Philips HR7724-16, HR7723-00 Service Manual

Cucina Food processor

HR7723/00 HR7724/16

Philips Domestic Appliances and Personal Care

Service Manual

PRODUCT INFORMATION

- The food processors are equipped with mechanical and thermal safety switches.

- Product meets the requirements regarding interference suppression on radio and TV.

- After the product has been repaired, it should function properly and has to meet the safety requirements as laid down ofﬁ cially established at this moment.

Automatic resettable cut-out (part of item 7)

- To prevent damage due to overheating, the appliance has been equipped with an automatic cut-out system. This system will automatically cut off the power supply when the appliance overheats. If the appliance suddenly stops running:

- Unplug the appliance

- Set the knob to position 0

- Let the appliance cool down for 15 minutes

- Plug the appliance in again

- Switch the appliance on again

Safety lock (item 1)

- Place the lid on the bowl in the right position. The appliance will only function if the arrow on the applinace is directly opposite the mark on the lid of the food processor bowl and the same holds for the other accessoires. The built-in safety lock will now be deblocked and you can turn the appliance on. Note that if both the blender jar and the bowl have been correctly mounted, only the blender will function.

TECHNICAL INFORMATION

- Motor power : HR7723 - 600 W HR7724 - 700 W

- Voltage : 230 V : 110 V

- Frequency : 50 / 60 Hz

- Colour : White

- Cordset : 125 cm

- Speed settings : 2 speeds + pulse

- Bowl capacity : 2.5 l dry ingredients

1.0 l liquids

- Blender capacity : 1.0 l liquids

2.0 l (max. contents)

- Speeds unloaded : blender drive shaft 17000 rpm (max) acc. drive shaft 2150 rpm (max) acc. drive shaft 1400 rpm (min)

- Weight in fancy box : HR7723/24 - 5100 g

- Dimensions : HR7723/24 - 420 x 280 x 360 (l x w x h)

- SAP coding : HR7723/00 HR7724/16

Important:

- If the appliance is used without the blender jar, the appliance will not function if the screw cap has not been screwed onto the attaching hole for the blender.

Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification

4322 277 01090 02/11

DISASSEMBLY- AND RE-ASSEMBLY ADVISE

- A separate drawing shows how to disconnect the speed selection knob.

- The blender coupling on the motor shaft has been provided with the customary left-hand thread. The drive coupling (item 11) can be detached by means of a hammer and a screwdriver. Strike the screwdriver with a short sharp blow and remove the drive coupling. Or block the acc. drive wheel (item 23) and thereby the rotor shaft, by sticking a pin through the hole (5 mm dia.) in the bottom plate.

HR7723/00 / HR7724/16

- The top housing (item 29) can be removed by detaching the snap connections by sticking a pin (or a screwdriver) through the small round holes (3 mm dia.) in the bottom plate (item 27) and the housing (item 12). The arrows in the drawing show the locations of the holes.

- In order to replace the speed selection knob, the locking lever (item 33) must be placed in its lowest position.

- The accessory drive shaft (item 15) has a locking piece (item 14).

- The assembly of the accessories depends on the national version.

- For speciﬁ c versions, the component conﬁ guration may differ from the one shown on the exploded view. However, the actual components can be distinguished by their code numbers.

- Make sure that all functions, including the safety devices, are working correctly after you have completed the repair.

REPAIR INSTRUCTION

- No speciﬁ c issues

OPTIONAL (ACCESSORIES)

- No speciﬁ c issues

brown

MAINS

blueRN

470k

PARTS LIST

Pos Service code Description

4203 065 62110

4822 214 12762

4203 065 62120

4822 532 13008

4822 462 11074

4822 361 11081

4822 361 11082 4822 466 11949

4203 065 60300

4822 502 14593

4203 065 62130

4203 065 64570

4822 214 12767

4822 402 11076

4822 535 10548

4203 065 62070

4822 466 11948

4822 535 10549

4822 530 10492

4822 492 11649

Print + switch lever Print plate brake Coupling lever Rubber piece Air tunnel

Motor 230 V Motor 110 V Coupling fork Flex Motor screw assy

Blender coupling Housing Print plate Locking piece Drive spindle

Rubber sealing Locking plate Spindle assy Rubber tube Compression spring

Speed High

and Pulse

Speed Low

HR7723 / HR7724

D1 1N5406

red

brown

blackF1F2

violet N

Change-over switch

in braking position

white

Rotor

yellow

Pos Service code Description

4822 528 11265

4822 358 10257

4822 528 11266

4822 520 10851

4822 466 11947

4203 065 64610

4203 065 64620

4203 065 64630

4203 065 64640 4822 492 11648

4203 065 64600

4203 065 62180 4203 065 62200

Coupling piece Tooth belt Belt wheel Bearing Mounting plate

Bottom plate Blender cover Housing top HR7723 Housing top HR7724 Snap return spring

Switch knob HR7723 Switch knob HR7724 Locking lever

2-4

+ 2 hidden pages