Philips NE5532AD8, NE5532AN, NE5532D, NE5532D8, NE5532N installation Guide
...
INTEGRATED CIRCUITS
NE/SA/SE5532/5532A
Internally-compensated dual low noise
operational amplifier
Product data
Supersedes data of 1997 Sep 29
2001 Aug 03
Philips Semiconductors Product data
Internally-compensated dual low noise
operational amplifier
DESCRIPTION
The 5532 is a dual high-performance low noise operational amplifier.
Compared to most of the standard operational amplifiers, such as
the 1458, it shows better noise performance, improved output drive
capability and considerably higher small-signal and power
bandwidths.
This makes the device especially suitable for application in
high-quality and professional audio equipment, instrumentation and
control circuits, and telephone channel amplifiers. The op amp is
internally compensated for gains equal to one. If very low noise is of
prime importance, it is recommended that the 5532A version be
used because it has guaranteed noise voltage specifications.
FEA TURES
•Small-signal bandwidth: 10 MHz
•Output drive capability: 600 Ω, 10 V
•Input noise voltage: 5 nV/√Hz (typical)
•DC voltage gain: 50000
•AC voltage gain: 2200 at 10 kHz
•Power bandwidth: 140 kHz
•Slew rate: 9 V/µs
•Large supply voltage range: ±3 to ±20 V
•Compensated for unity gain
RMS
NE/SA/SE5532/5532A
PIN CONFIGURATIONS
N, D8 Packages
OUTPUT A
INVERTING INPUT A
NON-INVERTING INPUT A
NOTE:
1. SOL and non-standard pinout.
1
2
3
V-
D Package
–IN
1
A
2
+IN
A
3
NC
4
–V
CC
5
NC
6
NC
7
+IN
B
8
–IN
B
Figure 1. Pin Configurations
A
B
TOP VIEW
TOP VIEW
8
V+
7
OUTPUT B
6
INVERTING INPUT B
54
NON-INVERTING INPUT B
1
NC
16
15
NC
NC
14
13
OUT
A
12
+V
CC
11
OUT
B
NC
10
9
NC
SL00332
ORDERING INFORMATION
DESCRIPTION TEMPERATURE RANGE ORDER CODE DWG #
8-Pin Small Outline Package (SO) 0 °C to 70 °C NE5532AD8 SOT96-1
8-Pin Plastic Dual In-Line Package (DIP) 0 °C to 70 °C NE5532AN SOT97-1
16-Pin Plastic Small Outline Large (SOL) Package 0 °C to 70 °C NE5532D SOT162-1
8-Pin Small Outline Package (SO) 0 °C to 70 °C NE5532D8 SOT96-1
8-Pin Plastic Dual In-Line Package (DIP) 0 °C to 70 °C NE5532N SOT97-1
8-Pin Plastic Dual In-Line Package (DIP) –40 °C to +85 °C SA5532N SOT97-1
8-Pin Small Outline Package (SO) –55 °C to +125 °C SE5532AD8 SOT96-1
16-Pin Plastic Dual In-Line Package (DIP) –55 °C to +125 °C SE5532N SOT38-4
2001 Aug 03 853-0949 26836
2
Philips Semiconductors Product data
Internally-compensated dual low noise
operational amplifier
EQUIVALENT SCHEMATIC (EACH AMPLIFIER)
+
_
NE/SA/SE5532/5532A
SL00333
Figure 2. Equivalent Schematic (Each Amplifier)
ABSOLUTE MAXIMUM RATINGS
SYMBOL PARAMETER RATING UNIT
V
S
V
IN
V
DIFF
T
amb
T
stg
T
j
P
D
T
sld
NOTES:
1. Diodes protect the inputs against over-voltage. Therefore, unless current-limiting resistors are used, large currents will flow if the differential
input voltage exceeds 0.6V . Maximum current should be limited to ±10 mA.
