1
2
3
4
5
6
11
12
13
14
10
9
8
7
empty page before TOC
English 6
Nederlands 31
Русский 58
简体中文
ﺔﻴﺑﺮﻌﻟﺍ
84
105
English
6
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benefit from the support that
Philips offers, register your product at
www.philips.com/welcome.
Please read this user manual, as it contains
information about the features of this shaver as
well as some tips to make shaving easier and more
enjoyable.
General description (Fig.1)
1 Protection cap for cleansing brush attachment
2 Click-on cleansing brush attachment
3 Click-on precision trimmer attachment
4 Click-on shaving unit
5 On/off button
6 Socket for small plug
7 Exclamation mark
8 Replacement reminder
9 Battery charge indicator
10 Travel lock symbol
11 Cleaning reminder
12 Supply unit
13 Small plug
14 Pouch
Important safety information
Read this important information carefully before
you use the appliance and its accessories and save
it for future reference. The accessories supplied
may vary for different products.
English
English
Danger
- Keep the supply unit dry.
Warning
- To charge the battery, only use the
detachable supply unit (type HQ8505)
provided with the appliance.
- The supply unit contains a transformer. Do
not cut off the supply unit to replace it with
another plug, as this causes a hazardous
situation.
- This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved. Children shall not play
with the appliance. Cleaning and user
maintenance shall not be made by children
without supervision.
7
English
8
- Always unplug the shaver before you clean
it under the tap.
- Always check the appliance before you use
it. Do not use the appliance if it is damaged,
as this may cause injury. Always replace a
damaged part with one of the original type.
- Do not open the appliance to replace the
rechargeable battery.
Caution
- Never immerse the cleaning
system or the charging stand in
water and do not rinse it under
the tap.
- Never use water hotter than
60°C to rinse the shaver.
- Only use this appliance for its
intended purpose as shown in
the user manual.
- For hygienic reasons, the
appliance should only be used
by one person.
English
- Never use compressed air,
scouring pads, abrasive
cleaning agents or aggressive
liquids such as petrol or
acetone to clean the appliance.
- If your shaver comes with a
cleaning system, always use the
original Philips cleaning fluid
(cartridge or bottle, depending
on the type of cleaning system).
- Always place the cleaning
system on a stable, level and
horizontal surface to prevent
leakage.
- If your cleaning system uses a
cleaning cartridge, always make
sure the cartridge compartment
is closed before you use the
cleaning system to clean or
charge the shaver.
- When the cleaning system is
ready for use, do not move it to
prevent leakage of cleaning
fluid.
9
English
10
- Water may drip from the socket
at the bottom of the shaver
when you rinse it. This is normal
and not dangerous because all
electronics are enclosed in a
sealed power unit inside the
shaver.
- Do not use the supply unit in or
near wall sockets that contain
an electric air freshener to
prevent irreparable damage to
the supply unit.
Electromagnetic fields (EMF)
This Philips appliance complies with all applicable
standards and regulations regarding exposure to
electromagnetic fields.
General
- This shaver is waterproof. It is suitable for use in
the bath or shower and for cleaning under the
tap. For safety reasons, the shaver can
therefore only be used without cord.
- The supply unit is suitable for mains voltages
ranging from 100 to 240 volts.
- The supply unit transforms 100-240 volts to a
safe low voltage of less than 24 volts.
The display
Note: Before you use the shaver for the first time,
remove the protective foil from the display.
Charging
Quick charge: When you connect the shaver to the
wall socket, the lights of the battery charge
indicator light up one after another repeatedly.
When the shaver contains enough energy for one
shave, the bottom light of the battery charge
indicator starts to flash slowly.
While the shaver continues to charge, first the
bottom light of the battery charge indicator flashes
and then lights up continuously. Then the second
light flashes and lights up continuously, and so on
until the shaver is fully charged (see 'Battery fully
charged').
Battery fully charged
When the battery is fully charged, all lights of the
battery charge indicator light up white
continuously.
Note: This appliance can only be used without
cord. When you press the on/off button during or
after charging, you hear a sound to indicate that
the shaver is still connected to the wall socket.
