Philips HD7810/65 User Manual

HD7810

2345678

9101112131415161718192021

4222.200.0728.3 (8/19/2019)

>75 % recycled paper >75 % papier recyclé

English

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed including the following:

1 Read all instructions. 2 Do not touch hot surfaces. Use handles or knobs. 3 To protect against electrical shock, do not immerse cords,

plugs, or appliance in water or other liquid.

4 Close supervision is necessary when any appliance is used by

or near children.

5 Unplug from outlet when not in use and before cleaning. Allow

to cool before you putting on or taking off parts and before cleaning the appliance.

6 Do not operate any appliance with a damaged cord or plug or

after the appliance malfunctions, or has been damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or adjustment.

7 For assistance, call 1-866-4 Senseo (1-866-473-6736) or visit

our website at www.senseo.us.

8 The use of accessory attachments not recommended by the

appliance manufacturer may result in fire, electric shock or

injury to persons. 9 Do not use outdoors. 10 Do not let cord hang over edge of table or counter or touch

hot surfaces. 11 Do not place on or near a hot gas or electric burner, or in

heated oven. 12 Extreme caution must be used when moving an appliance

containing hot liquids. 13 To disconnect, turn off by pressing the power button and then

remove plug from wall outlet. 14 Do not use the appliance for other than intended use. 15 This appliance is intended for household use ONLY. It is not

intended for commercial or industrial use. 16 To remove the plug, grip plug body and pull it from the outlet. 17 Never yank or twist cord to unplug. 18 Do not use this coffee machine if its lid has a cracked, loose,

weakened, or damaged lever. 19 The machine does not work at temperatures below 50°F

(10°C). 20Do not use the machine at altitudes higher than 6800ft.

(2200m) above sea level. 21 Flush the coffee machine with fresh water before you use it for

the first time (see chapter ‘Preparing the machine for use’).

This causes the system to fill with water, which is essential for

the machine to work properly. 22 Operate the coffee machine on a flat, stable surface away

from the edge of the counter to avoid accidental tipping. 23 To prevent scalds and/or property damage, always make sure

the coffee machine lid is securely locked before or during a

brewing cycle. Do not use force when you open or close lid. 24 WARNING: To avoid the risk of injury, do not open lid until

coffee machine has finished brewing cycle. 25 Hot steam or hot water trapped under lid could burn your

fingers. 26Only use capsules intended for this appliance. If the capsule

does not fit, do not force the capsule into the appliance. 27 Extension cords are available and may be used if care is

exercised in their use.

Warning: To reduce the risk of fire or electric shock, do not remove the bottom cover. No user-serviceable parts are inside. For assistance, call 1-866-4 Senseo (1-866-473-6736) or visit our website at www.senseo.us.

SAVE THESE INSTRUCTIONS

SPECIAL INSTRUCTIONS

This coffee machine has a short cord to reduce the hazards of becoming entangled in or tripping over a longer cord. An extension cord may be used if the rating is equal to or greater than the rating of the coffee machine. Use an extension cord rated 13 amperes or greater. Take care to arrange extension cord so that it does not hang over the edge of countertop or tabletop, where it can be pulled on by children or tripped over unintentionally. Operating the coffee machine and another appliance at the same time from the same electrical circuit could cause an electrical overload, which would blow the fuse or trip the circuit breaker.

SPECIAL POLARIZED PLUG INSTRUCTIONS

This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way.

DO NOT ATTEMPT TO DEFEAT THIS SAFETY FEATURE IN ANY WAY

WARNINGS:

To avoid risk of personal injury or damage to property as a

result of overflow, be sure that the cup or mug is centered

under the coffee outflow unit during the brewing cycle.

Brewed coffee and coffee pods are very hot. Handle with care

to avoid scalding.

If coffee outflow unit overflows or fails to drain into cup/mug

during the brewing cycle, do not open lid or handle coffee

outflow unit or coffee pod holder(s). Unplug coffee machine

and wait for contents to cool before you handle them.

