Series

CTN

VDEVDE BS

Wall mount

template

This section includes an overview of the

soundbar.

1 2 3 4 5

6 87

1

- (Volume) button

Decrease the volume.

2

+ (Volume) button

Increase the volume.

3

(Play/Pause) button

Start, pause or resume play.

4

(Source)/Bluetooth pairing button

• Press to select an input source for

soundbar.

• In BT mode, press and hold for 3

seconds to disconnect from current

BT connected devices and enter the

Bluetooth pairing mode.

for Europe/UK for China

TAB8507/10 TAB8507/37 TAB8507/67 TAB8507/93 TAB8507/98

for US/Canada for Thailand

for Asia

7EN

5

(Standby-On) button

Power
state

On Follow source state

Semi
standby

Eco
standby

6

Power LED

Action Function

Press
the
button
once

Press
and
hold
seconds

• Wi-Fi is connected.

• It supports Play-

and Airplay2

Chromecast,

Spotify connect,

work with Alexa.

• Wi-Fi is o.

• The product enters

3

the lower power

consumption mode.

• Restarting the
system will take a
relatively longer
time.

• Turns white when in Eco standby

(network disconnected).

7

Remote control sensor /

Display panel

8

Wi-Fi LED

Wi-Fi LED indicator (Orange)

LED State Status

Blink

Double blink

Constant on

8 EN

Wi-Fi Access Point (AP)
mode

Wi-Fi Protected Setup
(WPS) mode

Connected / Pairing
successful

Connectors

This section includes an overview of the

connectors available on your soundbar.

2

1 3 4 5 6

7

8

1

(Wi-Fi Setup) button

• Trigger Wi-Fi setup for Play-.

• Press and hold the button for 4

seconds to active the Wps mode.

• Press and hold the button for 8
seconds to active the AP mode.

2

HDMI out (eARC) socket

The port supports the eARC/ARC

HDMI feature, connect to the HDMI

(eARC) input on the TV.

3

HDMI in socket

Connect to an HDMI source device,

such as a DVD player, Blu-ray Disc™

player, or gaming console.

4

Audio in

Audio input from, for example, an
MP3 player (3.5mm jack).

5

USB

• Connect to a USB storage device for

audio media play.

• Upgrade software of this product.

6

Optical in socket

Connect to an optical audio output

on the TV or a digital device.

7

AC in socket

Connect to the power supply.

8

Wall bracket slot

Wireless subwoofer

Remote control

This section includes an overview of the

wireless subwoofer.

abc

1

AC~ socket

Connect to the power supply.

2

Pair button

Press and hold to enter the pairing
mode for the subwoofer.

3

Subwoofer indicator

Determine the status based on the
wireless subwoofer indicator.

LED state Status

Fast blink Subwoofer in pairing mode

Constant on Connected / Pairing successful

Slow blink Connection / Pairing failed

This section includes an overview of the

remote control.

1

(Standby-On) button

Power
state

On Follow source state
Semi

standby

Eco
standby

1

3

Action Function

Press
the
button
once

Press
and
hold
seconds

• Wi-Fi is connected.

• It supports Play-

and Airplay2
Chromecast,
Spotify connect,
work with Alexa.

• Wi-Fi is o.

• The product enters

3

the lower power
consumption mode.

• Restarting the
system will take a
relatively longer
time.

2

4

5

6

8

7

9

9EN

2

(Source)

• Press to select an input source for

soundbar.

• In BT mode, press and hold for 3

seconds to disconnect from current

BT connected devices and enter the

Bluetooth pairing mode.

3

(Dolby Atmos)

Select a height eect level for Dolby

Atmos.

4

(Mute)

Mute or restore volume.

5

Navigation buttons

/ (Left/Right)

• Skip to the previous or next track in

USB/BT mode.

• Navigate Left/Right in menu

structure.

/ (Up/Down)

• Navigate up/down in menu structure.

(Center)

• Start, pause or resume play in USB/

BT mode.

• Conrm a selection.

6

(MENU)

Enter setup menu.

7

(Exit)

• Exit menu.

• Press and hold the button for 10

seconds to reset the Wi-Fi module
of soundbar to factory settings.

8

+/- (System’s volume)

Increase / decrease the system’s
volume.

9

+/- (Subwoofer’s volume)

Increase / decrease the subwoofer’s
volume.

Prepare the remote control

• The provided remote control allows

the unit to be operated from a
distance.

• Even if the remote control is

operated within the eective range

19.7 feet (6m), remote control
operation may be impossible if there
are any obstacles between the unit
and the remote control.

• If the remote control is operated
near other products which generate
infrared rays, or if other remote
control devices using infra-red rays
are used near the unit, it may operate
incorrectly. Conversely, the other
products may operate incorrectly.

Replace the remote control battery

Slide to remove the battery compartment

cover, insert 2 AAA batteries (1.5V) with

correct polarity, then slide the battery
compartment cover back into position.

• Make sure the (+) and (–) ends of
the batteries match the (+) and
(–) ends indicated in the battery
compartment.

1

2

10 EN

3

Precautions concerning batteries

• Be sure to insert the batteries with

correct positive “” and negative
“” polarities.

• Use batteries of the same type.

Never use dierent types of batteries

together.

• Either rechargeable or non­rechargeable batteries can be used.
Refer to the precautions on their
labels.