Note: When the battery is full, the display switches
off automatically after 30 minutes.
English
11
English
12
Battery low
When the battery is almost empty, the bottom light
of the battery charge indicator flashes orange and
you hear a sound.
Remaining battery charge
The remaining battery charge is shown by the
lights of the battery charge indicator that light up
continuously.
Cleaning reminder
Clean the shaver after every shave for optimal
performance. When you switch off the appliance,
the cleaning reminder flashes to remind you to
clean the appliance.
Travel lock
You can lock the appliance when you are going to
travel. The travel lock prevents the appliance from
being switched on by accident.
Activating the travel lock
1 Press the on/off button for 3 seconds to enter
the travel lock mode.
While you activate the travel lock, the travel lock
symbol lights up white continuously. When the
travel lock is activated, the appliance produces
a sound and the travel lock symbol flashes.
Deactivating the travel lock
1 Press the on/off button for 3 seconds.
The travel lock symbol flashes and then lights
up continuously. The appliance is now ready for
use again.
Note: You can also deactivate the travel lock by
connecting the appliance to the wall socket.
Replacement reminder
For maximum shaving performance, we advise you
to replace the shaving heads every two years.
The appliance is equipped with a replacement
reminder which reminds you to replace the
shaving heads. The shaving unit symbol lights up
white continuously, the arrows flash white and the
appliance beeps to indicate that you have to
replace the shaving heads.
Note: After replacing the shaving heads, you can
reset the replacement reminder by pressing the
on/off button for 7 seconds. If you do not reset the
replacement reminder, the shaver resets
automatically after 9 shaves.
Exclamation mark
Overheating
If the appliance overheats during charging, the
exclamation mark flashes orange. When this
happens, the shaver switches off automatically.
Charging continues once the temperature of the
appliance has decreased to the normal level.
English
13
1
2
English
14
Blocked shaving heads
If the shaving heads are blocked, the exclamation
mark lights up orange continuously. The
replacement reminder and the cleaning reminder
flash white alternately and you hear a sound. In
this case, the motor cannot run because the
shaving heads are soiled or damaged.
If the shaving heads are soiled, you have to clean
them. If the shaving heads are damaged, you have
to replace them.
Charging
Charge the shaver before you use it for the first
time and when the display indicates that the
battery is almost empty. The battery charge is
indicated by the lights of the battery charge
indicator on the display.
When you connect the shaver to the wall socket,
you hear a sound.
Charging takes approx. 1 hour. A fully charged
shaver has a shaving timeof up to 50 minutes.
Note: You cannot use the appliance while it is
charging.
Charging with the supply unit
1 Make sure the appliance is switched off.
2 Put the small plug in the appliance and put the
supply unit in the wall socket.
3 After charging, remove the supply unit from the
wall socket and pull the small plug out of the
appliance.
Using the appliance
Note: This appliance can only be used without
cord.
Switching the appliance on and off
- To switch on the appliance, press the on/off
button once.
The display lights up for a few seconds.
- To switch off the appliance, press the on/off
button once.
The display lights up for a few seconds and
shows the remaining battery charge.
Shaving
Skin adaptation period
Your first shaves may not bring you the result you
expect and your skin may even become slightly
irritated. This is normal. Your skin and beard need
time to adapt to any new shaving system. To allow
your skin to adapt to this new appliance, we advise
you to shave regularly (at least 3 times a week) and
exclusively with this appliance for a period of 3
weeks.
Shaving tips
- For the best results on skin comfort, pre-trim
your beard if you have not shaved for 3 days or
longer.
- Move the shaving heads over your skin in
circular movements.
Dry shaving
1 Switch on the appliance.
The display lights up for a few seconds.
English
15
16
English
2 Move the shaving heads over your skin in
circular movements to catch all hairs growing in
different directions. Make sure each shaving
head is fully in contact with the skin. Exert
gentle pressure for a close, comfortable shave.
Note: Do not press too hard, this can cause skin
irritation.
3 Clean the appliance after use.
Wet shaving
For a more comfortable shave, you can also use
this appliance on a wet face with shaving foam or
shaving gel.
