Philips ne5532a, se5532a DATASHEETS

INTEGRATED CIRCUITS

NE/SA/SE5532/5532A

Internally-compensated dual low noise
operational amplifier

Product specification 1997 Sept 29
IC11 Data Handbook




Philips Semiconductors Product specification

Internally-compensated dual low noise
operational amplifier

DESCRIPTION

The 5532 is a dual high-performance low noise operational amplifier.
Compared to most of the standard operational amplifiers, such as
the 1458, it shows better noise performance, improved output drive
capability and considerably higher small-signal and power
bandwidths.

This makes the device especially suitable for application in
high-quality and professional audio equipment, instrumentation and
control circuits, and telephone channel amplifiers. The op amp is
internally compensated for gains equal to one. If very low noise is of
prime importance, it is recommended that the 5532A version be
used because it has guaranteed noise voltage specifications.

FEA TURES

•Small-signal bandwidth: 10MHz

•Output drive capability: 600Ω, 10V

•Input noise voltage:

5nV Hz

•DC voltage gain: 50000

•AC voltage gain: 2200 at 10kHz

•Power bandwidth: 140kHz

•Slew rate: 9V/µs

•Large supply voltage range: ±3 to ±20V

•Compensated for unity gain



RMS

(typical)

NE/SA/SE5532/5532A

PIN CONFIGURATIONS

FE, N, D8 Packages

OUTPUT A

INVERTING INPUT A

NON-INVERTING INPUT A

NOTE:

1. SOL and non-standard pinout.

1
2
3

V-

TOP VIEW

D Package

–IN

1

A

2

+IN

A

3

NC

4

–V

CC

5

NC

6

NC

7

+IN

B

8

–IN

B

TOP VIEW

Figure 1. Pin Configurations

8

V+

7

B

6
54

1

16
15
14
13
12
11
10

9

OUTPUT B
INVERTING INPUT B
NON-INVERTING INPUT B

NC
NC
NC
OUT

A

+V

CC

OUT

B

NC
NC

SL00332

A

ORDERING INFORMATION

DESCRIPTION TEMPERATURE RANGE ORDER CODE DWG #

8-Pin Plastic Dual In-Line Package (DIP) 0 to 70°C NE5532N SOT97-1
8-Pin Plastic Dual In-Line Package (DIP) –40°C to +85°C SA5532N SOT97-1
8-Pin Plastic Dual In-Line Package (DIP) –40°C to +85°C SA5532AN SOT97-1
8-Pin Ceramic Dual In-Line Package (CERDIP) 0 to 70°C NE5532FE 0580A
8-Pin Plastic Dual In-Line Package (DIP) 0 to 70°C NE5532AN SOT97-1
8-Pin Ceramic Dual In-Line Package (CERDIP) 0 to 70°C NE5532AF 0580A
8-Pin Ceramic Dual In-Line Package (CERDIP) -55°C to +125°C SE5532FE 0580A
8-Pin Ceramic Dual In-Line Package (CERDIP) -55°C to +125°C SE5532AF 0580A
8-Pin Small Outline Package (SO) 0 to 70°C NE5532AD8 SOT96-1
8-Pin Small Outline Package (SO) –40°C to 85°C SA5532D8 SOT96-1
8-Pin Small Outline Package (SO) –40°C to 85°C SA5532AD8 SOT96-1
8-Pin Small Outline Package (SO) -55°C to +125°C SE5532AD8 SOT96-1
8-Pin Small Outline Package (SO) 0 to 70°C NE5532D8 SOT96-1
8-Pin Small Outline Package (SO) –40°C to 85°C SA5532D8 SOT96-1
8-Pin Small Outline Package (SO) –40°C to 85°C SA5532AD8 SOT96-1
8-Pin Small Outline Package (SO) -55°C to +125°C SE5532D8 SOT96-1
16-Pin Plastic Small Outline Large (SOL) Package 0 to 70°C NE5532D SOT162-1
16-Pin Plastic Dual In-Line Package (DIP) -55°C to +125°C SE5532N SOT38-4

1997 Sept 29 853-0949 16639

2

Philips Semiconductors Product specification

Internally-compensated dual low noise
operational amplifier

EQUIVALENT SCHEMATIC (EACH AMPLIFIER)

+

_

NE/SA/SE5532/5532A

SL00333

Figure 2. Equivalent Schematic (Each Amplifier)

ABSOLUTE MAXIMUM RATINGS

SYMBOL PARAMETER RATING UNIT

V

S

V

IN

V

DIFF

T

A

T

STG

T

J

P

D

T

SOLD

NOTES:

1. Diodes protect the inputs against over-voltage. Therefore, unless current-limiting resistors are used, large currents will flow if the differential
input voltage exceeds 0.6V . Maximum current should be limited to ±10mA.