Do not remove any part of coffee machine or cup/mug during

the brewing cycle as scalding could occur.

Use only fresh, cool water in this machine. Do not put any

other liquids in this machine except as instructed in chapter

‘Descaling’. Do not refill the water reservoir with hot water or

coffee.

DO NOT attempt to move coffee machine during the brewing

process. Let appliance cool down completely before you move

it.

Keep machine at least 4 inches (10cm) away from walls or

other objects while it operates. Do not place any object on top

of coffee machine while it operates.

PLEASE READ AND SAVE THIS INSTRUCTION MANUAL.

General description (Fig. 1)

1 Water reservoir 2 1-cup pod holder 3 2-cup pod holder 4 Cover of coffee outflow unit 5 Coffee outflow unit 6 Cup tray 7 Drip tray 8 Indicator light 9 Sealing ring 10 Water distribution disk

Introduction

With this SENSEO® coffee machine, you can enjoy a perfect cup of coffee topped with a rich frothy coffee layer whenever you feel like it. Each cup is freshly brewed, so you’re always sure of a pure and round taste. This SENSEO® coffee machine combines a unique brewing method with convenient coffee pods from SENSEO, available in different blends of fine roast and ground coffee. Together they make sure you only get the very best in flavor and aroma from the coffee. This new SENSEO machine offers you more choice as it has extra strength select settings. Next to the long, smooth SENSEO coffee, you can also choose to brew a short strong SENSEO coffee by simply pressing the button twice. The convenient SENSEO pods and the unique SENSEO® brewing system are perfectly matched to ensure that the best taste and aroma are extracted from the coffee. To optimize the taste of the coffee, keep the following aspects in mind:

Clean cold water

Use clean cold water every day. If you have not used the coffee machine for three days, you have to flush it with clean cold water before you use it again (see section ‘Flushing’ in chapter ‘Cleaning’).

Fresh coffee pods

Use the SENSEO® coffee pods that have been specially developed for your SENSEO® coffee machine for a full, round taste. SENSEO® coffee pods stay fresh longer when you store them in a storage container.

A clean machine

Clean and descale the SENSEO® coffee machine regularly (see chapters ‘Cleaning’ and ‘Descaling’). Remove used coffee pods after brewing. If a used pod has been left in the coffee machine and you have not used the machine for some time, flush the machine before you use it again (see section ‘Flushing’ in chapter ‘Cleaning’). For more information on why it is important to descale, how to descale or which descaler to use, visit our website.

Intensity select

For one small cup of strong short coffee, double tap the 1-cup button.

For two cups of strong short coffee, double tap the 2-cup button.

First use

Unpacking

1 Remove the machine from the box.

Note: Make sure you store the 2-cup pod holder in a safe

place. It is an essential part of the machine.

Flushing the machine to fill the system

Warning: You cannot brew coffee if you have not flushed the SENSEO® coffee machine first!

The flushing cycle causes the system to fill with water. After this, the coffee machine is ready for use. Flush the machine in the following way:

1 Remove the water reservoir (Fig. 2). 2 Fill the water reservoir with clean cold water up to the MAX

indication and put it back onto the machine (Fig. 3). 3 Move the lever upwards to release the lid (Fig. 4). 4 Open the lid (Fig. 5). 5 Put the 1-cup pod holder or the 2-cup pod holder in the

machine without pod(s) (Fig. 6). 6 Close the lid and lock the lever (Fig. 7).

Note: Make sure you lock the lever properly. Push it down until

it snaps home with a click.

Note: Never flush the machine with the lid open. The lid must

be properly locked. 7 Put the plug in a polarized electrical outlet.

8 Put a bowl with a capacity of at least at least 1.6 qt (1.5 liters)

under the coffee outflow unit to collect the water (Fig. 8). 9 Press the on/off button and subsequently press the 1-cup

button and the 2-cup button briefly at the same time (Fig. 9).

