Philips P89C52UBPN, P89C54UBAA, P89C51UBPN, P89C51UBAA, P89C54NBPN Datasheet

...

 

89C51/89C52/89C54/89C58

80C51 8-bit microcontroller family 4K/8K/16K/32K Flash

Product specification

Replaces Datasheets 89C51 of 1999 Apr 01 and 89C52/89C54/89C58 of 1999 Apr 01

1999 Oct 27

INTEGRATED CIRCUITS

Philips Semiconductors Product specification

89C51/89C52/89C54/89C58

80C51 8-bit microcontroller family 4K/8K/16K/32K Flash

1999 Oct 27 853–2148 22592

DESCRIPTION

The 89C51/89C52/89C54/89C58 contain a non-volatile FLASH program memory that is parallel programmable. For devices that are serial programmable (In System Programmable (ISP) with a boot loader), see the 89C51RC+/89C51RD+ datasheet.

Both families are Single-Chip 8-bit Microcontrollers manufactured in advanced CMOS process and are derivatives of the 80C51 microcontroller family. All the devices have the same instruction set as the 80C51.

SELECTION T ABLE FOR FLASH DEVICES

ROM/EPROM Memory Size

(X by 8)

RAM Size

(X by 8)

Programmable

Timer Counter

(PCA)

Hardware

Watchdog

Timer Multi-Time Programmable (MTP) devices: 89C51

4 k 128 No No

89C52/54/58

8 k/16 k/32 k 256 No No

Serial In-System Programmable devices:

89C51RC+

32 k 512 Yes Yes

89C51RD+

64 k 1024 Yes Yes

FEATURES

•80C51 Central Processing Unit

•On-chip FLASH Program Memory

•Speed up to 33 MHz

•Full static operation

•RAM expandable externally to 64 k bytes

•4 level priority interrupt

•6 interrupt sources

•Four 8-bit I/O ports

•Full-duplex enhanced UART

– Framing error detection – Automatic address recognition

•Power control modes

– Clock can be stopped and resumed – Idle mode – Power down mode

•Programmable clock out

•Second DPTR register

•Asynchronous port reset

•Low EMI (inhibit ALE)

•3 16-bit timers

•Wake up from power down by an external interrupt

ORDERING INFORMATION

MEMORY SIZE

4 k × 8

MEMORY SIZE

8 k × 8

MEMORY SIZE

16 k × 8

MEMORY SIZE

32 k × 8

TEMPERATURE

RANGE °C

AND PACKAGE

VOLTAGE

RANGE

FREQ.

(MHz)

DWG.

FLASH P89C51UBA A P89C52UBA A P89C54UBA A P89C58UBA A

0 to +70, Plastic

Leaded Chip Carrier

5 V 0 to 33 SOT187-2

FLASH P89C51UBP N P89C52UBP N P89C54UBP N P89C58UBP N

0 to +70, Plastic

Dual In-line Package

5 V 0 to 33 SOT129-1

FLASH P89C51UBB B P89C52UBB B P89C54UBB B P89C58UBB B

0 to +70, Plastic

Quad Flat Pack

5 V 0 to 33 QFP44

FLASH P89C51UFA A P89C52UFA A P89C54UFA A P89C58UFA A

–40 to +85, Plastic

Leaded Chip Carrier

5 V 0 to 33 SOT187-2

FLASH P89C51UFP N P89C52UFP N P89C54UFP N P89C58UFP N

–40 to +85, Plastic

Dual In-line Package

5 V 0 to 33 SOT129-1

FLASH P89C51UFB B P89C52UFB B P89C54UFB B P89C58UFB B

–40 to +85, Plastic

Quad Flat Pack

5 V 0 to 33 QFP44

NOTES:

1. Contact Philips Sales for availability.

2. SOT not assigned for this package outline.

P ART NUMBER DERIVATION

DEVICE NUMBER (P89CXX) OPERATING FREQUENCY, MAX (V) TEMPERATURE RANGE (B) PACKAGE (AA, BB, PN)