• Be aware of your ngernails when

removing the battery cover and the
battery.

• Do not drop the remote control.

• Do not allow anything to impact the

remote control.

• Do not spill water or any liquid on
the remote control.

• Do not place the remote control on a
wet object.

• Do not place the remote control
under direct sunlight or near sources
of excessive heat.

• Remove the battery from the remote
control when not in use for a long
period of time, as corrosion or
battery leakage may occur and result
in physical injury, and/or property

damage, and/or re.

• Do not use any batteries other than

those specied.

• Do not mix new batteries with old
ones.

• Never recharge a battery unless it is
conrmed to be a rechargeable type.

Placement

Place the subwoofer at least 1 meter (3
feet) away from your soundbar, and 10
centimeters away from the wall.

For best results, place your subwoofer as
shown below.

11EN

Wall mount

>32mm/1.26"

Note

Improper wall mounting may result in accident,

•

injury or damage. If you have any query, contact
Consumer Care in your country.

• Before wall mounting, make sure the wall can

support the weight of your soundbar.

• Before wall mounting, you need not remove

the rubber feet at the bottom of the soundbar,

otherwise the rubber feet cannot be xed back.

• Depending on the type of wall mounting, make

sure that you use screws of a suitable length
and diameter.

• Please check whether the USB port on the back of

the soundbar is connected to a USB device. If it is
found that the connected USB device affects the
wall-mount, you need to use another USB device
of the appropriate size.

Screw length/diameter

3.5-4mm/0.14 -0.16"

4mm/

0.16"

Suggested wall mounting height

You are recommended to install the TV
rst before wall mounting the soundbar.
With a TV preinstalled, wall mount the

soundbar 50mm/2.0’’ in distance from

the bottom of the TV.

WARNING!

To prevent injury, this apparatus must be securely

•

attached to the oor/wall in accordance with the

installation instructions.

• Suggested wall mounting height: ≤ 1.5 meters.

1

~50mm/2.0"

628mm / 24.7”

3.5-4mm/0.14 -0.16"

2

4mm/

0.16"

>32mm/1.26"

3

4

1 Drill 2 parallel holes (Diameter 3-8mm

each according to wall type) on the
wall.

» The distance between the holes

are: 628 mm / 24.7”

» You can use the wall mount

template provided for helping the
drilling holes position on the wall.

2 Secure the dowels and screws in the

holes.
» Be sure to leave a 3.5-4mm gap

between the wall and the screw’s
head.

3 Attach the wall brackets (x2) into the

back of the unit.

4 Hang the soundbar on the fastening

screws.

12 EN

3 Connect

HDMI in

HDMI out

Blu-ray Player/DVD Player

/Recorder/Set-top Box...

TV

HDMI out

(eARC/ARC)

HDMI in

This section helps you connect your
soundbar to a TV and other devices, and

then set it up.

Note

•

For identication and supply ratings, see the

type plate at the back or bottom of the product.

• Before you make or change any connections,

make sure that all devices are disconnected
from the power outlet.

Dolby Atmos®

Dolby Atmos gives you immersive listening
experience by delivering sound in three
dimensional space, and all the richness,
clarity, and power of Dolby sound.

For more information, please visit
dolby.com/technologies/dolby-atmos.

Use Dolby Atmos®

Dolby Atmos® is available in HDMI mode.
For the details of the connection, please
refer to “HDMI Connection”.

1 To use Dolby Atmos® in HDMI in/

HDMI eARC/ARC mode, your TV has

to support Dolby Atmos®

2 Make sure that “No Encoding” is

selected for bitstream in the digital
audio output of the connected

external device (e.g. Blu-ray DVD
player, TV etc.).

3 While entering Dolby Atmos / Dolby

Digital / PCM format, the soundbar

will show DOLBY ATMOS / DOLBY

AUDIO / PCM.

Note

•

The full Dolby Atmos experience is only

available when the soundbar is connected to
the source via a HDMI 2.0 cable.

• The soundbar will still function when connected

via other methods (such as a Digital Optical
cable) but they are unable to support all of the

Dolby features. Given this, our recommendation

is to connect via HDMI, in order to ensure full
Dolby support.

Connect to HDMI socket

Some 4K HDR TVs require the HDMI

input or picture settings to be set for
HDR content reception. For further setup
details on HDR display, please refer to the

instruction manual of your TV.

Option 1:

HDMI eARC (Enhance Audio Return
Channel)

Your soundbar supports HDMI with
eARC/ARC (Enhance Audio Return

Channel). If your TV is HDMI eARC/ARC
compliant, you can hear the TV audio

through your soundbar by using a single
HDMI cable.

.

HDMI out

(eARC/ARC)

TV

HDMI (eARC/ARC)

1 On your TV, turn on HDMI-CEC

operations. For details, see the TV

user manual.

• The HDMI ARC connector on the
TV might be labeled dierently. For
details, see the TV user manual.

13EN

2 Using a High Speed HDMI cable,

HDMI in

HDMI out

Blu-ray Player/DVD Player

/Recorder/Set-top Box...

TV

HDMI out

(eARC/ARC)

HDMI in

HDMI in

HDMI out

Blu-ray Player/DVD Player

/Recorder/Set-top Box...

TV

HDMI out

(eARC/ARC)

HDMI in

HDMI (eARC/ARC)

HDMI out

(eARC/ARC)

TV

HDMI in

HDMI out

Blu-ray Player/DVD Player

/Recorder/Set-top Box...