The system fills itself with water from the water reservoir. This takes some time (approx. 90 to 150 seconds). The machine switches off automatically when the flushing cycle ends. During the flushing cycle, the machine produces more noise than during a regular brewing cycle.

Note: Before you use the machine for the first time, clean the coffee outflow unit and the pod holders with hot water and some washing-up liquid or in the dishwasher. Clean the water reservoir thoroughly in hot water, if necessary with some washing-up liquid (see chapter 'Cleaning the machine').

Now your SENSEO® coffee machine is ready for use.

Brewing SENSEO® coffee

Filling the water reservoir

1 Fill the water reservoir with clean cold water up to the MAX

indication and put it back onto the machine (Fig. 3).

Warning: Never pour any other liquid than clean cold water

into the water reservoir.

MIN: minimum amount of water required to brew 1 cup of

SENSEO® coffee.

A full reservoir allows you to make SENSEO® coffee a number

of times. This makes it unnecessary to fill the water reservoir

each time you want to make a cup of coffee.

Turning on the machine

1 Press the on/off button (Fig. 10).

The indicator light flashes while the water heats up. Heating up takes approx. 90 seconds.

The coffee machine is ready for use when the indicator light lights up continuously.

Placing a pod holder

1 Move the lever upwards to release and open the lid (Fig. 4). 2 Place the SENSEO® coffee pod(s) properly in the center of the

pod holder, with the convex side pointing downwards.

Place 1 SENSEO® coffee pod in the 1-cup pod holder to brew one cup of coffee (Fig. 11).

Place 2 SENSEO® coffee pods in the 2-cup pod holder to brew two cups of coffee (Fig. 12).

Note: Use SENSEO® coffee pods that have been specially

developed for your SENSEO® coffee machine for a full and

round taste.

Note: Make sure the pod holder is clean and the sieve in the

center is not clogged, e.g. with loose coffee grounds.

Note: Make sure the coffee in the pod(s) is evenly distributed

and press the pod(s) lightly into the pod holder. 3 Close the lid and lock the lever (Fig. 7).

Always make sure the lid is properly locked. Push down the lever until it snaps home with a click.

Warning: Never start brewing with the lid open. The lid

must be properly closed.

Brewing coffee

1 Place one cup or two cups under the coffee outflow unit. The

cups you use should have a capacity of at least 5.0fl.oz.

(150ml). Do not use cups that are too large, as they cause the

coffee to get cold more quickly. 2 Press the button that indicates the number of cups of

SENSEO® coffee you want to brew.

Press the 1-cup button once for one large mild cup of coffee (Fig. 13).

Tip: Press the same button twice for one strong small cup of

coffee. The indicator light shines less bright to indicate you

have pressed the same button twice.

Press the 2-cup button once for two large mild cups of coffee (Fig. 14).

Tip: Press the same button twice for two strong small cups of

coffee. The indicator light shines less bright to indicate you

have pressed the same button twice.

The SENSEO® coffee machine starts brewing. The machine automatically supplies the optimal amount of water.

Warning: Do not remove the water reservoir during a

brewing cycle, as this will cause the machine to draw in air.

3 After use, lift the pod holder out of the machine and remove

the coffee pod(s). Be careful when you do this, for there may

still be some water/coffee on the coffee pod(s). 4 After use, press the on/off button to switch off the machine.

Note: If you do not use the machine, it switches off

automatically after 30 minutes to save energy.

Note: Never put normal ground coffee or use torn pods in the

SENSEO® machine, as this causes it to become blocked.

Cleaning the machine

Never immerse the machine in water or any other liquid.

Never clean the machine by flushing it with the lid open.

Cleaning the coffee machine

1 Always unplug the machine before you clean it. 2 Clean the outside of the machine with a moist cloth. 3 Remove the coffee outflow unit (Fig. 15).

