Philips HR8572AD Service Manual

Mobilo Vacuum cleaner

HR8572
/A
/D

Philips Domestic Appliances and Personal Care

Service Manual

PRODUCT INFORMATION

- This product meets the requirements regarding
interference suppression on radio and TV.

- After the product has been repaired, it should function
properly and has to meet the safety requirements as
officially laid down at this moment.

TECHNICAL INFORMATION

- Colour /A : Red
/D : Blue berry purple

- Maximum air displacement : 32 l/sec.

- Maximum vacuum water column : 240 cm

- Power consumption (IEC) : 1200 W

- Duststorage capacity : 3 litres

- Cord length (depends on version) : 6 metres

- Filter system : Paper dustbag
: Motor inlet filter
: Exhaust air filter

- Dimensions cleaner : 445 x 295 x 250 mm

- Weight cleaner : 5.5 kg

OPTIONAL (accessories)

Exhaust air filter FC8032 = 4822 015 70056
Active carbon filter FC8033 = 4822 480 20145
Active carbon filter replacem. set FC8034 = item 12 + 13
S-class filter FC8044 = 8838 044 01010
S-class filter replacement set HR6994 = item 19 + 20
Sydney cotton dustbag HR6997 = 4822 480 10115
Sydney closable paper dustbag FC8021 = 8838 021 00000
Turbo brush FC8043 = 4822 479 20196

= changed

Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification

03/10

HR8572 /A /D

DISASSEMBLY- AND RE-ASSEMBLY ADVISE

- To open the appliance, first remove the 2 screws of the

control panel (item 11) then with a big screw driver
disconnect the 2 snap locks of panel and lower housing
(see drawing).

- The component configuration shown in the exploded view
may differ in case of specific versions. The components are
distinguished by means of code numbers.

- When the repair is finished, check whether all functions of
the appliance work properly.

- To (dis)assemble the appliance use TORX screw driver no
T15 (4822 395 10329), which is one of a set consisting of
T20, T15, TI0, T9, T8, T7 and T6 = 4822 395 50145.

- To connect the nozzle, the telescopic tube and the handle:
insert the narrowed section into the wider section while
turning it a little.
To disconnect: Pull while rotating. To adjust the telescopic
tube (item 74) to the required length, use the knob in the
direction of the arrow while sliding the top section of the
telescopic tube into or out of the lower section.

REPAIR INSTRUCTION

- The spare parts have been standardized as much as possible.

- Item 6, cotton dustbag, is used in those countries where

paper dustbags are not available.

- The cordwinder (item 21) is provided with a long cord-

winder spring; both long and short cords can be used in
combination with this spring.

- The cord winder spring must be tensioned to the maximum
level and then be rewound approx. 1.5 turn.

- Depending on the original cord, the spare cord must be
shortened to the length of the original cord.

- If the cord comes without AMP clamps, it can be soldered
onto the terminals.

- If the reel half spring unit is replaced, shaft A must be
lubricated with silicone grease (A). Do not apply any
silicone grease to or spill any grease on the terminals or
conductors.

- The assembly of accessories depends on the national
version.

- Adjusting the PCB on the motor to 220V, 60Hz.

1. Make sure that the potentiometer (item 36) is set at

min. position.

2. Adjust the potentiometer on the PCB item 45, on the

motor to 220V/60Hz to allow the motor to run
smoothly.

Please note: the standard setting of the spare PCB is

230V/50Hz.
There are open-circuit voltages on all wires.

M

MOTOR
POWER

MODULE

MAIN

SWITCH

CORD WINDER

ROTARY
POTMETER

2-7

PARTS LIST

HR8572 /A /D

Pos Service code Description Version

1

4322 005 14870

4322 003 14530

2

4822 492 11408

3

4322 009 08700

4322 009 09130

4

4822 532 60926

5

4322 003 19220

4322 003 13460

6

8838 021 00000
4822 480 10115

7

4822 256 10354

8

4822 401 11689

9

4822 466 11497

10

4322 005 14860

4322 005 10980

11

4322 003 19250

4322 003 13440

12

4822 458 10649
4822 458 10461

13

4822 480 10228

4822 480 20145

14

4322 003 19260

4322 003 14570

15

4822 466 62655

16

4822 466 11487

17

4322 003 12510

18

4822 441 12341

19

4822 015 70056

8838 044 01010

20

4322 009 06910

4322 005 15970

21

4322 009 07940

23

4322 001 72360

24

4322 009 07950

25

4322 009 07960

Acc. cover /A
Acc. cover /D
Dust indicator spring
Dust panel /A
Dust panel /D

Packing ring
Front cover /A
Front cover /D
Sydney closable pap. dustbag
Sydney cotton dustbag (opt.)

Dustbag carrier
Clamp of dustbag carrier
Dust compartment sealing
Turn knob /A
Turn knob /D

Back panel /A
Back panel /D
Inletgrill + trio fi lter
Active carbon fi lter grill (opt.)
Trio fi lter

Active carbon fi lter (opt.)
Pedal /A
Pedal /D
Bufferring motor
Motor disc

Cord out let
Lower housing + wheels
Exhaust air fi lter
S-fi lter /D
Air outlet grill

S-fi lter grill /D
Reel half spring unit (L=9m)
Brake tyre
Reel half contact unit
Contact ring plate

Pos Service code Description Version

26

4322 006 01440
4322 006 01760

27

4322 006 01680

28

4322 006 01720

29

4322 006 01400

30

4322 006 02080

31

4322 006 01460

32

4822 532 12782

33

4822 528 11334

35

4322 009 06710

36

4822 214 12224

37

4822 479 20197

41

4822 276 13205

42

4822 462 10911

43

4822 466 10765

44

4822 402 10109

45

4822 214 11359

46

4822 492 11011

47

4822 361 10768

48

4822 492 11407

71

4822 492 71622

72

4822 530 10229

73

4322 003 20730

74

4322 004 22990

75

4822 530 10382

76

4822 530 10235

77

4822 479 20195

78

4822 479 60118

79

4822 479 70072

80

4822 479 20123

81

4822 479 30176

85

4822 479 20196

A

5322 390 20011

B

4322 002 82550

Cord set Argentina L=9.3 m
Cord set Australia L=9.3 m
Cord set Taiwan L=6.3 m
Cord set U.K. / H.K. L=9.3 m
Cord set Euro 4.8mm pins L=6.3 m

Cord set Swiss L=6.3 m
Cord set Italy L=9.3 m
Dustbag sealing
Caster
Rearwheel (standard)

Speed control 220-240V
Cord winder lever
Push button switch
Motor cover
Rear motor buffer

Suspension bracket
Motor power PCB 230V-50Hz
PCB clamp
Motor 220-240V/50-60Hz
Spring switch-knob

Clip metal tube (opt.)
Metal tube (opt.)
Clip telescopic tube
Telescopic tube
Bend + hose ass’y

Bend ass’y
Crevice nozzle
Small nozzle
Big nozzle
Strip of big nozzle

Plumeau

Turbo brush complete

Silicon grease for the shaft
Screw 3.5 x 12 / T10

= changed

3-7