TV

HDMI out

(eARC/ARC)

HDMI in

HDMI (eARC/ARC)

HDMI out

(eARC/ARC)

TV

Optical out

Optical

TV

Headphone

(3.5mm)

Audio out

Audio in

TV

HDMI in

HDMI out

Blu-ray Player/DVD Player

/Recorder/Set-top Box...

TV

HDMI out

(eARC/ARC)

HDMI in

HDMI (eARC/ARC)

HDMI out

(eARC/ARC)

TV

Optical out

Optical

TV

connect the HDMI out (eARC/ARC)
connector on your soundbar to the

HDMI ARC connector on the TV.

Note

•

Your TV must support the HDMI-CEC and ARC

function. HDMI-CEC and ARC must be set to On.

• The setting method of HDMI-CEC and ARC may

dier depending on the TV. For details about
ARC function, please refer to your TV user

manual.

• Make sure to use the HDMI cables can support

the ARC function.

Option 2: Standard HDMI

If your TV is not HDMI ARC-compliant,
connect your soundbar to the TV

through a standard HDMI connection.

1 Use an HDMI cable to connect

the soundbar’s HDMI in socket to
your external devices (e.g. games

consoles, DVD players and Blu-ray).

2 Use an HDMI cable to connect the

soundbar’s HDMI out (eARC) socket
to the TV’s HDMI in socket.

Connect to Optical socket

1 Using an optical cable, connect the

Optical connector on your soundbar
to the Optical out connector on the

TV or other device.

Optical

TV

Optical out

• The digital optical connector might

be labeled Spdif or Spdif out.

Connect to Audio in
socket

• Use a 3.5mm to 3.5mm audio cable to

connect the TV’s headphone socket to

the Audio in socket on the soundbar.

Audio in

Headphone

(3.5mm)

Audio out

• Use a RCA to 3.5mm audio cable

to connect the TV’s audio output

sockets to the Audio in socket on the
soundbar.

Audio in

Audio out

TV

L

TV

R

14 EN

Connect to power

» Determine the status based on

the wireless subwoofer indicator.

• Before connecting the AC power
cord, ensure you have completed all
other connections.

• Risk of product damage! Ensure that
the power supply voltage corresponds
to the voltage printed on the back or
the underside of the unit.

1 Connect the mains cable to the AC~

socket of the unit and then into a
mains socket.

2 Connect the mains cable to the AC~

socket of the subwoofer and then
into a mains socket.

AC~

* Power cord quantity and plug type

vary by regions.

Pair up with the subwoofer

Automatic pairing

Plug the soundbar and the subwoofer
into the mains sockets and then press on
the unit or remote control to switch the
unit to ON mode. The subwoofer and
soundbar will automatically pair.

LED state Status

Fast blink Subwoofer in pairing mode

Constant on Connected / Pairing successful

Slow blink Connection / Pairing failed

Tips

Do not press Pair button on the rear of the

•

subwoofer, except for manual pairing.

Manual pairing

If no audio from the wireless subwoofer
can be heard, manually pair up the
subwoofer.

1 Unplug both the unit and the

subwoofer from the mains sockets
again, then plug them in again after 3
minutes.

2 Press and hold the Pair button on the

rear of the subwoofer for 5 seconds.

» The indicator on the subwoofer

will rapidly blink.

3 Then press button on the unit or

remote control to switch the unit ON.

» The indicator on the subwoofer

will become solid when
successful.

4 If the indicator still keeps blinking,

repeat step 1-3.

Tips

The subwoofer should be within 6 m of the

•

soundbar in an open area (the closer the
better).

• Remove any objects between the subwoofer

and the soundbar.

• If the wireless connection fails again, check if

there is a conict or strong interference (e. g.

interference from an electronic device) around

the location. Remove these conicts or strong

interferences and repeat the above procedures.

15EN

Connect to Wi-Fi

Fast blink Slow pulse

>8 seconds

Settings

Setup Play-Fi Device

SETUP

PlayFiDevice 1234

Your Home Router

Philips Sound Settings

Setup Play-Fi Device

SETUP

Your Home Router

Philips Sound Settings

Setup Play-Fi Device

SETUP

Settings

Setup Play-Fi Device

SETUP

Return to this app to continue setup.

Ready?

Go To Wi-Fi Settings

PlayFiDevice 1234

Your Home Router

Select NameXSelect Nam

e

Your Play-Fi device is connecting to

Your Home Router

When the Wi-Fi light on the device stops
blinking and becomes solid the device is

setup and ready to be used.

Philips Sound Settings

Setup Play-Fi Device

SETUP

Bedroom

(Wireless operation)

(For iOS and Android version)

By connecting this unit and mobile
phones, tablets (such as iPad, iPhone,
iPod touch, Android phones, etc.) to the
same Wi-Fi network, you can then use

the Philips Sound app powered by DTS
Play- to control the soundbar to listen
to audio les.

1 Download and install the Philips

Sound app powered by DTS Play- on

a phone or tablet.

Philips Sound

• Make sure your router is turned on
and working properly.

Note

•

Depending on the device version, the operation
screen and the way to perform operations may
vary.

2 Connect your phone or tablet to the

same Wi-Fi network that you want to
connect your soundbar.

