Philips MCM398D Series Service Manual
CD Micro System
TABLE OF CONTENTS
3141 785 33420
DB 0907
2009
MCM302
Location of PC Boards ............................................. 1-1
Electronic Specification
............................................. 1-2
Measurement Setup ................................................ 1-3
Service Aids............................................................... 1-4
Software Version Check & Upgrade ........................ 2-1
Malfuction Check Chart ............................................. 2-2
Disassembly Diagram................................................ 3-1
Block Diagram ......................................................... 4-1
Wiring Diagram ......................................................... 4-2
Display Board ............................................................... 5
Circuit diagram ...................................................... 5-1
Layout diagram ...................................................... 5-2
Decoder Board ............................................................ 6
Circuit diagram ............................................. 6-1 to 6-3
Layout diagram ...................................................... 6-4
Power Board.................................................................. 7
Circuit diagram ...................................................... 7-1
Layout diagram ...................................................... 7-2
Exploded View .......................................................... 8-1
Service Partlist ......................................................... 9-1
Factory Partlist ...................................................... 10-1
Version 1.0
Location of PC Boards
1-1
VERSION VARIATIONS
:
Type /Versions:
Features
Board in used:
MCM302
Service policy
LCD DISPLAY BOARD
CD DECODER BOARD
POWER BOARD
* TIPS : C -- Component Level Repair.
M -- Module Level Repair
-- Used
/55
/55
/58
/58
/61
/61
/79
/79
/93
/93
/94
/94
/96
/96
/98
/98
/37
/37
/12
/12
/05
/05
Feature diffrence
RDS
TDS
VOLTAGE SELECTOR
ECO STANDBY - DARK
C
C
M
M
M
M
Type /Versions:
MCM302
Decoder Board
Power Board
Display Board
AMPLIFIER
Rated Output Power.........................25W x 2RMS
Signal-to-noise ratio...................................≥65dBA
Frequency response............. 60Hz~20KHz ±3.0db
Aux Input.................................0.5V RMS 20k ohm
DISC
LaserType.......................................Semiconductor
Disc Diameter.........................................12cm/8cm
Support Disc ...........................................................
CD-DA,CD-R,CD-RW,MP3
Audio DAC......................................24Bits/44.1kHz
Total Harmonic Distortion .................＜0.1%(1kHz)
Frequency Response .........................20Hz~20kHz
Signal to Noise Ratio .................................≥65dBA
TUNER
FM Tuning Range .............................87.5~108MHz
Tuning grid ...........................................100k/50kHz
Sensitivity
- Mono, 26db S/N Ratio ....................................5uV
– Stereo, 50dB S/N Ratio...............................100uV
Selectivity.......................................................>33dB
Image Rejection ............................................>25dB
Total Harmonic Distortion...................................3%
Signal to Noise Ration ................................≥65dBA
SPEAKERS
Speaker Impedance ................................................4ohm
Speaker Driver, base................................................4"
Speaker Driver,tweeter ............................................NA
Frequency Response ......................60Hz~20kHz ±3.0dbe
GENERAL INFORMATION
Total Output power ....................................... 50W RMS
AC Power.....................................................230V / 50Hz
Operation PowerConsumption ................................. 25W
Standby Power Consumption....................................<4W
Eco Standby Power Consumption.............................<1W
Headphone Output .................................2X15mV 32ohm
USB Direct......................................................Version 1.1
Dimensions
– Main unit (w x h x d)............................200x115x250mm
– Speaker box (w x h x d).......................150x250x165mm
– SUBwoofer(w x h x d)...............................................NA
Weight
–With Packing ...................................................6.75KG
–Main Unit ...........................................................2.55KG
–Speaker box ....................................................2X1.7KG
–SUBwoofer................................................................NA
Specifications and external appearance are
subject to change without notice.