P89C51 FLASH P89C52 FLASH P89C54 FLASH P89C58 FLASH

U = 33 MHz

B = 0_C to 70_C

F = –40_C to 85_C

AA = PLCC BB = PQFP

PN = PDIP

Philips Semiconductors Product specification

89C51/89C52/89C54/89C58

80C51 8-bit microcontroller family 4K/8K/16K/32K Flash

1999 Oct 27

BLOCK DIAGRAM

SU01066

PSEN

EAV

ALE

RST

XTAL1 XTAL2

PORT 0

DRIVERS

PORT 2

DRIVERS

RAM ADDR REGISTER

RAM

PORT 0

LATCH

PORT 2

LATCH

FLASH

ACC

STACK

POINTER

TMP2

TMP1

ALU

TIMING

AND

CONTROL

INSTRUCTION

OSCILLATOR

PSW

PORT 1

LATCH

PORT 3

LATCH

PORT 1

DRIVERS

PORT 3

DRIVERS

PROGRAM

ADDRESS

BUFFER

INCRE-

MENTER

PROGRAM COUNTER

DPTR’S

MULTIPLE

P1.0–P1.7

P3.0–P3.7

P0.0–P0.7 P2.0–P2.7

SFRs

TIMERS

8 16

Philips Semiconductors Product specification

89C51/89C52/89C54/89C58

80C51 8-bit microcontroller family 4K/8K/16K/32K Flash

1999 Oct 27

LOGIC SYMBOL

PORT 0

PORT 1PORT 2

PORT 3

ADDRESS AND

DATA BUS

ADDRESS BUS

T2 T2EX

RxD

TxD INT0 INT1

T0 T1

SECONDARY FUNCTIONS

RST

EA/V

PSEN

ALE/PROG

XTAL1

XTAL2

SU00830

PIN CONFIGURA TIONS Dual In-Line Package Pin Functions

SU01063

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 17 18 19 20

T2/P1.0

T2EX/P1.1

P1.2 P1.3 P1.4 P1.5 P1.6

RST RxD/P3.0 TxD/P3.1

INT0

/P3.2

INT1

/P3.3 T0/P3.4 T1/P3.5

P1.7

/P3.6 RD

/P3.7

XTAL2 XTAL1

P2.0/A8

P2.1/A9

P2.2/A10

P2.3/A11

P2.4/A12

P2.5/A13

P2.6/A14

P2.7/A15

PSEN

ALE

P0.7/AD7

P0.6/AD6

P0.5/AD5

P0.4/AD4

P0.3/AD3

P0.2/AD2

P0.1/AD1

P0.0/AD0

DUAL

IN-LINE

PACKAGE

Ceramic and Plastic Leaded Chip Carrier Pin Functions

SU01062

LCC

6140

18 28

Pin Function

1 NIC* 2 P1.0/T2 3 P1.1/T2EX 4 P1.2 5 P1.3 6 P1.4 7 P1.5 8 P1.6

9 P1.7 10 RST 11 P3.0/RxD 12 NIC* 13 P3.1/TxD 14 P3.2/INT0 15 P3.3/INT1

Pin Function

16 P3.4/T0 17 P3.5/T1 18 P3.6/WR 19 P3.7/RD 20 XTAL2 21 XTAL1 22 V

23 NIC* 24 P2.0/A8 25 P2.1/A9 26 P2.2/A10 27 P2.3/A11 28 P2.4/A12 29 P2.5/A13 30 P2.6/A14

Pin Function

31 P2.7/A15 32 PSEN 33 ALE 34 NIC* 35 EA/V

36 P0.7/AD7 37 P0.6/AD6 38 P0.5/AD5 39 P0.4/AD4 40 P0.3/AD3 41 P0.2/AD2 42 P0.1/AD1 43 P0.0/AD0 44 V

* NO INTERNAL CONNECTION

Plastic Quad Flat Pack Pin Functions

SU01064

PQFP

44 34

12 22

Pin Function

1 P1.5 2 P1.6 3 P1.7 4 RST 5 P3.0/RxD 6 NIC* 7 P3.1/TxD 8 P3.2/INT0

9 P3.3/INT1 10 P3.4/T0 11 P3.5/T1 12 P3.6/WR 13 P3.7/RD 14 XTAL2 15 XTAL1

Pin Function

16 V

17 NIC* 18 P2.0/A8 19 P2.1/A9 20 P2.2/A10 21 P2.3/A11 22 P2.4/A12 23 P2.5/A13 24 P2.6/A14 25 P2.7/A15 26 PSEN 27 ALE 28 NIC* 29 EA

30 P0.7/AD7

Pin Function

31 P0.6/AD6 32 P0.5/AD5 33 P0.4/AD4 34 P0.3/AD3 35 P0.2/AD2 36 P0.1/AD1 37 P0.0/AD0 38 V

39 NIC* 40 P1.0/T2 41 P1.1/T2EX 42 P1.2 43 P1.3 44 P1.4

* NO INTERNAL CONNECTION

