Philips HR8573AC Service Manual

Mobilo Vacuum cleaner

HR8573
/A
/C

Philips Domestic Appliances and Personal Care

Service Manual

PRODUCT INFORMATION

- This product meets the requirements regarding
interference suppression on radio and TV.

- After the product has been repaired, it should function
properly and has to meet the safety requirements as
officially laid down at this moment.

TECHNICAL INFORMATION

- Colour /A : Green
/C : Lemonade

- Maximum air displacement : 37 l/sec.

- Maximum vacuum water column : 310 cm

- Power consumption (IEC) : 1400 W

- Dust storage capacity : 3 litres

- Cord length : 6.3 metres

- Filter system : Paper dustbag
: Motor inlet filter
: Exhaust air filter

- Dimensions cleaner : 44.5 x 29.5 x 25 cm

- Weight cleaner : 5.5 kg

- Noise : 77 dB

OPTIONAL (accessories)

Exhaust air fi lter FC8032 (4822 015 70056)
Active carbon fi lter FC8033 (8838 033 01010)
Active carbon fi lter replacem. set FC8034 (items 12 + 13)
S-class fi lter FC8044 (8838 044 01010)
S-class fi lter replacement set HR6994 (items 19 + 20)
Sydney cotton dustbag HR6997 (4822 480 10115)
Sydney closable pap. dustbag FC8021 (8838 021 00000)
Sydney 3-M dustbag FC8022 (8838 022 01010)
Turbo brush FC8043 (4322 004 22960)

= changed

Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification

04/03

HR8573 /A /C

DISASSEMBLY- AND RE-ASSEMBLY ADVISE

- To open the appliance, first remove the 2 screws of the

control panel (item 11) then with a big screw driver
disconnect the 2 snap locks of panel and lower housing
(see drawing).

- The component configuration shown in the exploded view
may differ in case of specific versions. The components are
distinguished by means of code numbers.

- When the repair is finished, check whether all functions of
the appliance work properly.

- To (dis)assemble the appliance use TORX screw driver no
T15 (4822 395 10329), which is one of a set consisting of
T20, T15, TI0, T9, T8, T7 and T6 = 4822 395 50145.

REPAIR INSTRUCTION

- The infrared remote control can adjust the suction power
with 5 speeds. When switched on, the appliance always
starts with the highest power, even without a connected
hose. Use LR03 batteries. Alkaline is advised.

- The spare parts have been standardized as much as possible.

- Item 6, cotton dustbag, is used in those countries where
paper dustbags are not available.

- The cordwinder is provided with a long cord-winder spring;
both long and short cords can be used in combination with
this spring.

- The cord winder spring must be tensioned to the maximum
level and then be rewound approx. 1.5 turn.

- Depending on the original cord, the spare cord must be
shortened to the length of the original cord.

- If the cord comes without AMP clamps, it can be soldered
onto the terminals.

- If the reel half spring unit is replaced, shaft A must be
lubricated with silicone grease (A). Do not apply any
silicone grease to or spill any grease on the terminals or
conductors.

- Adjusting the PCB on the motor to 220V, 60Hz.

1. Make sure that the potentiometer (item 36) is set at

min. position.

2. Adjust the potentiometer on the PCB item 45, on the

motor to 220V/60Hz to allow the motor to run
smoothly.

Please note: the standard setting of the spare PCB is

230V/50Hz.
There are open-circuit voltages on all wires.

M

PMT

MOTOR
POWER

MODULE

MAIN

SWITCH

CORD WINDER

IR-RECEIVER

+

CONTROL

IR

IR-TRANSMITTER

2-7

PARTS LIST

HR8573 /A /C

Pos Service code Description Version

1

4322 003 16870

4322 003 14850

2

4322 000 67680

3

4322 009 07390

4322 009 07140

4

4322 001 94690

5

4322 003 16900

4322 003 14900

6

8838 021 00000
8838 022 01010

4822 480 10115

7

4322 009 06760

8

4322 003 12280

9

4322 003 12020

10

4322 005 08650

11

4322 005 15120

4322 003 14890

12

4322 009 07040
4322 003 10950

13

4322 000 37300

8838 033 01010

14

4322 005 11490

4322 003 14860

15

4322 001 72780

16

4322 003 12080

17

4322 003 16770

18

4322 009 07400

19

8838 044 01010
4822 015 70056

20

4322 005 08660

4322 003 16950

21

4322 009 07940

23

4322 001 72360

24

4322 009 07950

25

4322 009 07960

26

4322 006 01440
4322 006 01760

Acc. cover Green /A
Acc. cover Lemonade /C
Dust indicator spring
Dust cover Green /A
Dust cover Lemonade /C

Packing ring
Front cover Green /A
Front cover Lemonade /C
Sydney closable pap. dustbag (opt.)
Sydney 3M dustbag

Sydney cotton dustbag (opt.)
Dustbag carrier
Clamp of dustbag carrier
Dust compartment sealing
Lens

Back panel stamped Green /A
Back panel stamped Lemonade /C
Inletgrill + trio fi lter
Active carbon fi lter grill (opt.)
Trio fi lter

Active carbon fi lter (opt.)
Pedal Green /A
Pedal Lemonade /C
Buffering motor
Motor disc

Cord outlet
Lower housing + wheels
S-class fi lter (opt.)
AFS micro fi lter
Grill S-class fi lter (opt.)

Grill AFS micro fi lter
Reel half spring unit (l=9m)
Brake tyre
Reel half contact unit
Contact ring plate

Cord set Argentina L= 9.3 m
Cord set Australia L= 9.3 m

Pos Service code Description Version

27

4322 006 01680

28

4322 006 01720

29

4322 006 01410

30

4322 006 01670

31

4322 006 01460

32

4322 003 12240

33

4322 005 08700

35

4322 009 07410

36

4322 006 22370

37

4322 003 12030

41

4322 006 50580

42

4322 003 12010

43

4322 001 72790

44

4322 003 09720

45

4322 006 22460

46

4322 000 03700

47

4322 009 06430

48

4322 000 09750

73

4322 006 22600

73a

4322 003 19420

74

4322 007 16000

75

4322 005 13510

76

4322 003 18860

77

4322 003 22030

78

4322 004 22560

81

4322 004 22570

103

4322 003 20730

104

4322 004 22510

105

4322 004 22490

114

4322 004 22960

115

9965 000 03349

116

4822 358 10205

117

4822 479 20201

121

4322 001 99120

122

4322 007 45550

A

5322 390 20011

B

4322 002 82550

Cord set Taiwan L= 6.3 m
Cord set U.K. / H.K. L= 9.3 m
Cord set Euro 4.8mm pins L= 9.3 m
Cord set Swiss L= 9.3 m
Cord set Italy L= 9.3 m

Dustbag sealing
Caster assy standard
Rear wheel + cover
Speed control IR-receiver
Cord winder lever

Push button switch
Motor cover
Rear motor buffer
Suspension bracket
Motor print 230 V - 50 Hz / RMC

PCB clamp
Motor 220-240 V / 50-60 Hz
Spring switch knob
IR-RMC send unit
Cover batt. comp.

Leafspring
Hose and standard bend
Bend RMC
Crevice nozzle 118 mm
Small nozzle

Plumeau
Tube clip assy 35 mm
Telesc. tube + clamp
Nozzle R & C
Turbo nozzle FC8043 (opt.)

Coupling piece
Drive belt
Brush assy
Coupling bush
Coupling spring

Silicon grease for the shaft
Screw 3.5 x 12 / T10

= changed

3-7