Wi-Fi

<

Wi-Fi

seconds to trigger the Wi-Fi
connection

» Until the speaker make a second

tone and then release the button

Two tone

4 Wait until the Wi-Fi light indicator on

the front cabinet goes from a fast blink
to a slow pulse. When it begins pulsing
slowly, it indicates that the speaker is
entering the Wi-Fi setup mode.

Fast blink Slow pulse

5 Launch the Philips Sound app

powered by DTS Play-. Follow the

instructions in the app to connect
this product to your Wi-Fi network.

Philips Sound

Return to this app to continue setup.

Ready?

Go To Wi-Fi Settings

Settings

SETUP

Setup Play-Fi Device

PlayFiDevice 1234

3 Press and hold (Wi-Fi) button

located at the back cabinet for 8

16 EN

Your Home Router

Wi-Fi Password

1234567890I

Enter the password for the network Your Home Router

Show Password.

X

PlayFiDevice 1234

Your Home Router

Select NameXSelect Nam

e

Your Play-Fi device is connecting to

Philips Sound

Settings

Setup Play-Fi Device

SETUP

Bedroom

Your Home Router

e

X

Setup Play-Fi Device

SETUP

Settings

Settings

Your Home Router

When the Wi-Fi light on the device stops

blinking and becomes solid the device is

setup and ready to be used.

Select NameXSelect Nam

Bedroom

6 After successful Wi-Fi connection, the

Wi-Fi light indicator will stop pulsing
and turn solid. Once you set up this
product on your Wi-Fi network, you
can control it from any smartphone or
tablet on the same network.

7 After connection, you can change

the device name. There are several

names to choose from or create your

own by choosing Custom Name at

the end of the name list. Otherwise,
it follows the default name.

8 After connection, this product may

perform a software update.
Upgrade to the latest software

when it is your rst time set up.
The software upgrade may take

several minutes. Do not unplug your

speaker, turn o your device, or leave

the network during the update.

Note

•

After connection, the product may perform
a software update. Upgrade is required after
initial set up. Without the upgrade, not all
product features can be available.

• When the rst time set up is not successful, hold

down the
for 8 seconds until the second tone can be
heard and the Wi-Fi light is changed to a slow
pulse. Reset the Wi-Fi connection, restart the
app and start the set up again.

• If you want to change from one network to

another, you need to set up the connection
again. Press hold down the
on the soundbar for 8 seconds to reset the Wi-Fi
connection.

• When the rst time set up is not successful,

please close the Philips Sound app powered by

DTS Play-. Restart the app and try the setup

again.

(Wi-Fi) button on the soundbar

(Wi-Fi) button

AirPlay setup

Use AirPlay to set up the Wi-Fi connection
of iOS device (iOS7 or later) and soundbar.

1 iOS device: Settings > Wi-Fi > select

home network【Play- device
(xxxxxx)】

» Go to the Wi-Fi set up. The Play-Fi

device name displays around in 5
seconds.

» Select the Play-Fi device in the

Airplay set up.

» Press “Done” when set up

complete

» After successful Wi-Fi connection,

the Wi-Fi light indicator will stop
pulsing and turn solid.

Solid

2 Return to Philips Sound App to name

the device.

17EN

3 After connection, you can change

the device name. There are several

names to choose from or create your

own by choosing Custom Name at

the end of the name list. Otherwise,
it follows the default name.

WPS mode

If your router has Wi-Fi Protected Setup
(WPS), you can set up the connection
without entering a password.

Connect the soundbar to

Philips Play- enabled TV

1 Power up your DTS Play- TV

connected to the internet.

» TV sound is muted.

2 Enter the Settings menu on TV.

» Settings > Sound > DTS Play-

Surround sound Setup

Follow the on-screen setup.

1

1 Press and hold

the

(Wi-Fi)

button for 4

WPS

seconds. You
will hear a tone
and the Wi-Fi
light will begin double blink.

2 Press the WPS button on your router.

The button is normally marked with

this WPS logo.

3 After successful Wi-Fi connection,

the Wi-Fi light indicator will stop
pulsing and turn solid.

Note

•

WPS is not a standard feature on all routers.
If your router does not have WPS then use
Standard Wi-Fi Setup.

• Press the (Wi-Fi) button once if you want to

exit the WPS mode or it will automatically exit
after 2 minutes.

18 EN

Front Speakers

One

2

Two

The home theater speakers are now

independent speakers.

3

TV Audio Setup

You can also stream the TV’s audio

to your home speakers wirelessly.
Follow the on-screen setup.

DTS Play-Fi TV Audio

Stream this TV's audio to wireless speakes
throughout your home.

Learn more about DTS Play-Fi enabled

speakers at play-�.com

Connect Speakers

1

DTS Play-Fi TV Audio

Play-Fi Speaker

Connect Speakers

Select Speakers

Volume

B8507

2

4 Use your

soundbar

This section helps you use the soundbar

to play audio from connected devices.

Before you start

• Make the necessary connections

described in the quick start guide
and the user manual.

• Switch the soundbar to the correct
source for other devices.

Turn ON and OFF

3TAFB1

• When you rst connect the unit to

the main socket, the unit will be

in STANDBY mode. The STANDBY

indicator will light up.

Power
state

Action Function

On Follow source state
Semi

standby

Press
the
button
once

• Wi-Fi is
connected.