Philips Semiconductors Product specification

89C51/89C52/89C54/89C58

80C51 8-bit microcontroller family 4K/8K/16K/32K Flash

1999 Oct 27

PIN DESCRIPTIONS

PIN NUMBER

MNEMONIC DIP LCC QFP TYPE NAME AND FUNCTION

20 22 16 I Ground: 0 V reference.

40 44 38 I Power Supply: This is the power supply voltage for normal, idle, and power-down operation.

P0.0–0.7 39–32 43–36 37–30 I/O Port 0: Port 0 is an open-drain, bidirectional I/O port. Port 0 pins that have 1s written to

them float and can be used as high-impedance inputs. Port 0 is also the multiplexed low-order address and data bus during accesses to external program and data memory. In this application, it uses strong internal pull-ups when emitting 1s.

P1.0–P1.7 1–8 2–9 40–44,

1–3

I/O Port 1: Port 1 is an 8-bit bidirectional I/O port with internal pull-ups. Port 1 pins that have 1s

written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 1 pins that are externally pulled low will source current because of the internal pull-ups. (See DC Electrical Characteristics: I

). Alternate function for Port 1: 1 2 40 I/O T2 (P1.0): Timer/Counter2 external count input/clockout (see Programmable Clock-Out). 2 3 41 I T2EX (P1.1): Timer/Counter2 reload/capture/direction control.

P2.0–P2.7 21–28 24–31 18–25 I/O Port 2: Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. Port 2 pins that have 1s

written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 2 pins that are externally being pulled low will source current because of the internal pull-ups. (See DC Electrical Characteristics: I

). Port 2 emits the high-order address byte during fetches from external program memory and during accesses to external data memory that use 16-bit addresses (MOVX @DPTR). In this application, it uses strong internal pull-ups when emitting 1s. During accesses to external data memory that use 8-bit addresses (MOV @Ri), port 2 emits the contents of the P2 special function register.

P3.0–P3.7 10–17 11,

13–195,7–13

I/O Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3 pins that have 1s

written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 3 pins that are externally being pulled low will source current because of the pull-ups. (See DC Electrical Characteristics: I

). Port 3 also serves the special features of the

89C51/89C52/89C54/89C58, as listed below:

10 11 5 I RxD (P3.0): Serial input port 11 13 7 O TxD (P3.1): Serial output port 12 14 8 I INT0 (P3.2): External interrupt 13 15 9 I INT1 (P3.3): External interrupt 14 16 10 I T0 (P3.4): Timer 0 external input 15 17 11 I T1 (P3.5): Timer 1 external input 16 18 12 O WR (P3.6): External data memory write strobe 17 19 13 O RD (P3.7): External data memory read strobe