You can disassemble the coffee outflow unit for more thorough cleaning (Fig. 16).

4 Clean the coffee outflow unit, the pod holders, the drip tray,

the cup tray and the water reservoir in hot water, if necessary

with some dishwashing liquid, or in the dishwasher (Fig. 17). 5 To prevent clogging, clean the pod holders regularly with hot

water, some dishwashing liquid and a dishwashing brush. If

you have used the 2-cup pod holder to brew cappuccino or

hot chocolate, make sure to clean it thoroughly immediately

after use to remove any milk residues (Fig. 18).

Note: Use the pod holder in the machine during descaling to

clean it even more effectively. 6 Clean the water distribution disk with a moist cloth. Be careful

when you do this. Make sure that the rubber sealing ring does

not get stuck under the edge of the water distribution disk. If it

does, the coffee machine starts to leak (Fig. 19).

Flushing the coffee machine

If you have not used the coffee machine for three days, flush it with clean cold water before you use it again. Flush the machine in the following way:

1 Fill the water reservoir with clean cold water up to the MAX

indication and put it back onto the machine (Fig. 3). 2 Put the 1-cup pod holder or the 2-cup pod holder in the

machine without pod(s) (Fig. 6). 3 Put a bowl with a capacity at least 1.6 qt (1.5 liters) under the

coffee outflow unit to collect the water (Fig. 8). 4 Press the on/off button. Wait until the machine has heated up.

Then press the 2-cup button several times until the water

reservoir is empty (Fig. 20).

Descaling

When to descale

Descale the SENSEO® coffee machine frequently. Preferably descale 4 to 6 times a year, but at least once every 3 months. There is no difference between soft-water and hard-water areas in this respect. Descaling takes about 30 minutes. Do not interrupt the descaling process.

Why to descale

Scale builds up inside the machine during use. It is essential to descale the SENSEO® coffee machine at least every 3 months. Your reasons to descale:

It prolongs the life of your SENSEO® coffee machine

It ensures maximum cup volume

It ensures maximum coffee temperature

The machine produces less sound during brewing

It prevents malfunctioning If the descaling procedure is not performed correctly, scale

residue remains behind in the machine. This causes scale to build up more quickly and may cause permanent and irreparable damage to the machine.

Use the correct descaler

Only citric acid-based descalers are suitable for descaling the SENSEO® machine. This type of descaler descales the machine without damaging it. For the correct amount, see under ‘Descaling procedure’ below. Each descaling mixture can be used only once. Use a new descaling mixture each time.

Descaling procedure

The descaling procedure consists of 2 descaling cycles, each with 1 liter of descaling mixture, and 2 flushing cycles. Do not interrupt the descaling cycles and do not switch off the machine before or between the flushing cycles.

1 Press the on/off button to turn on the machine (Fig. 10). 2 Place the 1-cup pod holder with a used coffee pod in it in the

coffee machine. Close the lid and make sure it is properly

locked. 3 Mix the descaler powder with 1 quart (1 liter) of water in a

measuring jug. Stir until the powder is completely dissolved

(Fig. 21).

Note: You have to use 2 quarts (2 liters) of descaling mixture:

one liter for each descaling cycle.

4 Fill the water reservoir up to the MAX indication with the

descaler mixture (Fig. 21). 5 Put the water reservoir back into the coffee machine. The

machine is ready for use when the indicator light lights up

continuously. 6 Put a bowl with a capacity of at least 1.6 qt (1.5 liters) under the

coffee outflow unit to collect the descaling mixture (Fig. 8). 7 Press the 2-cup button once and let the machine operate.

Repeat this until the water reservoir is empty.

Note: Make sure that you use up the descaling mixture

completely during the descaling cycle.

Warning: Never interrupt the descaling cycle.