2. Thermal resistances of the above packages are as follows:

N package at 100°C/W
F package at 135°C/W
D package at 105°C/W
D8 package at 160°C/W

Supply voltage ±22 V
Input voltage ±V
Differential input voltage

1

SUPPLY

±0.5 V

Operating temperature range

SA5532/A –40 to +85 °C
NE5532/A 0 to 70 °C

SE5532/A -55 to +125 °C
Storage temperature -65 to +150 °C
Junction temperature 150 °C
Maximum power dissipation,

TA=25°C (still-air)

2

8 D8 package 780 mW
8 N package 1200 mW
8 FE package 1000 mW
16 D package 1200 mW

Lead soldering temperature (10sec max) 300 °C

V

1997 Sept 29

3

Philips Semiconductors Product specification

SYMBOL

PARAMETER

TEST CONDITIONS

UNIT

A

VOL

Large-signal voltage gain

V

OUT

Out ut swing

V

SYMBOL

PARAMETER

TEST CONDITIONS

UNIT

Internally-compensated dual low noise
operational amplifier

DC ELECTRICAL CHARACTERISTICS

TA=25°C VS=±15V, unless otherwise specified.

V

OS

∆VOS/∆T 5 5 µV/°C
I

OS

∆IOS/∆T 200 200 pA/°C
I

B

∆IB/∆T 5 5 nA/°C

I

CC

V

CM

CMRR Common-mode rejection ratio 80 100 70 100 dB
PSRR Power supply rejection ratio 10 50 10 100 µV/V

R

IN

I

SC

NOTES:

1. Diodes protect the inputs against overvoltage. Therefore, unless current-limiting resistors are used, large currents will flow if the differential
input voltage exceeds 0.6V . Maximum current should be limited to ±10mA.

2. For operation at elevated temperature, derate packages based on the package thermal resistance.

3. Output may be shorted to ground at V
not exceeded.

Offset voltage 0.5 2 0.5 4 mV

Offset current 100 10 150 nA

Input current 200 400 200 800 nA

Supply current

Common-mode input range ±12 ±13 ±12 ±13 V

-

p

Input resistance 30 300 30 300 kΩ
Output short circuit current 10 38 60 10 38 60 mA

1, 2, 3

SE/5532/5532A NE/SA/5532/5532A

Min Typ Max Min Typ Max

Over temperature 3 5 mV

Over temperature 200 200 nA

Over temperature 700 1000 nA

Over temperature 13 mA

RL≥2kΩ, VO=±10V 50 100 25 100 V/mV

Over temperature 25 15 V/mV

RL≥600Ω, VO=±10V 40 50 15 50 V/mV

Over temperature 20 10 V/mV

RL≥600Ω ±12 ±13 ±12 ±13

Over temperature ±10 ±12 ±10 ±12

RL≥600Ω, VS=±18V ±15 ±16 ±15 ±16

Over temperature ±12 ±14 ±12 ±14

RL≥2kΩ ±13 ±13.5 ±13 ±13.5

Over temperature ±12 ±12.5 ±10 ±12.5

=±15V, TA=25°C Temperature and/or supply voltages must be limited to ensure dissipation rating is

S

NE/SA/SE5532/5532A

8 10.5 8 16 mA

AC ELECTRICAL CHARACTERISTICS

TA=25°C VS=±15V, unless otherwise specified.

R

OUT

A

V

GBW Gain bandwidth product CL=100pF, RL=600Ω 10 MHz
SR Slew rate 9 V/µs

1997 Sept 29

NE/SA/SE5532/5532A

Min Typ Max

Output resistance

AV=30dB Closed-loop

f=10kHz, R

=600Ω

L

0.3 Ω

Voltage-follower

Overshoot VIN=100mV

P-P

10 %

CL=100pF, RL=600Ω

Gain f=10kHz 2.2 V/mV

V

=±10V 140 kHz

Power bandwidth V

OUT

=±14V, RL=600Ω, 100 kHz

OUT

VCC=±18V

4