RST 9 10 4 I Reset: A high on this pin for two machine cycles while the oscillator is running, resets the

device. An internal diffused resistor to V

permits a power-on reset using only an external

capacitor to V

ALE 30 33 27 O Address Latch Enable: Output pulse for latching the low byte of the address during an

access to external memory. In normal operation, ALE is emitted at a constant rate of 1/6 the oscillator frequency , and can be used for external timing or clocking. Note that one ALE pulse is skipped during each access to external data memory. ALE can be disabled by setting SFR auxiliary.0. With this bit set, ALE will be active only during a MOVX instruction.

PSEN 29 32 26 O Program Store Enable: The read strobe to external program memory. When executing

code from the external program memory, PSEN

is activated twice each machine cycle,

except that two PSEN

activations are skipped during each access to external data memory.

PSEN

is not activated during fetches from internal program memory.

EA/V

31 35 29 I External Access Enable/Programming Supply Voltage: EA must be externally held low

to enable the device to fetch code from external program memory locations 0000H to the maximum internal memory boundary. If EA

is held high, the device executes from internal program memory unless the program counter contains an address greater than 0FFFH for 4 k devices, 1FFFH for 8 k devices, 3FFFH for 16 k devices, and 7FFFH for 32 k devices. The value on the EA

pin is latched when RST is released and any subsequent changes

have no effect. This pin also receives the 12.00 V programming supply voltage (V

) during

FLASH programming.

XTAL1 19 21 15 I Crystal 1: Input to the inverting oscillator amplifier and input to the internal clock

generator circuits.

XTAL2 18 20 14 O Crystal 2: Output from the inverting oscillator amplifier.

NOTE: To avoid “latch-up” effect at power-on, the voltage on any pin (other than VPP) at any time must not be higher than VCC + 0.5 V or V

– 0.5 V , respectively.

Philips Semiconductors Product specification

89C51/89C52/89C54/89C58

80C51 8-bit microcontroller family 4K/8K/16K/32K Flash

1999 Oct 27

Table 1. 89C51/89C52/89C54/89C58 Special Function Registers

SYMBOL DESCRIPTION

DIRECT

ADDRESS

BIT ADDRESS, SYMBOL, OR ALTERNATIVE PORT FUNCTION

MSB LSB

RESET VALUE

ACC* Accumulator E0H E7 E6 E5 E4 E3 E2 E1 E0 00H AUXR# Auxiliary 8EH – – – – – – – AO xxxxxxx0B AUXR1# Auxiliary 1 A2H – – – – GF2 0 – DPS xxxx00x0B B* B register F0H F7 F6 F5 F4 F3 F2 F1 F0 00H DPTR: Data Pointer (2 bytes)