8 Exchange the 1-cup pod holder for the 2-cup pod holder.Place

a used pod in the 2-cup pod holder and close the lid. 9 Repeat steps 3 to 7.

Warning: Never descale the SENSEO® coffee machine with

the lid open. Make sure the lid is properly locked.

10 Remove the used pod and clean both pod holders after

descaling with hot water and a dishwashing brush to prevent

the sieve in the center from getting clogged. 11 Rinse the water reservoir with clean cold water. Fill the water

reservoir up to the MAX indication with clean cold water and

repeat steps 5 to 7.

Note: Do not refill the water reservoir with used hot water or

the used descaling mixture. 12 Rinse the water reservoir once again with clean cold water. Fill

the water reservoir with clean cold water up to the MAX

indication and repeat steps 5 to 7 once more.

Note: Always rinse the machine by letting it empty two full

water reservoirs.

Frost-free storage

If the coffee machine has already been used and therefore has been flushed with water, it may only be used and stored in a frost-free place to prevent it from becoming damaged.

Assistance

For assistance, call 1-866-4 Senseo (1-866-473-6736) or visit our website at www.senseo.us.

Disposal

Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. For recycling information, please contact your local waste management facilities.

Warranty

Eximius Coffee LLC (Eximius) hereby warrants that, if your SENSEO® Single Serve Gourmet Coffee Maker Model (except cord, coffee pods and accessories) is found to be defective in materials or workmanship during the period of one year from the date of purchase, Eximius will, at its option, either (1) repair or replace any defective product without charge to you, or (2) refund your purchase price.

This warranty extends only to the original retail purchaser. IMPORTANT: This warranty does not cover damage resulting from

accident, misuse or abuse, lack of reasonable care, the affixing of any attachment not provided with the product, loss of parts, or subjecting the product to any but the specified voltage. Use of unauthorized replacement parts will also void this warranty. Eximius will not pay for warranty service performed by a nonauthorized repair service.

In order to obtain warranty service, call our SENSEO® Consumer Affairs Hotline at 1-866-473-6736. You will need proof of purchase to obtain a warranty remedy.

REPAIR, REPLACEMENT OR REFUND (AT THE OPTION OF EXIMIUS)

IS YOUR ONLY REMEDY UNDER THE ABOVE WARRANTY. EXIMIUS SHALL NOT BE LIABLE FOR ANY OTHER INCIDENTAL, CONSEQUENTIAL OR INDIRECT COSTS, EXPENSES OR DAMAGES NO OTHER WARRANTY, WRITTEN OR ORAL, IS AUTHORIZED BY EXIMIUS. ALL IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THE APPLICABLE WRITTEN WARRANTY ABOVE.

Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.

Read the instructions enclosed with your Senseo coffee machine carefully.

Manufactured for: Eximius Coffee LLC 5610 Clinton Dr, Houston, TX 77020 The United States of America Call 1-866-4 Senseo (1-866-473-6736) or visit our website:

www.senseo.us. SENSEO® is a registered trademark.

Troubleshooting

If you experience a problem with your coffee machine, you may find the solution in the table below. If the table does not provide the solution to your problem or if you have a question, call 1-866-4 Senseo (1-866-473-6736) or visit our website at www.senseo.us.

Problem Possible cause Solution

My coffee cup overflows with cold coffee

You did not flush the machine before first use.

Flush the machine before first use.When the machine has emptied a complete water reservoir, you can start to make a new coffee.

The indicator light flashes slowly.

The indicator light flashes quickly.

The coffee is not hot enough.

The coffee temperature in the cup decreases quickly.

The machine is heating up.

There is not enough water in the water reservoir

The float in the water reservoir may be stuck.

You have used the machine for a longer period without descaling.

Do not use cups that are too large.

If this takes longer than two minutes, call 1-866-4 Senseo (1-866-473-6736) or visit our website at www.senseo.us.

Fill the water reservoir and make sure you place the water reservoir properly into the machine.