To shave with shaving foam or shaving gel, follow
the steps below:
1 Apply some water to your skin.
2 Apply shaving foam or shaving gel to your skin.
3 Rinse the shaving unit under the tap to ensure
that the shaving unit glides smoothly over your
skin.
4 Switch on the appliance.
5 Move the shaving heads over your skin in
circular movements to catch all hairs growing in
different directions. Make sure each shaving
head is fully in contact with the skin. Exert
gentle pressure for a close, comfortable shave.
Note: Rinse the shaving unit regularly to ensure
that it continues to glide smoothly over your
skin.
6 Dry your face.
7 Clean the appliance after use.
Note: Make sure you rinse all foam or shaving
gel off the appliance.
Using click-on attachments
Note: The accessories supplied may vary for
different products. The box shows the accessories
that have been supplied with your product.
Removing or attaching the click-on attachments
1 Make sure the appliance is switched off.
2 Pull the attachment straight off the appliance.
Note: Do not twist the attachment while you
pull it off the appliance.
English
17
3 Insert the lug of the attachment into the slot in
the top of the appliance. Then press down the
attachment to attach it to the appliance (‘click’).
Using the trimmer attachment
You can use the precision trimmer attachment to
touch up your beard, sideburns and moustache.
18
English
1 Attach the attachment to the appliance (‘click’).
2 Switch on the appliance.
The display lights up for a few seconds.
3 Hold the trimmer attachment perpendicular to
the skin and move the appliance downwards
while you exert gentle pressure.
4 Clean the attachment after use (see 'Cleaning
and maintenance').
Using the cleansing brush attachment
Note: For better shaving results, use the click-on
cleansing brush attachment before shaving.
Use the rotating cleansing brush with your daily
cleansing cream. The cleansing brush removes oil
and dirt, contributing to a healthy and oil-free skin.
We advise you to use it no more than twice a day.
Start with the lowest personal comfort setting to
familiarize yourself with the attachment.
Do not use the appliance on damaged or irritated
skin or on wounds.
1 Place the attachment on the attachment
holder.
2 Attach the attachment to the appliance (‘click’).
20 sec.
20 sec.
20 sec.
English
3 Moisten the attachment with water.
Note: Do not use the appliance with a dry
cleansing brush attachment, as this can irritate
the skin.
4 Moisten your face with water and apply a
cleanser to your face.
5 Place the attachment on your cheek.
6 Switch on the appliance.
7 Gently move the attachment across your skin
from the nose towards the ear. Do not push the
attachment too hard onto the skin to make sure
that the treatment remains comfortable.
Note: Do not cleanse the sensitive area around
your eyes.
8 After approx. 20 seconds, move the appliance
to your other cheek and start cleansing this part
of your face.
9 After approx. 20 seconds, move the appliance
to your forehead and start cleansing this part of
your face. Gently move the brush head from left
to right.
Note: We advise you to not overdo the
cleansing and to not cleanse any zone longer
than 20 seconds.
19
English
20
10 After the treatment, rinse and dry your
face.Your face is now ready for the next step of
your daily skincare routine.
11 Switch off the appliance and clean the
attachment after use.
Cleaning and maintenance
Note: The accessories supplied may vary for
different products. The box shows the accessories
that have been supplied with your product.
Cleaning the shaver under the tap
Clean the shaver after every shave for optimal
performance.
Be careful with hot water. Always check if the
water is not too hot, to prevent burning your
hands.
Note: Never dry the shaving unit with a towel or
tissue, as this may damage the shaving heads.
1 Switch on the appliance.
2 Rinse the shaving unit under a warm tap.
3 Switch off the appliance. Pull the shaving head
holder off the bottom part of the shaving unit.
4 Rinse the hair chamber under the tap.
5 Rinse the shaving head holder under a warm
6 Carefully shake off excess water and let the
7 Attach the shaving head holder to the bottom
Thorough cleaning
We advise you to clean the shaving heads
thoroughly once a month or when the shaver does
not shave as well as it used to.
Note: The shaving heads are locked by a blue or an
orange retaining ring.
English
tap.
shaving head holder air-dry completely.
part of the shaving unit (‘click’).