DPH Data Pointer High 83H 00H DPL Data Pointer Low 82H 00H

AF AE AD AC AB AA A9 A8

IE* Interrupt Enable A8H EA – ET2 ES ET1 EX1 ET0 EX0 0x000000B

BF BE BD BC BB BA B9 B8

IP* Interrupt Priority B8H – – PT2 PS PT1 PX1 PT0 PX0 xx000000B

B7 B6 B5 B4 B3 B2 B1 B0

IPH# Interrupt Priority High B7H – – PT2H PSH PT1H PX1H PT0H PX0H xx000000B

87 86 85 84 83 82 81 80

P0* Port 0 80H AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 FFH

97 96 95 94 93 92 91 90

P1* Port 1 90H – – – – – – T2EX T2 FFH

A7 A6 A5 A4 A3 A2 A1 A0

P2* Port 2 A0H AD15 AD14 AD13 AD12 AD1 1 AD10 AD9 AD8 FFH

B7 B6 B5 B4 B3 B2 B1 B0

P3* Port 3 B0H RD WR T1 T0 INT1 INT0 TxD RxD FFH

PCON#1Power Control 87H SMOD1 SMOD0 – POF

GF1 GF0 PD IDL 00xxx000B

D7 D6 D5 D4 D3 D2 D1 D0

PSW* Program Status Word D0H CY AC F0 RS1 RS0 OV – P 000000x0B

RACAP2H# Timer 2 Capture High CBH 00H RACAP2L# Timer 2 Capture Low CAH 00H

SADDR# Slave Address A9H 00H SADEN# Slave Address Mask B9H 00H

SBUF Serial Data Buffer 99H xxxxxxxxB

9F 9E 9D 9C 9B 9A 99 98

SCON* Serial Control 98H

SM0/FE

SM1 SM2 REN TB8 RB8 TI RI 00H

SP Stack Pointer 81H 07H

8F 8E 8D 8C 8B 8A 89 88

TCON* Timer Control 88H TF1 TR1 TF0 TR0 IE1 IT1 IE0 IT0 00H

CF CE CD CC CB CA C9 C8 T2CON* Timer 2 Control C8H TF2 EXF2 RCLK TCLK EXEN2 TR2 C/T2 CP/RL2 00H T2MOD# Timer 2 Mode Control C9H – – – – – – T2OE DCEN xxxxxx00B

TH0 Timer High 0 8CH 00H TH1 Timer High 1 8DH 00H TH2# Timer High 2 CDH 00H TL0 Timer Low 0 8AH 00H TL1 Timer Low 1 8BH 00H TL2# Timer Low 2 CCH 00H

TMOD T imer Mode 89H GATE C/T M1 M0 GATE C/T M1 M0 00H

* SFRs are bit addressable. # SFRs are modified from or added to the 80C51 SFRs. – Reserved bits.

1. Reset value depends on reset source.

2. Bit will not be affected by reset.

Philips Semiconductors Product specification

89C51/89C52/89C54/89C58

80C51 8-bit microcontroller family 4K/8K/16K/32K Flash

1999 Oct 27

FLASH EPROM MEMORY General Description

The 89C51/89C52/89C54/89C58 FLASH reliably stores memory contents even after 100 erase and program cycles. The cell is designed to optimize the erase and programming mechanisms. In addition, the combination of advanced tunnel oxide processing and low internal electric fields for erase and programming operations produces reliable cycling.

Features

•FLASH EPROM internal program memory with Chip Erase

•Up to 64 k byte external program memory if the internal program

memory is disabled (EA

= 0)

•Programmable security bits

•100 minimum erase/program cycles for each byte

•10 year minimum data retention

•Programming support available from many popular vendors

OSCILLA T OR CHARACTERISTICS

XTAL1 and XTAL2 are the input and output, respectively, of an inverting amplifier. The pins can be configured for use as an on-chip oscillator.

To drive the device from an external clock source, XTAL1 should be driven while XTAL2 is left unconnected. There are no requirements on the duty cycle of the external clock signal, because the input to the internal clock circuitry is through a divide-by-two flip-flop. However, minimum and maximum high and low times specified in the data sheet must be observed.

RESET

A reset is accomplished by holding the RST pin high for at least two machine cycles (24 oscillator periods), while the oscillator is running. To insure a good power-on reset, the RST pin must be high long enough to allow the oscillator time to start up (normally a few milliseconds) plus two machine cycles. At power-on, the voltage on V

and RST must come up at the same time for a proper start-up. Ports 1, 2, and 3 will asynchronously be driven to their reset condition when a voltage above V

IH1

(min.) is applied to RESET.

The value on the EA

pin is latched when RST is deasserted and has

no further effect.

Philips Semiconductors Product specification

89C51/89C52/89C54/89C58

80C51 8-bit microcontroller family 4K/8K/16K/32K Flash

1999 Oct 27

LOW POWER MODES Stop Clock Mode

The static design enables the clock speed to be reduced down to 0 MHz (stopped). When the oscillator is stopped, the RAM and Special Function Registers retain their values. This mode allows step-by-step utilization and permits reduced system power consumption by lowering the clock frequency down to any value. For lowest power consumption the Power Down mode is suggested.