• It supports Play-

and Airplay2
Chromecast,
Spotify connect,
work with Alexa.

Eco
standby

Press
and
hold
seconds

• Wi-Fi is o.

• The product enters

3

the lower power
consumption
mode.

• Restarting the
system will take a
relatively longer
time.

19EN

Select modes

Press the button repeatedly on the
unit or on the remote control to select the

Optical, Audio in, USB, BT(Bluetooth),
HDMI in, HDMI eARC/ARC mode.

» The selected mode will show on

the display.

Display Status

OPT
AUX
U5B

BT

E-ARC
ARC

Optical

Audio in

USB

Bluetooth

HDMI IN

HDMI eARC
HDMI ARC

Enjoy Dolby Atmos
sound

Press button to select a height

surround eects level to best suit

your personal taste according to your
environment.

• UPMIX: Make sure that all
speakers are utilized for contents
less than 5.1.2 or 7.1.2 speaker

conguration.

• STANDARD: Original sound.

• AI: The media intelligence

function of Dolby Atmos for
home audio is utilized to drive
the vocal enhancement or

surround eects.

» By default, the audio upmix is set

to 7.1.2.

Tips

•

Play- is not an optional source. Play- needs to

be directly controlled by APP.

Adjust the volume

Adjust the system’s volume

Press the +/- buttons on the soundbar
or press
remote control to increase or decrease
the system’s volume level.

Adjust the subwoofer’s volume

Press +/- (subwoofer) buttons on the
remote control to increase or decrease
the subwoofer’s volume level.

20 EN

+/- (Volume) buttons on the

• To mute sound, press

(Mute)

button on the remote control.

• To restore the sound, press

(Mute) again or press

+/-

(Volume).

Tips

Display shall show the speaker channels

•

according with dierent speaker congurations,
such as:

7.1.2: soundbar

7.1.4: soundbar + surround speakers

7.1.4: soundbar + surround speakers+ subwoofer

7.2.2: soundbar + 2 x subwoofer

7.2.4: soundbar + surround speakers + 2x subwoofer

Setup menu

The unit allows you to congure

advanced settings to provide you with an
even better experience.

Button Function

Enter settings menu

/

/

Last/next sub menu

Previous/next selection

Exit setting menu

Display Description

EQ

XX

TRE xx

BT PAIR

FL XX

FR XX

CT XX

DRC

YNC

DI5P

5TNBY

UPGRADE

Select equalizer (EQ) eect

Adjust the bass level

Adjust the treble level

Start Bluetooth pairing

Front Left Speaker

Front Right Speaker

Center Speaker

Dynamic range control

Set the Audio Delay

Set display brightness

Display o setting

Auto-standby ON/OFF

Update rmware via USB

EQ

Select predened sound modes to suit
your video and music: MOVIE, MUSIC,

VOICE, STADIUM, CUSTOM.

• MOVIE: Create a surround listening
experience. Ideal for watching
movies.

• MUSIC: Create two-channel or

multi-channel stereo sound. Ideal for
listening to music.

• VOICE: Create sound eect which

makes human voice more clear and
outstanding for listening.

• STADIUM: Create an atmosphere

as if watching a sports game in a
stadium.

• CUSTOM: Customize the sound
based on your preferences. Need to
be set via the Fine Tune App.

• By default, the EQ is set to MOVIE.

Bass/Treble

Change the low frequency (bass) and
high frequency (treble) settings of this
product.

• BAS -5 ~ BAS +5

• TRE -5 ~ TRE +5

» By default, the Bass/Treble is set

to 0.

BT PAIR

Enter the Bluetooth pairing mode.

• If you want to connect your
soundbar with another Bluetooth
device, you can activation the pairing
in the menu (BT PAIR) to disconnect
all devices and enter the Bluetooth
pairing mode.

» Press

press

> select “BT PAIR” > Then

(Enter) to conrm the

Bluetooth pairing mode.

• Follow step 2-3 in “Play from
Bluetooth devices“ above to pair

your Bluetooth device.

Tips

•

The “BT PAIR” menu will only be displayed
when the current signal source is in “BT” mode

Adjust speaker level

• Front Left: FL -5 ~ FL +5

• Front Right : FR -5 ~ FR +5

• Center: CT -5 ~ CT +5

» By default, the speaker level is set

to 00.

21EN

Dynamic range control (DRC)

You can apply dynamic range control to
Dolby Digital tracks.

• ON : Optimize the dynamic range

• OFF : Turn o dynamic range

adjustment

» AUTO : Dynamic range is

automatically adjusted

» By default, the DRC mode is set

to AUTO.

Auto Standby

The unit automatically turns to Standby
mode after about 15 minutes if the TV or
the external unit is disconnected (or USB, BT
function bit playback pause), switched o.

• STNBY IN 15M: Turn on the

Auto-Standby.

• STNBY OFF: Turn o the Auto-

Standby.

» By default, the key tone is set to

ON.

Note

•

DRC is not available in USB/BT/Play- mode.

AV SYNC

Set the Audio Delay.

Video image processing, sometimes

longer than the time required to process

the audio signal. This is called “delayed.”

Audio Delay feature is designed to
remedy this delay.

• S 00 ~ S 200
» By default, the audio delay is set

to 00.

DIM

Set display brightness.

• HIGH, MID, LOW

» By default, the dimmer is set to

MID.

