PHILIPS GC4932 User Manual [fr]

1 2

1-9

1-1

1-8

1-7

~2 min.

3-6

3-5

~2 min.

2-32-2

2-5

3-2 3-4

3-9

3-11 3-12

3-7

3-10

3-8

1-6

1-10

1-5

1-2

1-3

3-32-4

2-72-6

2-9

2-8

~30 sec.

2-1

~30 sec.

3-1

4-1

4-2

4-3

4-4

1-4

2-11

2-10

GC4930 series

ENGLISH 7 FRANÇAIS 11 ITALIANO 15 ESPAÑOL 19 PORTUGUÊS 23

1 2 3 4 5

4239 001 08152

User manual

Mode d’emploi Manuale utente

Manual del usuario

Manual do utilizador

GC4930 series

EN To use FR Utilisation IT Utilizzo ES Para usar PT Para utilizar

1 2

1-1

1-5

1-9

1-2

1-6

1-10

1-3

1-7

~2 min.

1-4

1-8

EN Quick Calc Release (specic types only) FR Quick Calc Release (certains modèles uniquement) IT Sistema rapido di pulizia anticalcare (solo alcuni modelli) ES Liberación rápida de la cal (solo modelos especícos) PT Quick Calc Release (apenas em modelos especícos)

2-1

2-5

2-9

~30 sec.

2-10

2-32-2

2-72-6

2-11

2-8

EN Calc-Clean (specic types only) FR Calc Clean (certains modèles uniquement) IT Calc-Clean (solo alcuni modelli) ES Calc-Clean (solo modelos especícos) PT Calc-Clean (apenas em modelos especícos)

3-1

3-5

~2 min.

3-9

3-2 3-4

~30 sec.

3-6

3-10

3-32-4

3-7

3-11 3-12

3-8

EN To store FR Rangement IT Conservazione

ES Para guardar PT Para armazenar

4-1

4-2

4-3

4-4

ENGLISH

Introduction

Congratulations on your purchase and welcome to Philips! To fully benet from the support that Philips oers, register your product at www.philips.com/welcome.

Read this user manual and the important information leaet carefully before you use the appliance. Save them for future reference.

Product overview

1 Water tank lid 2 Steam slider Steam on Steam o 3 Steam boost button 4 ‘Iron ready’ light 5 Calc-Clean / Quick Calc Release reminder light 6 Mains cord 7 Cord winding 8 Calc-Clean button (specic types only) 9 Soleplate 10 Quick Calc Release (specic types only)

Exclusive technology from Philips

OptimalTEMP technology

The OptimalTEMP technology enables you to iron all types of ironable fabrics, in any order, without adjusting the iron temperature and without sorting your garments.

It is safe to just rest the hot soleplate directly on the ironing board without putting back to the iron platform. This will help reduce the stress on your wrist.

This iron has been approved by The Woolmark Company Pty Ltd for the ironing of wool-only products, provided that the garments are ironed according to the instructions on the garment label and those issued by the manufacturer of this iron. R0000. The Woolmark symbol is a certication mark in many countries.

Using the appliance

Note: The iron may give o some smoke when you use it for the rst time. This stops after a short while.

Type of water to use

This appliance has been designed to be used with tap water. However, if you live in an area with hard water, fast scale build-up may occur. Therefore, it is recommended to use distilled or demineralized water to prolong the lifetime of the appliance.

Do not use perfumed water, water from the tumble dryer, vinegar, starch, descaling agents, ironing aids, chemically descaled water or other chemicals, as they may cause water spitting, brown staining or damage to your appliance.

ENGLISH

Ironable fabrics

1 Check whether the garment is ironable by reading the label on the garment (Fig. 1-5).

Do not iron non-ironable fabrics. Prints on the garment are not ironable either.

Iron with extra steam

Press and hold the steam boost trigger to get more steam to remove stubborn creases.

Auto shut-o

The auto shut-o function automatically switches o the appliance if it has not been used for 2 minutes resting on its soleplate or 8 minutes resting on its backplate. The ‘iron ready’ light ashes to indicate the appliance is at auto-o status.