Idle Mode

In the idle mode (see Table 2), the CPU puts itself to sleep while all of the on-chip peripherals stay active. The instruction to invoke the idle mode is the last instruction executed in the normal operating mode before the idle mode is activated. The CPU contents, the on-chip RAM, and all of the special function registers remain intact during this mode. The idle mode can be terminated either by any enabled interrupt (at which time the process is picked up at the interrupt service routine and continued), or by a hardware reset which starts the processor in the same manner as a power-on reset.

Power-Down Mode

To save even more power, a Power Down mode (see Table 2) can be invoked by software. In this mode, the oscillator is stopped and the instruction that invoked Power Down is the last instruction executed. The on-chip RAM and Special Function Registers retain their values down to 2.0 V and care must be taken to return V

to the minimum specified operating voltages before the Power Down Mode is terminated.

Either a hardware reset or external interrupt can be used to exit from Power Down. Reset redefines all the SFRs but does not change the on-chip RAM. An external interrupt allows both the SFRs and the on-chip RAM to retain their values.

To properly terminate Power Down the reset or external interrupt should not be executed before V

is restored to its normal operating level and must be held active long enough for the oscillator to restart and stabilize (normally less than 10ms).

With an external interrupt, INT0 and INT1 must be enabled and configured as level-sensitive. Holding the pin low restarts the oscillator but bringing the pin back high completes the exit. Once the interrupt is serviced, the next instruction to be executed after RETI will be the one following the instruction that put the device into Power Down.

Design Consideration

•When the idle mode is terminated by a hardware reset, the device

normally resumes program execution, from where it left off, up to two machine cycles before the internal reset algorithm takes control. On-chip hardware inhibits access to internal RAM in this event, but access to the port pins is not inhibited. To eliminate the possibility of an unexpected write when Idle is terminated by reset, the instruction following the one that invokes Idle should not be one that writes to a port pin or to external memory.

ONCE Mode

The ONCE (“On-Circuit Emulation”) Mode facilitates testing and debugging of systems without the device having to be removed from the circuit. The ONCE Mode is invoked by:

1. Pull ALE low while the device is in reset and PSEN

is high;

2. Hold ALE low as RST is deactivated. While the device is in ONCE Mode, the Port 0 pins go into a float

state, and the other port pins and ALE and PSEN

are weakly pulled high. The oscillator circuit remains active. While the device is in this mode, an emulator or test CPU can be used to drive the circuit. Normal operation is restored when a normal reset is applied.

Programmable Clock-Out

A 50% duty cycle clock can be programmed to come out on P1.0. This pin, besides being a regular I/O pin, has two alternate functions. It can be programmed:

1. to input the external clock for Timer/Counter 2, or

2. to output a 50% duty cycle clock ranging from 61Hz to 4MHz at a

16MHz operating frequency.

To configure the Timer/Counter 2 as a clock generator, bit C/T2 (in T2CON) must be cleared and bit T20E in T2MOD must be set. Bit TR2 (T2CON.2) also must be set to start the timer.

The Clock-Out frequency depends on the oscillator frequency and the reload value of Timer 2 capture registers (RCAP2H, RCAP2L) as shown in this equation:

Oscillator Frequency

4 (65536 * RCAP2H,RCAP2L)

Where (RCAP2H,RCAP2L) = the content of RCAP2H and RCAP2L taken as a 16-bit unsigned integer.

In the Clock-Out mode Timer 2 roll-overs will not generate an interrupt. This is similar to when it is used as a baud-rate generator. It is possible to use Timer 2 as a baud-rate generator and a clock generator simultaneously. Note, however, that the baud-rate and the Clock-Out frequency will be the same.