DISPLAY

Set to turn o the display automatically

(except the Wi-Fi LED indicator) after 10
seconds of idle when no user operation.

• ON: Set to display on

• OFF: Set to display o

» By default, the display is set to

ON.

Note

•

To switch the unit o completely, remove the

mains plug from the mains socket.

• Please turn the unit o completely to save

energy when not in use.

Update rmware via USB

Check if there is the latest rmware

version on www.philips.com/support.

Search for your model and click on

“Software and drivers”.

Copy the software update les into USB

ash drive, insert USB ash drive on the

unit.

» Press

“PLAY TO START”

» Then press

conrm.

» Upgrade nished and restart.

> select “UPGRADE” >

(Enter) button to

22 EN

Play from Bluetooth
devices

Through Bluetooth, connect the

soundbar with your Bluetooth device
(such as an iPad, iPhone, iPod touch,
Android phone, or laptop), and then you

can listen to the audio les stored on the

device through your soundbar speakers.

1 Press the button repeatedly on the

unit or on the remote control to switch
the soundbar to Bluetooth mode.

» BT is displayed on the display

panel.

2 On the Bluetooth device, switch

on Bluetooth, search for and select
“Philips B8507” to start connection
(see the user manual of the Bluetooth
device on how to enable Bluetooth).

3 Wait until you hear the voice prompt

from the soundbar.
» If successfully connected, BT is

displayed on the display panel.

4 Select and play audio les or music

on your Bluetooth device.

• During play, if a call comes in,

music play pauses. Play resumes
when the call ends.

• If your Bluetooth device supports

AVRCP prole, on the remote

control you can press
to a track, or press
resume play.

To disconnect and pair a new
Bluetooth device

/ to skip

to pause/

disconnect all devices and enter the
Bluetooth pairing mode.

» The display will ashing “PAIR“.

2 Follow step 2-3 in “Play from

Bluetooth devices“ above to pair

your Bluetooth device.

Note

•

In an open space without obstructions.

The maximum operational range between

the soundbar and a Bluetooth device is
approximately 10 meters (33 feet).

• Compatibility with all Bluetooth devices is not

guaranteed.

• The music streaming may be interrupted by

obstacles between the device and soundbar,
such as wall, metallic casing that covers the
device, or other devices nearby that operate in
the same frequency.

Multi-point control

The product support multi-point feature,

and can connect two Bluetooth devices
at same time (such as an iPad, iPhone,
iPod touch, Android phone, or laptop).

• There is audio prompt when the

second Bluetooth device connect the
soundbar.

• When the second Bluetooth device
stream its audio to soundbar, the

rst Bluetooth device will pause the

playback.

• Incoming call has priority over music

playback regardless from rst or

second devices.

1 In Bluetooth mode, Press > select

“BT PAIR” > Then press
disconnect all devices and enter the
Bluetooth pairing mode.

• Alternatively directly press and
hold

button on the soundbar to

(Enter) to

Listen to an external
device

Ensure that the unit is connected to the

TV or audio device.

23EN

1 Press the button repeatedly on the

unit or on the remote control to select
the Optical,

Audio in, HDMI in, HDMI

ARC mode.

2 Operate your audio device directly

for playback features.

3 Press the VOL +/– buttons to adjust

the volume to your desired level.

» When selecting a dierent audio

format, the soundbar will display

the following as follows:

Audio (abbreviation) Display

LPCM 2ch PCM
LPCM 5.1ch PCM
LPCM 7.1ch PCM
Dolby Digital Dolby AUDIO
Dolby TrueHD Dolby AUDIO
Dolby Digital Plus Dolby AUDIO
Dolby Atmos -

Dolby TrueHD

Dolby Atmos ­Dolby Digital Plus

Note

•

The unit may not be able to decode all digital

audio formats from the input source. In this case,

the unit will mute. This is NOT a defect. Ensure

that the audio setting of the input source (e.g.
TV, game console, DVD player, etc.) is set to PCM
or Dolby Digital (Refer to the user manual of the
input source device for its audio setting details)
with HDMI in / HDMI ARC / Optical input.

Dolby Atmos

Dolby Atmos

2 Press the button repeatedly on

the unit or on the remote control to
select the USB mode.

3 During playback:

Button Action

Start, pause or resume play.

Skip to the previous or next track.

/

Tips

•

The unit may not be compatible with certain

types of USB storage devices.

• If you use a USB extension cable, USB hub,

or USB multifunctional card reader, the USB
storage device may not be recognized.

• Do not remove the USB storage device during

le reading.

• The unit can support USB devices with up to 32

GB of memory.

• This unit can play MP3 / WAV / FLAC.

• Support a USB port: 5V 500mA.

Factory reset

Play audio through USB

Enjoy audio on a USB storage device,

such as an MP3 player and USB ash

memory, etc.

1 Insert the USB device.

24 EN

Reset device to default setting.

• Turn on the soundbar, press and hold

the +/- buttons at the same time for
8 seconds.

» Display shows “RESET” for 5

seconds.

» While system reboots, display

shows “REBOOT”.

5 Product

specifications

Note

Specications and design are subject

•

to change without notice.