To let the appliance heat up again, pick up the appliance or move it slightly. The ‘iron ready’ light turns to breathing and the appliance starts to heat up.

Cleaning and maintenance

For more information on how to performance clean and maintenance on the iron, refer to the videos in this link : http://www.philips.com/descaling-iron.

Cleaning the soleplate

1 Unplug the appliance and let it cool down. 2 Pour any remaining water out of the water tank. 3 Wipe akes and any other deposit o the soleplate with a damp cloth and a non-

abrasive (liquid) cleaning agent.

Note: To keep the soleplate smooth, avoid hard contact with metal objects. Never use a scouring pad, vinegar or other chemicals to clean the soleplate.

Quick Calc Release (specic types only)

IMPORTANT: The Quick Calc Release automatically collects loose scale particles during ironing. After 1 to 3 months of use, the Calc-Clean reminder light starts ashing to remind you to use the Quick Calc Release function (Fig. 2-1). This is to remove scales collected from your iron to prolong its life. When the Calc-Clean reminder light is ashing, the iron does not heat up.

Tip: The Quick Calc Release function can be used at any time, even when the reminder light is not activated yet. If you live in a hard water area, use the function more frequently.

Do not perform the Quick Calc Release when the iron is hot. Do not pour water into the Quick Calc Release opening.

1 Unplug the appliance (Fig. 2-2) and make sure that the appliance is cool (Fig. 2-3).

2 Hold the appliance in vertical position over the sink.

3 Flip up the lever of Quick Calc Release collector (Fig.2-4) and pull out the collector

(Fig.2-5).

4 Clean the Quick Calc Release collector with water (Fig. 2-6, Fig. 2-7).

ENGLISH

5 Gently shake the appliance to allow scale particles to fall out (Fig. 2-8).

6 Insert the Quick Calc Release collector back into the appliance (Fig. 2-10).

7 Push down the lever (“click”) to lock the collector (Fig. 2-11).

Calc-Clean (specic types only)

IMPORTANT: After 1 to 3 months of use, the Calc-Clean reminder light starts ashing to remind you to use the Calc-Clean function (Fig. 3-1). This is to remove scales in your iron to prolong its life.

Tip: The Calc-Clean function can be used at any time, even when the reminder light is not activated yet. If you live in a hard water area, use the function more frequently.

1 Make sure that the steam slider is set to “steam o” position (Fig. 3-2).

2 Make sure there is enough water (more than 3/4) in the water tank. If there is not

enough water, unplug the iron, ll the water to MAX indication (Fig.3-3) and plug in the iron again (Fig.3-4).

Do not pour vinegar or other descaling agents into the water tank.

3 Wait for the iron to heat up. This takes about 2 minutes (Fig.3-5).

Note: the Calc-Clean reminder light turns o during heating up. .

4 Unplug the iron when the ‘iron ready’ light stops breathing (Fig. 3-7).

5 Hold the iron over the sink. Keep pushing the Calc-Clean button and gently shake

the iron forth and back until all water in the water tank has been used up (Fig. 3-8).

Scales is ushed out, steam and boiling water also come out of the soleplate. Note: Repeat steps 2 to 5 if the water that comes out of the appliance still contains

scale particles.

6 Plug in the appliance and let the appliance heat up to dry the soleplate. This takes

about 2 minutes (Fig. 3-9).

7 Unplug the appliance (Fig. 3-10). Move the appliance gently over a piece of cloth to

remove any water stains on the soleplate (Fig. 3-11).

Troubleshooting

This chapter summarises the most common problems you could encounter with the appliance. If you are unable to solve the problem with the information below, visit www.philips.com/support for a list of frequently asked questions or contact the Consumer Care Centre in your country.

Problem Possible cause Solution

The iron cannot remove wrinkles from the garment.

The iron does not produce any steam.

There is no steam during ironing.

There is not enough water in the tank.

The steam slider is set to . Set the steam slider to .

Fill the water tank and set the steam slider to .

Fill the water tank.

ENGLISH

Problem Possible cause Solution

Water droplets drips onto the garment during ironing.

The iron does not produce a steam boost.

Dirty water and impurities come out of the soleplate during ironing.

Water drips from the soleplate after the iron has been unplugged.