Table 2. External Pin Status During Idle and Power-Down Mode

MODE PROGRAM MEMORY ALE PSEN PORT 0 PORT 1 PORT 2 PORT 3

Idle Internal 1 1 Data Data Data Data Idle External 1 1 Float Data Address Data Power-down Internal 0 0 Data Data Data Data Power-down External 0 0 Float Data Data Data

Philips Semiconductors Product specification

89C51/89C52/89C54/89C58

80C51 8-bit microcontroller family 4K/8K/16K/32K Flash

1999 Oct 27

TIMER 2 OPERA TION Timer 2

Timer 2 is a 16-bit Timer/Counter which can operate as either an event timer or an event counter, as selected by C/T

2* in the special function register T2CON (see Figure 1). Timer 2 has three operating modes: Capture, Auto-reload (up or down counting), and Baud Rate Generator, which are selected by bits in the T2CON as shown in Table 3.

Capture Mode

In the capture mode there are two options which are selected by bit EXEN2 in T2CON. If EXEN2=0, then timer 2 is a 16-bit timer or counter (as selected by C/T

2* in T2CON) which, upon overflowing sets bit TF2, the timer 2 overflow bit. This bit can be used to generate an interrupt (by enabling the Timer 2 interrupt bit in the IE register). If EXEN2= 1, Timer 2 operates as described above, but with the added feature that a 1- to -0 transition at external input T2EX causes the current value in the Timer 2 registers, TL2 and TH2, to be captured into registers RCAP2L and RCAP2H, respectively. In addition, the transition at T2EX causes bit EXF2 in T2CON to be set, and EXF2 like TF2 can generate an interrupt (which vectors to the same location as Timer 2 overflow interrupt. The Timer 2 interrupt service routine can interrogate TF2 and EXF2 to determine which event caused the interrupt). The capture mode is illustrated in Figure 2 (There is no reload value for TL2 and TH2 in this mode. Even when a capture event occurs from T2EX, the counter keeps on counting T2EX pin transitions or osc/12 pulses.).

Auto-Reload Mode (Up or Down Counter)

In the 16-bit auto-reload mode, Timer 2 can be configured (as either a timer or counter [C/T

2* in T2CON]) then programmed to count up or down. The counting direction is determined by bit DCEN (Down Counter Enable) which is located in the T2MOD register (see

Figure 3). When reset is applied the DCEN=0 which means Timer 2 will default to counting up. If DCEN bit is set, Timer 2 can count up or down depending on the value of the T2EX pin.

Figure 4 shows Timer 2 which will count up automatically since DCEN=0. In this mode there are two options selected by bit EXEN2 in T2CON register. If EXEN2=0, then T imer 2 counts up to 0FFFFH and sets the TF2 (Overflow Flag) bit upon overflow. This causes the Timer 2 registers to be reloaded with the 16-bit value in RCAP2L and RCAP2H. The values in RCAP2L and RCAP2H are preset by software means.

If EXEN2=1, then a 16-bit reload can be triggered either by an overflow or by a 1-to-0 transition at input T2EX. This transition also sets the EXF2 bit. The Timer 2 interrupt, if enabled, can be generated when either TF2 or EXF2 are 1.

In Figure 5 DCEN=1 which enables Timer 2 to count up or down. This mode allows pin T2EX to control the direction of count. When a logic 1 is applied at pin T2EX Timer 2 will count up. Timer 2 will overflow at 0FFFFH and set the TF2 flag, which can then generate an interrupt, if the interrupt is enabled. This timer overflow also causes the 16–bit value in RCAP2L and RCAP2H to be reloaded into the timer registers TL2 and TH2.

When a logic 0 is applied at pin T2EX this causes Timer 2 to count down. The timer will underflow when TL2 and TH2 become equal to the value stored in RCAP2L and RCAP2H. Timer 2 underflow sets the TF2 flag and causes 0FFFFH to be reloaded into the timer registers TL2 and TH2.