21
Follow the correct instructions.
1 Switch off the shaver.
2
1
2
1
22
English
2 Pull the shaving head holder off the bottom
part of the shaving unit.
3 Rinse the hair chamber and shaving head
holder under the tap.
4 Turn the retaining ring anticlockwise and lift it
off the shaving head.
Repeat this process for the other retaining rings.
Place them aside in a safe place.
5 Remove the shaving heads from the shaving
head holder. Each shaving head consists of a
cutter and guard.
Note: Do not clean more than one cutter and
guard at a time, since they are all matching sets.
If you accidentally put a cutter in the wrong
shaving guard, it may take several weeks before
optimal shaving performance is restored.
2
1
1
2
English
6 Clean the cutter and guard under the tap.
7 Shake off excess water.
8 Put the cutter back into the guard.
9 Place the shaving heads in the shaving head
holder.
Note: Make sure the notches on both sides of
the shaving heads fit exactly onto the
projections in the shaving head holder.
10 Blue retaining ring: Place the retaining ring on
the shaving head and turn it clockwise to
reattach the retaining ring.
Place the arrows on the ring in line with the
projections in the shaving head holder. Turn the
ring clockwise until it clicks to indicate that the
ring is fixed.
- Orange retaining ring: Place the retaining ring
on the shaving head and turn it clockwise to
reattach the retaining ring. Repeat this process
for the other retaining rings.
23
2
1
English
24
Each retaining ring has two recesses that fit
exactly into the projections of the shaving head
holder. Turn the ring clockwise until your hear a
click to indicate that the ring is fixed.
Hold the shaving head holder in your hand
when you reinsert the shaving heads and
reattach the retaining rings. Do not place the
shaving head holder on a surface when you do
this, as this may cause damage.
11 Attach the shaving head holder to the bottom
part of the shaving unit (‘click’).
Cleaning the click-on attachments
Note: Never dry the trimmer attachment with a
towel or tissue, as this may damage the trimming
teeth.
Cleaning the trimmer attachment
Never dry the trimmer with a towel or tissue, as
this may damage the trimming teeth.
Clean the trimmer attachment after each use.
1 Switch on the appliance with the precision
trimmer attachment attached.
2 Rinse the attachment under a warm tap.
3 After cleaning, switch off the appliance.
4 Carefully shake off excess water and let the
attachment air-dry completely.
Tip: For optimal performance, lubricate the teeth
of the attachment with a drop of sewing machine
oil regularly.
Cleaning the cleansing brush attachment
Clean the cleansing brush attachment after each
use.
1 Switch off the appliance.
2 Detach the attachment from the attachment
2yrs
3 Clean the parts thoroughly with warm water
4 Dry the attachment with a towel.
Storage
- Store the appliance in the pouch supplied.
- Put the protection cap on the cleansing brush
Replacement
Replacing the shaving heads
For maximum shaving performance, we advise you
to replace the shaving heads every two years.
Replace damaged shaving heads immediately.
Always replace the shaving heads with original
Philips shaving heads ( 'Ordering accessories').
Replacement reminder
The replacement reminder indicates that the
shaving heads need to be replaced. The shaving
unit symbol lights up continuously, the arrows
flash white and you hear a beep when you switch
off the shaver.
English
holder.
and soap.
Note: Make sure the appliance is dry before you
store it in the pouch.
attachment to protect it from dirt accumulation.
25
English
26
1 To replace the shaving heads, remove the
shaving heads from the shaving head holder
one by one. See chapter Thorough Cleaning for
the instructions on how to remove the retaining
rings and shaving heads.
Note: The shaving heads are locked by a blue or
an orange retaining ring. Follow the correct
instructions.
2 To reset the replacement reminder, press and
hold the on/off button for approx. 7 seconds.
Wait until you hear two beeps.
Replacing the cleansing brush attachment
The cleansing brush attachment should be
replaced every 3 months or earlier if the brush
hairs are bent or damaged (see 'Ordering
accessories').
Ordering accessories
To buy accessories or spare parts, visit
www.shop.philips.com/service or go to your
Philips dealer. You can also contact the Philips
Consumer Care Center in your country (see the
international warranty leaflet for contact details).