There is an amber light ashing on the handle of the iron.

The iron leaves a shine or an imprint on the garment.

The iron is not hot enough yet to product steam.

You have used the steam boost function too often within a short period.

You have not closed the water tank lid properly.

You have not insert the Quick Calc Release collector properly back to the appliance (specic types only).

You have used the steam boost function too often within a short period.

The iron is not hot enough for ironing yet.

You have put a chemical into the water tank.

Hard water with impurities or chemicals has formed akes inside the soleplate.

You have put the iron in horizontal position with water still left in the water tank.

The steam slider is set to . Set the steam slider to . The Calc-Clean reminder light

is activated. This is to remind you to perform calc clean.

The surface to be ironed was uneven, for instance because you ironed over a seam or a fold in the garment.

Wait until the ‘iron ready’ light has stopped breathing and lights up steadily.

Continue ironing in horizontal position and wait a while before you use the steam boost function again.

Press the lid until you hear a ‘click’.

Stop ironing and let the iron cools down for at least 1 hour. Take out the Quick Calc Release collector. Insert it back into the appliance and ensure the collector is in-line with the surface of the appliance. Push down the lever (“click”). If the Quick Calc Release collector is damaged, contact a consumer care center in your country (see the world wide guarantee leaet for contact details).

Continue ironing in horizontal position and wait a while before you use the steam boost function again.

Wait until the ‘iron ready’ light has stopped breathing and lights up steadily.

Rinse the water tank and do not put any perfume or chemicals into the water tank.

Perform Quick Calc Release (specic types only) or Calc-Clean (specic types only). See chapter “Cleaning and maintenance”.

Empty the water tank after use, or store the iron in vertical position.

Perform Quick Calc Release (specic types only) or Calc-Clean (specic types only). See chapter “Cleaning and maintenance”.

The iron is safe to use on all ironable garments. The shine or imprint is not permanent and disappears when you wash the garment. Avoid ironing over seams or folds. You can also place a cotton cloth over the area to be ironed to avoid imprints.

FRANÇAIS

Introduction

Félicitations pour votre achat et bienvenue dans l'univers Philips ! Pour proter pleinement de l'assistance oerte par Philips, enregistrez votre produit à l'adresse suivante : www.philips.com/welcome.

Lisez attentivement ce mode d'emploi et la brochure « Informations importantes » avant d'utiliser l'appareil. Conservez-les pour un usage ultérieur.

Présentation du produit

1 Couvercle du réservoir d'eau 2 Curseur de vapeur Vapeur activée Vapeur désactivée 3 Bouton Eet pressing 4 Voyant « Fer prêt » 5 Voyant de rappel Calc Clean / Quick Calc Release 6 Cordon d'alimentation 7 Système d'enroulement du cordon 8 Bouton Calc Clean (certains modèles uniquement) 9 Semelle 10 Quick Calc Release (certains modèles uniquement)

Technologie exclusive de Philips

Technologie OptimalTEMP

La technologie OptimalTEMP vous permet de repasser tous les types de tissus repassables, dans l'ordre que vous souhaitez, sans avoir à régler la température du fer ni à trier vos vêtements.

Vous pouvez laisser la semelle chaude reposer directement sur la planche à repasser sans la redéposer sur le support du fer à repasser. Cela permettra de réduire la pression exercée sur votre poignet.

Ce fer a été approuvé par The Woolmark Company Pty Ltd pour le repassage de vêtements en laine à condition que ceux-ci soient repassés selon les instructions indiquées sur l’étiquette du vêtement et celles fournies par le fabricant du fer. R0000. Le symbole Woolmark est une marque de certication dans de nombreux pays.

Utilisation de l'appareil

Remarque : lors de la première utilisation, le fer peut dégager un peu de fumée. Cela s'arrête après un bref instant.

Type d'eau à utiliser

Cet appareil a été conçu pour être utilisé avec de l'eau du robinet. Cependant, si vous habitez dans une zone où l'eau est très calcaire, des dépôts peuvent se former rapidement. Par conséquent, il est recommandé d'utiliser de l'eau distillée ou déminéralisée pour prolonger la durée de vie de l'appareil.

+ 15 hidden pages