Empty the water reservoir and shake it a few times to release the float. Clean the water reservoir with hot water and some washing-up liquid or in the dishwasher.

Perform the descaling procedure as described in chapter ‘Descaling’.

Use thin-walled cups. Thin-walled cups absorb less heat from the coffee than thick-walled cups.

Problem Possible cause Solution

You can preheat the coffee machine and cup by brewing a cup of hot water first without placing a coffee pod in the pod holder.

Intensity select: after pressing the coffee button twice, I do not get a stronger coffee.

I cannot open the lid.

The coffee machine produces less coffee than before.

You have pressed the coffee button twice too fast or you have waited longer than 3 seconds after pressing the button for the first time.

A temporary vacuum has developed under the lid.

Perhaps the sieve in the center of the pod holder is clogged.

Pressing the coffee button twice to get a stronger coffee is possible within a time frame of 3 seconds. The indicator light shines less bright when the strength selection is successful.

Switch off the coffee machine. Pull up the lever and wait 24 hours before you open the lid. You may need to use some force. Always make sure the pod holders are clean and the sieve is not clogged to prevent vacuum.

If the sieve is clogged, use a dishwashing brush to unclog the sieve. If you cannot unclog it properly with the dishwashing brush, put the pod holder in the machine and descale the machine. Descale the machine (see chapter ‘Descaling’).

I cannot close the lid properly.

The coffee is not strong enough.

Perhaps you have pressed the 1-cup or 2-cup button twice.

Perhaps a used coffee pod is sticking to the water distribution disk.

You may not have used the right number of pods or may have pressed the wrong button.

The pod(s) may not have been placed in the pod holder properly.

This new SENSEO machine offers you more choice as it has extra strength select settings. Next to the long, smooth SENSEO coffee, you can also choose to brew a short strong SENSEO coffee by simply pressing the button twice.

If this is the case, remove the used pod.

Use 1 pod in combination with the 1-cup pod holder and the 1-cup button. Use 2 pods in combination with the 2-cup pod holder and the 2-cup button.

Place the coffee pod(s) properly in the center of the pod holder, to prevent water from escaping along the edge of the pod(s). When you use two coffee pods on top of each other, make sure that the convex sides of both pods point downwards and press the pods lightly into the pod holder. Make sure that the coffee in the pod is distributed evenly.

The coffee is too strong.

Water leaks from the coffee machine.

You may have used the same pod twice.

Perhaps you need a different flavor.

Perhaps you have not discovered the new strength select feature to brew a short strong coffee.

Perhaps you need a different flavor.

You have not closed the lid properly.

Place a new pod in the pod holder to brew a fresh cup of coffee.

If you prefer a more robust flavor, SENSEO® coffee pods with a stronger blend are available.

If you prefer a milder flavor, SENSEO® coffee pods with a milder blend are available.

Close the lid properly and lock the lever.

You overfilled the water reservoir.

The sieve in the center of the pod holder may be clogged.

The sealing ring may be stuck under the edge of the distribution disk.

Water drops on the worktop may be the result of placing the water reservoir or removing and removing used pod(s).

Do not fill the water reservoir beyond MAX level.

Check the pod holder. If the sieve is clogged, use a dishwashing brush to unclog the sieve. If you cannot clean it properly with the dishwashing brush, put the pod holder in the machine and descale the machine (see chapter ‘Descaling’).

Check if the sealing ring is stuck under the edge of the distribution disk. If it is, pull it out from under the distribution disk carefully.

Check if the water drops on the countertop are not the result of placing or removing the water reservoir or removing used coffee pods. Make sure that you do not remove the water reservoir when the coffee machine is heating up. This may cause water that normally ends up in the water reservoir to leak out of the machine.

The machine has been stored in a room that was not frost-free.

In all other cases, call 1-866-4 Senseo (1-866-473-6736) for assistance or visit our website at www.senseo.us.