Bluetooth / Wireless

Bluetooth proles A2DP, AVRCP

Bluetooth version V 5.3
Bluetooth frequency

band

Transmitter power ≤ 10dBm

5.8G Wireless frequency
range / Transmitter

power (EIRP)

Network supported

WiFi IEEE 802.11a/b/g/n/ac Wireless
frequency band (Wi-Fi) /Radio frequency
power transmitted (EIRP)

2.4G Wi-Fi 2400 ~ 2483.5 MHz / ≤ 20dBm
5150 ~ 5350 MHz / ≤ 20dBm

5G Wi-Fi

5470 ~ 5725 MHz / ≤ 27dBm
5725 ~ 5850 MHz / ≤ 14dBm

Soundbar

Power supply

RMS output power
MAX output power

Power consumption 35 W
Standby power

consumption
Frequency response 150Hz - 20KHz
Speakers impedance 8Ω
Dimension (W x H x D )
Weight 2.7 kg
Operating

temperature

2402 ~ 2480MHz

5729~5850 MHz

≤ 10dBm

100-240V~

50/60Hz
180W

360W (10% THD )

< 0.5 W

940 x 65 x 106 mm

0°C - 45°C

Subwoofer

Power supply

RMS output power
MAX output power

Power consumption 25 W
Standby power

consumption
Frequency response 35Hz - 150Hz
Impedance 3 Ω

Dimension (W x H x D ) 150 x 410 x 309 mm

Weight 5.6 kg
Operating

Temperature

100-240V~

50/60Hz
120W

240W (10% THD )

< 0.5 W

0°C - 45°C

USB

USB direct version 2.0 Full Speed

USB

Extension Codec Sample Rate Bitrate

MPEG 1

Layer 1

MPEG 1

Layer 2

MPEG 1

Layer 3

.mp3

.wav

.ac

MPEG 2 /
MPEG 2.5

Layer 1

MPEG 2 /
MPEG 2.5

Layer 2

MPEG 2/
MPEG 2.5

Layer 3

WAV 16 ~ 48 kHz

FLAC

5V

500mA

16 ~ 48 kHz 32 ~ 448 kbps

16 ~ 48 kHz 8 ~ 384 kbps

16 ~ 48 kHz 8 ~ 320 kbps

16 ~ 48 kHz 8 ~ 256 kbps

16 ~ 48 kHz 8 ~160 kbps

16 ~ 48 kHz 8 ~ 160 kbps

Up to 1536
kbps

Up to 48 kHz /
16 bit

Remote control

Distance/Angle 6m/30°

Battery type AAA (1.5V X 2)

25EN

Supported audio formats

Format Function

HDMI Input HDMI eARC HDMI ARC OPTICAL

LPCM 2ch √ √ √ √

LPCM 5.1ch √ √ √ √

LPCM 7.1ch √ √ -- --

Dolby Digital √ √ √ √

Dolby Digital Plus √ √ √ --

Dolby TrueHD √ √ -- --

Dolby MAT √ √ -- --

Dolby Atmos ­Dolby Digital Plus

Dolby Atmos -

Dolby TrueHD

Dolby Atmos -

Dolby MAT

√ : Supported format.

-- : Unsupported format.

√ √ √ --

√ √ -- --

√ √ -- --

The product shall comply with Dolby indication mandatory requirements
marked below

Input
Signal

Dolby
Digital

Dolby
Digital Plus

Dolby

TrueHD

Dolby MAT

26 EN

Audio format

Channel-based

Object-based - √

Channel-based

Object-based - √

Channel-based

Object-based - √

Channel-based

Dolby
Virtualizer

O √

On √

O √

On √

O √

On √

O √

On √

Dolby Atmos1Dolby Surround1Dolby Audio

Format Indication

6 Troubleshooting

Warning

Risk of electric shock. Never remove the

•

casing of the product.

To keep the warranty valid, never try to

repair the product yourself.
If you have problems using this product,

check the following points before you
request service. If you still have a problem,
get support at www.philips.com/support.

Main unit

The buttons on the main unit do not
work.

• Disconnect form the power supply for
a few minutes, and then connect again.

No power

• Ensure that the AC cord is properly
connected.

• Ensure that there is power at the AC
outlet.

• Press the
control or soundbar to turn the
soundbar on.

Sound

No sound from the soundbar speaker.

• Connect the audio cable from your

soundbar to your TV or other devices.

However, you do not need a separate

audio connection when:

- the soundbar and TV are connected

through HDMl ARC connection, or

- a device is connected to the HDMI in

connector on your soundbar.

• On the remote control, select the
correct audio input.

• Make sure that the soundbar is not
muted.

• Reset this product to its factory
settings (see “Factory reset”).

button on the remote

Distorted sound or echo.

• If you play audio from TV through
this product, make sure that the TV

is muted.

Audio and video are not synchronized.

• Press to synchronize the audio with
the video.

No sound from the wireless subwoofer.

• Manually connect the subwoofer to
the main unit.

• Increase the volume. Press the

(Volume) on the remote control or

on the soundbar.

• When using either of the Digital

input, if there is no audio:

- Try setting the TV output to PCM or

- Connect directly to your Blu-ray/

other sources. Some TVs do not

pass through digital audio.

• Your TV may be set to variable audio
output. Conrm that the audio

output setting is set to FIXED or

STANDARD, not VARIABLE. Refer
to your TV’s user manual for more

detailed information.

• If using Bluetooth, ensure that the
volume on your source device is
turned up and that the device is not
muted.

