Specialist Vacuum cleaner
FC 9102
/A
/B
/C
Philips Domestic Appliances and Personal Care
Service Manual
PRODUCT INFORMATION
- Colour /A : Ice Blue
/B : Mauve metallic
Version /C : 2000 W logo
- Maximum air displacement : 37 l/sec.
- Maximum vacuum water column : 310 cm
- Power consumption (IEC) 230 V : 1500 W
- Duststorage capacity : 3 L
- Type number dustbag : FC 8021
- Cord length (depends on version) : 7 metres
- Filter system : Paper dustbag
: Exhaust AFS air fi lter
: Motor inlet fi lter
- Dimensions of cleaner : 460 x 315 x 270 mm
- Dimensions of packaging : 595 x 395 x 295 mm
- Net weight : 5.88 kg
- Gross weight : 9.135 kg
OPTIONAL
- FC 8021 S-bags
- FC 8030 AFS-fi lter
- FC 8031 HEPA Air Filter
- FC 8034 Upgrate kit Active Carbon Filter
- HR 6988 Turbo brush nozzle
- HR 8040 Polishing nozzle
C 2x
C 9x
Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification
SERVICE INFORMATION
- Open the appliance, fi rst remove the exhaust fi lter grille (item 20),
and then remove the 2 screws - C of the switch control panel
(item 15).
- Undo and remove the 9 screws - C in the upper housing (item 8).
You will require a screwdriver with a 14.5 cm-long shank for this.
Depending on the version screwdriver 9965 000 08332 for cross
head or onwards 0234 screwdriver 4322 009 08490 for T15 can
be used.
- The component confi guration shown in the exploded view may
differ in case of specifi c versions. The components are
distinguished by means of code numbers.
- When the repair is fi nished, check whether all functions of the
appliance work properly.
- Item 4, cotton dustbag, is used in countries in which paper
dustbags are not available.
- To disassemble the cord winder, use TORX screwdriver no.T15,
which is one of a set consisting of T20; T15; T10; T9; T8; T7 and
T6 (code number 4822 395 50145).
- If the reel half spring unit is replaced, shaft A must be lubricated
with silicone grease. Do not apply any silicone grease to or spill
any grease on terminals (43) or conductors (42).
- Item 40 is provided with a long cord-winder spring, but both long
and short cords can be used in combination with this spring.
(L = 9.3 m)
- Depending on the original cord, the spare cord must be shortened
to the length of the original cord.
- The cord winder spring must be tensioned to the maximum level
and then be rewound approx. 1.5 turn
- Item 13, air valve, opens to cool the motor if the air displacement
is too low or if the airfl ow is blocked.
- To adjust the telescopic tube (item 59) to the required length,
push the adjustment collar in the direction of the arrow while
sliding the top section of the telescopic tube into or out of the
lower section.
- If the function of the electronic control unit (item 12) is not
required, the Triac must be short-circuited in the manner shown in
the circuit diagram.
- When the vacuum cleaner is used to suck up fi ne dust the pores
of the dustbag may become clogged, causing the passage of air
through the dustbag to become obstructed. As a result, the
dustbag-full indicator will indicate that the dustbag needs to be
replaced, eventhough the dustbag is not full at all.
4322 277 00575
02/05
Pos. Order code description
1 4322 009 08070 Dust cover /A
4322 009 08130 Dust cover /B
2 4322 003 18280 Dust cover lock grey
3 4322 003 18150 Dustbag holder
4 4822 480 10113 S-paper dustbags FC 8021
4322 004 93290 Cotton dustbag
5 4322 003 18300 Cordwinder lever
6 4322 001 73310 Sealing rim
7 4322 005 12550 Dustbag detector
8 4322 003 18050 Upper housing l.grey
8a 4322 003 20410 Clamp upper/lower housing
9 4322 000 37300 Triple fi lter
10 4322 009 07040 Grill + triple fi lter
11 4322 006 21480 Switch soldered version
11a 4322 009 08420 Switch lever assy
12 4322 006 22560 PCB slide turn 230V
13a 4322 005 12200 Dustbag full indicator
13b 4322 005 12210 Air valve
14 4322 003 18090 Handle l.grey
15 4322 009 08140 Panel slide /A
4322 009 08200 Panel slide /B
16 4322 003 17890 Lower housing l.grey
17 4322 003 18100 Handle lock
18 4322 000 37450 Silencer 4 wall
19 4322 005 12180 Caster assy l.grey
20 4322 009 08210 Exhaust grille /A
4322 009 08260 Exhaust grille /B
21 4322 000 37460 Exhaust diffusor
22 4322 004 92910 Electr.static fi lter FC 8030
23 4322 001 73280 Filter sealing
24 4322 003 18000 S-class sealing
25 4322 000 37420 Silencer 1 wall
26 4322 000 37430 Silencer 2 bottom
27 4322 003 18070 Cord outlet l.grey
28 4322 003 18910 Rear wheel lock red
29 4322 003 11990 Receipt. housing A.C.
30 4322 003 17950 Rear wheel l.grey
31 4322 001 73300 Motor buffer back
32 4322 003 18040 Inlet sealing
33 4322 003 18010 Motor cap top
34 4322 003 18020 ANS disc
35 4322 001 73290 Motor bufferring front
36 4322 009 06430 Motor A 1441 230V
37 4322 000 37440 Silencer 3 ans
38 4322 003 18030 Motor cap bottom
Pos. Order code description
40 4322 009 07940 Reel half spring unit (L = 9m)
41 4322 001 72360 Brake tyre
42 4322 009 07950 Reel half contact unit
43 4322 009 07970 Contact ring plate
44 4322 006 01440 Argentina L = 9.3 m
4322 006 01760 Australia L = 9.3 m
45 4322 006 01680 Taiwan L = 6.3 m
46 4322 006 01720 U.K. / H.K. L = 9.3 m
47 4322 006 01410 Euro 4.8 mm pins L = 9.3 m
48 4322 006 01670 Swiss L = 9.3 m
49 4322 006 01460 Italy L = 9.3 m
50 4322 003 18850 C-bend B1
51 4322 005 12720 C-bend B1 hose sw assy
54 4322 007 16000 Leaf spring assy
55 4322 004 22570 Plumeau assy
56 4322 003 18870 Crevice nozzle
57 4322 005 12530 Acc. bridge assy
59 4322 004 22510 Telesc. tube st. silver complete
60 4322 001 99120 Tube bush
61 4322 007 45550 Tube spring
62 4322 004 22560 Small nozzle
63 4322 004 22490 R&C nozzle standard l.grey
A 5322 390 20011 Silicon grease for shaft
B 4322 002 82550 Screw 3.5 x 12 T10
C 4322 002 82080 Screw 3.5 x 19
This product meets the requirements regarding interference suppression on radio and TV.
After the product has been repaired, it should
function properly and has to meet the safety
requirements as offi cially laid down at this
moment.
MOTOR
POWER
MODULE
Black
Black
Blue
Brown
M
CORD WINDER
Triac
Short-circuit