Philips HR8573 Service Manual

Mobilo Vacuum cleaner

HR 8573

Philips Domestic Appliances and Personal Care

Service Manual

PRODUCT INFORMATION

- Maximum air displacement : 37 l/sec.

- Maximum vacuum water column : 310 cm

- Power consumption (IEC) : 1400 W

- Dust storage capacity : 3 litres

- Cord length : 6.3 metres

- Filter system : Paper dustbag
: Motor inlet fi lter
: Exhaust air fi lter

- Dimensions cleaner : 44.5 x 29.5 x 25 cm

- Weight cleaner : 5.5 kg

- Colour cleaner : Green

- Noise : 77 dB

OPTIONAL

Exhaust air fi lter FC 8032 (4822 015 70056)
Active carbon fi lter FC 8033 (8838 033 01010)
Active carbon fi lter replacem. set FC 8034 (items 12 + 13)
S-class fi lter FC 8044 (8838 044 01010)
S-class fi lter replacement set HR 6994 (items 19 + 20)
Sydney cotton dustbag HR 6997 (4822 480 10115)
Sydney closable pap. dustbag FC 8021 (8838 021 00000)
Sydney 3-M dustbag FC 8022 (8838 022 01010)
Turbo brush FC 8043 (4322 004 22960)

SERVICE INFORMATION

- The infrared remote control can adjust the suction power with 5
speeds. When switched on, the appliance always starts with the
highest power, even without a connected hose.

Use LR03 batteries. Alkaline is advised.

- Component confi guration on exploded view may differ in case
of specifi c versions. However, the actual components are distin­guished bij means of code numbers.

- The spare parts have been standardized as much as possible.

- Item 6, cotton dustbag, is used in those countries where paper
dustbags are not available.

- Item 21 is provided with a long cord-winder spring; both long and
short cords can be used in combination with this spring.

- Cordwinder spring has to be tensioned till maximum minus
approx. 1,5 revolution.

- Depending on the original length of the cord, the spare cord must
be shortened.

- If pos. 21 is replaced, shaf A must be lubricated with silicone
grease (A). This grease may not be used on terminals (25) or on
conductors (24).

- To (dis)assemble the appliance use TORX screw driver no T15
= 4822 395 10329, which is one of a set consisting of T20, T15,
TI0, T9, T8, T7 and T6 = 4822 395 50145.

- Adjusting the PCB on the motor to 220V, 60Hz.

1. Make sure that the potentiometer (item 36) is set at min.

position.

2. Adjust the potentiometer on the PCB item 45, on the motor to

220V/60Hz to allow the motor to run smoothly.

Please note: the standard setting of the spare PCB is

230V/50Hz.
There are open-circuit voltages on all wires.

This product meets the requirements regard­ing interference suppression on radio and TV.

After the product has been repaired, it should
function properly and has to meet the safety
requirements as offi cially laid down at this
moment.

Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification

4322 277 00995
02/07

Pos. 12 nc description

1 4322 003 16870 acc. cover Green
2 4322 000 67680 dust indicator spring
3 4322 009 07390 dust cover brown Green
4 4322 001 94690 packing ring
5 4322 003 16900 front cover Green

6 8838 021 00000 Sydney closable pap. dustbags (opt.)
8838 022 01010 Sydney 3M dustbag
4822 480 10115 Sydney cotton dustbag (opt.)
7 4322 009 06760 dustbag carrier
8 4322 003 12280 clamp of dustbag carrier

9 4322 003 12020 dust compartment sealing
10 4322 005 08650 lens
11 4322 005 15120 back panel stamped Green
12 4322 009 07040 inletgrill + trio fi lter
4322 003 10950 active carbon fi lter grill (opt.)

13 4322 000 37300 trio fi lter
8838 033 01010 active carbon fi lter (opt.)
14 4322 005 11490 pedal Green
15 4322 001 72780 buffering motor
16 4322 003 12080 motor disc

17 4322 003 16770 cord outlet
18 4322 009 07400 lower housing + wheels
19 8838 044 01010 S-class fi lter (opt.)
4822 015 70056 AFS micro fi lter
20 4322 005 08660 grill S-class fi lter (opt.)

4322 003 16950 grill AFS micro fi lter
21 4322 009 07940 reel half spring unit (l=9m)
23 4322 001 72360 brake tyre
24 4322 009 07950 reel half contact unit
25 4322 009 07960 contact ring plate

26 4322 006 01440 Cord set Argentina L= 9.3 m
4322 006 01760 Cord set ustralia L= 9.3 m
27 4322 006 01680 Cord set Taiwan L= 6.3 m
28 4322 006 01720 Cord set U.K. / H.K. L= 9.3 m
29 4322 006 01410 Cord set Euro 4.8mm pins L= 9.3 m

Pos. 12 nc description

30 4322 006 01670 Cord set Swiss L= 9.3 m
31 4322 006 01460 Cord set Italy L= 9.3 m
32 4322 003 12240 dustbag sealing
33 4322 005 08700 caster assy standard
35 4322 009 07410 rear wheel + cover

36 4322 006 22370 speed control IR-receiver
37 4322 003 12030 cord winder lever
41 4322 006 50580 push button switch
42 4322 003 12010 motor cover
43 4322 001 72790 rear motor buffer

44 4322 003 09720 suspension bracket
45 4322 006 22460 motor print 230 V - 50 Hz / RMC
46 4322 000 03700 PCB clamp
47 4322 009 06430 motor 220-240 V / 50-60 Hz
48 4322 000 09750 spring switch knob

73 4322 006 22600 IR-RMC send unit
73A 4322 003 19420 cover batt. comp.
74 4322 007 16000 leafspring
75 4322 005 13510 hose and standard bend
76 4322 003 18860 bend RMC

77 4322 003 22030 crevice nozzle 118 mm
78 4322 004 22560 small nozzle
81 4322 004 22570 plumeau
103 4322 003 20730 Tube clip assy 35 mm
104 4322 004 22510 Telesc. tube + clamp

105 4322 004 22490 Nozzle R & C
114 4322 004 22960 Turbo nozzle FC 8043 (opt.)
115 9965 000 03349 Coupling piece
116 4822 358 10205 Drive belt
117 4822 479 20201 Brush assy

121 4322 001 99120 Coupling bush
122 4322 007 45550 Coupling spring

A 5322 390 20011 silicon grease for the shaft
B 4322 002 82550 screw 3.5 x 12 / T10

M

PMT

MOTOR
POWER

MODULE

MAIN

SWITCH

CORD WINDER

IR-RECEIVER

+

CONTROL

- To open the appliance, fi rst remove the 2 screws of the
control panel (item 11) then with a big screw driver dis­connect the 2 snap locks of panel and lower housing
(see drawing).

IR

IR-TRANSMITTER