• When the playback freezes and
there is no sound in Wi-Fi mode,
please check whether your home
network is normal.

+/-

Bluetooth

A device cannot connect with the
soundbar.

• The device does not support the
compatible proles required for the

soundbar.

• You have not enabled the Bluetooth
function of the device. See the user
manual of the device on how to
enable the function.

27EN

• The device is not correctly connected.

Connect the device correctly.

• The soundbar is already connected

with another Bluetooth device.
Disconnect the connected device,
and then try again.

Quality of audio play from a connected
Bluetooth device is poor.

• The Bluetooth reception is poor.

Move the device closer to the
soundbar, or remove any obstacle
between the device and the
soundbar.

I can’t nd the Bluetooth name of this

unit on my Bluetooth device.

• Ensure the Bluetooth function is
activated on your Bluetooth device.

• Re-pair the unit with your Bluetooth
device.

Wi-Fi

Wi-Fi Connection cannot be established.

• Check the availability of WLAN

network on the router.

• Place the Wi-Fi router closer to the
unit.

• Make sure the password is correct.

• Check the WLAN function or reboot

the modem and Wi-Fi router.

Dolby Atmos

Cannot achieve outstanding Dolby

Atmos eects.

• For non-HDMI connections (such
as use of USB, Bluetooth, Optical or

AUDIO IN), limited height surround
eects are generated. See the

section of ‘Dolby Atmos’ about how

to achieve best Dolby Atmos eects.

Play-

Cannot discover the Play- supported

devices from the app.

28 EN

• Make sure the device is connected to
the Wi-Fi.

Cannot play Play- music.

• Certain network service or contents
available through the device may
not be accessible in case the service
provider terminates its service.

• When the rst time set up is not

successful, close the Philips Sound

app powered by DTS Play-. Restart

the app.

• When the speaker was set as Stereo
Pairs or Surround Sound, the speaker
need to be disconnected in the App
before use separately.

Remote control does not wor

• Before you press any playback

control button, rst select the correct

source.

• Reduce the distance between the
remote control and the unit.

• Insert the battery with its polarities
(+/-) aligned as indicated.

• Replace the battery.

• Aim the remote control directly at

the sensor on the front of the unit.

This is a 15 mins power o function,

one of the ERPII standard requirement
for saving power

• When the unit’s external input
signal level is too low, the unit will

be turned o automatically in 15

minutes. Please increase the volume
level of your external device.

The subwoofer is idle or the indicator of
subwoofer do not light up

• Please unplug power cord from
the mains socket, and plug it in
again after 3 minutes to reset the
subwoofer.

k

Trademarks:

For DTS patents, see http://patents.dts.com.
Manufactured under license from DTS, Inc. (for

companies headquartered in the U.S./Japan/

Taiwan) or under license from DTS Licensing
Limited (for all other companies). DTS, DTS Play-Fi,
Play-Fi and the DTS Play-Fi and Play-Fi logos are
registered trademarks or trademarks of DTS, Inc.

in the United States and other countries. © 2021

DTS, Inc. ALL RIGHTS RESERVED.

The Wi-Fi CERTIFIED™ Logo is a registered

trademark of Wi-Fi Alliance®.

The Adopted Trademarks HDMI, HDMI High­Denition Multimedia Interface, HDMI trade

dress and the HDMI Logos are trademarks
or registered trademarks of HDMI Licensing
Administrator, Inc. in the United States and
other countries.

Dolby, Dolby Vision, Dolby Atmos, and the

double-D symbol are registered trademarks
of Dolby Laboratories Licensing Corporation.
Manufactured under license from Dolby

Laboratories. Condential unpublished

works. Copyright © 2012-2021 Dolby
Laboratories. All rights reserved.

Google, Google Play and Chromecast built-in are
trademark of Google LLC. Google Assistant is not

available in certain languages and countries.

To control this AirPlay 2 -enabled speaker, iOS

11. 4 or later is required. Use of the Works with
Apple badge means that an accessory has been

designed to work specically with technology
identied in the badge and has been certied by

trademarks of Apply Inc. ,registered in the U. S.
and other countries.

Apple® and AirPlay® are trademarks of Apple Inc.,
registered in the U.S. and other countries.

The Spotify Software is subject to third party
licenses found here: www.spotify.com/connect/

third-party-licenses

The Bluetooth® word mark and logos are

registered trademarks owned by Bluetooth

SIG, Inc. and any use of such marks by MMD
Hong Kong Holding Limited is under license.

Other trademarks and trade names are those
of their respective owners.

Roku, the Roku logo, Roku TV, Roku TV
Ready, and the Roku TV Ready logo are

trademarks and/or registered trademarks of

Roku, Inc. This product is Roku TV Ready-

supported in the United States, Canada,

United Kingdom, Mexico and Brazil.

Countries are subject to change. For the
most current list of countries in which this

product is Roku TV Ready-supported, please

[email protected].

Specications are subject to change without notice. Please visit
www.Philips.com/support for the latest updates and documents.

Philips and the Philips Shield Emblem are registered trademarks of

Koninklijke Philips N.V. and are used under license.

This product has been manufactured by and is sold under the responsibility
of MMD Hong Kong Holding Limited or one of its aliates, and MMD
Hong Kong Holding Limited is the warrantor in relation to this product.

TAB8507RE_UM_EN_V1.0_20220722