The following accessories and spare parts are
available:
- SH90 Philips shaving heads
- HQ110 Philips shaving head cleaning spray
- RQ111 Philips beard styler attachment
- RQ585 Philips cleansing brush attachment
- RQ560/RQ563Philips cleansing brush heads
- JC301/JC302/JC303/JC304/JC305cleaning
cartridge
- HQ8505 supply unit
Note: The availability of the accessories may differ
by country.
Recycling
- This symbol means that this product shall not
be disposed of with normal household waste
(2012/19/EU).
- This symbol means that this product contains a
built-in rechargeable battery which shall not be
disposed of with normal household waste
(2006/66/EC). Please take your product to an
official collection point or a Philips service
center to have a professional remove the
rechargeable battery.
- Follow your country’s rules for the separate
collection of electrical and electronic products
and rechargeable batteries. Correct disposal
helps prevent negative consequences for the
environment and human health.
Removing the rechargeable shaver battery
Only remove the rechargeable battery when
you discard the shaver. Before you remove
the battery, make sure that the shaver is
disconnected from the wall socket and that
the battery is completely empty.
English
27
English
28
Take any necessary safety precautions
when you handle tools to open the shaver
and when you dispose of the rechargeable
battery.
Be careful, the battery strips are sharp.
1 Insert the screwdriver into the slot between the
front and back panel in the bottom of the
appliance. Remove the back panel.
2 Remove the front panel.
3 Unscrew the two screws at the top of the inner
panel and remove the inner panel.
4 Bend aside the battery lips, which hold the
battery, by placing a screwdriver between the
battery and the lips.
5 Remove the battery.
Warranty and support
If you need information or support, please visit
www.philips.com/support or read the
international warranty leaflet.
Warranty restrictions
The shaving heads (cutters and guards) are not
covered by the terms of the international warranty
because they are subject to wear.
Troubleshooting
This chapter summarizes the most common
problems you could encounter with the appliance.
If you are unable to solve the problem with the
information below, visit www.philips.com/support
for a list of frequently asked questions or contact
the Consumer Care Center in your country.
Shaver
Problem Possible cause Solution
English
29
The appliance
does not work
when I press the
on/off button.
The rechargeable
The travel lock is
Theapplianced
oes not shave as
well as it used to.
Hairs or dirt
I replaced the
shaving heads,
but the display
still shows the
replacement
reminder.
A shaving unit
symbol has
suddenly
appeared on the
display.
The appliance is still
attached to the wall
socket. For safety
reasons, the
appliance can only
be used without
cord.
battery is empty.
activated.
The shaving unit is
soiled or damaged
to such an extent
that the motor
cannot run.
The shaving heads
are damaged or
worn.
obstruct the shaving
heads.
You have not reset
the appliance.
This symbol
reminds you to
replace the shaving
heads.
Unplug the appliance and
press the on/off button to
switch on the appliance.
Recharge the battery (see
'Charging').
Press the on/off button for
3 seconds to deactivate the
travel lock.
Clean the shaving heads
thoroughly or replace them.
Replace the shaving heads
(see 'Replacement').
Clean the shaving heads in
the regular way or clean
them thoroughly.
Reset the appliance by
pressing the on/off button
for approx. 7 seconds.
Replace the shaving heads
(see 'Replacement').
English
30
Problem Possible cause Solution
An exclamation
mark has
suddenly
appeared on the
display while the
appliance is
charging.
An exclamation
mark, the
replacement
reminderand
the cleaning
reminder have
suddenly
appeared on the
display.
The shaving heads
Water is leaking
from the bottom
of the appliance.
The appliance is
overheated.
The shaving heads
are damaged.
are soiled.
During cleaning,
water may collect
between the inner
body and the outer
shell of the
appliance.
Disconnect the appliance
from the wall socket for
approx. 10 minutes.
Replace the shaving heads
(see 'Replacement').
Clean the shaving heads
(see 'Cleaning and
maintenance').
This is normal and not
dangerous because all
electronics are enclosed in
a sealed power unit inside
the appliance.
Loading...