The external flag EXF2 toggles when Timer 2 underflows or overflows. This EXF2 bit can be used as a 17th bit of resolution if needed. The EXF2 flag does not generate an interrupt in this mode of operation.

(MSB) (LSB)

Symbol Position Name and Significance

TF2 T2CON.7 Timer 2 overflow flag set by a Timer 2 overflow and must be cleared by software. TF2 will not be set

when either RCLK or TCLK = 1.

EXF2 T2CON.6 Timer 2 external flag set when either a capture or reload is caused by a negative transition on T2EX and

EXEN2 = 1. When Timer 2 interrupt is enabled, EXF2 = 1 will cause the CPU to vector to the Timer 2 interrupt routine. EXF2 must be cleared by software. EXF2 does not cause an interrupt in up/down counter mode (DCEN = 1).

RCLK T2CON.5 Receive clock flag. When set, causes the serial port to use Timer 2 overflow pulses for its receive clock

in modes 1 and 3. RCLK = 0 causes Timer 1 overflow to be used for the receive clock.

TCLK T2CON.4 Transmit clock flag. When set, causes the serial port to use Timer 2 overflow pulses for its transmit clock

in modes 1 and 3. TCLK = 0 causes Timer 1 overflows to be used for the transmit clock.

EXEN2 T2CON.3 Timer 2 external enable flag. When set, allows a capture or reload to occur as a result of a negative

transition on T2EX if Timer 2 is not being used to clock the serial port. EXEN2 = 0 causes Timer 2 to

ignore events at T2EX. TR2 T2CON.2 Start/stop control for Timer 2. A logic 1 starts the timer. C/T2

T2CON.1 Timer or counter select. (Timer 2)

0 = Internal timer (OSC/12) 1 = External event counter (falling edge triggered).

CP/RL2

T2CON.0 Capture/Reload flag. When set, captures will occur on negative transitions at T2EX if EXEN2 = 1. When

cleared, auto-reloads will occur either with Timer 2 overflows or negative transitions at T2EX when

EXEN2 = 1. When either RCLK = 1 or TCLK = 1, this bit is ignored and the timer is forced to auto-reload

on Timer 2 overflow .

TF2 EXF2 RCLK TCLK EXEN2 TR2 C/T2

CP/RL2

SU00728

Figure 1. Timer/Counter 2 (T2CON) Control Register

Philips Semiconductors Product specification

89C51/89C52/89C54/89C58

80C51 8-bit microcontroller family 4K/8K/16K/32K Flash

1999 Oct 27

Table 3. Timer 2 Operating Modes

RCLK + TCLK CP/RL2 TR2 MODE

0 0 1 16-bit Auto-reload 0 1 1 16-bit Capture 1 X 1 Baud rate generator X X 0 (off)

OSC

÷ 12

C/T2

= 0

C/T2

= 1

TR2

Control

TL2

(8-bits)

TH2

(8-bits)

TF2

RCAP2L RCAP2H

EXEN2

Control

EXF2

Timer 2

Interrupt

T2EX Pin

Transition

Detector

T2 Pin

Capture

SU00066

Figure 2. Timer 2 in Capture Mode

Not Bit Addressable

Symbol Function

— Not implemented, reserved for future use.* T2OE Timer 2 Output Enable bit. DCEN Down Count Enable bit. When set, this allows Timer 2 to be configured as an up/down counter.

— — — — — — T2OE DCEN

SU00729

76543210

* User software should not write 1s to reserved bits. These bits may be used in future 8051 family products to invoke new features.

In that case, the reset or inactive value of the new bit will be 0, and its active value will be 1. The value read from a reserved bit is indeterminate.

Bit

T2MOD Address = 0C9H Reset Value = XXXX XX00B

Figure 3. Timer 2 Mode (T2MOD) Control Register

+ 22 hidden pages