PicoPix Micro
Portable projector
PPX320/321/322
User Manual
Register your product and get support at
www.philips.com/support
Table of contents
Introduction �������������������������������������������������3
Dear customer ...............................................................3
About this user manual ..............................................3
What’s in the box ..........................................................3
Customer service centre ............................................3
1 General safety information ��������������� 4
Setting up the product .............................................. 4
Repairs ............................................................................ 4
Power supply .................................................................5
2 Overview ������������������������������������������������5
Rear view .........................................................................5
Side view ......................................................................... 6
3 Connect ������������������������������������������������� 6
HDMI connection for image projection ............... 6
4 Operation �����������������������������������������������7
Place the projector.......................................................7
Connecting power supply .........................................7
Power on and setup ....................................................7
Connecting to external speakers or headphones
............................................................................................ 8
Placement options ...................................................... 8
5 Change settings ����������������������������������10
Language settings ......................................................10
Picture settings ............................................................10
Power control settings ..............................................10
Restore default settings ............................................11
Other settings ...............................................................11
6 Service ���������������������������������������������������11
Built-in battery care ...................................................11
Cleaning ..........................................................................11
Update software .........................................................12
Troubleshooting .......................................................... 13
7 Appendix ���������������������������������������������� 14
Technical data .............................................................14
CE statement ...............................................................15
FCC statement .............................................................15
Canada regulatory compliance ............................. 15
Other notice ..................................................................15
Introduction
a
Dear customer
Thank you for purchasing this projector.
We hope you enjoy this product and the many
functions it offers!
About this user manual
The quick start guide supplied with this product
allows you to start using this product quickly
and easily. Detailed descriptions can be found
in the following sections of this user manual.
Read the entire user manual carefully. Follow
all safety instructions in order to ensure proper
operation of this product (see General safety
information, page 4). The manufacturer
accepts no liability if these instructions are not
followed.
Symbols used
Notice
Troubleshooting
This symbol indicates tips that will help
you in using this product more effectively
and easily.
DANGER!
Danger of personal injury!
This symbol gives warning of danger
of personal injury. Physical injury or
damage can result from improper
handling.
CAUTION!
Damage to the product or loss of data!
This symbol gives warning of damage
to the product and possible loss of
data. Damage can result from improper
handling.
What’s in the box
PicoPix Micro projector (PPX320/321/322)
a
USB cable
b
Quick Start Guide
c
c
b
Quick Start
Guide
Customer service centre
You can find the support hotline in the warranty
card or online:
Web: www.philips.com/support
Mail: philips.projector.eu@screeneo.com
International Phone: +41 215 391 665
Please ask your provider for international call
costs!
Access the electronic user manual at
https://support.screeneo.com
Access the community forum at
https://community.screeneo.com
Introduction 3
1 General safety
information
Take note of all warning and safety notes
indicated. Do not make any changes or settings
that are not described in this user manual.
Incorrect operation, and improper handling can
lead to physical injury, damage to the product
or loss of data.
Setting up the product
This product is for indoor use only. Place the
product securely on a stable, flat surface.
To help avoid possible injuries to persons or
damage to the product itself, position all cables
in such a way that no one will trip over them.
Do not operate the product in damp rooms.
Never touch the mains cable or the mains
connection with wet hands.
The product must have sufficient ventilation
and must not be covered. Do not put the
product in closed cabinets, boxes, or other
enclosures when in use.
Protect the product from direct sunlight,
heat, intense temperature fluctuations and
moisture. Do not place the product in the
vicinity of heaters or air conditioners. Observe
the information on temperature listed in the
technical data (see Technical data, page 14).
Prolonged operation of the product causes the
surface to become hot. In case of overheating,
the product automatically switches to standby
mode.
Do not allow liquids to leak into the product.
Turn off the product and disconnect it from the
mains supply if liquids or foreign substances
leaked into the product. Have the product
inspected by an authorised service centre.
Always handle the product with care. Avoid
touching the lens. Never place heavy or sharp
objects on the product or on the power cable.