2. Thermal resistances of the above packages are as follows:
N package at 100 °C/W
D package at 105 °C/W
D8 package at 160 °C/W
Supply voltage ±22 V
Input voltage ±V
Differential input voltage
1
SUPPLY
±0.5 V
Operating temperature range
NE5532/A 0 to 70 °C
SA5532 –40 to +85 °C
SE5532/A –55 to +125 °C
Storage temperature –65 to +150 °C
Junction temperature 150 °C
Maximum power dissipation,
T
= 25 °C (still-air)
amb
2
8 D8 package 780 mW
8 N package 1200 mW
16 D package 1200 mW
Lead soldering temperature (10 sec max) 230 °C
V
2001 Aug 03
3
Philips Semiconductors Product data
SYMBOL
PARAMETER
TEST CONDITIONS
UNIT
A
VOL
Large-signal voltage gain
V
OUT
Out ut swing
V
SYMBOL
PARAMETER
TEST CONDITIONS
UNIT
Internally-compensated dual low noise
operational amplifier
DC ELECTRICAL CHARACTERISTICS
T
= 25 °C; VS = ±15 V , unless otherwise specified.
amb
V
OS
∆VOS/∆T 5 5 µV/°C
I
OS
∆IOS/∆T 200 200 pA/°C
I
B
∆IB/∆T 5 5 nA/°C
I
CC
V
CM
CMRR Common-mode rejection ratio 80 100 70 100 dB
PSRR Power supply rejection ratio 10 50 10 100 µV/V
R
IN
I
SC
NOTES:
1. Diodes protect the inputs against overvoltage. Therefore, unless current-limiting resistors are used, large currents will flow if the differential
input voltage exceeds 0.6 V . Maximum current should be limited to ±10 mA.
2. For operation at elevated temperature, derate packages based on the package thermal resistance.
3. Output may be shorted to ground at V
rating is not exceeded.
Offset voltage 0.5 2 0.5 4 mV
Offset current 100 10 150 nA
Input current 200 400 200 800 nA
Supply current
Common-mode input range ±12 ±13 ±12 ±13 V
-
p
Input resistance 30 300 30 300 kΩ
Output short circuit current 10 38 60 10 38 60 mA
= ±15 V, T
S
1, 2, 3
SE5532/A NE5532/A, SA5532
Min Typ Max Min Typ Max
Over temperature 3 5 mV
Over temperature 200 200 nA
Over temperature 700 1000 nA
Over temperature 13 mA
RL ≥ 2 kΩ; VO = ±10 V 50 100 25 100 V/mV
Over temperature 25 15 V/mV
RL ≥ 600 Ω; VO = ±10 V 40 50 15 50 V/mV
Over temperature 20 10 V/mV
RL ≥ 600 Ω ±12 ±13 ±12 ±13
Over temperature ±10 ±12 ±10 ±12
RL ≥ 600 Ω; VS = ±18 V ±15 ±16 ±15 ±16
Over temperature ±12 ±14 ±12 ±14
RL ≥ 2 kΩ ±13 ±13.5 ±13 ±13.5
Over temperature ±12 ±12.5 ±10 ±12.5
= 25 °C. Temperature and/or supply voltages must be limited to ensure dissipation
amb
NE/SA/SE5532/5532A
8 10.5 8 16 mA
AC ELECTRICAL CHARACTERISTICS
T
= 25 °C; VS = ±15 V , unless otherwise specified.
amb
R
OUT
A
V
GBW Gain bandwidth product CL = 100 pF; RL = 600 Ω 10 MHz
SR Slew rate 9 V/µs
2001 Aug 03
NE/SE5532/A, SA5532
Min Typ Max
Output resistance
AV = 30 dB Closed-loop
f = 10 kHz, R
= 600 Ω
L
0.3 Ω
Voltage-follower
Overshoot VIN = 100 mV
P-P
10 %
CL = 100 pF; RL = 600 Ω
Gain f = 10 kHz 2.2 V/mV
V
= ±10 V 140 kHz
Power bandwidth V
OUT
= ±14 V; RL = 600 Ω, 100 kHz
OUT
VCC=±18V
4
Loading...