1-2
Electronic Specification
1-3
LF Generator
e.g. PM5110
Recorder
Use Universal Test Cassette CrO2 SBC419 4822 397 30069
LEVEL METER
e.g. Sennheiser UPM550
with FF-filter
S/N and distortion met
e
e.g. Sound Technology ST170
L
R
DUT
or Universal Test Cassette
Fe SBC420 4822 397 30071
LEVEL METER
e.g. Sennheiser UPM550
-
S/N and distortion meter
e.g. Sound Technology ST1700B
L
R
DUT
CD
Use Audio Signal Disc
(replaces test disc 3)
SBC429 4822 397 30184
Bandpass
250Hz-15kHz
e.g. 7122 707 48001
LF Voltmeter
e.g. PM2534
DUT
S/N and distortion meter
e.g. Sound Technology ST1700B
Frame aerial
e.g. 7122 707 89001
Tuner AM (MW,LW)
To avoid atmospheric interference all AM-measurements have to be carried out in a Faraday´s cage.
Use a bandpass filter (or at least a high pass filter with 250Hz) to eliminate hum (50Hz, 100Hz).
RF Generator
e.g. PM5326
Ri=50:
Bandpass
250Hz-15kHz
e.g. 7122 707 48001
LF Voltmeter
e.g. PM2534
DUT
RF Generator
e.g. PM5326
S/N and distortion meter
e.g. Sound Technology ST1700B
Use a bandpass filter to eliminate hum (50Hz, 100Hz) and disturbance from the pilottone (19kHz, 38kHz).
Ri=50:
Tuner FM
MEASUREMENT SETUP
1-4
SERVICE AIDS
GB
WARNING
All ICs and many other semi-conductors are
susceptible to electrostatic discharges (ESD).
Careless handling during repair can reduce life
drastically.
When repairing, make sure that you are
connected with the same potential as the mass
of the set via a wrist wrap with resistance.
Keep components and tools also at this
potential.
ESD
CLASS 1
LASER PRODUCT
GB
Safety regulations require that the set be restored to its original
condition and that parts which are identical with those specified,
be used
Safety components are marked by the symbol
!
.
Lead free
Set remains closed!
N
Y
Play a CD
for at least 10 minutes
Y
playability
ok ?
N
playability
ok ?
add Info for customer
"SET OK"
check playability
N
Y
playability
ok ?
check playability
check playability
return set
Customer complaint
"CD related problem"
"fast" lens cleaning
1
2
3
For flap loaders (= access to CD drive possible)
cleaning method
4 is recommended
INSTRUCTIONS ON CD PLAYABILITY
1-
Exchange CDM
1 - 4 For description - see following pages
1
PLAYABILITY CHECK
For sets which are compatible with CD-RW discs
use CD-RW Printed Audio Disc ....................7104 099 96611
TR 3 (Fingerprint)
TR 8 (600μ Black dot) maximum at 01:00
• playback of these two tracks without audible disturbance
playing time for: Fingerprint t10seconds
Black dot from 00:50 to 01:10
• jump forward/backward (search) within a reasonable time
For all other sets
use CD-DA SBC 444A..................................4822 397 30245
TR 14 (600μ Black dot) maximum at 01:15
TR 19 (Fingerprint)
TR 10 (1000μ wedge)
• playback of all these tracks without audible disturbance
playing time for: 1000μ wedge t10seconds
Fingerprint t10seconds
Black dot from 01:05 to 01:25
• jump forward/backward (search) within a reasonable time
2
CUSTOMER INFORMATION
It is proposed to add an addendum sheet to the set which
informs the customer that the set has been checked
carefully - but no fault was found.
The problem was obviously caused by a scratched, dirty or
copy-protected CD. In case problems remain, the customer
is requested to contact the workshop directly.
The lens cleaning (method 3) should be mentioned in the
addendum sheet.
The final wording in national language as well as the printing
is under responsibility of the Regional Service Organizations.
4
LIQUID LENS CLEANING
Because the material of the lens is synthetic and coated
with a special anti-reflectivity layer, cleaning must be done
with a non-aggressive cleaning fluid. It is advised to use
“Cleaning Solvent
The actuator is a very precise mechanical component and
may not be damaged in order to guarantee its full function.
Clean the lens gently (don’t press too hard) with a soft and
clean cotton bud moistened with the special lens cleaner.
The direction of cleaning must be in the way as indicated in
the picture below.
Before touching the lens it is advised to clean the
surface of the lens by blowing clean air over it.
This to avoid that little particles make scratches on
the lens.
INSTRUCTIONS ON CD PLAYABILITY
1-
Loading...