Philips HR8707 Service Manual

Vision Vacuum cleaner

HR 8707

Service
Information

!

Philips Domestic Appliances and Personal Care

Service Manual

PRODUCT INFORMATION

- Maximum air displacement : 32 l/sec.

- Maximum vacuum water column : 280 cm

- Power consumption (IEC) 225V : 1400W

- Dust storage capacity : 4 litres

- Cord length (depends on version) : 6 metres

- Filter system : Paper dustbag
: Exhaust air fi lter
: Carbon inlet fi lter

- Dimensions cleaner : 48 x 30 x 25 cm

- Weight without accessories : 6.4 kg

- Noise : 75 dB

OPTIONAL

Exhaust air fi lter HR 6932 (8836 932 01210)
Oslo cotton dustbag HR 6935 (8836 935 01010)
Oslo paper dustbag set HR 6938 (8836 938 06110) economy
Oslo paper dustbag set HR 6938 (8836 938 10110) hygiene
Oslo 3-M dustbag HR 6938 (8836 938 91010)
Hard fl oor nozzle HR 6943 (8836 943 03010)
Dust sensor HR 6953 (4322 004 21250)
Turbo brush HR 6988 (8836 988 01010)

ADJUSTING THE PCB ON THE MOTOR TO 220V, 60HZ

1. Make sure that the potentiometer (item 58) is set at

min. position.

2. Adjust the potentiometer on the PCB (item 44) on the motor to
220V/60Hz. to allow the motor to run smootly.

Please note: * that the standard setting of the PCB is 230V, 50Hz.
* that there are open-circuit voltages on all wires.

SERVICE INFORMATION

- To open the appliance, fi rst remove the panel (item 13) with a big
screw driver (V) to disconnect the 4 snap locks (the 4 screws of
button panel item 39 can be loosed) and then remove the two
pedals (items 1 and 14) with a pin (W), max. diameter 2.5 mm.

- Power meter (8838 000 60300) is a commercial item with a fi xed
air displacement which measures the vacuum of the appliance.

- Component confi guration on exploded view may differ in case
of specifi c versions. However, the actual components are
distinguished by means of code numbers.

- If a repair has been made, make sure that all functions of the
appliance are working correctly.

- The spare parts have been standarized as much as possible.

- Item 7A. This appliance is provided with ring 7A. For other parts
use item 6 or 7.

- Item 16 Cotton dustbag is used in those countries where paper
dustbags are not available.

- Item 21 is provided with the long cord-winder spring; both long
and short cords can be used in combination with this spring.

- To disassemble the cordwinder use TORX screw driver no T15,
which is one of a set consisting of T20, T15, T10, T9, T8, T7 and
T6 = 4822 395 50145.

- Item 34. Remove the control lever.

- Depending on the original cord, the spare cord must be shortened
from 8.5 into 6 metres.

- Item 43 air valve opens to cool the motor if the air displacement is
too low or if the air fl ow is blocked.

This product meets the requirements regard­ing interference suppression on radio and TV.

After the product has been repaired, it should
function properly and has to meet the safety
requirements as offi cially laid down at this
moment.

Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification

4322 277 00208
00/02

PCS 101 346

1 4322 003 11230 cord-winder pedal
2 4322 003 11150 accessory cover red
3 4322 009 07090 acc. cover spring
5 4322 005 06650 acc. cover lock
6 4322 001 72800 diaphragm valve

7 4322 009 06420 swivel connector
7A 4322 003 15820 ring
8 4322 001 71960 sealing rubber
9 4322 003 11270 dust cover red
10 4322 000 03800 dust-cover spring

11 4322 003 11310 dust-cover snaplock red
12 4322 003 10630 cord-winder lever
13 4322 009 07370 version panel red
14 4322 003 11350 switch pedal red
16 8836 938 10110 oslo paper dustbag hyg.

8836 935 01010 oslo cotton dustbag (opt.)
8836 938 91010 oslo 3M-dustbag (opt.)
18 4322 009 06410 dustbag holder
20 4322 009 07280 dust chamber
21 4322 009 05350 reel half spring unit

22 4322 003 10470 connection piece
23 4322 001 72360 brake tyre
24 4322 009 04800 reel half contact unit
25 4322 009 05060 contact-ring plate
26 4322 007 11960 cordset Australia L = 6.3 m

2

27 4322 007 12150 cordset Japan (2 x 1.25 mm
4322 006 01620 cordset (2 x 0.75 mm

)

2

)
28 4322 007 12190 cordset UK L = 6.3 m
29 4322 007 11930 cordset L = 6.3 m 4.8 mm pins
4322 007 11920 cordset L = 8.3 m 4.8 mm pins (opt.)

30 4322 007 12020 cordset Swiss L = 6.3 m
31 4322 007 11950 cordset Italy L = 6.3 m
32 4322 003 10420 lower housing
33 4322 005 04700 caster assy
35 4322 000 03790 button spring

36 4322 001 98860 switch lever
37 4322 005 04750 parking hook
38 4322 006 50580 main switch
39 4322 003 11190 button panel
40 4322 003 10590 upper housing

41 8836 949 01010 act. carbon fi lter
4322 000 37300 safety fi lter Trio (opt.)
42 4322 003 10950 grill act. carbon fi lter
4322 009 07040 safety fi lter + grille (opt.)

43 4322 005 04730 air inlet valve 220-240V
44 4322 006 20720 power module dt 230V
45 4322 003 10430 rear wheel
46 4322 003 11580 rear wheel cap
47 4322 003 10570 cord outlet

48 4322 003 10580 back grille
4322 003 16990 S-fi lter grille (opt.)
49 8836 932 01210 AFS fi lter
8836 992 01010 S-fi lter (opt.)
50 4322 009 06400 motor housing

52 4322 001 72790 back motor buffer
53 4322 003 09720 suspension bracket
54 4322 000 03700 PCB mounting spring
55 4322 009 06430 motor 1441 - 230V
56 4322 001 72780 front motor buffer

57 4322 003 09820 motor disc
58 4322 006 20760 potentiometer 220-240V
61 4822 528 11128 coupling piece conical
62 4822 358 10205 drive belt
63 4822 479 20201 brush assy

64 8836 988 01010 turbo nozzle complete (conical)
120 4322 009 05400 metal-tube clip (opt.)
121 4322 002 22610 metal-tube (opt.)
122 4322 009 05410 telesc. -tube clip
123 4322 004 21050 telescopic tube

124 4322 003 16000 cat and dog brush
125 4322 004 27440 eco bend + hose
126 4322 005 03770 eco bend
127 4322 004 22110 nozzle RD 255
129 4322 003 07620 crevice nozzle

130 4322 004 21160 small nozzle
131 4322 004 21170 brush nozzle

DFU 4222 000 46850 West Europe total

West Europe

English Norwegian

German Danish
French Swedish

Dutch Finnish

Portuguese Turkey

Spanish Greec

Italian

M

CONNECTOR

MOTOR
POWER

MODULE

MAIN SWITCH

MAX

MIN

CORD WINDER

W

V

V

W