If the product gets too hot or emits smoke,
shut it down immediately and unplug the
power cable. Have your product checked by
an authorised service centre. Keep the product
away from open flames (e.g. candles).
The product has built-in battery. Do not
dissemble and modify. The built-in battery
should be replaced by qualified service staff
only.
Do not try to replace the built-in battery
yourself. Incorrect handling of the battery or
using the wrong type of battery can cause
damage to the product or cause injury.
DANGER!
Risk of explosion with incorrect type
of batteries!
There is a risk of explosion if the wrong
battery type is used.
Do not expose the batteries (battery pack or
embedded batteries) to excessive heat such as
sunshine, or open fire.
Under the following conditions, a layer of
moisture can appear inside the product which
can lead to malfunctions:
• if the product is moved from a cold to a
warm area;
• after a cold room is heated;
• when the product is placed in a damp
room.
Proceed as follows to avoid any moisture
buildup:
1 Seal the product in a plastic bag before
moving it to another room, in order for it to
adapt to room conditions.
2 Wait one to two hours before you take the
product out of the plastic bag.
The product should not be used in a very dusty
environment. Dust particles and other foreign
objects may damage the product.
Do not expose the product to extreme
vibrations. This may damage the internal
components.
Do not allow children to handle the product
without supervision. The packing materials
should be kept out of the hands of children.
For your own safety, do not use the product
during thunderstorms with lightning.
Repairs
Do not repair the product yourself. Improper
maintenance can result in injuries or damage to
the product. The product must be repaired by
an authorised service centre.
Please find the details of authorised service
centres on the warranty card supplied with this
product.
Do not remove the type label from this product,
as this will void the warranty.
4 Philips · PicoPix Micro
Power supply
Use only a certified power adapter. Check
whether the mains voltage of the power supply
matches the mains voltage available at the
setup location. This product complies with the
voltage type specified on the product.
The power outlet shall be installed near the
product and shall be easily accessible.
The capacity of the built-in battery diminishes
with time. If the product functions only with
external power supply, the built-in battery is
defective. Contact an authorised service centre
to replace the built-in battery.
CAUTION!
Always use the button to turn the
projector off.
2 Overview
Rear view
cba d e
USB
h fg
HDMI
Turn off the product and unplug from the
power outlet before cleaning the surface
(see Cleaning, page 11). Use a soft, lintfree cloth. Never use liquid, gaseous or easily
flammable cleaners (sprays, abrasives, polishes,
alcohol). Do not allow any moisture to reach
the interior of the product.
DANGER!
Risk of eye irritation!
This product is equipped with a high
power LED (Light Emitting Diode),
which emits very bright light. Do not
look directly into the projector lens
during operation. This could cause eye
irritation or damage.
Reset key
a
Reset the projector to the factory default
settings (use a small pin to press the reset
key).
IR sensor
b
Micro USB port
c
Connect to the power supply.
d
3.5 mm audio output; connect to external
speakers or headphones.
Mini HDMI port
e
Connect to the HDMI output on a playback
device.
f
• Press and hold three seconds to switch
the projector on or off.
• Access the settings menu.
• Confirm a selection or entry.
• When the projector is switched on, the
LED turns blue. When the projector is
switched off, the LED turns off.
• When charging the projector, the LED
turns red regardless of the projector
switching on or off.
/
g
• Navigate menu options.
• Increase or decrease volume.
h
Return to a previous menu screen.
Overview 5
Side view
USB
HDMI
Focus adjustment knob
a
Adjust image sharpness.
3 Connect
Notice
You need to connect the projector to
an HDMI device, so that the projection
screen can show images.
Make sure all devices are disconnected
from the power outlet before establishing
or changing any connections.
a
HDMI connection for image
projection
Connect a playback device (e.g. a Blu-ray
player, gaming console, camcorder, digital
camera or PC) to the projector through HDMI
connection. With this connection, images are
shown on the projection screen, and audio is
played on the projector.
• Using an HDMI cable, connect the HDMI
connector (mini HDMI port) on the projector
to the HDMI output on the playback device.
Use an HDMI mini plug adapter for HDMI
connection if necessary.
6 Philips · PicoPix Micro
Loading...